[PATCH v8 1/2] drm/panel: Add support for Truly NT35597 panel driver
Abhinav Kumar
abhinavk at codeaurora.org
Thu Sep 27 17:25:33 UTC 2018
Hi Thierry
Thanks for the comments.
I will fix these in v9.
Thanks
Abhinav
On 2018-09-27 05:20, Thierry Reding wrote:
> On Thu, Sep 20, 2018 at 03:52:36PM -0700, Abhinav Kumar wrote:
>> From: "abhinavk at codeaurora.org" <abhinavk at codeaurora.org>
>>
>> Add support for Truly NT35597 panel driver used
>> in MSM reference platforms.
>>
>> This panel driver supports both single DSI and dual DSI
>> modes.
>>
>> However, this patch series adds support only for
>> dual DSI mode.
>
> Your lines are very short here. It's usually a good idea to keep the
> subject line short, but there's no need to wrap this early in the rest
> of the commit message. It's customary to use up to 72 characters.
>
>>
>> Changes in v8:
>> - Remove video mode config and headers
>> - Remove unused macros
>> - Try to avoid multi-lines wherever possible
>> - Fix comments locations and make it concise
>> - Fix return points in probe function
>>
>> Signed-off-by: Archit Taneja <architt at codeaurora.org>
>> Signed-off-by: Abhinav Kumar <abhinavk at codeaurora.org>
>> ---
>> drivers/gpu/drm/panel/Kconfig | 7 +
>> drivers/gpu/drm/panel/Makefile | 1 +
>> drivers/gpu/drm/panel/panel-truly-nt35597.c | 676
>> ++++++++++++++++++++++++++++
>> 3 files changed, 684 insertions(+)
>> create mode 100644 drivers/gpu/drm/panel/panel-truly-nt35597.c
>>
>> diff --git a/drivers/gpu/drm/panel/Kconfig
>> b/drivers/gpu/drm/panel/Kconfig
>> index 6020c30..073ffa0 100644
>> --- a/drivers/gpu/drm/panel/Kconfig
>> +++ b/drivers/gpu/drm/panel/Kconfig
>> @@ -186,4 +186,11 @@ config DRM_PANEL_SITRONIX_ST7789V
>> Say Y here if you want to enable support for the Sitronix
>> ST7789V controller for 240x320 LCD panels
>>
>> +config DRM_PANEL_TRULY_NT35597_WQXGA
>> + tristate "Truly WQXGA"
>> + depends on OF
>> + depends on DRM_MIPI_DSI
>> + help
>> + Say Y here if you want to enable support for Truly NT35597 WQXGA
>> Dual DSI
>> + Video Mode panel
>> endmenu
>> diff --git a/drivers/gpu/drm/panel/Makefile
>> b/drivers/gpu/drm/panel/Makefile
>> index 5ccaaa9..80fd19f 100644
>> --- a/drivers/gpu/drm/panel/Makefile
>> +++ b/drivers/gpu/drm/panel/Makefile
>> @@ -19,3 +19,4 @@ obj-$(CONFIG_DRM_PANEL_SEIKO_43WVF1G) +=
>> panel-seiko-43wvf1g.o
>> obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) +=
>> panel-sharp-lq101r1sx01.o
>> obj-$(CONFIG_DRM_PANEL_SHARP_LS043T1LE01) +=
>> panel-sharp-ls043t1le01.o
>> obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o
>> +obj-$(CONFIG_DRM_PANEL_TRULY_NT35597_WQXGA) += panel-truly-nt35597.o
>> diff --git a/drivers/gpu/drm/panel/panel-truly-nt35597.c
>> b/drivers/gpu/drm/panel/panel-truly-nt35597.c
>> new file mode 100644
>> index 0000000..c9e09e2
>> --- /dev/null
>> +++ b/drivers/gpu/drm/panel/panel-truly-nt35597.c
>> @@ -0,0 +1,676 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Copyright (c) 2018, The Linux Foundation. All rights reserved.
