[PATCH v3 2/2] drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP bridge driver

Xin Ji xji at analogixsemi.com
Tue Oct 15 09:49:01 UTC 2019


The ANX7625 is an ultra-low power 4K Mobile HD Transmitter designed
for portable device. It converts MIPI DSI/DPI to DisplayPort 1.3 4K.

The ANX7625 can support both USB Type-C PD feature and MIPI DSI/DPI
to DP feature. This driver only enabled MIPI DSI/DPI to DP feature.

Signed-off-by: Xin Ji <xji at analogixsemi.com>
---
 drivers/gpu/drm/bridge/Makefile           |    2 +-
 drivers/gpu/drm/bridge/analogix/Kconfig   |    6 +
 drivers/gpu/drm/bridge/analogix/Makefile  |    1 +
 drivers/gpu/drm/bridge/analogix/anx7625.c | 2043 +++++++++++++++++++++++++++++
 drivers/gpu/drm/bridge/analogix/anx7625.h |  406 ++++++
 5 files changed, 2457 insertions(+), 1 deletion(-)
 create mode 100644 drivers/gpu/drm/bridge/analogix/anx7625.c
 create mode 100644 drivers/gpu/drm/bridge/analogix/anx7625.h

diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
index 4934fcf..bcd388a 100644
--- a/drivers/gpu/drm/bridge/Makefile
+++ b/drivers/gpu/drm/bridge/Makefile
@@ -12,8 +12,8 @@ obj-$(CONFIG_DRM_SII9234) += sii9234.o
 obj-$(CONFIG_DRM_THINE_THC63LVD1024) += thc63lvd1024.o
 obj-$(CONFIG_DRM_TOSHIBA_TC358764) += tc358764.o
 obj-$(CONFIG_DRM_TOSHIBA_TC358767) += tc358767.o
-obj-$(CONFIG_DRM_ANALOGIX_DP) += analogix/
 obj-$(CONFIG_DRM_I2C_ADV7511) += adv7511/
 obj-$(CONFIG_DRM_TI_SN65DSI86) += ti-sn65dsi86.o
 obj-$(CONFIG_DRM_TI_TFP410) += ti-tfp410.o
+obj-y += analogix/
 obj-y += synopsys/
diff --git a/drivers/gpu/drm/bridge/analogix/Kconfig b/drivers/gpu/drm/bridge/analogix/Kconfig
index e930ff9..b2f127e 100644
--- a/drivers/gpu/drm/bridge/analogix/Kconfig
+++ b/drivers/gpu/drm/bridge/analogix/Kconfig
@@ -2,3 +2,9 @@
 config DRM_ANALOGIX_DP
 	tristate
 	depends on DRM
+
+config ANALOGIX_ANX7625
+	tristate "Analogix MIPI to DP interface support"
+	help
+		ANX7625 is an ultra-low power 4K mobile HD transmitter designed
+		for portable devices. It converts MIPI/DPI to DisplayPort1.3 4K.
diff --git a/drivers/gpu/drm/bridge/analogix/Makefile b/drivers/gpu/drm/bridge/analogix/Makefile
index fdbf3fd..8a52867 100644
--- a/drivers/gpu/drm/bridge/analogix/Makefile
+++ b/drivers/gpu/drm/bridge/analogix/Makefile
@@ -1,3 +1,4 @@
 # SPDX-License-Identifier: GPL-2.0-only
+obj-$(CONFIG_ANALOGIX_ANX7625) += anx7625.o
 analogix_dp-objs := analogix_dp_core.o analogix_dp_reg.o
 obj-$(CONFIG_DRM_ANALOGIX_DP) += analogix_dp.o
diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.c b/drivers/gpu/drm/bridge/analogix/anx7625.c
new file mode 100644
index 0000000..456b95c
--- /dev/null
+++ b/drivers/gpu/drm/bridge/analogix/anx7625.c
@@ -0,0 +1,2043 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright(c) 2016, Analogix Semiconductor. All rights reserved.
+ *
+ */
+#include <linux/extcon.h>
+#include <linux/gcd.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/workqueue.h>
+
+#include <linux/of_gpio.h>
+#include <linux/of_graph.h>
+#include <linux/of_platform.h>
+
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_bridge.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_dp_helper.h>
+#include <drm/drm_edid.h>
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_panel.h>
+#include <drm/drm_print.h>
+#include <drm/drm_probe_helper.h>
+
+#include <video/display_timing.h>
+
+#include "anx7625.h"
+
+/*
+ * there is a sync issue while access I2C register between AP(CPU) and
+ * internal firmware(OCM), to avoid the race condition, AP should access
+ * the reserved slave address before slave address occurs changes.
+ */
+static int i2c_access_workaround(struct anx7625_data *ctx,
+				 struct i2c_client *client)
+{
+	u8 offset;
+	struct device *dev = &client->dev;
+	int ret;
+
+	if (client == ctx->last_client)
+		return 0;
+
+	ctx->last_client = client;
+
+	if (client == ctx->i2c.tcpc_client)
+		offset = RSVD_00_ADDR;
+	else if (client == ctx->i2c.tx_p0_client)
+		offset = RSVD_D1_ADDR;
+	else if (client == ctx->i2c.tx_p1_client)
+		offset = RSVD_60_ADDR;
+	else if (client == ctx->i2c.rx_p0_client)
+		offset = RSVD_39_ADDR;
+	else if (client == ctx->i2c.rx_p1_client)
+		offset = RSVD_7F_ADDR;
+	else
+		offset = RSVD_00_ADDR;
+
+	ret = i2c_smbus_write_byte_data(client, offset, 0x00);
+	if (ret < 0)
+		DRM_DEV_ERROR(dev,
+			      "failed to access i2c id=%x\n:%x",
+			      client->addr, offset);
+
+	return ret;
+}
+
+static int anx7625_reg_read(struct anx7625_data *ctx,
+			    struct i2c_client *client, u8 reg_addr)
+{
+	int ret;
+	struct device *dev = &client->dev;
+
+	i2c_access_workaround(ctx, client);
+
+	ret = i2c_smbus_read_byte_data(client, reg_addr);
+	if (ret < 0)
+		DRM_DEV_ERROR(dev, "read i2c failed id=%x:%x\n",
+			      client->addr, reg_addr);
+
+	return ret;
+}
+
+static int anx7625_reg_block_read(struct anx7625_data *ctx,
+				  struct i2c_client *client,
+				  u8 reg_addr, u8 len, u8 *buf)
+{
+	int ret;
+	struct device *dev = &client->dev;
+
+	i2c_access_workaround(ctx, client);
+
+	ret = i2c_smbus_read_i2c_block_data(client, reg_addr, len, buf);
+	if (ret < 0)
+		DRM_DEV_ERROR(dev, "read i2c block failed id=%x:%x\n",
+			      client->addr, reg_addr);
+
+	return ret;
+}
+
+static int anx7625_reg_write(struct anx7625_data *ctx,
+			     struct i2c_client *client,
+			     u8 reg_addr, u8 reg_val)
+{
+	int ret;
+	struct device *dev = &client->dev;
+
+	i2c_access_workaround(ctx, client);
+
+	ret = i2c_smbus_write_byte_data(client, reg_addr, reg_val);
+
+	if (ret < 0)
+		DRM_DEV_ERROR(dev, "failed to write i2c id=%x\n:%x",
+			      client->addr, reg_addr);
+
+	return ret;
+}
+
+static int anx7625_write_or(struct anx7625_data *ctx,
+			    struct i2c_client *client,
+			    u8 offset, u8 mask)
+{
+	int val;
+
+	val = anx7625_reg_read(ctx, client, offset);
+	if (val < 0)
+		return val;
+
+	return anx7625_reg_write(ctx, client, offset, (val | (mask)));
+}
+
+static int anx7625_write_and(struct anx7625_data *ctx,
+			     struct i2c_client *client,
+			     u8 offset, u8 mask)
+{
+	int val;
+
+	val = anx7625_reg_read(ctx, client, offset);
+	if (val < 0)
+		return val;
+
+	return anx7625_reg_write(ctx, client, offset, (val & (mask)));
+}
+
+static int anx7625_write_and_or(struct anx7625_data *ctx,
+				struct i2c_client *client,
+				u8 offset, u8 and_mask, u8 or_mask)
+{
+	int val;
+
+	val = anx7625_reg_read(ctx, client, offset);
+	if (val < 0)
+		return val;
+
+	return anx7625_reg_write(ctx, client,
+				 offset, (val & and_mask) | (or_mask));
+}
+
+static int anx7625_config_bit_matrix(struct anx7625_data *ctx)
+{
+	int i, ret;
+
+	ret = anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
+				AUDIO_CONTROL_REGISTER, 0x80);
+	for (i = 0; i < 13; i++)
+		ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
+					 VIDEO_BIT_MATRIX_12 + i,
+					 0x18 + i);
+
+	return ret;
+}
+
+static int anx7625_read_ctrl_status_p0(struct anx7625_data *ctx)
+{
+	return anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, AP_AUX_CTRL_STATUS);
+}
+
+static int wait_aux_op_finish(struct anx7625_data *ctx)
+{
+	int val;
+	int ret;
+	struct device *dev = &ctx->client->dev;
+
+	ret = readx_poll_timeout(anx7625_read_ctrl_status_p0,
+				 ctx, val,
+				 (!(val & AP_AUX_CTRL_OP_EN) || (val < 0)),
+				 2000,
+				 2000 * 150);
+	if (ret) {
+		DRM_DEV_ERROR(dev, "aux operation failed!\n");
+		return -EIO;
+	}
+
+	val = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client,
+			       AP_AUX_CTRL_STATUS);
+	if (val < 0 || (val & 0x0F)) {
+		DRM_DEV_ERROR(dev, "aux status %02x\n", val);
+		val = -EIO;
+	}
+
+	return val;
+}
+
+static int anx7625_video_mute_control(struct anx7625_data *ctx,
+				      u8 status)
+{
+	int ret;
+
+	if (status) { /* mute on */
+		/* set mute flag */
+		ret = anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
+				       AP_AV_STATUS, AP_MIPI_MUTE);
+		/* clear mipi RX en */
+		ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
+					 AP_AV_STATUS, (u8)~AP_MIPI_RX_EN);
+	} else { /* mute off */
+		/* clear mute flag */
+		ret = anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
+					AP_AV_STATUS, (u8)~AP_MIPI_MUTE);
+		/* set MIPI RX EN */
+		ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
+					AP_AV_STATUS, AP_MIPI_RX_EN);
+	}
+
+	return ret;
+}
+
+static int anx7625_config_audio_input(struct anx7625_data *ctx)
+{
+	int ret;
+
+	/* channel num */
+	ret = anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
+				AUDIO_CHANNEL_STATUS_6, I2S_CH_2 << 5);
+	/* layout */
+	/* as I2S channel is 2, no need to set layout */
+
+	/* FS */
+	ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client,
+				    AUDIO_CHANNEL_STATUS_4,
+				    0xf0, AUDIO_FS_48K);
+	/* word length */
+	ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client,
+				    AUDIO_CHANNEL_STATUS_5,
+				    0xf0, AUDIO_W_LEN_24_24MAX);
+	/* I2S */
+	ret |= anx7625_write_or(ctx, ctx->i2c.tx_p2_client,
+				AUDIO_CHANNEL_STATUS_6, I2S_SLAVE_MODE);
+	ret |= anx7625_write_and(ctx, ctx->i2c.tx_p2_client,
+				 AUDIO_CONTROL_REGISTER, ~TDM_TIMING_MODE);
+	/* audio change flag */
+	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
+				AP_AV_STATUS, AP_AUDIO_CHG);
+
+	if (ret < 0)
+		DRM_ERROR("failed to config audio.\n");
+
+	return ret;
+}
+
+/* reduction of fraction a/b */
+static void anx7625_reduction_of_a_fraction(unsigned long *a, unsigned long *b)
+{
+	unsigned long gcd_num;
+	unsigned long tmp_a, tmp_b;
+	u32 i = 1;
+
+	gcd_num = gcd(*a, *b);
+	*a /= gcd_num;
+	*b /= gcd_num;
+
+	tmp_a = *a;
+	tmp_b = *b;
+
+	while ((*a > MAX_UNSIGNED_24BIT) || (*b > MAX_UNSIGNED_24BIT)) {
+		i++;
+		*a = tmp_a / i;
+		*b = tmp_b / i;
+	}
+
+	/*
+	 * in the end, make a, b larger to have higher ODFC PLL
+	 * output frequency accuracy
+	 */
+	while ((*a < MAX_UNSIGNED_24BIT) && (*b < MAX_UNSIGNED_24BIT)) {
+		*a <<= 1;
+		*b <<= 1;
+	}
+
+	*a >>= 1;
+	*b >>= 1;
+}
+
+static int anx7625_calculate_m_n(u32 pixelclock,
+				 unsigned long *m,
+				 unsigned long *n,
+				 u8 *post_divider)
+{
+	if (pixelclock > PLL_OUT_FREQ_ABS_MAX / POST_DIVIDER_MIN) {
+		/* pixel clock frequency is too high */
+		DRM_ERROR("pixelclock too high, act(%d), maximum(%lu)\n",
+			  pixelclock,
+			  PLL_OUT_FREQ_ABS_MAX / POST_DIVIDER_MIN);
+		return -EINVAL;
+	}
+
+	if (pixelclock < PLL_OUT_FREQ_ABS_MIN / POST_DIVIDER_MAX) {
+		/* pixel clock frequency is too low */
+		DRM_ERROR("pixelclock too low, act(%d), maximum(%lu)\n",
+			  pixelclock,
+			  PLL_OUT_FREQ_ABS_MIN / POST_DIVIDER_MAX);
+		return -EINVAL;
+	}
+
+	for (*post_divider = 1;
+		pixelclock < (PLL_OUT_FREQ_MIN / (*post_divider));)
+		*post_divider += 1;
+
+	if (*post_divider > POST_DIVIDER_MAX) {
+		for (*post_divider = 1;
+			(pixelclock <
+			 (PLL_OUT_FREQ_ABS_MIN / (*post_divider)));)
+			*post_divider += 1;
+
+		if (*post_divider > POST_DIVIDER_MAX) {
+			DRM_ERROR("cannot find property post_divider(%d)\n",
+				  *post_divider);
+			return -EDOM;
+		}
+	}
+
+	/* patch to improve the accuracy */
+	if (*post_divider == 7) {
+		/* 27,000,000 is not divisible by 7 */
+		*post_divider = 8;
+	} else if (*post_divider == 11) {
+		/* 27,000,000 is not divisible by 11 */
+		*post_divider = 12;
+	} else if ((*post_divider == 13) || (*post_divider == 14)) {
+		/*27,000,000 is not divisible by 13 or 14*/
+		*post_divider = 15;
+	}
+
+	if (pixelclock * (*post_divider) > PLL_OUT_FREQ_ABS_MAX) {
+		DRM_ERROR("act clock(%u) large than maximum(%lu)\n",
+			  pixelclock * (*post_divider),
+			  PLL_OUT_FREQ_ABS_MAX);
+		return -EDOM;
+	}
+
+	*m = pixelclock;
+	*n = XTAL_FRQ / (*post_divider);
+
+	anx7625_reduction_of_a_fraction(m, n);
+
+	return 0;
+}
+
+static int anx7625_odfc_config(struct anx7625_data *ctx,
+			       u8 post_divider)
+{
+	int ret;
+
+	/* config input reference clock frequency 27MHz/19.2MHz */
+	ret = anx7625_write_and(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_16,
+				~(REF_CLK_27000KHZ << MIPI_FREF_D_IND));
+	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_16,
+				(REF_CLK_27000KHZ << MIPI_FREF_D_IND));
+	/* post divider */
+	ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client,
+				 MIPI_DIGITAL_PLL_8, 0x0f);
+	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_8,
+				post_divider << 4);
+
+	/* add patch for MIS2-125 (5pcs ANX7625 fail ATE MBIST test) */
+	ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_7,
+				 ~MIPI_PLL_VCO_TUNE_REG_VAL);
+
+	/* reset ODFC PLL */
+	ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_7,
+				 ~MIPI_PLL_RESET_N);
+	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_7,
+				MIPI_PLL_RESET_N);
+
+	if (ret < 0)
+		DRM_ERROR("IO error.\n");
+
+	return ret;
+}
+
+static int anx7625_dsi_video_timing_config(struct anx7625_data *ctx)
+{
+	struct device *dev = &ctx->client->dev;
+	unsigned long m, n;
+	u16 htotal;
+	int ret;
+	u8 post_divider = 0;
+
+	ret = anx7625_calculate_m_n(ctx->dt.pixelclock.min * 1000,
+				    &m, &n, &post_divider);
+
+	if (ret) {
+		DRM_ERROR("cannot get property m n value.\n");
+		return ret;
+	}
+
+	DRM_DEV_DEBUG_DRIVER(dev, "compute M(%lu), N(%lu), divider(%d).\n",
+			     m, n, post_divider);
+
+	/* configure pixel clock */
+	ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, PIXEL_CLOCK_L,
+				(ctx->dt.pixelclock.min / 1000) & 0xFF);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, PIXEL_CLOCK_H,
+				 (ctx->dt.pixelclock.min / 1000) >> 8);
+	/* lane count */
+	ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client,
+			MIPI_LANE_CTRL_0, 0xfc);
+	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client,
+				MIPI_LANE_CTRL_0, 3);
+
+	/* Htotal */
+	htotal = ctx->dt.hactive.min + ctx->dt.hfront_porch.min +
+		ctx->dt.hback_porch.min + ctx->dt.hsync_len.min;
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+			HORIZONTAL_TOTAL_PIXELS_L, htotal & 0xFF);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+			HORIZONTAL_TOTAL_PIXELS_H, htotal >> 8);
+	/* Hactive */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+			HORIZONTAL_ACTIVE_PIXELS_L, ctx->dt.hactive.min & 0xFF);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+			HORIZONTAL_ACTIVE_PIXELS_H, ctx->dt.hactive.min >> 8);
+	/* HFP */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+			HORIZONTAL_FRONT_PORCH_L, ctx->dt.hfront_porch.min);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+			HORIZONTAL_FRONT_PORCH_H,
+			ctx->dt.hfront_porch.min >> 8);
+	/* HWS */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+			HORIZONTAL_SYNC_WIDTH_L, ctx->dt.hsync_len.min);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+			HORIZONTAL_SYNC_WIDTH_H, ctx->dt.hsync_len.min >> 8);
+	/* HBP */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+			HORIZONTAL_BACK_PORCH_L, ctx->dt.hback_porch.min);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+			HORIZONTAL_BACK_PORCH_H, ctx->dt.hback_porch.min >> 8);
+	/* Vactive */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, ACTIVE_LINES_L,
+			ctx->dt.vactive.min);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, ACTIVE_LINES_H,
+			ctx->dt.vactive.min >> 8);
+	/* VFP */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+			VERTICAL_FRONT_PORCH, ctx->dt.vfront_porch.min);
+	/* VWS */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+			VERTICAL_SYNC_WIDTH, ctx->dt.vsync_len.min);
+	/* VBP */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+			VERTICAL_BACK_PORCH, ctx->dt.vback_porch.min);
+	/* M value */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+			MIPI_PLL_M_NUM_23_16, (m >> 16) & 0xff);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+			MIPI_PLL_M_NUM_15_8, (m >> 8) & 0xff);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+			MIPI_PLL_M_NUM_7_0, (m & 0xff));
+	/* N value */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+			MIPI_PLL_N_NUM_23_16, (n >> 16) & 0xff);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+			MIPI_PLL_N_NUM_15_8, (n >> 8) & 0xff);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, MIPI_PLL_N_NUM_7_0,
+			(n & 0xff));
+	/* diff */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+			MIPI_DIGITAL_ADJ_1, 0x37);
+
+	ret |= anx7625_odfc_config(ctx, post_divider - 1);
+
+	if (ret < 0)
+		DRM_ERROR("mipi dsi setup IO error.\n");
+
+	return ret;
+}
+
+static int anx7625_swap_dsi_lane3(struct anx7625_data *ctx)
+{
+	int val;
+
+	/* swap MIPI-DSI data lane 3 P and N */
+	val = anx7625_reg_read(ctx, ctx->i2c.rx_p1_client, MIPI_SWAP);
+	if (val < 0) {
+		DRM_ERROR("IO error : access MIPI_SWAP.\n");
+		return -EIO;
+	}
+
+	val |= (1 << MIPI_SWAP_CH3);
+	return anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, MIPI_SWAP, val);
+}
+
+static int anx7625_api_dsi_config(struct anx7625_data *ctx)
+
+{
+	int val, ret;
+
+	/* swap MIPI-DSI data lane 3 P and N */
+	ret = anx7625_swap_dsi_lane3(ctx);
+	if (ret < 0) {
+		DRM_ERROR("IO error : swap dsi lane 3 failed.\n");
+		return ret;
+	}
+
+	/* DSI clock settings */
+	val = (0 << MIPI_HS_PWD_CLK)		|
+		(0 << MIPI_HS_RT_CLK)		|
+		(0 << MIPI_PD_CLK)		|
+		(1 << MIPI_CLK_RT_MANUAL_PD_EN)	|
+		(1 << MIPI_CLK_HS_MANUAL_PD_EN)	|
+		(0 << MIPI_CLK_DET_DET_BYPASS)	|
+		(0 << MIPI_CLK_MISS_CTRL)	|
+		(0 << MIPI_PD_LPTX_CH_MANUAL_PD_EN);
+	ret = anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+				MIPI_PHY_CONTROL_3, val);
+
+	/*
+	 * Decreased HS prepare timing delay from 160ns to 80ns work with
+	 *     a) Dragon board 810 series (Qualcomm AP)
+	 *     b) Moving Pixel DSI source (PG3A pattern generator +
+	 *	P332 D-PHY Probe) default D-PHY timing
+	 *	5ns/step
+	 */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+				 MIPI_TIME_HS_PRPR, 0x10);
+
+	/* enable DSI mode*/
+	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_18,
+				SELECT_DSI << MIPI_DPI_SELECT);
+
+	ret |= anx7625_dsi_video_timing_config(ctx);
+	if (ret < 0) {
+		DRM_ERROR("dsi video timing config failed\n");
+		return ret;
+	}
+
+	/* toggle m, n ready */
+	ret = anx7625_write_and(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_6,
+				~(MIPI_M_NUM_READY | MIPI_N_NUM_READY));
+	usleep_range(1000, 1100);
+	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_6,
+				MIPI_M_NUM_READY | MIPI_N_NUM_READY);
+
+	/* configure integer stable register */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+				 MIPI_VIDEO_STABLE_CNT, 0x02);
+	/* power on MIPI RX */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+				 MIPI_LANE_CTRL_10, 0x00);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+				 MIPI_LANE_CTRL_10, 0x80);
+
+	if (ret < 0)
+		DRM_ERROR("IO error : mipi dsi enable init failed.\n");
+
+	return ret;
+}
+
+static int anx7625_dsi_config(struct anx7625_data *ctx)
+{
+	struct device *dev = &ctx->client->dev;
+	int ret;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "config dsi.\n");
+
+	/* DSC disable */
+	ret = anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
+				R_DSC_CTRL_0, ~DSC_EN);
+
+	ret |= anx7625_api_dsi_config(ctx);
+
+	if (ret < 0) {
+		DRM_ERROR("IO error : api dsi config error.\n");
+		return ret;
+	}
+
+	/* set MIPI RX EN */
+	ret = anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
+			       AP_AV_STATUS, AP_MIPI_RX_EN);
+	/* clear mute flag */
+	ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
+				 AP_AV_STATUS, (u8)~AP_MIPI_MUTE);
+	if (ret < 0)
+		DRM_ERROR("IO error : enable mipi rx failed.\n");
+	else
+		DRM_DEV_DEBUG_DRIVER(dev, "success to config DSI\n");
+
+	return ret;
+}
+
+static int anx7625_api_dpi_config(struct anx7625_data *ctx)
+{
+	u16 freq = ctx->dt.pixelclock.min / 1000;
+	int ret;
+
+	/* configure pixel clock */
+	ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				PIXEL_CLOCK_L, freq & 0xFF);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				 PIXEL_CLOCK_H, (freq >> 8));
+
+	/* set DPI mode */
+	/* set to DPI PLL module sel */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+				 MIPI_DIGITAL_PLL_9, 0x20);
+	/* power down MIPI */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+				 MIPI_LANE_CTRL_10, 0x08);
+	/* enable DPI mode */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+				 MIPI_DIGITAL_PLL_18, 0x1C);
+	/* set first edge */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
+				 VIDEO_CONTROL_0, 0x05);
+	if (ret < 0)
+		DRM_ERROR("IO error : dpi phy set failed.\n");
+
+	return ret;
+}
+
+static int anx7625_dpi_config(struct anx7625_data *ctx)
+{
+	struct device *dev = &ctx->client->dev;
+	int ret;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "config dpi\n");
+
+	/* DSC disable */
+	ret = anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
+				R_DSC_CTRL_0, ~DSC_EN);
+	if (ret < 0) {
+		DRM_ERROR("IO error : disable dsc failed.\n");
+		return ret;
+	}
+
+	ret = anx7625_config_bit_matrix(ctx);
+	if (ret < 0) {
+		DRM_ERROR("config bit matrix failed.\n");
+		return ret;
+	}
+
+	ret = anx7625_api_dpi_config(ctx);
+	if (ret < 0) {
+		DRM_ERROR("mipi phy(dpi) setup failed.\n");
+		return ret;
+	}
+
+	/* set MIPI RX EN */
+	ret = anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
+			       AP_AV_STATUS, AP_MIPI_RX_EN);
+	/* clear mute flag */
+	ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
+				 AP_AV_STATUS, (u8)~AP_MIPI_MUTE);
+	if (ret < 0)
+		DRM_ERROR("IO error : enable mipi rx failed.\n");
+
+	return ret;
+}
+
+static void anx7625_dp_start(struct anx7625_data *ctx)
+{
+	int ret;
+
+	if (!ctx->display_timing_valid) {
+		DRM_ERROR("mipi drm haven't set display timing yet.\n");
+		return;
+	}
+
+	anx7625_config_audio_input(ctx);
+
+	if (ctx->pdata.dsi_supported)
+		ret = anx7625_dsi_config(ctx);
+	else
+		ret = anx7625_dpi_config(ctx);
+
+	if (ret < 0)
+		DRM_ERROR("MIPI phy setup error.\n");
+}
+
+static void anx7625_dp_stop(struct anx7625_data *ctx)
+{
+	struct device *dev = &ctx->client->dev;
+	int ret;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "stop dp output\n");
+
+	/*
+	 * video disable: 0x72:08 bit 7 = 0;
+	 * audio disable: 0x70:87 bit 0 = 0;
+	 */
+	ret = anx7625_write_and(ctx, ctx->i2c.tx_p0_client, 0x87, 0xfe);
+	ret |= anx7625_write_and(ctx, ctx->i2c.tx_p2_client, 0x08, 0x7f);
+
+	ret |= anx7625_video_mute_control(ctx, 1);
+	if (ret < 0)
+		DRM_ERROR("IO error : mute video failed\n");
+}
+
+static int sp_tx_rst_aux(struct anx7625_data *ctx)
+{
+	int ret;
+
+	ret = anx7625_write_or(ctx, ctx->i2c.tx_p2_client, RST_CTRL2,
+			       AUX_RST);
+	ret |= anx7625_write_and(ctx, ctx->i2c.tx_p2_client, RST_CTRL2,
+				 ~AUX_RST);
+	return ret;
+}
+
+static int sp_tx_aux_wr(struct anx7625_data *ctx, u8 offset)
+{
+	int ret;
+
+	ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				AP_AUX_BUFF_START, offset);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				 AP_AUX_COMMAND, 0x04);
+	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
+				AP_AUX_CTRL_STATUS, AP_AUX_CTRL_OP_EN);
+	return (ret | wait_aux_op_finish(ctx));
+}
+
+static int sp_tx_aux_rd(struct anx7625_data *ctx, u8 len_cmd)
+{
+	int ret;
+
+	ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				AP_AUX_COMMAND, len_cmd);
+	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
+				AP_AUX_CTRL_STATUS, AP_AUX_CTRL_OP_EN);
+	return (ret | wait_aux_op_finish(ctx));
+}
+
+static int sp_tx_get_edid_block(struct anx7625_data *ctx)
+{
+	int c = 0;
+	struct device *dev = &ctx->client->dev;
+
+	sp_tx_aux_wr(ctx, 0x7e);
+	sp_tx_aux_rd(ctx, 0x01);
+	c = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, AP_AUX_BUFF_START);
+	if (c < 0) {
+		DRM_ERROR("IO error : access AUX BUFF.\n");
+		return -EIO;
+	}
+
+	DRM_DEV_DEBUG_DRIVER(dev, " EDID Block = %d\n", c + 1);
+
+	if (c > MAX_EDID_BLOCK)
+		c = 1;
+
+	return c;
+}
+
+static int edid_read(struct anx7625_data *ctx,
+		     u8 offset, u8 *pblock_buf)
+{
+	int ret, cnt;
+	struct device *dev = &ctx->client->dev;
+
+	for (cnt = 0; cnt <= EDID_TRY_CNT; cnt++) {
+		sp_tx_aux_wr(ctx, offset);
+		/* set I2C read com 0x01 mot = 0 and read 16 bytes */
+		ret = sp_tx_aux_rd(ctx, 0xf1);
+
+		if (ret) {
+			sp_tx_rst_aux(ctx);
+			DRM_DEV_DEBUG_DRIVER(dev, "edid read failed, reset!\n");
+		} else {
+			ret = anx7625_reg_block_read(ctx, ctx->i2c.rx_p0_client,
+						     AP_AUX_BUFF_START,
+						     MAX_DPCD_BUFFER_SIZE,
+						     pblock_buf);
+			if (!ret)
+				break;
+		}
+	}
+
+	if (cnt > EDID_TRY_CNT)
+		return -EIO;
+
+	return 0;
+}
+
+static int segments_edid_read(struct anx7625_data *ctx,
+			      u8 segment, u8 *buf, u8 offset)
+{
+	u8 cnt;
+	int ret;
+	struct device *dev = &ctx->client->dev;
+
+	/* write address only */
+	ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				AP_AUX_ADDR_7_0, 0x30);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				 AP_AUX_COMMAND, 0x04);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				 AP_AUX_CTRL_STATUS,
+				 AP_AUX_CTRL_ADDRONLY | AP_AUX_CTRL_OP_EN);
+
+	ret |= wait_aux_op_finish(ctx);
+	/* write segment address */
+	ret |= sp_tx_aux_wr(ctx, segment);
+	/* data read */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				 AP_AUX_ADDR_7_0, 0x50);
+	if (ret) {
+		DRM_ERROR("IO error : aux initial failed.\n");
+		return ret;
+	}
+
+	for (cnt = 0; cnt <= EDID_TRY_CNT; cnt++) {
+		sp_tx_aux_wr(ctx, offset);
+		/* set I2C read com 0x01 mot = 0 and read 16 bytes */
+		ret = sp_tx_aux_rd(ctx, 0xf1);
+
+		if (ret) {
+			ret = sp_tx_rst_aux(ctx);
+			DRM_DEV_ERROR(dev, "segment read failed, reset!\n");
+		} else {
+			ret = anx7625_reg_block_read(ctx, ctx->i2c.rx_p0_client,
+						     AP_AUX_BUFF_START,
+						     MAX_DPCD_BUFFER_SIZE, buf);
+			if (!ret)
+				break;
+		}
+	}
+
+	if (cnt > EDID_TRY_CNT)
+		return -EIO;
+
+	return 0;
+}
+
+static int sp_tx_edid_read(struct anx7625_data *ctx,
+			   u8 *pedid_blocks_buf)
+{
+	u8 offset, edid_pos;
+	int count, blocks_num;
+	u8 pblock_buf[MAX_DPCD_BUFFER_SIZE];
+	u8 i, j;
+	u8 g_edid_break = 0;
+	int ret;
+	struct device *dev = &ctx->client->dev;
+
+	/* address initial */
+	ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				AP_AUX_ADDR_7_0, 0x50);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				 AP_AUX_ADDR_15_8, 0);
+	ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
+				 AP_AUX_ADDR_19_16, 0xf0);
+	if (ret < 0) {
+		DRM_ERROR("access aux channel IO error.\n");
+		return -EIO;
+	}
+
+	blocks_num = sp_tx_get_edid_block(ctx);
+	if (blocks_num < 0)
+		return blocks_num;
+
+	count = 0;
+
+	do {
+		switch (count) {
