[PATCH] video/fbdev/aty128fb: Remove dead code

[Souptick Joarder]

On Wed, Aug 7, 2019 at 2:12 PM Souptick Joarder <jrdr.linux at gmail.com> wrote:
>
> On Wed, Jul 31, 2019 at 12:38 AM Souptick Joarder <jrdr.linux at gmail.com> wrote:
> >
> > This is dead code since 3.15. If there is no plan to use it
> > further, this can be removed forever.
>
> Any comment on this patch ?

Any comment on this patch ?

>
> >
> > Signed-off-by: Souptick Joarder <jrdr.linux at gmail.com>
> > ---
> >  drivers/video/fbdev/aty/aty128fb.c   | 18 ------------------
> >  drivers/video/fbdev/aty/atyfb_base.c | 29 -----------------------------
> >  2 files changed, 47 deletions(-)
> >
> > diff --git a/drivers/video/fbdev/aty/aty128fb.c b/drivers/video/fbdev/aty/aty128fb.c
> > index 8504e19..fc1e45d 100644
> > --- a/drivers/video/fbdev/aty/aty128fb.c
> > +++ b/drivers/video/fbdev/aty/aty128fb.c
> > @@ -487,11 +487,6 @@ static int aty128_encode_var(struct fb_var_screeninfo *var,
> >                               const struct aty128fb_par *par);
> >  static int aty128_decode_var(struct fb_var_screeninfo *var,
> >                               struct aty128fb_par *par);
> > -#if 0
> > -static void aty128_get_pllinfo(struct aty128fb_par *par, void __iomem *bios);
> > -static void __iomem *aty128_map_ROM(struct pci_dev *pdev,
> > -                                   const struct aty128fb_par *par);
> > -#endif
> >  static void aty128_timings(struct aty128fb_par *par);
> >  static void aty128_init_engine(struct aty128fb_par *par);
> >  static void aty128_reset_engine(const struct aty128fb_par *par);
> > @@ -1665,19 +1660,6 @@ static void aty128_st_pal(u_int regno, u_int red, u_int green, u_int blue,
> >                           struct aty128fb_par *par)
> >  {
> >         if (par->chip_gen == rage_M3) {
> > -#if 0
> > -               /* Note: For now, on M3, we set palette on both heads, which may
> > -                * be useless. Can someone with a M3 check this ?
> > -                *
> > -                * This code would still be useful if using the second CRTC to
> > -                * do mirroring
> > -                */
> > -
> > -               aty_st_le32(DAC_CNTL, aty_ld_le32(DAC_CNTL) |
> > -                           DAC_PALETTE_ACCESS_CNTL);
> > -               aty_st_8(PALETTE_INDEX, regno);
> > -               aty_st_le32(PALETTE_DATA, (red<<16)|(green<<8)|blue);
> > -#endif
> >                 aty_st_le32(DAC_CNTL, aty_ld_le32(DAC_CNTL) &
> >                             ~DAC_PALETTE_ACCESS_CNTL);
> >         }
> > diff --git a/drivers/video/fbdev/aty/atyfb_base.c b/drivers/video/fbdev/aty/atyfb_base.c
> > index 72bcfbe..6dda5d8 100644
> > --- a/drivers/video/fbdev/aty/atyfb_base.c
> > +++ b/drivers/video/fbdev/aty/atyfb_base.c
> > @@ -1188,19 +1188,6 @@ static int aty_crtc_to_var(const struct crtc *crtc,
> >                 (c_sync ? FB_SYNC_COMP_HIGH_ACT : 0);
> >
> >         switch (pix_width) {
> > -#if 0
> > -       case CRTC_PIX_WIDTH_4BPP:
> > -               bpp = 4;
> > -               var->red.offset = 0;
> > -               var->red.length = 8;
> > -               var->green.offset = 0;
> > -               var->green.length = 8;
> > -               var->blue.offset = 0;
> > -               var->blue.length = 8;
> > -               var->transp.offset = 0;
> > -               var->transp.length = 0;
> > -               break;
> > -#endif
> >         case CRTC_PIX_WIDTH_8BPP:
> >                 bpp = 8;
> >                 var->red.offset = 0;
> > @@ -1466,11 +1453,6 @@ static int atyfb_set_par(struct fb_info *info)
> >                 var->bits_per_pixel,
> >                 par->crtc.vxres * var->bits_per_pixel / 8);
> >  #endif /* CONFIG_BOOTX_TEXT */
> > -#if 0
> > -       /* switch to accelerator mode */
> > -       if (!(par->crtc.gen_cntl & CRTC_EXT_DISP_EN))
> > -               aty_st_le32(CRTC_GEN_CNTL, par->crtc.gen_cntl | CRTC_EXT_DISP_EN, par);
> > -#endif
> >  #ifdef DEBUG
> >  {
> >         /* dump non shadow CRTC, pll, LCD registers */
> > @@ -2396,17 +2378,6 @@ static int aty_init(struct fb_info *info)
> >                         par->pll_ops = &aty_pll_ibm514;
> >                         break;
> >  #endif
> > -#if 0 /* dead code */
> > -               case CLK_STG1703:
> > -                       par->pll_ops = &aty_pll_stg1703;
> > -                       break;
> > -               case CLK_CH8398:
> > -                       par->pll_ops = &aty_pll_ch8398;
> > -                       break;
> > -               case CLK_ATT20C408:
> > -                       par->pll_ops = &aty_pll_att20c408;
> > -                       break;
> > -#endif
> >                 default:
> >                         PRINTKI("aty_init: CLK type not implemented yet!");
> >                         par->pll_ops = &aty_pll_unsupported;
> > --
> > 1.9.1
> >