>> + */
>> +
>> +#include <linux/gpio/consumer.h>
>> +#include <linux/of_graph.h>
>> +#include <linux/regulator/consumer.h>
>> +#include <linux/pinctrl/consumer.h>
>> +#include <linux/of_device.h>
>> +
>> +#include <video/mipi_display.h>
>> +
>> +#include <drm/drmP.h>
>> +#include <drm/drm_panel.h>
>> +#include <drm/drm_mipi_dsi.h>
>
> The headers should be sorted alphabetically.
>
>> +
>> +static const char * const regulator_names[] = {
>> + "vdda",
>> + "vdispp",
>> + "vdispn",
>> +};
>> +
>> +static unsigned long const regulator_enable_loads[] = {
>> + 62000,
>> + 100000,
>> + 100000,
>> +};
>> +
>> +static unsigned long const regulator_disable_loads[] = {
>> + 80,
>> + 100,
>> + 100,
>> +};
>> +
>> +struct nt35597_config {
>> + u32 width_mm;
>> + u32 height_mm;
>> + const char *panel_name;
>> + const void *panel_on_cmds;
>
> Why void *? You define the correct data structure a few lines further
> down, so you might as well just move that definition up and use the
> proper data structure here. Then there'd be no need to cast this to
> struct cmd_set * later on when you use it.
>
>> + u32 num_on_cmds;
>> + const struct drm_display_mode *dm;
>> +};
>> +
>> +struct truly_nt35597 {
>> + struct device *dev;
>> + struct drm_panel panel;
>> +
>> + struct regulator_bulk_data supplies[ARRAY_SIZE(regulator_names)];
>> +
>> + struct gpio_desc *reset_gpio;
>> + struct gpio_desc *mode_gpio;
>> +
>> + struct backlight_device *backlight;
>> +
>> + struct mipi_dsi_device *dsi[2];
>> +
>> + const struct nt35597_config *config;
>> + bool prepared;
>> + bool enabled;
>> +};
>> +
>> +static inline struct truly_nt35597 *panel_to_ctx(struct drm_panel
>> *panel)
>> +{
>> + return container_of(panel, struct truly_nt35597, panel);
>> +}
>> +
>> +struct cmd_set {
>> + u8 commands[4];
>> + u8 size;
>> +};
>> +
>> +static struct cmd_set qcom_2k_panel_magic_cmds[] = {
>
> static const?
>
>> + /* CMD2_P0 */
>> + { { 0xff, 0x20 }, 2 },
>> + { { 0xfb, 0x01 }, 2 },
>> + { { 0x00, 0x01 }, 2 },
>> + { { 0x01, 0x55 }, 2 },
>> + { { 0x02, 0x45 }, 2 },
>> + { { 0x05, 0x40 }, 2 },
>> + { { 0x06, 0x19 }, 2 },
>> + { { 0x07, 0x1e }, 2 },
>> + { { 0x0b, 0x73 }, 2 },
>> + { { 0x0c, 0x73 }, 2 },
>> + { { 0x0e, 0xb0 }, 2 },
>> + { { 0x0f, 0xae }, 2 },
>> + { { 0x11, 0xb8 }, 2 },
>> + { { 0x13, 0x00 }, 2 },
>> + { { 0x58, 0x80 }, 2 },
>> + { { 0x59, 0x01 }, 2 },
>> + { { 0x5a, 0x00 }, 2 },
>> + { { 0x5b, 0x01 }, 2 },
>> + { { 0x5c, 0x80 }, 2 },
>> + { { 0x5d, 0x81 }, 2 },
>> + { { 0x5e, 0x00 }, 2 },
>> + { { 0x5f, 0x01 }, 2 },
>> + { { 0x72, 0x11 }, 2 },