+		case 0:
+		case 1:
+			for (i = 0; i < 8; i++) {
+				offset = (i + count * 8) * MAX_DPCD_BUFFER_SIZE;
+				g_edid_break = edid_read(ctx, offset,
+							 pblock_buf);
+
+				if (g_edid_break)
+					break;
+
+				memcpy(&pedid_blocks_buf[offset],
+				       pblock_buf,
+				       MAX_DPCD_BUFFER_SIZE);
+			}
+
+			break;
+		case 2:
+			offset = 0x00;
+
+			for (j = 0; j < 8; j++) {
+				edid_pos = (j + count * 8) *
+					MAX_DPCD_BUFFER_SIZE;
+
+				if (g_edid_break == 1)
+					break;
+
+				segments_edid_read(ctx, count / 2,
+						   pblock_buf, offset);
+				memcpy(&pedid_blocks_buf[edid_pos],
+				       pblock_buf,
+				       MAX_DPCD_BUFFER_SIZE);
+				offset = offset + 0x10;
+			}
+
+			break;
+		case 3:
+			offset = 0x80;
+
+			for (j = 0; j < 8; j++) {
+				edid_pos = (j + count * 8) *
+					MAX_DPCD_BUFFER_SIZE;
+				if (g_edid_break == 1)
+					break;
+
+				segments_edid_read(ctx, count / 2,
+						   pblock_buf, offset);
+				memcpy(&pedid_blocks_buf[edid_pos],
+				       pblock_buf,
+				       MAX_DPCD_BUFFER_SIZE);
+				offset = offset + 0x10;
+			}
+
+			break;
+		default:
+			break;
+		}
+
+		count++;
+
+	} while (blocks_num >= count);
+
+	/* check edid data */
+	if (!drm_edid_is_valid((struct edid *)pedid_blocks_buf)) {
+		DRM_DEV_ERROR(dev, "WARNING! edid check failed!\n");
+		return -EINVAL;
+	}
+
+	/* reset aux channel */
+	sp_tx_rst_aux(ctx);
+
+	return (blocks_num + 1);
+}
+
+static void anx7625_power_on(struct anx7625_data *ctx)
+{
+	struct device *dev = &ctx->client->dev;
+
+	if (!ctx->pdata.low_power_mode) {
+		DRM_DEV_DEBUG_DRIVER(dev, "Anx7625 not low power mode!\n");
+		return;
+	}
+
+	/* power on pin enable */
+	gpiod_set_value(ctx->pdata.gpio_p_on, 1);
+	usleep_range(10000, 11000);
+	/* power reset pin enable */
+	gpiod_set_value(ctx->pdata.gpio_reset, 1);
+	usleep_range(10000, 11000);
+
+	DRM_DEV_DEBUG_DRIVER(dev, "Anx7625 power on !\n");
+}
+
+static void anx7625_power_standby(struct anx7625_data *ctx)
+{
+	struct device *dev = &ctx->client->dev;
+
+	if (!ctx->pdata.low_power_mode) {
+		DRM_DEV_DEBUG_DRIVER(dev, "anx7625 not low power mode!\n");
+		return;
+	}
+
+	gpiod_set_value(ctx->pdata.gpio_reset, 0);
+	usleep_range(1000, 1100);
+	gpiod_set_value(ctx->pdata.gpio_p_on, 0);
+	usleep_range(1000, 1100);
+	DRM_DEV_DEBUG_DRIVER(dev, "anx7625 power down\n");
+}
+
+/* basic configurations of ANX7625 */
+static void anx7625_config(struct anx7625_data *ctx)
+{
+	anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+			  XTAL_FRQ_SEL, XTAL_FRQ_27M);
+}
+
+static void anx7625_disable_pd_protocol(struct anx7625_data *ctx)
+{
+	struct device *dev = &ctx->client->dev;
+	int ret;
+
+	/* reset main ocm */
+	ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 0x88, 0x40);
+	/* Disable PD */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				 AP_AV_STATUS, AP_DISABLE_PD);
+	/* release main ocm */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 0x88, 0x00);
+
+	if (ret < 0)
+		DRM_DEV_DEBUG_DRIVER(dev, "disable PD feature failed.\n");
+	else
+		DRM_DEV_DEBUG_DRIVER(dev, "disable PD feature succeeded.\n");
+}
+
+static void anx7625_power_on_init(struct anx7625_data *ctx)
+{
+	int retry_count, i;
+	int ret;
+	struct device *dev = &ctx->client->dev;
+
+	for (retry_count = 0; retry_count < 3; retry_count++) {
+		anx7625_power_on(ctx);
+		anx7625_config(ctx);
+
+		for (i = 0; i < OCM_LOADING_TIME; i++) {
+			/* check interface workable */
+			ret = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client,
+					       FLASH_LOAD_STA);
+			if (ret < 0) {
+				DRM_ERROR("IO error : access flash load.\n");
+				return;
+			}
+			if ((ret & FLASH_LOAD_STA_CHK) == FLASH_LOAD_STA_CHK) {
+				anx7625_disable_pd_protocol(ctx);
+				DRM_DEV_DEBUG_DRIVER(dev,
+						     "Firmware ver %02x%02x,",
+					anx7625_reg_read(ctx,
+							 ctx->i2c.rx_p0_client,
+							 OCM_FW_VERSION),
+					anx7625_reg_read(ctx,
+							 ctx->i2c.rx_p0_client,
+							 OCM_FW_REVERSION));
+				DRM_DEV_DEBUG_DRIVER(dev, "Driver version %s\n",
+						     ANX7625_DRV_VERSION);
+
+				return;
+			}
+			usleep_range(1000, 1100);
+		}
+		anx7625_power_standby(ctx);
+	}
+}
+
+static int anx7625_extcon_notifier(struct notifier_block *nb,
+				   unsigned long event, void *ptr)
+{
+	struct anx7625_data *ctx =
+		container_of(nb, struct anx7625_data, event_nb);
+
+	schedule_work(&ctx->extcon_wq);
+	return NOTIFY_DONE;
+}
+
+static void anx7625_chip_control(struct anx7625_data *ctx, int state)
+{
+	struct device *dev = &ctx->client->dev;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "before set, power_state(%d).\n",
+			     atomic_read(&ctx->power_status));
+
+	if (!ctx->pdata.low_power_mode)
+		return;
+
+	if (state) {
+		atomic_inc(&ctx->power_status);
+		if (atomic_read(&ctx->power_status) == 1)
+			anx7625_power_on_init(ctx);
+	} else {
+		if (atomic_read(&ctx->power_status)) {
+			atomic_dec(&ctx->power_status);
+
+			if (atomic_read(&ctx->power_status) == 0)
+				anx7625_power_standby(ctx);
+		}
+	}
+
+	DRM_DEV_DEBUG_DRIVER(dev, "after set, power_state(%d).\n",
+			     atomic_read(&ctx->power_status));
+}
+
+static void anx7625_extcon_work(struct work_struct *work)
+{
+	struct anx7625_data *ctx =
+		container_of(work, struct anx7625_data, extcon_wq);
+	int state = extcon_get_state(ctx->extcon, EXTCON_DISP_DP);
+
+	mutex_lock(&ctx->lock);
+	anx7625_chip_control(ctx, state);
+	mutex_unlock(&ctx->lock);
+}
+
+static int anx7625_extcon_notifier_init(struct anx7625_data *ctx)
+{
+	int ret;
+	struct device *dev = &ctx->client->dev;
+
+	ctx->event_nb.notifier_call = anx7625_extcon_notifier;
+	INIT_WORK(&ctx->extcon_wq, anx7625_extcon_work);
+	ret = devm_extcon_register_notifier(&ctx->client->dev, ctx->extcon,
+					    EXTCON_DISP_DP, &ctx->event_nb);
+	if (ret) {
+		DRM_DEV_ERROR(dev, "failed to register notifier for DP");
+		return ret;
+	}
+	return 0;
+}
+
+static void anx7625_init_gpio(struct anx7625_data *platform)
+{
+	struct device *dev = &platform->client->dev;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "anx7625 init gpio\n");
+
+	/* gpio for chip power enable */
+	platform->pdata.gpio_p_on =
+		devm_gpiod_get_optional(dev, "enable", GPIOD_OUT_LOW);
+	/* gpio for chip reset */
+	platform->pdata.gpio_reset =
+		devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
+
+	if (platform->pdata.gpio_p_on && platform->pdata.gpio_reset) {
+		platform->pdata.low_power_mode = 1;
+		DRM_DEV_DEBUG_DRIVER(dev, "low power mode, pon %d, reset %d.\n",
+				     desc_to_gpio(platform->pdata.gpio_p_on),
+				     desc_to_gpio(platform->pdata.gpio_reset));
+	} else {
+		platform->pdata.low_power_mode = 0;
+		DRM_DEV_DEBUG_DRIVER(dev, "not low power mode.\n");
+	}
+}
+
+static void anx7625_stop_dp_work(struct anx7625_data *ctx)
+{
+	ctx->hpd_status = 0;
+	ctx->hpd_high_cnt = 0;
+	ctx->display_timing_valid = 0;
+
+	ctx->slimport_edid_p.edid_block_num = -1;
+
+	if (ctx->pdata.low_power_mode == 0)
+		anx7625_disable_pd_protocol(ctx);
+}
+
+static void anx7625_start_dp_work(struct anx7625_data *ctx)
+{
+	int ret;
+	struct device *dev = &ctx->client->dev;
+
+	if (ctx->hpd_high_cnt >= 2) {
+		DRM_DEV_DEBUG_DRIVER(dev, "anx7625 filter useless HPD\n");
+		return;
+	}
+
+	ctx->hpd_high_cnt++;
+
+	/* not support HDCP */
+	ret = anx7625_write_and(ctx, ctx->i2c.rx_p1_client, 0xee, 0x9f);
+
+	/* try auth flag */
+	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xec, 0x10);
+	/* interrupt for DRM */
+	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xff, 0x01);
+	if (ret < 0)
+		return;
+
+	ret = anx7625_reg_read(ctx, ctx->i2c.rx_p1_client, 0x86);
+	if (ret < 0)
+		return;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "Secure OCM version=%02x\n", ret);
+}
+
+static int anx7625_read_hpd_status_p0(struct anx7625_data *ctx)
+{
+	return anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, SYSTEM_STSTUS);
+}
+
+static void anx7625_hpd_polling(struct anx7625_data *ctx)
+{
+	int ret, val;
+	struct device *dev = &ctx->client->dev;
+
+	if (atomic_read(&ctx->power_status) != 1) {
+		DRM_DEV_DEBUG_DRIVER(dev, "No need to poling HPD status.\n");
+		return;
+	}
+
+	ret = readx_poll_timeout(anx7625_read_hpd_status_p0,
+				 ctx, val,
+				 ((val & HPD_STATUS) || (val < 0)),
+				 5000,
+				 5000 * 100);
+	if (ret) {
+		DRM_DEV_ERROR(dev, "HPD polling timeout!\n");
+	} else {
+		DRM_DEV_DEBUG_DRIVER(dev, "HPD raise up.\n");
+		anx7625_reg_write(ctx, ctx->i2c.tcpc_client,
+				  INTR_ALERT_1, 0xFF);
+		anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				  INTERFACE_CHANGE_INT, 0);
+	}
+
+	anx7625_start_dp_work(ctx);
+}
+
+static void anx7625_disconnect_check(struct anx7625_data *ctx)
+{
+	if (atomic_read(&ctx->power_status) == 0)
+		anx7625_stop_dp_work(ctx);
+}
+
+static void anx7625_low_power_mode_check(struct anx7625_data *ctx,
+					 int state)
+{
+	struct device *dev = &ctx->client->dev;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "low power mode check, state(%d).\n", state);
+
+	if (ctx->pdata.low_power_mode) {
+		anx7625_chip_control(ctx, state);
+		if (state)
+			anx7625_hpd_polling(ctx);
+		else
+			anx7625_disconnect_check(ctx);
+	}
+}
+
+static void dp_hpd_change_handler(struct anx7625_data *ctx, bool on)
+{
+	struct device *dev = &ctx->client->dev;
+
+	/* hpd changed */
+	DRM_DEV_DEBUG_DRIVER(dev, "dp_hpd_change_default_func: %d\n",
+			     (u32)on);
+
+	if (on == 0) {
+		DRM_DEV_DEBUG_DRIVER(dev, " HPD low\n");
+		anx7625_stop_dp_work(ctx);
+	} else {
+		DRM_DEV_DEBUG_DRIVER(dev, " HPD high\n");
+		anx7625_start_dp_work(ctx);
+	}
+
+	ctx->hpd_status = 1;
+}
+
+static int anx7625_hpd_change_detect(struct anx7625_data *ctx)
+{
+	int intr_vector, status;
+	struct device *dev = &ctx->client->dev;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "power_status=%d\n",
+			     (u32)atomic_read(&ctx->power_status));
+
+	status = anx7625_reg_write(ctx, ctx->i2c.tcpc_client,
+				   INTR_ALERT_1, 0xFF);
+	if (status < 0) {
+		DRM_ERROR("IO error : clear alert register.\n");
+		return status;
+	}
+
+	intr_vector = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client,
+				       INTERFACE_CHANGE_INT);
+	if (intr_vector < 0) {
+		DRM_ERROR("IO error : access interrupt change register.\n");
+		return intr_vector;
+	}
+	DRM_DEV_DEBUG_DRIVER(dev, "0x7e:0x44=%x\n", intr_vector);
+	status = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				   INTERFACE_CHANGE_INT,
+				   intr_vector & (~intr_vector));
+	if (status < 0) {
+		DRM_ERROR("IO error : clear interrupt change register.\n");
+		return status;
+	}
+
+	if (!(intr_vector & HPD_STATUS_CHANGE))
+		return -ENOENT;
+
+	status = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client,
+				  SYSTEM_STSTUS);
+	if (status < 0) {
+		DRM_ERROR("IO error : clear interrupt status.\n");
+		return status;
+	}
+
+	DRM_DEV_DEBUG_DRIVER(dev, "0x7e:0x45=%x\n", status);
+	dp_hpd_change_handler(ctx, status & HPD_STATUS);
+
+	return 0;
+}
+
+static void anx7625_work_func(struct work_struct *work)
+{
+	int event;
+	struct anx7625_data *ctx = container_of(work,
+						struct anx7625_data, work);
+
+	mutex_lock(&ctx->lock);
+	event = anx7625_hpd_change_detect(ctx);
+	mutex_unlock(&ctx->lock);
+
+	if (event < 0)
+		return;
+
+	if (ctx->bridge_attached)
+		drm_helper_hpd_irq_event(ctx->connector.dev);
+}
+
+static irqreturn_t anx7625_intr_hpd_isr(int irq, void *data)
+{
+	struct anx7625_data *ctx = (struct anx7625_data *)data;
+
+	if (atomic_read(&ctx->power_status) != 1)
+		return IRQ_NONE;
+
+	queue_work(ctx->workqueue, &ctx->work);
+
+	return IRQ_HANDLED;
+}
+
+#ifdef CONFIG_OF
+static int anx7625_parse_dt(struct device *dev,
+			    struct anx7625_platform_data *pdata)
+{
+	struct device_node *np = dev->of_node;
+	struct device_node *panel_node, *out_ep;
+
+	of_property_read_u32(dev->of_node, "panel_flags",
+			     &pdata->panel_flags);
+	DRM_DEV_DEBUG_DRIVER(dev, "panel_flags : %d\n", pdata->panel_flags);
+
+	if (pdata->panel_flags == 1)
+		pdata->internal_panel = 1;
+	else if (pdata->panel_flags == 2)
+		pdata->extcon_supported = 1;
+	DRM_DEV_DEBUG_DRIVER(dev, "%s support extcon, %s internal panel\n",
+			     pdata->extcon_supported ? "" : "not",
+			     pdata->internal_panel ? "has" : "no");
+
+	pdata->node.mipi_dsi_host_node = of_graph_get_remote_node(np, 0, 0);
+	if (pdata->node.mipi_dsi_host_node) {
+		of_node_put(pdata->node.mipi_dsi_host_node);
+		pdata->dsi_supported = 1;
+		DRM_DEV_DEBUG_DRIVER(dev, "found dsi host node.\n");
+	} else {
+		pdata->node.mipi_dpi_host_node =
+			of_graph_get_remote_node(np, 1, 0);
+
+		if (pdata->node.mipi_dpi_host_node) {
+			of_node_put(pdata->node.mipi_dpi_host_node);
+			DRM_DEV_DEBUG_DRIVER(dev, "found dpi host node.\n");
+		}
+	}
+
+	DRM_DEV_DEBUG_DRIVER(dev, "dsi_supported : %d\n", pdata->dsi_supported);
+
+	pdata->node.panel_node = of_graph_get_port_by_id(np, 2);
+	if (pdata->node.panel_node) {
+		of_node_put(pdata->node.panel_node);
+		out_ep = of_get_child_by_name(pdata->node.panel_node,
+					      "endpoint");
+		if (!out_ep) {
+			DRM_DEV_DEBUG_DRIVER(dev, "cannot get endpoint.\n");
+			return -EPROBE_DEFER;
+		}
+
+		panel_node = of_graph_get_remote_port_parent(out_ep);
