[PATCH v7 1/2] drm/panel: Add support for Truly NT35597 panel driver
Sean Paul
sean at poorly.run
Thu Sep 20 15:52:26 UTC 2018
On Wed, Sep 19, 2018 at 07:55:39PM -0700, Abhinav Kumar wrote:
> From: "abhinavk at codeaurora.org" <abhinavk at codeaurora.org>
>
> Add support for Truly NT35597 panel driver used
> in MSM reference platforms.
>
> This panel driver supports both single DSI and dual DSI
> modes.
>
> However, this patch series adds support only for
> dual DSI mode.
>
> Changes in v7:
> - Make the panel commands, name and mode as const
> - Configure the reset pin as active low in the device
> tree and adjust the reset sequence
> - Remove the macros to call the functions
> - Fix return conditions in the panel prepare call
> - Change the compatible string to have only the
> panel driver and the resolution details
>
> Signed-off-by: Archit Taneja <architt at codeaurora.org>
> Signed-off-by: Abhinav Kumar <abhinavk at codeaurora.org>
Hey Abhinav,
Thanks for revising the patch. I'm a bit torn on sending more feedback since
you're already on v7 and it's been on-list for a while. Unfortunately I think
there's enough to warrant a respin, so apologies for keeping this thing in
limbo, but hopefully we're converging.
> ---
> drivers/gpu/drm/panel/Kconfig | 8 +
> drivers/gpu/drm/panel/Makefile | 1 +
> drivers/gpu/drm/panel/panel-truly-nt35597.c | 706 ++++++++++++++++++++++++++++
> 3 files changed, 715 insertions(+)
> create mode 100644 drivers/gpu/drm/panel/panel-truly-nt35597.c
>
> diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
> index 6020c30..7ae74c2 100644
> --- a/drivers/gpu/drm/panel/Kconfig
> +++ b/drivers/gpu/drm/panel/Kconfig
> @@ -186,4 +186,12 @@ config DRM_PANEL_SITRONIX_ST7789V
> Say Y here if you want to enable support for the Sitronix
> ST7789V controller for 240x320 LCD panels
>
> +config DRM_PANEL_TRULY_NT35597_WQXGA
> + tristate "Truly WQXGA"
> + depends on OF
> + depends on DRM_MIPI_DSI
> + select VIDEOMODE_HELPERS
I don't think you're using the videomode stuff any longer?
> + help
> + Say Y here if you want to enable support for Truly NT35597 WQXGA Dual DSI
> + Video Mode panel
> endmenu
> diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
> index 5ccaaa9..80fd19f 100644
> --- a/drivers/gpu/drm/panel/Makefile
> +++ b/drivers/gpu/drm/panel/Makefile
> @@ -19,3 +19,4 @@ obj-$(CONFIG_DRM_PANEL_SEIKO_43WVF1G) += panel-seiko-43wvf1g.o
> obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o
> obj-$(CONFIG_DRM_PANEL_SHARP_LS043T1LE01) += panel-sharp-ls043t1le01.o
> obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o
> +obj-$(CONFIG_DRM_PANEL_TRULY_NT35597_WQXGA) += panel-truly-nt35597.o
> diff --git a/drivers/gpu/drm/panel/panel-truly-nt35597.c b/drivers/gpu/drm/panel/panel-truly-nt35597.c
> new file mode 100644
> index 0000000..a070d0f
> --- /dev/null
> +++ b/drivers/gpu/drm/panel/panel-truly-nt35597.c
> @@ -0,0 +1,706 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2018, The Linux Foundation. All rights reserved.
