[PATCH 2/2] drm/bridge: ti-tfp410: Set the bus_format
Andrzej Hajda
a.hajda at samsung.com
Fri Apr 12 07:40:28 UTC 2019
On 12.04.2019 09:33, Andrzej Hajda wrote:
> On 01.04.2019 14:41, Peter Ujfalusi wrote:
>> The TFP410 supports 24 bit, single-edge and 12 bit, dual-edge modes.
>> Depending on how many wires are used (24/12) the driver can set the correct
>> bus_format.
>>
>> If the information is not available in DT then assume 24 bit, single-edge
>> setup.
>>
>> Signed-off-by: Peter Ujfalusi <peter.ujfalusi at ti.com>
> Reviewed-by: Andrzej Hajda <a.hajda at samsung.com>
>
> The patch does not apply on drm-misc-next. Could you rebase it.
OK, with HPD patch applied it works, I will queue all three patches to
drm-misc-next.
Regards
Andrzej
>
>
> --
> Regards
> Andrzej
>
>> ---
>> drivers/gpu/drm/bridge/ti-tfp410.c | 17 +++++++++++++++++
>> 1 file changed, 17 insertions(+)
>>
>> diff --git a/drivers/gpu/drm/bridge/ti-tfp410.c b/drivers/gpu/drm/bridge/ti-tfp410.c
>> index 6fc831eb3804..8b0e71bd3ca7 100644
>> --- a/drivers/gpu/drm/bridge/ti-tfp410.c
>> +++ b/drivers/gpu/drm/bridge/ti-tfp410.c
>> @@ -29,6 +29,7 @@ struct tfp410 {
>> struct drm_connector connector;
>> unsigned int connector_type;
>>
>> + u32 bus_format;
>> struct i2c_adapter *ddc;
>> struct gpio_desc *hpd;
>> int hpd_irq;
>> @@ -139,6 +140,9 @@ static int tfp410_attach(struct drm_bridge *bridge)
>> return ret;
>> }
>>
>> + drm_display_info_set_bus_formats(&dvi->connector.display_info,
>> + &dvi->bus_format, 1);
>> +
>> drm_connector_attach_encoder(&dvi->connector,
>> bridge->encoder);
>>
>> @@ -197,6 +201,7 @@ static int tfp410_parse_timings(struct tfp410 *dvi, bool i2c)
>> struct drm_bridge_timings *timings = &dvi->timings;
>> struct device_node *ep;
>> u32 pclk_sample = 0;
>> + u32 bus_width = 24;
>> s32 deskew = 0;
>>
>> /* Start with defaults. */
>> @@ -221,6 +226,7 @@ static int tfp410_parse_timings(struct tfp410 *dvi, bool i2c)
>>
>> /* Get the sampling edge from the endpoint. */
>> of_property_read_u32(ep, "pclk-sample", &pclk_sample);
>> + of_property_read_u32(ep, "bus-width", &bus_width);
>> of_node_put(ep);
>>
>> timings->input_bus_flags = DRM_BUS_FLAG_DE_HIGH;
>> @@ -238,6 +244,17 @@ static int tfp410_parse_timings(struct tfp410 *dvi, bool i2c)
>> return -EINVAL;
>> }
>>
>> + switch (bus_width) {
>> + case 12:
>> + dvi->bus_format = MEDIA_BUS_FMT_RGB888_2X12_LE;
>> + break;
>> + case 24:
>> + dvi->bus_format = MEDIA_BUS_FMT_RGB888_1X24;
>> + break;
>> + default:
>> + return -EINVAL;
>> + }
>> +
>> /* Get the setup and hold time from vendor-specific properties. */
>> of_property_read_u32(dvi->dev->of_node, "ti,deskew", (u32 *)&deskew);
>> if (deskew < -4 || deskew > 3)
>
> _______________________________________________
> dri-devel mailing list
> dri-devel at lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/dri-devel
More information about the dri-devel
mailing list