[PATCH 1/2] dt-bindings: backlight: fix vendor prefix for ArcticSand arcxcnn driver bindings

[Daniel Thompson]

On Tue, Jun 25, 2019 at 12:05:28AM -0400, Brian Dodge wrote:
>     The vendor-prefixes.txt file properly refers to ArcticSand
>     as arctic but the driver bindings improperly abbreviated the
>     prefix to arc. This was a mistake in the original patch
> 
> Signed-off-by: Brian Dodge <bdodge09 at gmail.com>
> ---
>  .../bindings/leds/backlight/arcxcnn_bl.txt         | 24 +++++++++++++---------
>  1 file changed, 14 insertions(+), 10 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
> index 230abde..9cf4c44 100644
> --- a/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
> +++ b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
> @@ -1,8 +1,12 @@
> -Binding for ArcticSand arc2c0608 LED driver
> +Binding for ArcticSand arc family LED drivers
>  
>  Required properties:
> -- compatible:		should be "arc,arc2c0608"
> -- reg:			slave address
> +- compatible: one of
> +	"arctic,arc1c0608"
> +	"arctic,arc2c0608"
> +	"arctic,arc3c0845"

This is more a question for the DT folks than for Brian but...

AFAICT this patch is fixing the binding for the ArcticSand devices to
use the correct value from vendor-prefixes.yaml and has been previously
discussed here:
https://lkml.org/lkml/2018/9/25/726

Currently this patch series just updates the DT bindings but the
implementation also honours the old values (since there is a Chromebook
in the wild that uses the current bindings).

Hence I'm not clear whether the bindings should document the deprecated
options too (e.g. make it easier to find the bindings doc with git grep
and friends).


Daniel.


> +
> +- reg:		slave address
>  
>  Optional properties:
>  - default-brightness:	brightness value on boot, value from: 0-4095
> @@ -11,19 +15,19 @@ Optional properties:
>  - led-sources:		List of enabled channels from 0 to 5.
>  			See Documentation/devicetree/bindings/leds/common.txt
>  
> -- arc,led-config-0:	setting for register ILED_CONFIG_0
> -- arc,led-config-1:	setting for register ILED_CONFIG_1
> -- arc,dim-freq:		PWM mode frequence setting (bits [3:0] used)
> -- arc,comp-config:	setting for register CONFIG_COMP
> -- arc,filter-config:	setting for register FILTER_CONFIG
> -- arc,trim-config:	setting for register IMAXTUNE
> +- arctic,led-config-0:	setting for register ILED_CONFIG_0
> +- arctic,led-config-1:	setting for register ILED_CONFIG_1
> +- arctic,dim-freq:		PWM mode frequence setting (bits [3:0] used)
> +- arctic,comp-config:	setting for register CONFIG_COMP
> +- arctic,filter-config:	setting for register FILTER_CONFIG
> +- arctic,trim-config:	setting for register IMAXTUNE
>  
>  Note: Optional properties not specified will default to values in IC EPROM
>  
>  Example:
>  
>  arc2c0608 at 30 {
> -	compatible = "arc,arc2c0608";
> +	compatible = "arctic,arc2c0608";
>  	reg = <0x30>;
>  	default-brightness = <500>;
>  	label = "lcd-backlight";
> -- 
> 2.7.4
>