[PATCH v2 3/3] drm/panel: simple: add support for PDA 91-00156-A0 panel

[Sam Ravnborg]

Hi Eugen.

Patch looks good, but a small improvement proposal.

On Mon, Jan 14, 2019 at 09:43:31AM +0000, Eugen.Hristev at microchip.com wrote:
> From: Eugen Hristev <eugen.hristev at microchip.com>
> 
> PDA 91-00156-A0 5.0 is a 5.0" WVGA TFT LCD panel.
> This panel with backlight is found in PDA 5" LCD screen (TM5000 series or
> AC320005-5).
> 
> Signed-off-by: Eugen Hristev <eugen.hristev at microchip.com>
> ---
>  drivers/gpu/drm/panel/panel-simple.c | 27 +++++++++++++++++++++++++++
>  1 file changed, 27 insertions(+)
> 
> diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c
> index 9c69e73..61361ba 100644
> --- a/drivers/gpu/drm/panel/panel-simple.c
> +++ b/drivers/gpu/drm/panel/panel-simple.c
> @@ -2008,6 +2008,30 @@ static const struct panel_desc ortustech_com43h4m85ulc = {
>  	.bus_flags = DRM_BUS_FLAG_DE_HIGH | DRM_BUS_FLAG_PIXDATA_POSEDGE,
>  };
>  
> +static const struct drm_display_mode pda_91_00156_a0_mode = {
> +	.clock = 33300,
> +	.hdisplay = 800,
> +	.hsync_start = 800 + 1,
> +	.hsync_end = 800 + 1 + 64,
> +	.htotal = 800 + 1 + 64 + 64,
> +	.vdisplay = 480,
> +	.vsync_start = 480 + 1,
> +	.vsync_end = 480 + 1 + 23,
> +	.vtotal = 480 + 1 + 23 + 22,
> +	.vrefresh = 60,
> +};
.flags are omitted, as it is for many panels in simple-panel.
drm_modes.h do not document any default, so we must assume default equals no flags.

I would expect two of these as a minimum:
DRM_MODE_FLAG_PHSYNC: horizontal sync is active high.
DRM_MODE_FLAG_NHSYNC: horizontal sync is active low.
DRM_MODE_FLAG_PVSYNC: vertical sync is active high.
DRM_MODE_FLAG_NVSYNC: vertical sync is active low.

But it obviously works for a lot of panel, so one
may say why bother with it.

> +
> +static const struct panel_desc pda_91_00156_a0  = {
> +	.modes = &pda_91_00156_a0_mode,
> +	.num_modes = 1,
> +	.size = {
> +		.width = 152,
> +		.height = 91,
> +	},
> +	.bus_format = MEDIA_BUS_FMT_RGB888_1X24,
> +};
.bus_format is specified - good!

Consider if .bus_flags needs to be specified.
(More or less same argumentation like for .flags above).

I could not find any data-sheet on the panel,
so I could not check if it is OK that all delays are 0.

So to recap - things looks fine, but consider to be more explicit
in .flags, bus_flags, and check if it is OK that all timing parameters are 0.

	Sam