[PATCH 4/7] drm/bridge: tc358767: fix initial DP0/1_SRCCTRL value

[Tomi Valkeinen]

On 19/11/18 09:29, Andrzej Hajda wrote:
> On 29.10.2018 12:46, Tomi Valkeinen wrote:
>> Initially DP0_SRCCTRL is set to a static value which includes
>> DP0_SRCCTRL_LANES_2 and DP0_SRCCTRL_BW27, even when only 1 lane of
>> 1.62Gbps speed is used. DP1_SRCCTRL is configured to a magic number.
>>
>> This patch changes the configuration as follows:
>>
>> Configure DP0_SRCCTRL by using tc_srcctrl() which provides the correct
>> value.
>>
>> DP1_SRCCTRL needs to bits to be set to the same value as DP0_SRCCTRL:
> 
> s/to/two/
> 
> 
>> SSCG and BW27. All other bits can be zero.
>>
>> Signed-off-by: Tomi Valkeinen <tomi.valkeinen at ti.com>
>> ---
>>  drivers/gpu/drm/bridge/tc358767.c | 11 +++++------
>>  1 file changed, 5 insertions(+), 6 deletions(-)
>>
>> diff --git a/drivers/gpu/drm/bridge/tc358767.c b/drivers/gpu/drm/bridge/tc358767.c
>> index fee53422c31f..ab299f4debfa 100644
>> --- a/drivers/gpu/drm/bridge/tc358767.c
>> +++ b/drivers/gpu/drm/bridge/tc358767.c
>> @@ -836,12 +836,11 @@ static int tc_main_link_setup(struct tc_data *tc)
>>  	if (!tc->mode)
>>  		return -EINVAL;
>>  
>> -	/* from excel file - DP0_SrcCtrl */
>> -	tc_write(DP0_SRCCTRL, DP0_SRCCTRL_SCRMBLDIS | DP0_SRCCTRL_EN810B |
>> -		 DP0_SRCCTRL_LANESKEW | DP0_SRCCTRL_LANES_2 |
>> -		 DP0_SRCCTRL_BW27 | DP0_SRCCTRL_AUTOCORRECT);
>> -	/* from excel file - DP1_SrcCtrl */
>> -	tc_write(DP1_SRCCTRL, 0x00003083);
>> +	tc_write(DP0_SRCCTRL, tc_srcctrl(tc));
>> +	/* SSCG and BW27 on DP1 must be set to the same as on DP0 */
>> +	tc_write(DP1_SRCCTRL,
>> +		 (tc->link.spread ? DP0_SRCCTRL_SSCG : 0) |
>> +		 ((tc->link.base.rate != 162000) ? DP0_SRCCTRL_BW27 : 0));
> 
> 
> Wouldn't  be better then to modify tc_srcctrl to support DP0 and DP1:
> 
>     tc_write(DP0_SRCCTRL, tc_srcctrl(tc, 0));
> 
>     tc_write(DP1_SRCCTRL, tc_srcctrl(tc, 1));

In a normal case I would agree. But on this IC, there's only a single
DisplayPort output, DP0. However, for some reason, DP1_SRCCTRL also
needs to be configured (and the register is not even in the docs) for
DP0 to work. Possibly there are IC versions with two DP ports, but I
don't know how DP1_SRCCTRL needs to be configured on those.

So I'd rather keep the normal configuration (for DP0 with tc_srcctrl)
separate from setting these magical bits in DP1_SRCCTRL needed to make
the IC work.

 Tomi

-- 
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki