[PATCH 08/11] ARM: dts: sun8i-a33: Move display pipeline nodes to a23/a33 common dtsi
Chen-Yu Tsai
wens at csie.org
Fri Jan 25 03:23:11 UTC 2019
The display pipeline has the same structure, resources and connections
on both the A23 and A33. The differences include:
- compatible strings
- extra clock, reset control, and IO region for SAT in the backend
only found on the A33
- missing ch1 clock for the TCON
However, while the A23 has the TCON ch1 clock defined in the CCU, and
the channel 1 registers are available, it does not have any means to
use channel 1 due to a lack of downstream encoders, and the enable bit
for channel 1 is hard-wired to 0 (off).
As the MIPI DSI output device is not officially documented, and there
are no A23 reference devices to test it, it is not covered by this
patch.
Signed-off-by: Chen-Yu Tsai <wens at csie.org>
---
arch/arm/boot/dts/sun8i-a23-a33.dtsi | 147 ++++++++++++++++++++
arch/arm/boot/dts/sun8i-a33.dtsi | 194 ++++++---------------------
2 files changed, 185 insertions(+), 156 deletions(-)
diff --git a/arch/arm/boot/dts/sun8i-a23-a33.dtsi b/arch/arm/boot/dts/sun8i-a23-a33.dtsi
index 97ec8b8cec09..43fe215e83ea 100644
--- a/arch/arm/boot/dts/sun8i-a23-a33.dtsi
+++ b/arch/arm/boot/dts/sun8i-a23-a33.dtsi
@@ -68,6 +68,12 @@
};
};
+ de: display-engine {
+ /* compatible gets set in SoC specific dtsi file */
+ allwinner,pipelines = <&fe0>;
+ status = "disabled";
+ };
+
timer {
compatible = "arm,armv7-timer";
interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
@@ -168,6 +174,42 @@
#size-cells = <0>;
};
+ tcon0: lcd-controller at 1c0c000 {
+ /* compatible gets set in SoC specific dtsi file */
+ reg = <0x01c0c000 0x1000>;
+ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_LCD>,
+ <&ccu CLK_LCD_CH0>;
+ clock-names = "ahb",
+ "tcon-ch0";
+ clock-output-names = "tcon-pixel-clock";
+ resets = <&ccu RST_BUS_LCD>;
+ reset-names = "lcd";
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon0_in: port at 0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ tcon0_in_drc0: endpoint at 0 {
+ reg = <0>;
+ remote-endpoint = <&drc0_out_tcon0>;
+ };
+ };
+
+ tcon0_out: port at 1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+ };
+ };
+
mmc0: mmc at 1c0f000 {
compatible = "allwinner,sun7i-a20-mmc";
reg = <0x01c0f000 0x1000>;
@@ -570,6 +612,111 @@
interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
};
+ fe0: display-frontend at 1e00000 {
+ /* compatible gets set in SoC specific dtsi file */
+ reg = <0x01e00000 0x20000>;
+ interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_DE_FE>, <&ccu CLK_DE_FE>,
+ <&ccu CLK_DRAM_DE_FE>;
+ clock-names = "ahb", "mod",
+ "ram";
+ resets = <&ccu RST_BUS_DE_FE>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fe0_out: port at 1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ fe0_out_be0: endpoint at 0 {
+ reg = <0>;
+ remote-endpoint = <&be0_in_fe0>;
+ };
+ };
+ };
+ };
+
+ be0: display-backend at 1e60000 {
+ /* compatible gets set in SoC specific dtsi file */
+ reg = <0x01e60000 0x10000>;
+ interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_DE_BE>, <&ccu CLK_DE_BE>,
+ <&ccu CLK_DRAM_DE_BE>;
+ clock-names = "ahb", "mod",
+ "ram";
+ resets = <&ccu RST_BUS_DE_BE>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ be0_in: port at 0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ be0_in_fe0: endpoint at 0 {
+ reg = <0>;
+ remote-endpoint = <&fe0_out_be0>;
+ };
+ };
+
+ be0_out: port at 1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ be0_out_drc0: endpoint at 0 {
+ reg = <0>;
+ remote-endpoint = <&drc0_in_be0>;
+ };
+ };
+ };
+ };
+
+ drc0: drc at 1e70000 {
+ /* compatible gets set in SoC specific dtsi file */
+ reg = <0x01e70000 0x10000>;
+ interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_DRC>, <&ccu CLK_DRC>,
+ <&ccu CLK_DRAM_DRC>;
+ clock-names = "ahb", "mod", "ram";
+ resets = <&ccu RST_BUS_DRC>;
+
+ assigned-clocks = <&ccu CLK_DRC>;
+ assigned-clock-rates = <300000000>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ drc0_in: port at 0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ drc0_in_be0: endpoint at 0 {
+ reg = <0>;
+ remote-endpoint = <&be0_out_drc0>;
+ };
+ };
+
+ drc0_out: port at 1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ drc0_out_tcon0: endpoint at 0 {
+ reg = <0>;
+ remote-endpoint = <&tcon0_in_drc0>;
+ };
+ };
+ };
+ };
+
rtc: rtc at 1f00000 {
compatible = "allwinner,sun8i-a23-rtc";
reg = <0x01f00000 0x400>;
diff --git a/arch/arm/boot/dts/sun8i-a33.dtsi b/arch/arm/boot/dts/sun8i-a33.dtsi
index 626152c30f50..1111a6498102 100644
--- a/arch/arm/boot/dts/sun8i-a33.dtsi