> + */
> +
> +#include <linux/gpio/consumer.h>
> +#include <linux/of_graph.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/pinctrl/consumer.h>
> +#include <linux/of_device.h>
> +
> +#include <video/mipi_display.h>
> +#include <video/of_videomode.h>
> +#include <video/videomode.h>
Same comment here re: videomode
> +
> +#include <drm/drmP.h>
> +#include <drm/drm_panel.h>
> +#include <drm/drm_mipi_dsi.h>
> +
> +static const char * const regulator_names[] = {
> + "vdda",
> + "vdispp",
> + "vdispn",
> +};
> +
> +static unsigned long const regulator_enable_loads[] = {
> + 62000,
> + 100000,
> + 100000,
> +};
> +
> +static unsigned long const regulator_disable_loads[] = {
> + 80,
> + 100,
> + 100,
> +};
> +
> +struct nt35597_config {
> + u32 width_mm;
> + u32 height_mm;
> + const char *panel_name;
> + const void *panel_on_cmds;
> + u32 num_on_cmds;
> + const struct drm_display_mode *dm;
> +};
> +
> +struct truly_nt35597 {
> + struct device *dev;
> + struct drm_panel panel;
> +
> + struct regulator_bulk_data supplies[ARRAY_SIZE(regulator_names)];
> +
> + struct gpio_desc *reset_gpio;
> + struct gpio_desc *mode_gpio;
> +
> + struct backlight_device *backlight;
> +
> + struct mipi_dsi_device *dsi[2];
> +
> + const struct nt35597_config *config;
> + bool prepared;
> + bool enabled;
> +};
> +
> +static inline struct truly_nt35597 *panel_to_ctx(struct drm_panel *panel)
> +{
> + return container_of(panel, struct truly_nt35597, panel);
> +}
> +
> +#define MAX_LEN 5
Aside from the ambiguous name, this is only used in one place and seems like
it's 1 byte too big. Could you please just declare commands as 'u8 commands[4];'
below?
> +#define SHORT_PACKET 2
> +#define LONG_PACKET 4
SHORT_PACKET and LONG_PACKET aren't used anywhere
> +
> +struct cmd_set {
> + u8 commands[MAX_LEN];
> + u8 size;
> +};
> +
> +static struct cmd_set qcom_2k_panel_magic_cmds[] = {
> + /* CMD2_P0 */
> + { { 0xff, 0x20 }, 2 },
> + { { 0xfb, 0x01 }, 2 },
> + { { 0x00, 0x01 }, 2 },
> + { { 0x01, 0x55 }, 2 },
> + { { 0x02, 0x45 }, 2 },
> + { { 0x05, 0x40 }, 2 },
> + { { 0x06, 0x19 }, 2 },
> + { { 0x07, 0x1e }, 2 },
> + { { 0x0b, 0x73 }, 2 },
> + { { 0x0c, 0x73 }, 2 },
> + { { 0x0e, 0xb0 }, 2 },
> + { { 0x0f, 0xae }, 2 },
> + { { 0x11, 0xb8 }, 2 },
> + { { 0x13, 0x00 }, 2 },
> + { { 0x58, 0x80 }, 2 },
> + { { 0x59, 0x01 }, 2 },
> + { { 0x5a, 0x00 }, 2 },
> + { { 0x5b, 0x01 }, 2 },
> + { { 0x5c, 0x80 }, 2 },
> + { { 0x5d, 0x81 }, 2 },
> + { { 0x5e, 0x00 }, 2 },
> + { { 0x5f, 0x01 }, 2 },
> + { { 0x72, 0x11 }, 2 },
> + { { 0x68, 0x03 }, 2 },
> + /* CMD2_P4 */
> + { { 0xFF, 0x24 }, 2 },
> + { { 0xFB, 0x01 }, 2 },
> + { { 0x00, 0x1C }, 2 },
> + { { 0x01, 0x0B }, 2 },
> + { { 0x02, 0x0C }, 2 },
> + { { 0x03, 0x01 }, 2 },
> + { { 0x04, 0x0F }, 2 },
> + { { 0x05, 0x10 }, 2 },
> + { { 0x06, 0x10 }, 2 },
> + { { 0x07, 0x10 }, 2 },
> + { { 0x08, 0x89 }, 2 },
> + { { 0x09, 0x8A }, 2 },
> + { { 0x0A, 0x13 }, 2 },
> + { { 0x0B, 0x13 }, 2 },
> + { { 0x0C, 0x15 }, 2 },
