[PATCH v2 3/9] dt-bindings: display: panel: Add bindings for NEC NL8048HL11 panel

[Laurent Pinchart]

Hi Rob,

On Mon, Aug 12, 2019 at 01:18:39PM -0600, Rob Herring wrote:
> On Sat, Aug 10, 2019 at 5:10 PM Laurent Pinchart wrote:
> >
> > The NEC NL8048HL11 is a 10.4cm WVGA (800x480) panel with a 24-bit RGB
> > parallel data interface and an SPI control interface.
> >
> > Signed-off-by: Laurent Pinchart <laurent.pinchart at ideasonboard.com>
> > ---
> > Changes since v1:
> >
> > - Convert to YAML
> > ---
> >  .../display/panel/nec,nl8048hl11.yaml         | 49 +++++++++++++++++++
> >  1 file changed, 49 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/display/panel/nec,nl8048hl11.yaml
> >
> > diff --git a/Documentation/devicetree/bindings/display/panel/nec,nl8048hl11.yaml b/Documentation/devicetree/bindings/display/panel/nec,nl8048hl11.yaml
> > new file mode 100644
> > index 000000000000..cc3d40975828
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/display/panel/nec,nl8048hl11.yaml
> > @@ -0,0 +1,49 @@
> > +# SPDX-License-Identifier: GPL-2.0
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/display/panel/nec,nl8048hl11.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: NEC NL8048HL11 4.1" WVGA TFT LCD panel
> > +
> > +description:
> > +  The NEC NL8048HL11 is a 4.1" WVGA TFT LCD panel with a 24-bit RGB parallel
> > +  data interface and an SPI control interface.
> > +
> > +maintainers:
> > +  - Laurent Pinchart <laurent.pinchart at ideasonboard.com>
> > +
> > +allOf:
> > +  - $ref: panel-common.yaml#
> > +
> > +properties:
> > +  compatible:
> > +    const: nec,nl8048hl11
> > +
> > +  label: true
> > +  reset-gpios: true
> > +  port: true
> > +
> > +required:
> > +  - compatible
> > +  - reset-gpios
> > +  - port
> > +
> > +additionalProperties: false
> > +
> > +examples:
> 
> Your example will fail on 'make dt_binding_check'...

I wasn't aware of this. I've now read writing-schema.md and will make
sure to submit bindings that pass the checks. I'll address the issues
your pointed out below for the next version.

> > +  - |
> > +    lcd_panel: panel {
> 
> SPI devices have to have a minimal SPI controller parent. Primarily
> just #size-cells and #address-cells are needed.
> 
> 'reg' is missing here too.
> 
> > +      compatible = "nec,nl8048hl11";
> > +      spi-max-frequency = <10000000>;
> 
> This needs to be listed in properties ideally with some constraints.
> 
> > +
> > +      reset-gpios = <&gpio7 7 GPIO_ACTIVE_LOW>;
> 
> And GPIO_ACTIVE_LOW. You have to add includes you need.
> 
> > +
> > +      port {
> > +        lcd_in: endpoint {
> > +          remote-endpoint = <&dpi_out>;
> > +        };
> > +      };
> > +    };
> > +
> > +...

-- 
Regards,

Laurent Pinchart