[PATCH 1/2] dt-bindings: backlight: fix vendor prefix for ArcticSand arcxcnn driver bindings
Dan Murphy
dmurphy at ti.com
Wed Jun 26 11:44:10 UTC 2019
Hello
On 6/25/19 3:55 AM, Daniel Thompson wrote:
> On Tue, Jun 25, 2019 at 12:05:28AM -0400, Brian Dodge wrote:
>> The vendor-prefixes.txt file properly refers to ArcticSand
>> as arctic but the driver bindings improperly abbreviated the
>> prefix to arc. This was a mistake in the original patch
>>
>> Signed-off-by: Brian Dodge <bdodge09 at gmail.com>
>> ---
>> .../bindings/leds/backlight/arcxcnn_bl.txt | 24 +++++++++++++---------
>> 1 file changed, 14 insertions(+), 10 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
>> index 230abde..9cf4c44 100644
>> --- a/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
>> +++ b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
>> @@ -1,8 +1,12 @@
>> -Binding for ArcticSand arc2c0608 LED driver
>> +Binding for ArcticSand arc family LED drivers
>>
>> Required properties:
>> -- compatible: should be "arc,arc2c0608"
>> -- reg: slave address
>> +- compatible: one of
>> + "arctic,arc1c0608"
>> + "arctic,arc2c0608"
>> + "arctic,arc3c0845"
> This is more a question for the DT folks than for Brian but...
>
> AFAICT this patch is fixing the binding for the ArcticSand devices to
> use the correct value from vendor-prefixes.yaml and has been previously
> discussed here:
> https://lkml.org/lkml/2018/9/25/726
>
> Currently this patch series just updates the DT bindings but the
> implementation also honours the old values (since there is a Chromebook
> in the wild that uses the current bindings).
>
> Hence I'm not clear whether the bindings should document the deprecated
> options too (e.g. make it easier to find the bindings doc with git grep
> and friends).
>
>
> Daniel.
>
>
>> +
>> +- reg: slave address
>>
>> Optional properties:
>> - default-brightness: brightness value on boot, value from: 0-4095
>> @@ -11,19 +15,19 @@ Optional properties:
>> - led-sources: List of enabled channels from 0 to 5.
>> See Documentation/devicetree/bindings/leds/common.txt
>>
>> -- arc,led-config-0: setting for register ILED_CONFIG_0
>> -- arc,led-config-1: setting for register ILED_CONFIG_1
>> -- arc,dim-freq: PWM mode frequence setting (bits [3:0] used)
>> -- arc,comp-config: setting for register CONFIG_COMP
>> -- arc,filter-config: setting for register FILTER_CONFIG
>> -- arc,trim-config: setting for register IMAXTUNE
IMO I would prefer to keep these and mark them as deprecated since the
driver will still
honor these properties.
Maybe in a Optional Deprecated Properties section in the DT binding.
Dan
>> +- arctic,led-config-0: setting for register ILED_CONFIG_0
>> +- arctic,led-config-1: setting for register ILED_CONFIG_1
>> +- arctic,dim-freq: PWM mode frequence setting (bits [3:0] used)
>> +- arctic,comp-config: setting for register CONFIG_COMP
>> +- arctic,filter-config: setting for register FILTER_CONFIG
>> +- arctic,trim-config: setting for register IMAXTUNE
>>
>> Note: Optional properties not specified will default to values in IC EPROM
>>
>> Example:
>>
>> arc2c0608 at 30 {
>> - compatible = "arc,arc2c0608";
>> + compatible = "arctic,arc2c0608";
>> reg = <0x30>;
>> default-brightness = <500>;
>> label = "lcd-backlight";
>> --
>> 2.7.4
>>
More information about the dri-devel
mailing list