> + { { 0x0D, 0x15 }, 2 },
> + { { 0x0E, 0x17 }, 2 },
> + { { 0x0F, 0x17 }, 2 },
> + { { 0x10, 0x1C }, 2 },
> + { { 0x11, 0x0B }, 2 },
> + { { 0x12, 0x0C }, 2 },
> + { { 0x13, 0x01 }, 2 },
> + { { 0x14, 0x0F }, 2 },
> + { { 0x15, 0x10 }, 2 },
> + { { 0x16, 0x10 }, 2 },
> + { { 0x17, 0x10 }, 2 },
> + { { 0x18, 0x89 }, 2 },
> + { { 0x19, 0x8A }, 2 },
> + { { 0x1A, 0x13 }, 2 },
> + { { 0x1B, 0x13 }, 2 },
> + { { 0x1C, 0x15 }, 2 },
> + { { 0x1D, 0x15 }, 2 },
> + { { 0x1E, 0x17 }, 2 },
> + { { 0x1F, 0x17 }, 2 },
> + /* STV */
> + { { 0x20, 0x40 }, 2 },
> + { { 0x21, 0x01 }, 2 },
> + { { 0x22, 0x00 }, 2 },
> + { { 0x23, 0x40 }, 2 },
> + { { 0x24, 0x40 }, 2 },
> + { { 0x25, 0x6D }, 2 },
> + { { 0x26, 0x40 }, 2 },
> + { { 0x27, 0x40 }, 2 },
> + /* Vend */
> + { { 0xE0, 0x00 }, 2 },
> + { { 0xDC, 0x21 }, 2 },
> + { { 0xDD, 0x22 }, 2 },
> + { { 0xDE, 0x07 }, 2 },
> + { { 0xDF, 0x07 }, 2 },
> + { { 0xE3, 0x6D }, 2 },
> + { { 0xE1, 0x07 }, 2 },
> + { { 0xE2, 0x07 }, 2 },
> + /* UD */
> + { { 0x29, 0xD8 }, 2 },
> + { { 0x2A, 0x2A }, 2 },
> + /* CLK */
> + { { 0x4B, 0x03 }, 2 },
> + { { 0x4C, 0x11 }, 2 },
> + { { 0x4D, 0x10 }, 2 },
> + { { 0x4E, 0x01 }, 2 },
> + { { 0x4F, 0x01 }, 2 },
> + { { 0x50, 0x10 }, 2 },
> + { { 0x51, 0x00 }, 2 },
> + { { 0x52, 0x80 }, 2 },
> + { { 0x53, 0x00 }, 2 },
> + { { 0x56, 0x00 }, 2 },
> + { { 0x54, 0x07 }, 2 },
> + { { 0x58, 0x07 }, 2 },
> + { { 0x55, 0x25 }, 2 },
> + /* Reset XDONB */
> + { { 0x5B, 0x43 }, 2 },
> + { { 0x5C, 0x00 }, 2 },
> + { { 0x5F, 0x73 }, 2 },
> + { { 0x60, 0x73 }, 2 },
> + { { 0x63, 0x22 }, 2 },
> + { { 0x64, 0x00 }, 2 },
> + { { 0x67, 0x08 }, 2 },
> + { { 0x68, 0x04 }, 2 },
> + /* Resolution:1440x2560 */
> + { { 0x72, 0x02 }, 2 },
> + /* mux */
> + { { 0x7A, 0x80 }, 2 },
> + { { 0x7B, 0x91 }, 2 },
> + { { 0x7C, 0xD8 }, 2 },
> + { { 0x7D, 0x60 }, 2 },
> + { { 0x7F, 0x15 }, 2 },
> + { { 0x75, 0x15 }, 2 },
> + /* ABOFF */
> + { { 0xB3, 0xC0 }, 2 },
> + { { 0xB4, 0x00 }, 2 },
> + { { 0xB5, 0x00 }, 2 },
> + /* Source EQ */
> + { { 0x78, 0x00 }, 2 },
> + { { 0x79, 0x00 }, 2 },
> + { { 0x80, 0x00 }, 2 },
> + { { 0x83, 0x00 }, 2 },
> + /* FP BP */
> + { { 0x93, 0x0A }, 2 },
> + { { 0x94, 0x0A }, 2 },
> + /* Inversion Type */
> + { { 0x8A, 0x00 }, 2 },
> + { { 0x9B, 0xFF }, 2 },
> + /* IMGSWAP =1 @PortSwap=1 */
> + { { 0x9D, 0xB0 }, 2 },
> + { { 0x9F, 0x63 }, 2 },
> + { { 0x98, 0x10 }, 2 },
> + /* FRM */
> + { { 0xEC, 0x00 }, 2 },
> + /* CMD1 */
> + { { 0xFF, 0x10 }, 2 },
> + /* VBP+VSA=,VFP = 10H */
> + { { 0x3B, 0x03, 0x0A, 0x0A }, 4 },
> + /* FTE on */
> + { { 0x35, 0x00 }, 2 },
> + /* EN_BK =1(auto black) */
> + { { 0xE5, 0x01 }, 2 },
> + /* CMD mode(10) VDO mode(03) */
> + { { 0xBB, 0x03 }, 2 },
> + /* Non Reload MTP */
> + { { 0xFB, 0x01 }, 2 },
> +};
> +
> +static int truly_dcs_write(struct drm_panel *panel, u32 command)
> +{
> + struct truly_nt35597 *ctx = panel_to_ctx(panel);
> + int i, ret;
> +
> + for (i = 0; i < ARRAY_SIZE(ctx->dsi); i++) {
