[PATCH 5/6] drm/bridge: Add Chipone ICN6211 MIPI-DSI/RGB convertor bridge
Maxime Ripard
maxime.ripard at bootlin.com
Fri Mar 15 13:33:04 UTC 2019
On Fri, Mar 15, 2019 at 06:38:24PM +0530, Jagan Teki wrote:
> ICN6211 is MIPI-DSI/RGB converter bridge from chipone.
> It has a flexible configuration of MIPI DSI signal input
> and produce RGB565, RGB666, RGB888 output format.
>
> Add bridge driver for it.
>
> Signed-off-by: Jagan Teki <jagan at amarulasolutions.com>
> ---
> MAINTAINERS | 6 +
> drivers/gpu/drm/bridge/Kconfig | 10 +
> drivers/gpu/drm/bridge/Makefile | 1 +
> drivers/gpu/drm/bridge/chipone-icn6211.c | 275 +++++++++++++++++++++++
> 4 files changed, 292 insertions(+)
> create mode 100644 drivers/gpu/drm/bridge/chipone-icn6211.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 4de80222cffb..e529addd30f5 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -4897,6 +4897,12 @@ T: git git://anongit.freedesktop.org/drm/drm-misc
> S: Maintained
> F: drivers/gpu/drm/bochs/
>
> +DRM DRIVER FOR CHIPONE ICN6211 MIPI-DSI to RGB CONVERTOR BRIDGE
> +M: Jagan Teki <jagan at amarulasolutions.com>
> +S: Maintained
> +F: drivers/gpu/drm/bridge/chipone-icn6211.c
> +F: Documentation/devicetree/bindings/display/bridge/chipone,icn6211.txt
> +
> DRM DRIVER FOR FARADAY TVE200 TV ENCODER
> M: Linus Walleij <linus.walleij at linaro.org>
> T: git git://anongit.freedesktop.org/drm/drm-misc
> diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
> index 8840f396a7b6..cd314572e4ed 100644
> --- a/drivers/gpu/drm/bridge/Kconfig
> +++ b/drivers/gpu/drm/bridge/Kconfig
> @@ -36,6 +36,16 @@ config DRM_CDNS_DSI
> Support Cadence DPI to DSI bridge. This is an internal
> bridge and is meant to be directly embedded in a SoC.
>
> +config DRM_CHIPONE_ICN6211
> + tristate "Chipone ICN6211 MIPI-DSI/RGB converter bridge"
> + depends on DRM && DRM_PANEL
> + depends on OF
> + select DRM_MIPI_DSI
> + help
> + ICN6211 is MIPI-DSI/RGB converter bridge from chipone.
> + It has a flexible configuration of MIPI DSI signal input
> + and produce RGB565, RGB666, RGB888 output format.
> +
> config DRM_DUMB_VGA_DAC
> tristate "Dumb VGA DAC Bridge support"
> depends on OF
> diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
> index 4934fcf5a6f8..541fdccad10b 100644
> --- a/drivers/gpu/drm/bridge/Makefile
> +++ b/drivers/gpu/drm/bridge/Makefile
> @@ -1,6 +1,7 @@
> # SPDX-License-Identifier: GPL-2.0
> obj-$(CONFIG_DRM_ANALOGIX_ANX78XX) += analogix-anx78xx.o
> obj-$(CONFIG_DRM_CDNS_DSI) += cdns-dsi.o
> +obj-$(CONFIG_DRM_CHIPONE_ICN6211) += chipone-icn6211.o
> obj-$(CONFIG_DRM_DUMB_VGA_DAC) += dumb-vga-dac.o
> obj-$(CONFIG_DRM_LVDS_ENCODER) += lvds-encoder.o
> obj-$(CONFIG_DRM_MEGACHIPS_STDPXXXX_GE_B850V3_FW) += megachips-stdpxxxx-ge-b850v3-fw.o
> diff --git a/drivers/gpu/drm/bridge/chipone-icn6211.c b/drivers/gpu/drm/bridge/chipone-icn6211.c
> new file mode 100644
> index 000000000000..cd2f3505f845
> --- /dev/null
> +++ b/drivers/gpu/drm/bridge/chipone-icn6211.c
> @@ -0,0 +1,275 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (C) 2018 Amarula Solutions
> + * Author: Jagan Teki <jagan at amarulasolutions.com>
> + */
> +
> +#include <drm/drm_atomic_helper.h>
> +#include <drm/drm_fb_helper.h>
> +#include <drm/drm_of.h>
> +#include <drm/drm_panel.h>
> +#include <drm/drm_print.h>
> +#include <drm/drm_probe_helper.h>
> +#include <drm/drm_mipi_dsi.h>
> +
> +#include <linux/delay.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/module.h>
> +#include <linux/of_graph.h>
> +
> +#define ICN6211_INIT_CMD_LEN 2
> +
> +struct chipone {
> + struct device *dev;
> + struct drm_bridge bridge;
> + struct drm_connector connector;
> + struct drm_panel *panel;
> +
> + struct gpio_desc *reset;
> +};
> +
> +static inline struct chipone *bridge_to_chipone(struct drm_bridge *bridge)
> +{
> + return container_of(bridge, struct chipone, bridge);
> +}
> +
> +static inline
