[PATCH v11 7/7] ARM: dts: sun8i: bananapi-m2m: Enable Bananapi S070WV20-CT16 DSI panel

[Jagan Teki]

This patch add support for Bananapi S070WV20-CT16 DSI panel to
BPI-M2M board.

DSI panel connected via board DSI port with,
- DCDC1 as VCC-DSI supply
- DLDO1 as VDD supply
- PL5 gpio for lcd reset gpio pin
- PB7 gpio for lcd enable gpio pin
- PL4 gpio for backlight enable pin

Signed-off-by: Jagan Teki <jagan at amarulasolutions.com>
---
 arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts | 40 ++++++++++++++++++++
 1 file changed, 40 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts b/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts
index e1c75f7fa3ca..4e71e81d2bad 100644
--- a/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts
+++ b/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts
@@ -44,6 +44,7 @@
 #include "sun8i-a33.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>
 
 / {
 	model = "BananaPi M2 Magic";
@@ -61,6 +62,14 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <1 2 4 8 16 32 64 128 255>;
+		default-brightness-level = <8>;
+		enable-gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* LCD-BL-EN: PL4 */
+	};
+
 	leds {
 		compatible = "gpio-leds";
 
@@ -122,6 +131,27 @@
 	status = "okay";
 };
 
+&de {
+	status = "okay";
+};
+
+&dphy {
+	status = "okay";
+};
+
+&dsi {
+	vcc-dsi-supply = <&reg_dcdc1>;		/* VCC3V3-DSI */
+	status = "okay";
+
+	panel at 0 {
+		compatible = "bananapi,s070wv20-ct16-icn6211";
+		reg = <0>;
+		enable-gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>; /* LCD-PWR-EN: PB7 */
+		reset-gpios = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* LCD-RST: PL5 */
+		backlight = <&backlight>;
+	};
+};
+
 &ehci0 {
 	status = "okay";
 };
@@ -157,6 +187,12 @@
 	status = "okay";
 };
 
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_pin>;
+	status = "okay";
+};
+
 &r_rsb {
 	status = "okay";
 
@@ -269,6 +305,10 @@
 	status = "okay";
 };
 
+&tcon0 {
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pb_pins>;
-- 
2.18.0.321.gffc6fa0e3