> + ret = mipi_dsi_dcs_write(ctx->dsi[i],
> + command, NULL, 0);
This can fit on one line
> + if (ret < 0) {
> + DRM_DEV_ERROR(ctx->dev,
> + "cmd 0x%x failed for dsi = %d\n", command,
> + i);
> + }
> + }
> +
> + return ret;
> +}
> +
> +static int truly_dcs_write_buf(struct drm_panel *panel,
> + u32 size, u8 *buf)
> +{
> + struct truly_nt35597 *ctx = panel_to_ctx(panel);
> + int ret = 0;
> + int i;
> +
> + for (i = 0; i < ARRAY_SIZE(ctx->dsi); i++) {
> + ret = mipi_dsi_dcs_write_buffer(ctx->dsi[i],
> + buf,
> + size);
This can fit on one line
> +
> + if (ret < 0) {
> + DRM_DEV_ERROR(ctx->dev,
> + "failed to tx cmd [%d], err: %d\n",
> + i, ret);
> + return ret;
> + }
> + }
> +
> + return ret;
> +}
> +
> +static int truly_35597_power_on(struct truly_nt35597 *ctx)
> +{
> + int ret, i;
> +
> + for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++) {
> + ret = regulator_set_load(ctx->supplies[i].consumer,
> + regulator_enable_loads[i]);
> + if (ret)
> + return ret;
> + }
> +
> + ret = regulator_bulk_enable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
> + if (ret < 0)
> + return ret;
> +
> + /* Reset sequence of truly panel requires
> + * the reset pin to be pulled high for 10ms
> + * followed by a low period of 10ms and then
The highs and lows are backwards in this comment. Your also way inside 80 chars
for this comment. Perhaps it was previously indented a bunch and hasn't been
reflowed? Anyways, it might be more clear if you don't talk about what the pin
is doing, but rather the reset state of the panel:
/*
* Reset sequence of truly panel requires the panel to be out of reset
* for 10ms, followed by being held in reset for 10ms and then out again
*/
> + * pulled high again
> + */
> +
> + gpiod_set_value(ctx->reset_gpio, 0);
> + usleep_range(10000, 20000);
> + gpiod_set_value(ctx->reset_gpio, 1);
> + usleep_range(10000, 20000);
> + gpiod_set_value(ctx->reset_gpio, 0);
> +
> + return 0;
> +}
> +
> +static int truly_nt35597_power_off(struct truly_nt35597 *ctx)
> +{
> + int ret, i;
> +
> + gpiod_set_value(ctx->reset_gpio, 1);
> +
> + for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++) {
> + ret = regulator_set_load(ctx->supplies[i].consumer,
> + regulator_disable_loads[i]);
> + if (ret)
> + return ret;
> + }
> +
> + return regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
> +}
> +
> +static int truly_nt35597_disable(struct drm_panel *panel)
> +{
> + struct truly_nt35597 *ctx = panel_to_ctx(panel);
> + int ret;
> +
> + if (!ctx->enabled)
> + return 0;
> +
> + if (ctx->backlight) {
> + ret = backlight_disable(ctx->backlight);
> + if (ret < 0)
> + DRM_DEV_ERROR(ctx->dev, "backlight disable failed %d\n",
> + ret);
> + }
> +
> + ctx->enabled = false;
> + return 0;
> +}
> +
> +static int truly_nt35597_unprepare(struct drm_panel *panel)
> +{
> + struct truly_nt35597 *ctx = panel_to_ctx(panel);
> + int ret = 0;
> +
> + if (!ctx->prepared)
> + return 0;
> +
> + ctx->dsi[0]->mode_flags = 0;
> + ctx->dsi[1]->mode_flags = 0;