>> + { { 0x68, 0x03 }, 2 },
>> + /* CMD2_P4 */
>> + { { 0xFF, 0x24 }, 2 },
>> + { { 0xFB, 0x01 }, 2 },
>> + { { 0x00, 0x1C }, 2 },
>> + { { 0x01, 0x0B }, 2 },
>> + { { 0x02, 0x0C }, 2 },
>> + { { 0x03, 0x01 }, 2 },
>> + { { 0x04, 0x0F }, 2 },
>> + { { 0x05, 0x10 }, 2 },
>> + { { 0x06, 0x10 }, 2 },
>> + { { 0x07, 0x10 }, 2 },
>> + { { 0x08, 0x89 }, 2 },
>> + { { 0x09, 0x8A }, 2 },
>> + { { 0x0A, 0x13 }, 2 },
>> + { { 0x0B, 0x13 }, 2 },
>> + { { 0x0C, 0x15 }, 2 },
>> + { { 0x0D, 0x15 }, 2 },
>> + { { 0x0E, 0x17 }, 2 },
>> + { { 0x0F, 0x17 }, 2 },
>> + { { 0x10, 0x1C }, 2 },
>> + { { 0x11, 0x0B }, 2 },
>> + { { 0x12, 0x0C }, 2 },
>> + { { 0x13, 0x01 }, 2 },
>> + { { 0x14, 0x0F }, 2 },
>> + { { 0x15, 0x10 }, 2 },
>> + { { 0x16, 0x10 }, 2 },
>> + { { 0x17, 0x10 }, 2 },
>> + { { 0x18, 0x89 }, 2 },
>> + { { 0x19, 0x8A }, 2 },
>> + { { 0x1A, 0x13 }, 2 },
>> + { { 0x1B, 0x13 }, 2 },
>> + { { 0x1C, 0x15 }, 2 },
>> + { { 0x1D, 0x15 }, 2 },
>> + { { 0x1E, 0x17 }, 2 },
>> + { { 0x1F, 0x17 }, 2 },
>> + /* STV */
>> + { { 0x20, 0x40 }, 2 },
>> + { { 0x21, 0x01 }, 2 },
>> + { { 0x22, 0x00 }, 2 },
>> + { { 0x23, 0x40 }, 2 },
>> + { { 0x24, 0x40 }, 2 },
>> + { { 0x25, 0x6D }, 2 },
>> + { { 0x26, 0x40 }, 2 },
>> + { { 0x27, 0x40 }, 2 },
>> + /* Vend */
>> + { { 0xE0, 0x00 }, 2 },
>> + { { 0xDC, 0x21 }, 2 },
>> + { { 0xDD, 0x22 }, 2 },
>> + { { 0xDE, 0x07 }, 2 },
>> + { { 0xDF, 0x07 }, 2 },
>> + { { 0xE3, 0x6D }, 2 },
>> + { { 0xE1, 0x07 }, 2 },
>> + { { 0xE2, 0x07 }, 2 },
>> + /* UD */
>> + { { 0x29, 0xD8 }, 2 },
>> + { { 0x2A, 0x2A }, 2 },
>> + /* CLK */
>> + { { 0x4B, 0x03 }, 2 },
>> + { { 0x4C, 0x11 }, 2 },
>> + { { 0x4D, 0x10 }, 2 },
>> + { { 0x4E, 0x01 }, 2 },
>> + { { 0x4F, 0x01 }, 2 },
>> + { { 0x50, 0x10 }, 2 },
>> + { { 0x51, 0x00 }, 2 },
>> + { { 0x52, 0x80 }, 2 },
>> + { { 0x53, 0x00 }, 2 },
>> + { { 0x56, 0x00 }, 2 },
>> + { { 0x54, 0x07 }, 2 },
>> + { { 0x58, 0x07 }, 2 },
>> + { { 0x55, 0x25 }, 2 },
>> + /* Reset XDONB */
>> + { { 0x5B, 0x43 }, 2 },
>> + { { 0x5C, 0x00 }, 2 },
>> + { { 0x5F, 0x73 }, 2 },
>> + { { 0x60, 0x73 }, 2 },
>> + { { 0x63, 0x22 }, 2 },
>> + { { 0x64, 0x00 }, 2 },
>> + { { 0x67, 0x08 }, 2 },
>> + { { 0x68, 0x04 }, 2 },
>> + /* Resolution:1440x2560 */
>> + { { 0x72, 0x02 }, 2 },
>> + /* mux */
>> + { { 0x7A, 0x80 }, 2 },
>> + { { 0x7B, 0x91 }, 2 },
>> + { { 0x7C, 0xD8 }, 2 },
>> + { { 0x7D, 0x60 }, 2 },
>> + { { 0x7F, 0x15 }, 2 },
>> + { { 0x75, 0x15 }, 2 },
>> + /* ABOFF */
>> + { { 0xB3, 0xC0 }, 2 },
>> + { { 0xB4, 0x00 }, 2 },
>> + { { 0xB5, 0x00 }, 2 },
>> + /* Source EQ */
>> + { { 0x78, 0x00 }, 2 },
