[PATCH 4/5] drm/tegra: Restrict IOVA space to DMA mask

[Dmitry Osipenko]

23.01.2019 18:55, Dmitry Osipenko пишет:
> 23.01.2019 17:04, Thierry Reding пишет:
>> On Wed, Jan 23, 2019 at 04:41:44PM +0300, Dmitry Osipenko wrote:
>>> 23.01.2019 12:39, Thierry Reding пишет:
>>>> From: Thierry Reding <treding at nvidia.com>
>>>>
>>>> On Tegra186 and later, the ARM SMMU provides an input address space that
>>>> is 48 bits wide. However, memory clients can only address up to 40 bits.
>>>> If the geometry is used as-is, allocations of IOVA space can end up in a
>>>> region that cannot be addressed by the memory clients.
>>>>
>>>> To fix this, restrict the IOVA space to the DMA mask of the host1x
>>>> device. Note that, technically, the IOVA space needs to be restricted to
>>>> the intersection of the DMA masks for all clients that are attached to
>>>> the IOMMU domain. In practice using the DMA mask of the host1x device is
>>>> sufficient because all host1x clients share the same DMA mask.
>>>>
>>>> Signed-off-by: Thierry Reding <treding at nvidia.com>
>>>> ---
>>>>  drivers/gpu/drm/tegra/drm.c | 5 +++--
>>>>  1 file changed, 3 insertions(+), 2 deletions(-)
>>>>
>>>> diff --git a/drivers/gpu/drm/tegra/drm.c b/drivers/gpu/drm/tegra/drm.c
>>>> index 271c7a5fc954..0c5f1e6a0446 100644
>>>> --- a/drivers/gpu/drm/tegra/drm.c
>>>> +++ b/drivers/gpu/drm/tegra/drm.c
>>>> @@ -136,11 +136,12 @@ static int tegra_drm_load(struct drm_device *drm, unsigned long flags)
>>>>  
>>>>  	if (tegra->domain) {
>>>>  		u64 carveout_start, carveout_end, gem_start, gem_end;
>>>> +		u64 dma_mask = dma_get_mask(&device->dev);
>>>>  		dma_addr_t start, end;
>>>>  		unsigned long order;
>>>>  
>>>> -		start = tegra->domain->geometry.aperture_start;
>>>> -		end = tegra->domain->geometry.aperture_end;
>>>> +		start = tegra->domain->geometry.aperture_start & dma_mask;
>>>> +		end = tegra->domain->geometry.aperture_end & dma_mask;
>>>>  
>>>>  		gem_start = start;
>>>>  		gem_end = end - CARVEOUT_SZ;
>>>>
>>>
>>> Wow, so IOVA could address >32bits on later Tegra's. AFAIK, currently
>>> there is no support for a proper programming of the 64bit addresses in
>>> the drivers code, hence.. won't it make sense to force IOVA mask to
>>> 32bit for now and hope that the second halve of address registers
>>> happen to be 0x00000000 in HW?
>>
>> I think this restriction only applies to display at this point. In
>> practice you'd be hard put to trigger that case because IOVA memory is
>> allocated from the bottom, so you'd actually need to use up to 4 GiB of
>> IOVA space before hitting that.
>>
>> That said, I vaguely remember typing up the patch to support writing the
>> WINBUF_START_ADDR_HI register and friends, but it looks as if that was
>> never merged.
>>
>> I'll try to dig out that patch (or rewrite it, shouldn't be very
>> difficult) and make it part of this series. I'd rather fix that issue
>> than arbitrarily restrict the IOVA space, because that's likely to come
>> back and bite us at some point.
> 
> Looking at falcon.c.. it writes 32bit address only. Something need to be done about it as well, seems there is FALCON_DMATRFMOFFS register to facilitate >32bits addressing.

Although scratch about FALCON_DMATRFMOFFS, it should be about something else. Mikko, could you please clarify whether falcon could load firmware only from a 32bit AS?