[PATCH v2 11/12] arm64: allwinner: a64: enable LCD-related hardware for Pinebook

[Vasily Khoruzhick]

From: Icenowy Zheng <icenowy at aosc.io>

Pinebook has an ANX6345 bridge connected to the RGB666 LCD output and
eDP panel input. The bridge is controlled via I2C that's connected to
R_I2C bus.

Enable all this hardware in device tree.

Signed-off-by: Icenowy Zheng <icenowy at aosc.io>
Signed-off-by: Vasily Khoruzhick <anarsoul at gmail.com>
---
 .../dts/allwinner/sun50i-a64-pinebook.dts     | 74 +++++++++++++++++++
 1 file changed, 74 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts
index d22736a62481..49f5d4b0c7f4 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts
@@ -63,6 +63,18 @@
 		};
 	};
 
+	edp_panel: edp-panel {
+		compatible = "panel-edp", "simple-panel";
+		backlight = <&backlight>;
+		power-supply = <&reg_dc1sw>;
+
+		port {
+			panel_in_edp: endpoint {
+				remote-endpoint = <&anx6345_out_panel>;
+			};
+		};
+	};
+
 	reg_vcc3v3: vcc3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc3v3";
@@ -102,6 +114,10 @@
 	status = "okay";
 };
 
+&de {
+	status = "okay";
+};
+
 &ehci0 {
 	phys = <&usbphy 0>;
 	phy-names = "usb";
@@ -112,6 +128,10 @@
 	status = "okay";
 };
 
+&mixer0 {
+	status = "okay";
+};
+
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
@@ -163,6 +183,46 @@
 	status = "okay";
 };
 
+&r_i2c {
+	pinctrl-names = "default";
+	pinctrl-0 = <&r_i2c_pins_a>;
+	status = "okay";
+
+	anx6345: anx6345 at 38 {
+		compatible = "analogix,anx6345";
+		reg = <0x38>;
+		reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
+		dvdd25-supply = <&reg_dldo2>;
+		dvdd12-supply = <&reg_fldo1>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			anx6345_in: port at 0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;
+				anx6345_in_tcon0: endpoint at 0 {
+					reg = <0>;
+					remote-endpoint = <&tcon0_out_anx6345>;
+				};
+			};
+
+			anx6345_out: port at 1 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <1>;
+
+				anx6345_out_panel: endpoint at 0 {
+					reg = <0>;
+					remote-endpoint = <&panel_in_edp>;
+				};
+			};
+		};
+	};
+};
+
 &r_rsb {
 	status = "okay";
 
@@ -334,6 +394,20 @@
 			"MIC2", "Internal Microphone Right";
 };
 
+&tcon0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcd_rgb666_pins>;
+
+	status = "okay";
+};
+
+&tcon0_out {
+	tcon0_out_anx6345: endpoint at 0 {
+		reg = <0>;
+		remote-endpoint = <&anx6345_in_tcon0>;
+	};
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pb_pins>;
-- 
2.20.1