>> + { { 0x79, 0x00 }, 2 },
>> + { { 0x80, 0x00 }, 2 },
>> + { { 0x83, 0x00 }, 2 },
>> + /* FP BP */
>> + { { 0x93, 0x0A }, 2 },
>> + { { 0x94, 0x0A }, 2 },
>> + /* Inversion Type */
>> + { { 0x8A, 0x00 }, 2 },
>> + { { 0x9B, 0xFF }, 2 },
>> + /* IMGSWAP =1 @PortSwap=1 */
>> + { { 0x9D, 0xB0 }, 2 },
>> + { { 0x9F, 0x63 }, 2 },
>> + { { 0x98, 0x10 }, 2 },
>> + /* FRM */
>> + { { 0xEC, 0x00 }, 2 },
>> + /* CMD1 */
>> + { { 0xFF, 0x10 }, 2 },
>> + /* VBP+VSA=,VFP = 10H */
>> + { { 0x3B, 0x03, 0x0A, 0x0A }, 4 },
>> + /* FTE on */
>> + { { 0x35, 0x00 }, 2 },
>> + /* EN_BK =1(auto black) */
>> + { { 0xE5, 0x01 }, 2 },
>> + /* CMD mode(10) VDO mode(03) */
>> + { { 0xBB, 0x03 }, 2 },
>> + /* Non Reload MTP */
>> + { { 0xFB, 0x01 }, 2 },
>> +};
>> +
>> +static int truly_dcs_write(struct drm_panel *panel, u32 command)
>> +{
>> + struct truly_nt35597 *ctx = panel_to_ctx(panel);
>> + int i, ret;
>> +
>> + for (i = 0; i < ARRAY_SIZE(ctx->dsi); i++) {
>> + ret = mipi_dsi_dcs_write(ctx->dsi[i], command, NULL, 0);
>> + if (ret < 0) {
>> + DRM_DEV_ERROR(ctx->dev,
>> + "cmd 0x%x failed for dsi = %d\n",
>> + command, i);
>> + }
>> + }
>> +
>> + return ret;
>> +}
>> +
>> +static int truly_dcs_write_buf(struct drm_panel *panel,
>> + u32 size, u8 *buf)
>> +{
>> + struct truly_nt35597 *ctx = panel_to_ctx(panel);
>> + int ret = 0;
>> + int i;
>> +
>> + for (i = 0; i < ARRAY_SIZE(ctx->dsi); i++) {
>> + ret = mipi_dsi_dcs_write_buffer(ctx->dsi[i], buf, size);
>> + if (ret < 0) {
>> + DRM_DEV_ERROR(ctx->dev,
>> + "failed to tx cmd [%d], err: %d\n", i, ret);
>> + return ret;
>> + }
>> + }
>> +
>> + return ret;
>> +}
>> +
>> +static int truly_35597_power_on(struct truly_nt35597 *ctx)
>> +{
>> + int ret, i;
>> +
>> + for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++) {
>> + ret = regulator_set_load(ctx->supplies[i].consumer,
>> + regulator_enable_loads[i]);
>> + if (ret)
>> + return ret;
>> + }
>> +
>> + ret = regulator_bulk_enable(ARRAY_SIZE(ctx->supplies),
>> ctx->supplies);
>> + if (ret < 0)
>> + return ret;
>> +
>> + /*
>> + * Reset sequence of truly panel requires the panel to be
>> + * out of reset for 10ms, followed by being held in reset
>> + * for 10ms and then out again
>> + */
>> + gpiod_set_value(ctx->reset_gpio, 0);
>> + usleep_range(10000, 20000);
>> + gpiod_set_value(ctx->reset_gpio, 1);
>> + usleep_range(10000, 20000);
>> + gpiod_set_value(ctx->reset_gpio, 0);
>> +
>> + return 0;
>> +}
>> +
>> +static int truly_nt35597_power_off(struct truly_nt35597 *ctx)
>> +{
>> + int ret = 0;
>> + int i;
>> +
>> + gpiod_set_value(ctx->reset_gpio, 1);
