[DO NOT MERGE] [PATCH v9 8/9] arm64: dts: allwinner: a64-pine64-lts: Enable Feiyang FY07024DI26A30-D DSI panel

[Jagan Teki]

Feiyang FY07024DI26A30-D MIPI_DSI panel is desiged to attach with
DSI connector on pine64 boards, enable the same for pine64 LTS.

DSI panel connected via board DSI port with,
- DLDO1 as VCC-DSI supply
- DC1SW as AVDD supply
- DLDO2 as DVDD supply
- PD24 gpio for reset pin
- PH10 gpio for backlight enable pin

Tested-by: Merlijn Wajer <merlijn at wizzup.org>
Signed-off-by: Jagan Teki <jagan at amarulasolutions.com>
---
 .../allwinner/sun50i-a64-sopine-baseboard.dts | 31 +++++++++++++++++++
 1 file changed, 31 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts
index e6fb9683f213..51b0cf71c3d4 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts
@@ -46,6 +46,7 @@
 /dts-v1/;
 
 #include "sun50i-a64-sopine.dtsi"
+#include <dt-bindings/pwm/pwm.h>
 
 / {
 	model = "SoPine with baseboard";
@@ -61,6 +62,14 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&r_pwm 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <1 2 4 8 16 32 64 128 255>;
+		default-brightness-level = <8>;
+		enable-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* LCD-BL-EN: PH10 */
+	};
+
 	hdmi-connector {
 		compatible = "hdmi-connector";
 		type = "a";
@@ -104,6 +113,24 @@
 	status = "okay";
 };
 
+&dphy {
+	status = "okay";
+};
+
+&dsi {
+	vcc-dsi-supply = <&reg_dldo1>;		/* VCC-DSI */
+	status = "okay";
+
+	panel at 0 {
+		compatible = "feiyang,fy07024di26a30d";
+		reg = <0>;
+		avdd-supply = <&reg_dc1sw>;	/* VCC-LCD */
+		dvdd-supply = <&reg_dldo2>;	/* VCC-MIPI */
+		reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* LCD-RST: PD24 */
+		backlight = <&backlight>;
+	};
+};
+
 &ehci0 {
 	status = "okay";
 };
@@ -184,6 +211,10 @@
 	vcc-hdmi-supply = <&reg_dldo1>;
 };
 
+&r_pwm {
+	status = "okay";
+};
+
 &sound {
 	simple-audio-card,aux-devs = <&codec_analog>;
 	simple-audio-card,widgets = "Microphone", "Microphone Jack",
-- 
2.18.0.321.gffc6fa0e3