> +struct chipone *connector_to_chipone(struct drm_connector *connector)
> +{
> + return container_of(connector, struct chipone, connector);
> +}
> +
> +struct icn6211_init_cmd {
> + u8 data[ICN6211_INIT_CMD_LEN];
> +};
> +
> +static const struct icn6211_init_cmd icn6211_init_cmds[] = {
> + { .data = { 0x7A, 0xC1 } },
> + { .data = { 0x20, 0x20 } },
> + { .data = { 0x21, 0xE0 } },
> + { .data = { 0x22, 0x13 } },
> + { .data = { 0x23, 0x28 } },
> + { .data = { 0x24, 0x30 } },
> + { .data = { 0x25, 0x28 } },
> + { .data = { 0x26, 0x00 } },
> + { .data = { 0x27, 0x0D } },
> + { .data = { 0x28, 0x03 } },
> + { .data = { 0x29, 0x1D } },
> + { .data = { 0x34, 0x80 } },
> + { .data = { 0x36, 0x28 } },
> + { .data = { 0xB5, 0xA0 } },
> + { .data = { 0x5C, 0xFF } },
> + { .data = { 0x2A, 0x01 } },
> + { .data = { 0x56, 0x92 } },
> + { .data = { 0x6B, 0x71 } },
> + { .data = { 0x69, 0x2B } },
> + { .data = { 0x10, 0x40 } },
> + { .data = { 0x11, 0x98 } },
> + { .data = { 0xB6, 0x20 } },
> + { .data = { 0x51, 0x20 } },
> + { .data = { 0x09, 0x10 } },
> +};
What are those commands supposed to be? Some of them at least look
pretty standard (and have proper functions):
MIPI_DCS_EXIT_INVERT_MODE, _SET_DISPLAY_ON, _SET_TEAR_OFF, etc.
> +static int chipone_get_modes(struct drm_connector *connector)
> +{
> + struct chipone *icn = connector_to_chipone(connector);
> +
> + return drm_panel_get_modes(icn->panel);
> +}
> +
> +static const
> +struct drm_connector_helper_funcs chipone_connector_helper_funcs = {
> + .get_modes = chipone_get_modes,
> +};
> +
> +static const struct drm_connector_funcs chipone_connector_funcs = {
> + .fill_modes = drm_helper_probe_single_connector_modes,
> + .destroy = drm_connector_cleanup,
> + .reset = drm_atomic_helper_connector_reset,
> + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
> + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
> +};
> +
> +static void chipone_disable(struct drm_bridge *bridge)
> +{
> + struct chipone *icn = bridge_to_chipone(bridge);
> + int ret = drm_panel_disable(bridge_to_chipone(bridge)->panel);
> +
> + if (ret < 0)
> + DRM_DEV_ERROR(icn->dev, "error disabling panel (%d)\n", ret);
> +}
> +
> +static void chipone_post_disable(struct drm_bridge *bridge)
> +{
> + struct chipone *icn = bridge_to_chipone(bridge);
> + int ret;
> +
> + ret = drm_panel_unprepare(icn->panel);
> + if (ret < 0)
> + DRM_DEV_ERROR(icn->dev, "error unpreparing panel (%d)\n", ret);
> +
> + msleep(50);
> +
> + gpiod_set_value(icn->reset, 0);
> +}
> +
> +static void chipone_pre_enable(struct drm_bridge *bridge)
> +{
> + struct chipone *icn = bridge_to_chipone(bridge);
> + struct mipi_dsi_device *dsi = to_mipi_dsi_device(icn->dev);
> + unsigned int i;
> + int ret;
> +
> + gpiod_set_value(icn->reset, 0);
> + msleep(20);
> +
> + gpiod_set_value(icn->reset, 1);
> + msleep(50);
> +
> + for (i = 0; i < ARRAY_SIZE(icn6211_init_cmds); i++) {
> + const struct icn6211_init_cmd *cmd = &icn6211_init_cmds[i];
> +
> + ret = mipi_dsi_generic_write(dsi, cmd->data,
> + ICN6211_INIT_CMD_LEN);
> + if (ret < 0) {
> + DRM_DEV_ERROR(icn->dev,
> + "failed to write cmd %d: %d\n", i, ret);
> + return;
> + }
> + }
> +
> + ret = drm_panel_prepare(icn->panel);
> + if (ret < 0)
> + DRM_DEV_ERROR(icn->dev, "error preparing panel (%d)\n", ret);
> +}
> +
> +static void chipone_enable(struct drm_bridge *bridge)
> +{
> + struct chipone *icn = bridge_to_chipone(bridge);
> + int ret = drm_panel_enable(icn->panel);
> +
> + if (ret < 0)
> + DRM_DEV_ERROR(icn->dev, "error enabling panel (%d)\n", ret);
> +}
> +
> +static int chipone_attach(struct drm_bridge *bridge)
> +{
> + struct chipone *icn = bridge_to_chipone(bridge);
> + struct drm_device *drm = bridge->dev;
> + int ret;
> +
> + icn->connector.polled = DRM_CONNECTOR_POLL_HPD;
> + ret = drm_connector_init(drm, &icn->connector,
> + &chipone_connector_funcs,
> + DRM_MODE_CONNECTOR_Unknown);
It should be a DRM_MODE_CONNECTOR_DPI connector.