>> +
>> + for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++) {
>> + ret = regulator_set_load(ctx->supplies[i].consumer,
>> + regulator_disable_loads[i]);
>> + if (ret) {
>> + DRM_DEV_ERROR(ctx->dev,
>> + "regulator_set_load failed %d\n", ret);
>> + return ret;
>> + }
>> + }
>> +
>> + ret = regulator_bulk_disable(ARRAY_SIZE(ctx->supplies),
>> ctx->supplies);
>> + if (ret) {
>> + DRM_DEV_ERROR(ctx->dev,
>> + "regulator_bulk_disable failed %d\n", ret);
>> + }
>> + return ret;
>> +}
>> +
>> +static int truly_nt35597_disable(struct drm_panel *panel)
>> +{
>> + struct truly_nt35597 *ctx = panel_to_ctx(panel);
>> + int ret;
>> +
>> + if (!ctx->enabled)
>> + return 0;
>> +
>> + if (ctx->backlight) {
>> + ret = backlight_disable(ctx->backlight);
>> + if (ret < 0)
>> + DRM_DEV_ERROR(ctx->dev, "backlight disable failed %d\n",
>> + ret);
>> + }
>> +
>> + ctx->enabled = false;
>> + return 0;
>> +}
>> +
>> +static int truly_nt35597_unprepare(struct drm_panel *panel)
>> +{
>> + struct truly_nt35597 *ctx = panel_to_ctx(panel);
>> + int ret = 0;
>> +
>> + if (!ctx->prepared)
>> + return 0;
>> +
>> + ctx->dsi[0]->mode_flags = 0;
>> + ctx->dsi[1]->mode_flags = 0;
>> +
>> + ret = truly_dcs_write(panel, MIPI_DCS_SET_DISPLAY_OFF);
>> + if (ret < 0) {
>> + DRM_DEV_ERROR(ctx->dev,
>> + "set_display_off cmd failed ret = %d\n",
>> + ret);
>> + }
>> +
>> + /* 120ms delay required here as per DCS spec */
>> + msleep(120);
>> +
>> + ret = truly_dcs_write(panel, MIPI_DCS_ENTER_SLEEP_MODE);
>> + if (ret < 0) {
>> + DRM_DEV_ERROR(ctx->dev,
>> + "enter_sleep cmd failed ret = %d\n", ret);
>> + }
>> +
>> + ret = truly_nt35597_power_off(ctx);
>> + if (ret < 0)
>> + DRM_DEV_ERROR(ctx->dev, "power_off failed ret = %d\n", ret);
>> +
>> + ctx->prepared = false;
>> + return ret;
>> +}
>> +
>> +static int truly_nt35597_prepare(struct drm_panel *panel)
>> +{
>> + struct truly_nt35597 *ctx = panel_to_ctx(panel);
>> + int ret;
>> + int i;
>> + struct cmd_set *panel_on_cmds;
>> + const struct nt35597_config *config;
>> + u32 num_cmds;
>> +
>> + if (ctx->prepared)
>> + return 0;
>> +
>> + ret = truly_35597_power_on(ctx);
>> + if (ret < 0)
>> + return ret;
>> +
>> + ctx->dsi[0]->mode_flags |= MIPI_DSI_MODE_LPM;
>> + ctx->dsi[1]->mode_flags |= MIPI_DSI_MODE_LPM;
>> +
>> + config = ctx->config;
>> + panel_on_cmds = (struct cmd_set *)config->panel_on_cmds;
>> + num_cmds = config->num_on_cmds;
>> +
>> + for (i = 0; i < num_cmds; i++) {
>> + ret = truly_dcs_write_buf(panel,
>> + panel_on_cmds[i].size,
>> + panel_on_cmds[i].commands);
>> + if (ret < 0) {