> +
> + ret = truly_dcs_write(panel, MIPI_DCS_SET_DISPLAY_OFF);
> + if (ret < 0) {
> + DRM_DEV_ERROR(ctx->dev,
> + "set_display_off cmd failed ret = %d\n",
> + ret);
> + }
> +
> + /* 120ms delay required here as per DCS spec */
> + msleep(120);
> +
> + ret = truly_dcs_write(panel, MIPI_DCS_ENTER_SLEEP_MODE);
> + if (ret < 0) {
> + DRM_DEV_ERROR(ctx->dev,
> + "enter_sleep cmd failed ret = %d\n",
> + ret);
> + }
> +
> + ret = truly_nt35597_power_off(ctx);
> + if (ret < 0)
> + DRM_DEV_ERROR(ctx->dev,
> + "truly_nt35597_power_off failed ret = %d\n",
> + ret);
> +
> + ctx->prepared = false;
> + return ret;
> +}
> +
> +static int truly_nt35597_prepare(struct drm_panel *panel)
> +{
> + struct truly_nt35597 *ctx = panel_to_ctx(panel);
> + int ret;
> + int i;
> + struct cmd_set *panel_on_cmds;
> + const struct nt35597_config *config;
> + u32 num_cmds;
> +
> + if (ctx->prepared)
> + return 0;
> +
> + ret = truly_35597_power_on(ctx);
> + if (ret < 0)
> + return ret;
> +
> + ctx->dsi[0]->mode_flags |= MIPI_DSI_MODE_LPM;
> + ctx->dsi[1]->mode_flags |= MIPI_DSI_MODE_LPM;
> +
> + config = ctx->config;
> + panel_on_cmds = (struct cmd_set *)config->panel_on_cmds;
> + num_cmds = config->num_on_cmds;
> +
> + for (i = 0; i < num_cmds; i++) {
> + ret = truly_dcs_write_buf(panel,
> + panel_on_cmds[i].size,
> + panel_on_cmds[i].commands);
> + if (ret < 0) {
> + DRM_DEV_ERROR(ctx->dev,
> + "cmd set tx failed i = %d ret = %d\n",
> + i, ret);
> + goto power_off;
> + }
> + }
> +
> + /* As per DSI spec need to wait for 120ms
> + * after sending the exit sleep DCS command
> + */
This comment seems like it's in the wrong place. Also, multi-line comments are
formatted as follows:
/*
* multi-line
* comment
*/
If you like to save space, like me, you could probably fit this on 1 line like:
/* Per DSI spec, wait 120ms after sending the exit sleep DCS command */
> +
> + ret = truly_dcs_write(panel, MIPI_DCS_EXIT_SLEEP_MODE);
> + if (ret < 0) {
> + DRM_DEV_ERROR(ctx->dev,
> + "exit_sleep_mode cmd failed ret = %d\n",
> + ret);
> + goto power_off;
> + }
> +
> + msleep(120);
> +
> + ret = truly_dcs_write(panel, MIPI_DCS_SET_DISPLAY_ON);
> + if (ret < 0) {
> + DRM_DEV_ERROR(ctx->dev,
> + "set_display_on cmd failed ret = %d\n",
> + ret);
> + goto power_off;
> + }
> +
> + /* Adding 120ms delay before the start of
> + * pixel stream to the panel after sending
> + * the set_display_on DCS command
> + */
> +
> + msleep(120);
> +
> + ctx->prepared = true;
> +
> + return 0;
> +
> +power_off:
> + gpiod_set_value(ctx->reset_gpio, 1);
> +
> + for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++)
> + regulator_set_load(ctx->supplies[i].consumer,
> + regulator_disable_loads[i]);
> +
> + ret = regulator_bulk_disable(ARRAY_SIZE(ctx->supplies),
> + ctx->supplies);
This seems like a straight copy of truly_nt35597_power_off(), just call that
function.
> + DRM_DEV_ERROR(ctx->dev,
> + "regulator disable failed, %d\n", ret);
This fits on one line.
