[PATCH RFC 18/19] drm/panel: simple: Add support for Toshiba LTA089AC29000 panel

[Boris Brezillon]

On Thu, 22 Aug 2019 03:36:32 +0300
Laurent Pinchart <laurent.pinchart at ideasonboard.com> wrote:

> Hi Boris,
> 
> Thank you for the patch.
> 
> On Thu, Aug 08, 2019 at 05:11:49PM +0200, Boris Brezillon wrote:
> > Add a new entry for the Toshiba LTA089AC29000 panel.
> > 
> > Signed-off-by: Boris Brezillon <boris.brezillon at collabora.com>
> > ---
> >  .../display/panel/toshiba,lt089ac29000.txt    |  5 ++-
> >  drivers/gpu/drm/panel/panel-simple.c          | 36 +++++++++++++++++++
> >  2 files changed, 40 insertions(+), 1 deletion(-)
> > 
> > diff --git a/Documentation/devicetree/bindings/display/panel/toshiba,lt089ac29000.txt b/Documentation/devicetree/bindings/display/panel/toshiba,lt089ac29000.txt
> > index 89826116628c..26ebfa098966 100644
> > --- a/Documentation/devicetree/bindings/display/panel/toshiba,lt089ac29000.txt
> > +++ b/Documentation/devicetree/bindings/display/panel/toshiba,lt089ac29000.txt
> > @@ -1,7 +1,10 @@
> >  Toshiba 8.9" WXGA (1280x768) TFT LCD panel
> >  
> >  Required properties:
> > -- compatible: should be "toshiba,lt089ac29000"
> > +- compatible: should be one of the following
> > +	      "toshiba,lt089ac29000"
> > +	      "toshiba,lta089ac29000"
> > +
> >  - power-supply: as specified in the base binding
> >  
> >  This binding is compatible with the simple-panel binding, which is specified  
> 
> While at it, any change to convert this binding to .yaml ? For panels
> it's fairly easy.

I'll add a patch doing that.

> 
> > diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c
> > index bff7578f84dd..4c1deed44ce2 100644
> > --- a/drivers/gpu/drm/panel/panel-simple.c
> > +++ b/drivers/gpu/drm/panel/panel-simple.c
> > @@ -2857,6 +2857,39 @@ static const struct panel_desc toshiba_lt089ac29000 = {
> >  	.bus_flags = DRM_BUS_FLAG_DE_HIGH | DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE,
> >  };
> >  
> > +static const struct drm_display_mode toshiba_lta089ac29000_mode = {
> > +	.clock = 79500,
> > +	.hdisplay = 1280,
> > +	.hsync_start = 1280 + 192,
> > +	.hsync_end = 1280 + 192 + 128,
> > +	.htotal = 1280 + 192 + 128 + 64,
> > +	.vdisplay = 768,
> > +	.vsync_start = 768 + 20,
> > +	.vsync_end = 768 + 20 + 7,
> > +	.vtotal = 768 + 20 + 7 + 3,
> > +	.vrefresh = 60,
> > +};
> > +
> > +static const struct panel_desc toshiba_lta089ac29000 = {
> > +	.modes = &toshiba_lta089ac29000_mode,
> > +	.num_modes = 1,
> > +	.size = {
> > +		.width = 194,
> > +		.height = 116,
> > +	},
> > +	/*
> > +	 * FIXME:
> > +	 * The panel supports 2 bus formats: jeida-24 and jeida-18. The
> > +	 * mode is selected through the 8b6b_SEL pin. If anyone ever needs
> > +	 * support for jeida-18 we should probably parse the 'data-mapping'
> > +	 * property.
> > +	 * In the unlikely event where 8b6b_SEL is connected to a GPIO, we'd
> > +	 * need a new infra to allow bus format negotiation at the panel level.  
> 
> I would also leave the GPIO case for later, but it would be nice to already
> implement reading the data-mapping property, in order to validate the DT
> (you should add the data-mapping property to the bindings by the way).

I'll do that.

> Bonus points if it can be done in a way that is also usable by other
> panels.

Sure, I'll make that code generic.

> 
> > +	 */
> > +	.bus_format = MEDIA_BUS_FMT_RGB888_1X7X4_JEIDA,
> > +	.bus_flags = DRM_BUS_FLAG_DE_HIGH | DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE,
> > +};
> > +
> >  static const struct drm_display_mode tpk_f07a_0102_mode = {
> >  	.clock = 33260,
> >  	.hdisplay = 800,
> > @@ -3305,6 +3338,9 @@ static const struct of_device_id platform_of_match[] = {
> >  	}, {
> >  		.compatible = "toshiba,lt089ac29000",
> >  		.data = &toshiba_lt089ac29000,
> > +	}, {
> > +		.compatible = "toshiba,lta089ac29000",
> > +		.data = &toshiba_lta089ac29000,
> >  	}, {
> >  		.compatible = "tpk,f07a-0102",
> >  		.data = &tpk_f07a_0102,  
>