> + if (ret) {
> + DRM_ERROR("Failed to initialize connector\n");
> + return ret;
> + }
> +
> + drm_connector_helper_add(&icn->connector,
> + &chipone_connector_helper_funcs);
> + drm_connector_attach_encoder(&icn->connector, bridge->encoder);
> + drm_panel_attach(icn->panel, &icn->connector);
> + icn->connector.funcs->reset(&icn->connector);
> + drm_fb_helper_add_one_connector(drm->fb_helper, &icn->connector);
What do you need that for?
> + drm_connector_register(&icn->connector);
> +
> + return 0;
> +}
> +
> +static void chipone_detach(struct drm_bridge *bridge)
> +{
> + struct chipone *icn = bridge_to_chipone(bridge);
> + struct drm_device *drm = bridge->dev;
> +
> + drm_connector_unregister(&icn->connector);
> + drm_fb_helper_remove_one_connector(drm->fb_helper, &icn->connector);
> + drm_panel_detach(icn->panel);
> + icn->panel = NULL;
> + drm_connector_put(&icn->connector);
> +}
> +
> +static const struct drm_bridge_funcs chipone_bridge_funcs = {
> + .disable = chipone_disable,
> + .post_disable = chipone_post_disable,
> + .enable = chipone_enable,
> + .pre_enable = chipone_pre_enable,
> + .attach = chipone_attach,
> + .detach = chipone_detach,
> +};
> +
> +static int chipone_probe(struct mipi_dsi_device *dsi)
> +{
> + struct device *dev = &dsi->dev;
> + struct chipone *icn;
> + int ret;
> +
> + icn = devm_kzalloc(dev, sizeof(struct chipone), GFP_KERNEL);
> + if (!icn)
> + return -ENOMEM;
> +
> + mipi_dsi_set_drvdata(dsi, icn);
> +
> + icn->dev = dev;
> + dsi->lanes = 4;
> + dsi->format = MIPI_DSI_FMT_RGB888;
> + dsi->mode_flags = MIPI_DSI_MODE_VIDEO_SYNC_PULSE;
> +
> + icn->reset = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
> + if (IS_ERR(icn->reset)) {
> + DRM_DEV_ERROR(dev, "no reset GPIO pin provided\n");
> + return PTR_ERR(icn->reset);
> + }
> +
> + ret = drm_of_find_panel_or_bridge(icn->dev->of_node, 1, 0,
> + &icn->panel, NULL);
> + if (ret && ret != -EPROBE_DEFER) {
> + DRM_DEV_ERROR(dev, "failed to find panel (ret = %d)\n", ret);
> + return ret;
> + }
> +
> + icn->bridge.funcs = &chipone_bridge_funcs;
> + icn->bridge.of_node = dev->of_node;
> +
> + drm_bridge_add(&icn->bridge);
> +
> + ret = mipi_dsi_attach(dsi);
> + if (ret < 0) {
> + drm_bridge_remove(&icn->bridge);
> + DRM_DEV_ERROR(dev, "failed to attach dsi (ret = %d)\n", ret);
> + }
> +
> + return ret;
> +}
> +
> +static int chipone_remove(struct mipi_dsi_device *dsi)
> +{
> + struct chipone *icn = mipi_dsi_get_drvdata(dsi);
> +
> + mipi_dsi_detach(dsi);
> + drm_bridge_remove(&icn->bridge);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id chipone_of_match[] = {
> + { .compatible = "bananapi,icn6211" },
This should have your generic compatible listed
Maxime
--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 228 bytes
Desc: not available
URL: <https://lists.freedesktop.org/archives/dri-devel/attachments/20190315/aa4f76b9/attachment.sig>
More information about the dri-devel
mailing list