+		of_node_put(out_ep);
+
+		pdata->panel = of_drm_find_panel(panel_node);
+		DRM_DEV_DEBUG_DRIVER(dev, "get panel node.\n");
+		of_node_put(panel_node);
+		if (IS_ERR_OR_NULL(pdata->panel))
+			return -EPROBE_DEFER;
+	} else {
+		if (pdata->internal_panel) {
+			DRM_ERROR("failed to get internal panel.\n");
+			return -EPROBE_DEFER;
+		}
+	}
+
+	return 0;
+}
+#else
+static int anx7625_parse_dt(struct device *dev,
+			    struct anx7625_platform_data *pdata)
+{
+	return -ENODEV;
+}
+#endif
+
+static inline struct anx7625_data *connector_to_anx7625(struct drm_connector *c)
+{
+	return container_of(c, struct anx7625_data, connector);
+}
+
+static inline struct anx7625_data *bridge_to_anx7625(struct drm_bridge *bridge)
+{
+	return container_of(bridge, struct anx7625_data, bridge);
+}
+
+static void anx7625_post_disable(struct drm_bridge *bridge)
+{
+	struct anx7625_data *ctx = bridge_to_anx7625(bridge);
+	struct device *dev = &ctx->client->dev;
+	int ret;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "post disable\n");
+
+	if (!ctx->pdata.panel)
+		return;
+
+	ret = drm_panel_unprepare(ctx->pdata.panel);
+	if (ret)
+		DRM_ERROR("failed to unprepare panel: %d\n", ret);
+	else
+		DRM_DEV_DEBUG_DRIVER(dev, "backlight unprepared.\n");
+
+	atomic_set(&ctx->panel_power, 0);
+}
+
+static void anx7625_pre_enable(struct drm_bridge *bridge)
+{
+	struct anx7625_data *ctx = bridge_to_anx7625(bridge);
+	struct device *dev = &ctx->client->dev;
+	int ret;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "pre enable\n");
+
+	if (!ctx->pdata.panel)
+		return;
+
+	ret = drm_panel_prepare(ctx->pdata.panel);
+	if (ret < 0)
+		DRM_ERROR("failed to prepare panel: %d\n", ret);
+	else
+		DRM_DEV_DEBUG_DRIVER(dev, "backlight prepared.\n");
+	atomic_set(&ctx->panel_power, 1);
+}
+
+static int anx7625_get_modes(struct drm_connector *connector)
+{
+	struct anx7625_data *ctx = connector_to_anx7625(connector);
+	int err, num_modes = 0;
+	int turn_off_flag = 0;
+	struct s_edid_data *p_edid = &ctx->slimport_edid_p;
+	struct device *dev = &ctx->client->dev;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "drm get modes\n");
+
+	if (ctx->slimport_edid_p.edid_block_num > 0)
+		goto out;
+
+	mutex_lock(&ctx->lock);
+
+	if (ctx->pdata.panel && atomic_read(&ctx->panel_power) == 0) {
+		turn_off_flag = 1;
+		anx7625_pre_enable(&ctx->bridge);
+	}
+
+	anx7625_low_power_mode_check(ctx, 1);
+
+	p_edid->edid_block_num = sp_tx_edid_read(ctx, p_edid->edid_raw_data);
+
+	err = -EIO;
+	if (p_edid->edid_block_num < 0) {
+		DRM_ERROR("Failed to read EDID.\n");
+		goto fail;
+	}
+
+	err = drm_connector_update_edid_property(connector,
+						 (struct edid *)
+						 &p_edid->edid_raw_data);
+
+	if (err)
+		DRM_ERROR("Failed to update EDID property: %d\n", err);
+
+fail:
+	mutex_unlock(&ctx->lock);
+	anx7625_low_power_mode_check(ctx, 0);
+	if (ctx->pdata.panel && turn_off_flag == 1)
+		anx7625_post_disable(&ctx->bridge);
+
+	if (err)
+		return err;
+
+out:
+	num_modes = drm_add_edid_modes(connector,
+				       (struct edid *)&p_edid->edid_raw_data);
+	DRM_DEV_DEBUG_DRIVER(dev, "num_modes(%d)\n", num_modes);
+
+	return num_modes;
+}
+
+static enum drm_mode_status
+anx7625_connector_mode_valid(struct drm_connector *connector,
+			     struct drm_display_mode *mode)
+{
+	struct anx7625_data *ctx = connector_to_anx7625(connector);
+	struct device *dev = &ctx->client->dev;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "drm modes valid verify\n");
+
+	if (mode->clock > SUPPORT_PIXEL_CLOCK)
+		return MODE_CLOCK_HIGH;
+
+	return MODE_OK;
+}
+
+static struct drm_connector_helper_funcs anx7625_connector_helper_funcs = {
+	.get_modes = anx7625_get_modes,
+	.mode_valid = anx7625_connector_mode_valid,
+};
+
+static enum drm_connector_status anx7625_detect(struct drm_connector *connector,
+						bool force)
+{
+	struct anx7625_data *ctx = connector_to_anx7625(connector);
+	struct device *dev = &ctx->client->dev;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "drm detect\n");
+
+	if (ctx->pdata.internal_panel)
+		return connector_status_connected;
+
+	if (!ctx->hpd_status)
+		return connector_status_disconnected;
+
+	return connector_status_connected;
+}
+
+static const struct drm_connector_funcs anx7625_connector_funcs = {
+	.fill_modes = drm_helper_probe_single_connector_modes,
+	.detect = anx7625_detect,
+	.destroy = drm_connector_cleanup,
+	.reset = drm_atomic_helper_connector_reset,
+	.atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
+	.atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
+};
+
+static int anx7625_attach_dsi(struct anx7625_data *ctx)
+{
+	struct mipi_dsi_host *host;
+	struct mipi_dsi_device *dsi;
+	struct device_node *mipi_host_node;
+	struct device *dev = &ctx->client->dev;
+	const struct mipi_dsi_device_info info = {
+		.type = "anx7625",
+		.channel = 0,
+		.node = NULL,
+	};
+
+	DRM_DEV_DEBUG_DRIVER(dev, "attach dsi\n");
+
+	if (ctx->pdata.dsi_supported)
+		mipi_host_node = ctx->pdata.node.mipi_dsi_host_node;
+	else
+		mipi_host_node = ctx->pdata.node.mipi_dpi_host_node;
+
+	if (!mipi_host_node) {
+		DRM_ERROR("dsi host is not configured.\n");
+		return -EINVAL;
+	}
+
+	host = of_find_mipi_dsi_host_by_node(mipi_host_node);
+	if (!host) {
+		DRM_ERROR("failed to find dsi host.\n");
+		return -EINVAL;
+	}
+
+	dsi = mipi_dsi_device_register_full(host, &info);
+	if (IS_ERR(dsi)) {
+		DRM_ERROR("failed to create dsi device.\n");
+		return -EINVAL;
+	}
+
+	dsi->lanes = 4;
+	dsi->format = MIPI_DSI_FMT_RGB888;
+	dsi->mode_flags = MIPI_DSI_MODE_VIDEO	|
+		MIPI_DSI_MODE_VIDEO_SYNC_PULSE	|
+		MIPI_DSI_MODE_EOT_PACKET	|
+		MIPI_DSI_MODE_VIDEO_HSE;
+
+	if (mipi_dsi_attach(dsi) < 0) {
+		DRM_ERROR("failed to attach dsi to host.\n");
+		mipi_dsi_device_unregister(dsi);
+		return -EINVAL;
+	}
+
+	ctx->dsi = dsi;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "attach dsi succeeded.\n");
+
+	return 0;
+}
+
+static void anx7625_bridge_detach(struct drm_bridge *bridge)
+{
+	struct anx7625_data *ctx = bridge_to_anx7625(bridge);
+
+	if (ctx->dsi) {
+		mipi_dsi_detach(ctx->dsi);
+		mipi_dsi_device_unregister(ctx->dsi);
+	}
+
+	if (ctx->bridge_attached)
+		drm_connector_unregister(&ctx->connector);
+}
+
+static int anx7625_bridge_attach(struct drm_bridge *bridge)
+{
+	struct anx7625_data *ctx = bridge_to_anx7625(bridge);
+	int err;
+	struct device *dev = &ctx->client->dev;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "drm attach\n");
+	if (!bridge->encoder) {
+		DRM_ERROR("Parent encoder object not found");
+		return -ENODEV;
+	}
+