> +
> + return ret;
> +}
> +
> +static int truly_nt35597_enable(struct drm_panel *panel)
> +{
> + struct truly_nt35597 *ctx = panel_to_ctx(panel);
> + int ret;
> +
> + if (ctx->enabled)
> + return 0;
> +
> + if (ctx->backlight) {
> + ret = backlight_enable(ctx->backlight);
> + if (ret < 0)
> + DRM_DEV_ERROR(ctx->dev, "backlight enable failed %d\n",
> + ret);
> + }
> +
> + ctx->enabled = true;
> +
> + return 0;
> +}
> +
> +static int truly_nt35597_get_modes(struct drm_panel *panel)
> +{
> + struct drm_connector *connector = panel->connector;
> + struct truly_nt35597 *ctx = panel_to_ctx(panel);
> + struct drm_display_mode *mode;
> + const struct nt35597_config *config;
> +
> + config = ctx->config;
> + mode = drm_mode_create(connector->dev);
> + if (!mode) {
> + DRM_DEV_ERROR(ctx->dev,
> + "failed to create a new display mode\n");
> + return 0;
> + }
> +
> + connector->display_info.width_mm = config->width_mm;
> + connector->display_info.height_mm = config->height_mm;
> + drm_mode_copy(mode, config->dm);
> + mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
> + drm_mode_probed_add(connector, mode);
> +
> + return 1;
> +}
> +
> +static const struct drm_panel_funcs truly_nt35597_drm_funcs = {
> + .disable = truly_nt35597_disable,
> + .unprepare = truly_nt35597_unprepare,
> + .prepare = truly_nt35597_prepare,
> + .enable = truly_nt35597_enable,
> + .get_modes = truly_nt35597_get_modes,
> +};
> +
> +static int truly_nt35597_panel_add(struct truly_nt35597 *ctx)
> +{
> + struct device *dev = ctx->dev;
> + int ret, i;
> + const struct nt35597_config *config;
> +
> + config = ctx->config;
> + for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++)
> + ctx->supplies[i].supply = regulator_names[i];
> +
> + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ctx->supplies),
> + ctx->supplies);
> + if (ret < 0)
> + return ret;
> +
> + ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
> + if (IS_ERR(ctx->reset_gpio)) {
> + DRM_DEV_ERROR(dev, "cannot get reset gpio %ld\n",
> + PTR_ERR(ctx->reset_gpio));
> + return PTR_ERR(ctx->reset_gpio);
> + }
> +
> + ctx->mode_gpio = devm_gpiod_get(dev, "mode", GPIOD_OUT_LOW);
> + if (IS_ERR(ctx->mode_gpio)) {
> + DRM_DEV_ERROR(dev, "cannot get mode gpio %ld\n",
> + PTR_ERR(ctx->mode_gpio));
> + return PTR_ERR(ctx->mode_gpio);
> + }
> +
> + /* dual port */
> + gpiod_set_value(ctx->mode_gpio, 0);
> +
> + drm_panel_init(&ctx->panel);
> + ctx->panel.dev = dev;
> + ctx->panel.funcs = &truly_nt35597_drm_funcs;
> + drm_panel_add(&ctx->panel);
> +
> + return 0;
> +}
> +
> +static const struct drm_display_mode qcom_sdm845_mtp_2k_mode = {
> + .name = "1440x2560",
> + .clock = 268316,
> + .hdisplay = 1440,
> + .hsync_start = 1440 + 200,
> + .hsync_end = 1440 + 200 + 32,
> + .htotal = 1440 + 200 + 32 + 64,
> + .vdisplay = 2560,
> + .vsync_start = 2560 + 8,
> + .vsync_end = 2560 + 8 + 1,
> + .vtotal = 2560 + 8 + 1 + 7,
> + .vrefresh = 60,
> + .flags = 0,
> +};
> +
> +static const struct nt35597_config nt35597_dir = {
> + .width_mm = 74,
> + .height_mm = 131,
> + .panel_name = "qcom_sdm845_mtp_2k_panel",
> + .dm = &qcom_sdm845_mtp_2k_mode,
> + .panel_on_cmds = qcom_2k_panel_magic_cmds,
> + .num_on_cmds = ARRAY_SIZE(qcom_2k_panel_magic_cmds),
> +};
> +
> +static int truly_nt35597_probe(struct mipi_dsi_device *dsi)
> +{
> + struct device *dev = &dsi->dev;
> + struct truly_nt35597 *ctx;
> + struct mipi_dsi_device *dsi1_device;
> + struct device_node *dsi1;
> + struct mipi_dsi_host *dsi1_host;
> + struct mipi_dsi_device *dsi_dev;
> + int ret = 0;
> + int i;
> +
> + const struct mipi_dsi_device_info info = {
> + .type = "trulynt35597",
> + .channel = 0,
> + .node = NULL,
> + };
> +
> + ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
> +
> + if (!ctx)
> + return -ENOMEM;
> +
> + /* This device represents itself as one with
> + * two input ports which are fed by the output
> + * ports of the two DSI controllers . The DSI0
> + * is the master controller and has most of the
> + * panel related info in its child node.