>> + DRM_DEV_ERROR(ctx->dev,
>> + "cmd set tx failed i = %d ret = %d\n",
>> + i, ret);
>> + goto power_off;
>> + }
>> + }
>> +
>> + ret = truly_dcs_write(panel, MIPI_DCS_EXIT_SLEEP_MODE);
>> + if (ret < 0) {
>> + DRM_DEV_ERROR(ctx->dev,
>> + "exit_sleep_mode cmd failed ret = %d\n",
>> + ret);
>> + goto power_off;
>> + }
>> +
>> + /* Per DSI spec wait 120ms after sending exit sleep DCS command */
>> + msleep(120);
>> +
>> + ret = truly_dcs_write(panel, MIPI_DCS_SET_DISPLAY_ON);
>> + if (ret < 0) {
>> + DRM_DEV_ERROR(ctx->dev,
>> + "set_display_on cmd failed ret = %d\n", ret);
>> + goto power_off;
>> + }
>> +
>> + /* Per DSI spec wait 120ms after sending set_display_on DCS command
>> */
>> + msleep(120);
>> +
>> + ctx->prepared = true;
>> +
>> + return 0;
>> +
>> +power_off:
>> + if (truly_nt35597_power_off(ctx))
>> + DRM_DEV_ERROR(ctx->dev, "power_off failed\n");
>> + return ret;
>> +}
>> +
>> +static int truly_nt35597_enable(struct drm_panel *panel)
>> +{
>> + struct truly_nt35597 *ctx = panel_to_ctx(panel);
>> + int ret;
>> +
>> + if (ctx->enabled)
>> + return 0;
>> +
>> + if (ctx->backlight) {
>> + ret = backlight_enable(ctx->backlight);
>> + if (ret < 0)
>> + DRM_DEV_ERROR(ctx->dev, "backlight enable failed %d\n",
>> + ret);
>> + }
>> +
>> + ctx->enabled = true;
>> +
>> + return 0;
>> +}
>> +
>> +static int truly_nt35597_get_modes(struct drm_panel *panel)
>> +{
>> + struct drm_connector *connector = panel->connector;
>> + struct truly_nt35597 *ctx = panel_to_ctx(panel);
>> + struct drm_display_mode *mode;
>> + const struct nt35597_config *config;
>> +
>> + config = ctx->config;
>> + mode = drm_mode_create(connector->dev);
>> + if (!mode) {
>> + DRM_DEV_ERROR(ctx->dev,
>> + "failed to create a new display mode\n");
>> + return 0;
>> + }
>> +
>> + connector->display_info.width_mm = config->width_mm;
>> + connector->display_info.height_mm = config->height_mm;
>> + drm_mode_copy(mode, config->dm);
>> + mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
>> + drm_mode_probed_add(connector, mode);
>> +
>> + return 1;
>> +}
>> +
>> +static const struct drm_panel_funcs truly_nt35597_drm_funcs = {
>> + .disable = truly_nt35597_disable,
>> + .unprepare = truly_nt35597_unprepare,
>> + .prepare = truly_nt35597_prepare,
>> + .enable = truly_nt35597_enable,
>> + .get_modes = truly_nt35597_get_modes,
>> +};
>> +
>> +static int truly_nt35597_panel_add(struct truly_nt35597 *ctx)
>> +{
>> + struct device *dev = ctx->dev;
>> + int ret, i;
>> + const struct nt35597_config *config;
>> +
>> + config = ctx->config;
