drm/msm/dpu: Correct dpu encoder spinlock initialization

[Jeykumar Sankaran]

On 2019-07-01 03:29, dhar at codeaurora.org wrote:
> On 2019-06-26 03:10, Jeykumar Sankaran wrote:
>> On 2019-06-24 22:44, dhar at codeaurora.org wrote:
>>> On 2019-06-25 03:56, Jeykumar Sankaran wrote:
>>>> On 2019-06-23 23:27, Shubhashree Dhar wrote:
>>>>> dpu encoder spinlock should be initialized during dpu encoder
>>>>> init instead of dpu encoder setup which is part of commit.
>>>>> There are chances that vblank control uses the uninitialized
>>>>> spinlock if not initialized during encoder init.
>>>> Not much can be done if someone is performing a vblank operation
>>>> before encoder_setup is done.
>>>> Can you point to the path where this lock is acquired before
>>>> the encoder_setup?
>>>> 
>>>> Thanks
>>>> Jeykumar S.
>>>>> 
>>> 
>>> When running some dp usecase, we are hitting this callstack.
>>> 
>>> Process kworker/u16:8 (pid: 215, stack limit = 0x00000000df9dd930)
>>> Call trace:
>>>  spin_dump+0x84/0x8c
>>>  spin_dump+0x0/0x8c
>>>  do_raw_spin_lock+0x80/0xb0
>>>  _raw_spin_lock_irqsave+0x34/0x44
>>>  dpu_encoder_toggle_vblank_for_crtc+0x8c/0xe8
>>>  dpu_crtc_vblank+0x168/0x1a0
>>>  dpu_kms_enable_vblank+0[   11.648998]  vblank_ctrl_worker+0x3c/0x60
>>>  process_one_work+0x16c/0x2d8
>>>  worker_thread+0x1d8/0x2b0
>>>  kthread+0x124/0x134
>>> 
>>> Looks like vblank is getting enabled earlier causing this issue and 
>>> we
>>> are using the spinlock without initializing it.
>>> 
>>> Thanks,
>>> Shubhashree
>>> 
>> DP calls into set_encoder_mode during hotplug before even notifying 
>> the
>> u/s. Can you trace out the original caller of this stack?
>> 
>> Even though the patch is harmless, I am not entirely convinced to move 
>> this
>> initialization. Any call which acquires the lock before encoder_setup
>> will be a no-op since there will not be any physical encoder to work 
>> with.
>> 
>> Thanks and Regards,
>> Jeykumar S.
>> 
>>>>> Change-Id: I5a18b95fa47397c834a266b22abf33a517b03a4e
>>>>> Signed-off-by: Shubhashree Dhar <dhar at codeaurora.org>
>>>>> ---
>>>>>  drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c | 3 +--
>>>>>  1 file changed, 1 insertion(+), 2 deletions(-)
>>>>> 
>>>>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
>>>>> b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
>>>>> index 5f085b5..22938c7 100644
>>>>> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
>>>>> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c
>>>>> @@ -2195,8 +2195,6 @@ int dpu_encoder_setup(struct drm_device *dev, 
>>>>> struct
>>>>> drm_encoder *enc,
>>>>>  	if (ret)
>>>>>  		goto fail;
>>>>> 
>>>>> -	spin_lock_init(&dpu_enc->enc_spinlock);
>>>>> -
>>>>>  	atomic_set(&dpu_enc->frame_done_timeout, 0);
>>>>>  	timer_setup(&dpu_enc->frame_done_timer,
>>>>>  			dpu_encoder_frame_done_timeout, 0);
>>>>> @@ -2250,6 +2248,7 @@ struct drm_encoder *dpu_encoder_init(struct
>>>>> drm_device *dev,
>>>>> 
>>>>>  	drm_encoder_helper_add(&dpu_enc->base, 
>>>>> &dpu_encoder_helper_funcs);
>>>>> 
>>>>> +	spin_lock_init(&dpu_enc->enc_spinlock);
>>>>>  	dpu_enc->enabled = false;
>>>>> 
>>>>>  	return &dpu_enc->base;
> 
> In dpu_crtc_vblank(), we are looping through all the encoders in the
> present mode_config:
> https://github.com/torvalds/linux/blob/master/drivers/gpu/drm/msm/disp/dpu
> 1/dpu_crtc.c#L1082
> and hence calling dpu_encoder_toggle_vblank_for_crtc() for all the
> encoders. But in dpu_encoder_toggle_vblank_for_crtc(), after acquiring
> the spinlock, we will do a early return for
> the encoders which are not currently assigned to our crtc:
> https://github.com/torvalds/linux/blob/master/drivers/gpu/drm/msm/disp/dpu
> 1/dpu_encoder.c#L1318.
> Since the encoder_setup for the secondary encoder(dp encoder in this
> case) is not called until dp hotplug, we are hitting kernel panic
> while acquiring the lock.
This is the sequence in which the events are expected to happen:

1) DP connector is instantiated with an inactive state
2) Hot plug on DP
3) DP connector is activated
4) User space attaches a CRTC to the activated connector
5) CRTC is enabled
6) CRTC_VBLANK_ON is called
7) dpu_crtc_vblank is called.

So can you help tracing out why dpu_crtc_vblank is called when the 
connector
is not activated yet (no hotplug)?

-- 
Jeykumar S