+++ b/arch/arm/boot/dts/sun8i-a33.dtsi
@@ -159,12 +159,6 @@
};
};
- de: display-engine {
- compatible = "allwinner,sun8i-a33-display-engine";
- allwinner,pipelines = <&fe0>;
- status = "disabled";
- };
-
iio-hwmon {
compatible = "iio-hwmon";
io-channels = <&ths>;
@@ -209,47 +203,6 @@
};
soc {
- tcon0: lcd-controller at 1c0c000 {
- compatible = "allwinner,sun8i-a33-tcon";
- reg = <0x01c0c000 0x1000>;
- interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_LCD>,
- <&ccu CLK_LCD_CH0>;
- clock-names = "ahb",
- "tcon-ch0";
- clock-output-names = "tcon-pixel-clock";
- resets = <&ccu RST_BUS_LCD>;
- reset-names = "lcd";
- status = "disabled";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- tcon0_in: port at 0 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
-
- tcon0_in_drc0: endpoint at 0 {
- reg = <0>;
- remote-endpoint = <&drc0_out_tcon0>;
- };
- };
-
- tcon0_out: port at 1 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <1>;
-
- tcon0_out_dsi: endpoint at 1 {
- reg = <1>;
- remote-endpoint = <&dsi_in_tcon0>;
- };
- };
- };
- };
-
video-codec at 1c0e000 {
compatible = "allwinner,sun8i-a33-video-engine";
reg = <0x01c0e000 0x1000>;
@@ -339,115 +292,6 @@
status = "disabled";
#phy-cells = <0>;
};
-
- fe0: display-frontend at 1e00000 {
- compatible = "allwinner,sun8i-a33-display-frontend";
- reg = <0x01e00000 0x20000>;
- interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_DE_FE>, <&ccu CLK_DE_FE>,
- <&ccu CLK_DRAM_DE_FE>;
- clock-names = "ahb", "mod",
- "ram";
- resets = <&ccu RST_BUS_DE_FE>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- fe0_out: port at 1 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <1>;
-
- fe0_out_be0: endpoint at 0 {
- reg = <0>;
- remote-endpoint = <&be0_in_fe0>;
- };
- };
- };
- };
-
- be0: display-backend at 1e60000 {
- compatible = "allwinner,sun8i-a33-display-backend";
- reg = <0x01e60000 0x10000>, <0x01e80000 0x1000>;
- reg-names = "be", "sat";
- interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_DE_BE>, <&ccu CLK_DE_BE>,
- <&ccu CLK_DRAM_DE_BE>, <&ccu CLK_BUS_SAT>;
- clock-names = "ahb", "mod",
- "ram", "sat";
- resets = <&ccu RST_BUS_DE_BE>, <&ccu RST_BUS_SAT>;
- reset-names = "be", "sat";
- assigned-clocks = <&ccu CLK_DE_BE>;
- assigned-clock-rates = <300000000>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- be0_in: port at 0 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
-
- be0_in_fe0: endpoint at 0 {
- reg = <0>;
- remote-endpoint = <&fe0_out_be0>;
- };
- };
-
- be0_out: port at 1 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <1>;
-
- be0_out_drc0: endpoint at 0 {
- reg = <0>;
- remote-endpoint = <&drc0_in_be0>;
- };
- };
- };
- };
-
- drc0: drc at 1e70000 {
- compatible = "allwinner,sun8i-a33-drc";
- reg = <0x01e70000 0x10000>;
- interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_DRC>, <&ccu CLK_DRC>,
- <&ccu CLK_DRAM_DRC>;
- clock-names = "ahb", "mod", "ram";
- resets = <&ccu RST_BUS_DRC>;
-
- assigned-clocks = <&ccu CLK_DRC>;
- assigned-clock-rates = <300000000>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- drc0_in: port at 0 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
-
- drc0_in_be0: endpoint at 0 {
- reg = <0>;
- remote-endpoint = <&be0_out_drc0>;
- };
- };
-
- drc0_out: port at 1 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <1>;
-
- drc0_out_tcon0: endpoint at 0 {
- reg = <0>;
- remote-endpoint = <&tcon0_in_drc0>;
- };
- };
- };
- };
};
thermal-zones {
@@ -524,10 +368,37 @@
};
};
+&be0 {
+ compatible = "allwinner,sun8i-a33-display-backend";
+ /* A33 has an extra "SAT" module packed inside the display backend */
+ reg = <0x01e60000 0x10000>, <0x01e80000 0x1000>;
+ reg-names = "be", "sat";
+ clocks = <&ccu CLK_BUS_DE_BE>, <&ccu CLK_DE_BE>,
+ <&ccu CLK_DRAM_DE_BE>, <&ccu CLK_BUS_SAT>;
+ clock-names = "ahb", "mod",
+ "ram", "sat";
+ resets = <&ccu RST_BUS_DE_BE>, <&ccu RST_BUS_SAT>;
+ reset-names = "be", "sat";
+ assigned-clocks = <&ccu CLK_DE_BE>;
+ assigned-clock-rates = <300000000>;
+};
+
&ccu {
compatible = "allwinner,sun8i-a33-ccu";
};
+&de {
+ compatible = "allwinner,sun8i-a33-display-engine";
+};
+
+&drc0 {
+ compatible = "allwinner,sun8i-a33-drc";
+};
+
+&fe0 {
+ compatible = "allwinner,sun8i-a33-display-frontend";
+};
+
&mali {
operating-points-v2 = <&mali_opp_table>;
};
@@ -544,6 +415,17 @@
};
+&tcon0 {
+ compatible = "allwinner,sun8i-a33-tcon";
+};
+
+&tcon0_out {
+ tcon0_out_dsi: endpoint at 1 {
+ reg = <1>;
+ remote-endpoint = <&dsi_in_tcon0>;
+ };
+};
+
&usb_otg {
compatible = "allwinner,sun8i-a33-musb";
};
--
2.20.1
More information about the dri-devel
mailing list