>> + for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++)
>> + ctx->supplies[i].supply = regulator_names[i];
>> +
>> + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ctx->supplies),
>> + ctx->supplies);
>> + if (ret < 0)
>> + return ret;
>> +
>> + ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
>> + if (IS_ERR(ctx->reset_gpio)) {
>> + DRM_DEV_ERROR(dev, "cannot get reset gpio %ld\n",
>> + PTR_ERR(ctx->reset_gpio));
>> + return PTR_ERR(ctx->reset_gpio);
>> + }
>> +
>> + ctx->mode_gpio = devm_gpiod_get(dev, "mode", GPIOD_OUT_LOW);
>> + if (IS_ERR(ctx->mode_gpio)) {
>> + DRM_DEV_ERROR(dev, "cannot get mode gpio %ld\n",
>> + PTR_ERR(ctx->mode_gpio));
>> + return PTR_ERR(ctx->mode_gpio);
>> + }
>> +
>> + /* dual port */
>> + gpiod_set_value(ctx->mode_gpio, 0);
>> +
>> + drm_panel_init(&ctx->panel);
>> + ctx->panel.dev = dev;
>> + ctx->panel.funcs = &truly_nt35597_drm_funcs;
>> + drm_panel_add(&ctx->panel);
>> +
>> + return 0;
>> +}
>> +
>> +static const struct drm_display_mode qcom_sdm845_mtp_2k_mode = {
>> + .name = "1440x2560",
>> + .clock = 268316,
>> + .hdisplay = 1440,
>> + .hsync_start = 1440 + 200,
>> + .hsync_end = 1440 + 200 + 32,
>> + .htotal = 1440 + 200 + 32 + 64,
>> + .vdisplay = 2560,
>> + .vsync_start = 2560 + 8,
>> + .vsync_end = 2560 + 8 + 1,
>> + .vtotal = 2560 + 8 + 1 + 7,
>> + .vrefresh = 60,
>> + .flags = 0,
>> +};
>> +
>> +static const struct nt35597_config nt35597_dir = {
>> + .width_mm = 74,
>> + .height_mm = 131,
>> + .panel_name = "qcom_sdm845_mtp_2k_panel",
>> + .dm = &qcom_sdm845_mtp_2k_mode,
>> + .panel_on_cmds = qcom_2k_panel_magic_cmds,
>> + .num_on_cmds = ARRAY_SIZE(qcom_2k_panel_magic_cmds),
>> +};
>> +
>> +static int truly_nt35597_probe(struct mipi_dsi_device *dsi)
>> +{
>> + struct device *dev = &dsi->dev;
>> + struct truly_nt35597 *ctx;
>> + struct mipi_dsi_device *dsi1_device;
>> + struct device_node *dsi1;
>> + struct mipi_dsi_host *dsi1_host;
>> + struct mipi_dsi_device *dsi_dev;
>> + int ret = 0;
>> + int i;
>> +
>> + const struct mipi_dsi_device_info info = {
>> + .type = "trulynt35597",
>> + .channel = 0,
>> + .node = NULL,
>> + };
>> +
>> + ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
>> +
>> + if (!ctx)
>> + return -ENOMEM;
>> +
>> + /*
>> + * This device represents itself as one with
>> + * two input ports which are fed by the output
>> + * ports of the two DSI controllers . The DSI0
>> + * is the master controller and has most of the
>> + * panel related info in its child node.
>> + */
>
> Your comments can be wider. It's typical to wrap at column 78, not
> earlier.
