[PATCH v4 04/14] drm/mxsfb: Reset vital registers for a proper initialization

Stefan Agner stefan at agner.ch
Mon Oct 14 12:59:05 UTC 2019


On 2019-08-29 13:30, Robert Chiras wrote:
> Some of the registers, like LCDC_CTRL, CTRL2_OUTSTANDING_REQS and
> CTRL1_RECOVERY_ON_UNDERFLOW needs to be properly cleared/initialized
> for a better start and stop routine.


This patch uses CTRL2_OUTSTANDING_REQS which is only introduced in the
next patch. This breaks bisectability.

--
Stefan

> 
> Signed-off-by: Robert Chiras <robert.chiras at nxp.com>
> Tested-by: Guido G√ľnther <agx at sigxcpu.org>
> ---
>  drivers/gpu/drm/mxsfb/mxsfb_crtc.c | 12 ++++++++++++
>  1 file changed, 12 insertions(+)
> 
> diff --git a/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
> b/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
> index b69ace8..5e44f57 100644
> --- a/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
> +++ b/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
> @@ -127,6 +127,10 @@ static void mxsfb_enable_controller(struct
> mxsfb_drm_private *mxsfb)
>  		clk_prepare_enable(mxsfb->clk_disp_axi);
>  	clk_prepare_enable(mxsfb->clk);
>  
> +	if (mxsfb->devdata->ipversion >= 4)
> +		writel(CTRL2_OUTSTANDING_REQS(REQ_16),
> +		       mxsfb->base + LCDC_V4_CTRL2 + REG_SET);
> +
>  	/* If it was disabled, re-enable the mode again */
>  	writel(CTRL_DOTCLK_MODE, mxsfb->base + LCDC_CTRL + REG_SET);
>  
> @@ -136,12 +140,19 @@ static void mxsfb_enable_controller(struct
> mxsfb_drm_private *mxsfb)
>  	writel(reg, mxsfb->base + LCDC_VDCTRL4);
>  
>  	writel(CTRL_RUN, mxsfb->base + LCDC_CTRL + REG_SET);
> +	writel(CTRL1_RECOVERY_ON_UNDERFLOW, mxsfb->base + LCDC_CTRL1 + REG_SET);
>  }
>  
>  static void mxsfb_disable_controller(struct mxsfb_drm_private *mxsfb)
>  {
>  	u32 reg;
>  
> +	if (mxsfb->devdata->ipversion >= 4)
> +		writel(CTRL2_OUTSTANDING_REQS(0x7),
> +		       mxsfb->base + LCDC_V4_CTRL2 + REG_CLR);
> +
> +	writel(CTRL_RUN, mxsfb->base + LCDC_CTRL + REG_CLR);
> +
>  	/*
>  	 * Even if we disable the controller here, it will still continue
>  	 * until its FIFOs are running out of data
> @@ -295,6 +306,7 @@ void mxsfb_crtc_enable(struct mxsfb_drm_private *mxsfb)
>  	dma_addr_t paddr;
>  
>  	mxsfb_enable_axi_clk(mxsfb);
> +	writel(0, mxsfb->base + LCDC_CTRL);
>  	mxsfb_crtc_mode_set_nofb(mxsfb);
>  
>  	/* Write cur_buf as well to avoid an initial corrupt frame */


More information about the dri-devel mailing list