> + */
> +
> + ctx->config = of_device_get_match_data(dev);
> +
> + if (!ctx->config) {
> + dev_err(dev, "missing device configuration\n");
> + return -ENODEV;
> + }
> +
> + dsi1 = of_graph_get_remote_node(dsi->dev.of_node, 1, -1);
> + if (!dsi1) {
> + DRM_DEV_ERROR(dev,
> + "failed to get remote node for dsi1_device\n");
> + ret = -ENODEV;
> + goto err_get_remote;
Just return directly.
> + }
> +
> + dsi1_host = of_find_mipi_dsi_host_by_node(dsi1);
Move that of_node_put(dsi1) here.
> + if (!dsi1_host) {
> + DRM_DEV_ERROR(dev, "failed to find dsi host\n");
> + ret = -EPROBE_DEFER;
> + goto err_host;
Now you can return directly from here
> + }
> +
> + of_node_put(dsi1);
> +
> + /* register the second DSI device */
> + dsi1_device = mipi_dsi_device_register_full(dsi1_host, &info);
> + if (IS_ERR(dsi1_device)) {
> + DRM_DEV_ERROR(dev, "failed to create dsi device\n");
> + ret = PTR_ERR(dsi);
> + goto err_dsi_device;
And here
> + }
> +
> + mipi_dsi_set_drvdata(dsi, ctx);
> +
> + ctx->dev = dev;
> + ctx->dsi[0] = dsi;
> + ctx->dsi[1] = dsi1_device;
> +
> + ret = truly_nt35597_panel_add(ctx);
> + if (ret) {
> + DRM_DEV_ERROR(dev, "failed to add panel\n");
> + goto err_panel_add;
> + }
> +
> + for (i = 0; i < ARRAY_SIZE(ctx->dsi); i++) {
> + dsi_dev = ctx->dsi[i];
> + dsi_dev->lanes = 4;
> + dsi_dev->format = MIPI_DSI_FMT_RGB888;
> + dsi_dev->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_LPM |
> + MIPI_DSI_CLOCK_NON_CONTINUOUS;
> + ret = mipi_dsi_attach(dsi_dev);
> + if (ret < 0) {
> + DRM_DEV_ERROR(dev,
> + "dsi attach failed i = %d\n", i);
> + goto err_dsi_attach;
> + }
> + }
> +
> + return 0;
> +
> +err_dsi_attach:
> + drm_panel_remove(&ctx->panel);
> +err_panel_add:
> + mipi_dsi_device_unregister(dsi1_device);
> +err_dsi_device:
> +err_host:
> + of_node_put(dsi1);
> +err_get_remote:
> + return ret;
> +}
> +
> +static int truly_nt35597_remove(struct mipi_dsi_device *dsi)
> +{
> + struct truly_nt35597 *ctx = mipi_dsi_get_drvdata(dsi);
> +
> + if (ctx->dsi[0])
> + mipi_dsi_detach(ctx->dsi[0]);
> + if (ctx->dsi[1]) {
> + mipi_dsi_detach(ctx->dsi[1]);
> + mipi_dsi_device_unregister(ctx->dsi[1]);
> + }
> +
> + drm_panel_remove(&ctx->panel);
> + return 0;
> +}
> +
> +static const struct of_device_id truly_nt35597_of_match[] = {
> + { .compatible = "truly,nt35597-2K-display",
> + .data = &nt35597_dir,
> + },
> +
> + { }
> +};
> +MODULE_DEVICE_TABLE(of, truly_nt35597_of_match);
> +
> +static struct mipi_dsi_driver truly_nt35597_driver = {
> + .driver = {
> + .name = "panel_truly_nt35597",
> + .of_match_table = truly_nt35597_of_match,
> + },
> + .probe = truly_nt35597_probe,
> + .remove = truly_nt35597_remove,
> +};
> +module_mipi_dsi_driver(truly_nt35597_driver);
> +
> +MODULE_DESCRIPTION("Truly NT35597 DSI Panel Driver");
> +MODULE_LICENSE("GPL v2");
> --
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> a Linux Foundation Collaborative Project
>
> _______________________________________________
> dri-devel mailing list
> dri-devel at lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/dri-devel
--
Sean Paul, Software Engineer, Google / Chromium OS
More information about the dri-devel
mailing list