>
>> +
>> + ctx->config = of_device_get_match_data(dev);
>> +
>> + if (!ctx->config) {
>> + dev_err(dev, "missing device configuration\n");
>> + return -ENODEV;
>> + }
>> +
>> + dsi1 = of_graph_get_remote_node(dsi->dev.of_node, 1, -1);
>> + if (!dsi1) {
>> + DRM_DEV_ERROR(dev,
>> + "failed to get remote node for dsi1_device\n");
>> + return -ENODEV;
>> + }
>> +
>> + dsi1_host = of_find_mipi_dsi_host_by_node(dsi1);
>> + of_node_put(dsi1);
>> + if (!dsi1_host) {
>> + DRM_DEV_ERROR(dev, "failed to find dsi host\n");
>> + return -EPROBE_DEFER;
>> + }
>> +
>> + /* register the second DSI device */
>> + dsi1_device = mipi_dsi_device_register_full(dsi1_host, &info);
>> + if (IS_ERR(dsi1_device)) {
>> + DRM_DEV_ERROR(dev, "failed to create dsi device\n");
>> + return PTR_ERR(dsi);
>> + }
>
> Can you roll in the fix from here:
>
> https://patchwork.freedesktop.org/patch/245175/
>
>> +
>> + mipi_dsi_set_drvdata(dsi, ctx);
>> +
>> + ctx->dev = dev;
>> + ctx->dsi[0] = dsi;
>> + ctx->dsi[1] = dsi1_device;
>> +
>> + ret = truly_nt35597_panel_add(ctx);
>> + if (ret) {
>> + DRM_DEV_ERROR(dev, "failed to add panel\n");
>> + goto err_panel_add;
>> + }
>> +
>> + for (i = 0; i < ARRAY_SIZE(ctx->dsi); i++) {
>> + dsi_dev = ctx->dsi[i];
>> + dsi_dev->lanes = 4;
>> + dsi_dev->format = MIPI_DSI_FMT_RGB888;
>> + dsi_dev->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_LPM |
>> + MIPI_DSI_CLOCK_NON_CONTINUOUS;
>> + ret = mipi_dsi_attach(dsi_dev);
>> + if (ret < 0) {
>> + DRM_DEV_ERROR(dev,
>> + "dsi attach failed i = %d\n", i);
>> + goto err_dsi_attach;
>
> Indentation is wrong here. The goto should be indented one level less.
>
>> + }
>> + }
>> +
>> + return 0;
>> +
>> +err_dsi_attach:
>> + drm_panel_remove(&ctx->panel);
>> +err_panel_add:
>> + mipi_dsi_device_unregister(dsi1_device);
>> + return ret;
>> +}
>> +
>> +static int truly_nt35597_remove(struct mipi_dsi_device *dsi)
>> +{
>> + struct truly_nt35597 *ctx = mipi_dsi_get_drvdata(dsi);
>> +
>> + if (ctx->dsi[0])
>> + mipi_dsi_detach(ctx->dsi[0]);
>> + if (ctx->dsi[1]) {
>> + mipi_dsi_detach(ctx->dsi[1]);
>> + mipi_dsi_device_unregister(ctx->dsi[1]);
>> + }
>> +
>> + drm_panel_remove(&ctx->panel);
>> + return 0;
>> +}
>> +
>> +static const struct of_device_id truly_nt35597_of_match[] = {
>> + { .compatible = "truly,nt35597-2K-display",
>> + .data = &nt35597_dir,
>> + },
>> +
>> + { }
>
> The table is weirdly formatted. The ".compatible = ..." line should be
> an a separate line, and there should be no blank line before { }.
>
>> +};
>> +MODULE_DEVICE_TABLE(of, truly_nt35597_of_match);
>> +
>> +static struct mipi_dsi_driver truly_nt35597_driver = {
>> + .driver = {
>> + .name = "panel_truly_nt35597",
>
> You should use - instead of _ in the name for consistency with other
> drivers.
>
> Thanks,
> Thierry
>
>> + .of_match_table = truly_nt35597_of_match,
>> + },
>> + .probe = truly_nt35597_probe,
>> + .remove = truly_nt35597_remove,
>> +};
>> +module_mipi_dsi_driver(truly_nt35597_driver);
>> +
>> +MODULE_DESCRIPTION("Truly NT35597 DSI Panel Driver");
>> +MODULE_LICENSE("GPL v2");
>> --
>> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora
>> Forum,
>> a Linux Foundation Collaborative Project
>>
More information about the dri-devel
mailing list