+	err = drm_connector_init(bridge->dev, &ctx->connector,
+				 &anx7625_connector_funcs,
+				 DRM_MODE_CONNECTOR_DisplayPort);
+	if (err) {
+		DRM_ERROR("Failed to initialize connector: %d\n", err);
+		return err;
+	}
+
+	drm_connector_helper_add(&ctx->connector,
+				 &anx7625_connector_helper_funcs);
+
+	err = drm_connector_register(&ctx->connector);
+	if (err) {
+		DRM_ERROR("Failed to register connector: %d\n", err);
+		return err;
+	}
+
+	ctx->connector.polled = DRM_CONNECTOR_POLL_HPD;
+
+	err = drm_connector_attach_encoder(&ctx->connector, bridge->encoder);
+	if (err) {
+		DRM_ERROR("Failed to link up connector to encoder: %d\n", err);
+		drm_connector_unregister(&ctx->connector);
+		return err;
+	}
+
+	err = anx7625_attach_dsi(ctx);
+	if (err) {
+		DRM_ERROR("Failed to attach to dsi : %d\n", err);
+		drm_connector_unregister(&ctx->connector);
+		return err;
+	}
+
+	ctx->bridge_attached = 1;
+
+	return 0;
+}
+
+static enum drm_mode_status
+anx7625_bridge_mode_valid(struct drm_bridge *bridge,
+			  const struct drm_display_mode *mode)
+{
+	struct anx7625_data *ctx = bridge_to_anx7625(bridge);
+	struct device *dev = &ctx->client->dev;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "drm mode checking\n");
+
+	/* Max 1200p at 5.4 Ghz, one lane, pixel clock 300M */
+	if (mode->clock > SUPPORT_PIXEL_CLOCK) {
+		DRM_DEV_DEBUG_DRIVER(dev,
+				     "drm mode invalid, pixelclock too high.\n");
+		return MODE_CLOCK_HIGH;
+	}
+
+	DRM_DEV_DEBUG_DRIVER(dev, "drm mode valid.\n");
+
+	return MODE_OK;
+}
+
+static void anx7625_bridge_mode_set(struct drm_bridge *bridge,
+				    const struct drm_display_mode *old_mode,
+				    const struct drm_display_mode *mode)
+{
+	struct anx7625_data *ctx = bridge_to_anx7625(bridge);
+	struct device *dev = &ctx->client->dev;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "drm mode set\n");
+
+	mutex_lock(&ctx->lock);
+
+	ctx->dt.pixelclock.min = mode->clock;
+	ctx->dt.hactive.min = mode->hdisplay;
+	ctx->dt.hsync_len.min = mode->hsync_end - mode->hsync_start;
+	ctx->dt.hfront_porch.min = mode->hsync_start - mode->hdisplay;
+	ctx->dt.hback_porch.min = mode->htotal - mode->hsync_end;
+	ctx->dt.vactive.min = mode->vdisplay;
+	ctx->dt.vsync_len.min = mode->vsync_end - mode->vsync_start;
+	ctx->dt.vfront_porch.min = mode->vsync_start - mode->vdisplay;
+	ctx->dt.vback_porch.min = mode->vtotal - mode->vsync_end;
+
+	ctx->display_timing_valid = 1;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "pixelclock(%d).\n", ctx->dt.pixelclock.min);
+	DRM_DEV_DEBUG_DRIVER(dev, "hactive(%d), hsync(%d), hfp(%d), hbp(%d)\n",
+			     ctx->dt.hactive.min,
+			     ctx->dt.hsync_len.min,
+			     ctx->dt.hfront_porch.min,
+			     ctx->dt.hback_porch.min);
+	DRM_DEV_DEBUG_DRIVER(dev, "vactive(%d), vsync(%d), vfp(%d), vbp(%d)\n",
+			     ctx->dt.vactive.min,
+			     ctx->dt.vsync_len.min,
+			     ctx->dt.vfront_porch.min,
+			     ctx->dt.vback_porch.min);
+	DRM_DEV_DEBUG_DRIVER(dev, "hdisplay(%d),hsync_start(%d).\n",
+			     mode->hdisplay,
+			     mode->hsync_start);
+	DRM_DEV_DEBUG_DRIVER(dev, "hsync_end(%d),htotal(%d).\n",
+			     mode->hsync_end,
+			     mode->htotal);
+	DRM_DEV_DEBUG_DRIVER(dev, "vdisplay(%d),vsync_start(%d).\n",
+			     mode->vdisplay,
+			     mode->vsync_start);
+	DRM_DEV_DEBUG_DRIVER(dev, "vsync_end(%d),vtotal(%d).\n",
+			     mode->vsync_end,
+			     mode->vtotal);
+
+	mutex_unlock(&ctx->lock);
+}
+
+static void anx7625_bridge_enable(struct drm_bridge *bridge)
+{
+	struct anx7625_data *ctx = bridge_to_anx7625(bridge);
+	struct device *dev = &ctx->client->dev;
+	int ret;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "drm enable\n");
+
+	anx7625_low_power_mode_check(ctx, 1);
+
+	if (WARN_ON(!atomic_read(&ctx->power_status)))
+		return;
+
+	if (ctx->pdata.panel) {
+		ret = drm_panel_enable(ctx->pdata.panel);
+		if (ret < 0) {
+			DRM_ERROR("failed to enable panel: %d.\n", ret);
+			return;
+		}
+	}
+
+	mutex_lock(&ctx->lock);
+	anx7625_dp_start(ctx);
+	mutex_unlock(&ctx->lock);
+}
+
+static void anx7625_bridge_disable(struct drm_bridge *bridge)
+{
+	struct anx7625_data *ctx = bridge_to_anx7625(bridge);
+	struct device *dev = &ctx->client->dev;
+	int ret;
+
+	if (WARN_ON(!atomic_read(&ctx->power_status)))
+		return;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "drm disable\n");
+
+	if (ctx->pdata.panel) {
+		ret = drm_panel_disable(ctx->pdata.panel);
+		if (ret < 0)
+			DRM_ERROR("failed to disable panel: %d.\n", ret);
+	}
+
+	DRM_DEV_DEBUG_DRIVER(dev, "drm disable\n");
+	mutex_lock(&ctx->lock);
+
+	anx7625_dp_stop(ctx);
+
+	anx7625_low_power_mode_check(ctx, 0);
+
+	mutex_unlock(&ctx->lock);
+}
+
+static const struct drm_bridge_funcs anx7625_bridge_funcs = {
+	.attach = anx7625_bridge_attach,
+	.detach = anx7625_bridge_detach,
+	.disable = anx7625_bridge_disable,
+	.post_disable = anx7625_post_disable,
+	.pre_enable = anx7625_pre_enable,
+	.mode_valid = anx7625_bridge_mode_valid,
+	.mode_set = anx7625_bridge_mode_set,
+	.enable = anx7625_bridge_enable,
+};
+
+static int anx7625_register_i2c_dummy_clients(struct anx7625_data *ctx,
+					      struct i2c_client *client)
+{
+	ctx->i2c.tx_p0_client = i2c_new_dummy(client->adapter,
+					      TX_P0_ADDR >> 1);
+	if (!ctx->i2c.tx_p0_client)
+		return -ENOMEM;
+
+	ctx->i2c.tx_p1_client = i2c_new_dummy(client->adapter,
+					      TX_P1_ADDR >> 1);
+	if (!ctx->i2c.tx_p1_client)
+		goto free_tx_p0;
+
+	ctx->i2c.tx_p2_client = i2c_new_dummy(client->adapter,
+					      TX_P2_ADDR >> 1);
+	if (!ctx->i2c.tx_p2_client)
+		goto free_tx_p1;
+
+	ctx->i2c.rx_p0_client = i2c_new_dummy(client->adapter,
+					      RX_P0_ADDR >> 1);
+	if (!ctx->i2c.rx_p0_client)
+		goto free_tx_p2;
+
+	ctx->i2c.rx_p1_client = i2c_new_dummy(client->adapter,
+					      RX_P1_ADDR >> 1);
+	if (!ctx->i2c.rx_p1_client)
+		goto free_rx_p0;
+
+	ctx->i2c.rx_p2_client = i2c_new_dummy(client->adapter,
+					      RX_P2_ADDR >> 1);
+	if (!ctx->i2c.rx_p2_client)
+		goto free_rx_p1;
+
+	ctx->i2c.tcpc_client = i2c_new_dummy(client->adapter,
+					     TCPC_INTERFACE_ADDR >> 1);
+	if (!ctx->i2c.tcpc_client)
+		goto free_rx_p2;
+
+	return 0;
+
+free_rx_p2:
+	i2c_unregister_device(ctx->i2c.rx_p2_client);
+free_rx_p1:
+	i2c_unregister_device(ctx->i2c.rx_p1_client);
+free_rx_p0:
+	i2c_unregister_device(ctx->i2c.rx_p0_client);
+free_tx_p2:
+	i2c_unregister_device(ctx->i2c.tx_p2_client);
+free_tx_p1:
+	i2c_unregister_device(ctx->i2c.tx_p1_client);
+free_tx_p0:
+	i2c_unregister_device(ctx->i2c.tx_p0_client);
+
+	return -ENOMEM;
+}
+
+static void anx7625_unregister_i2c_dummy_clients(struct anx7625_data *ctx)
+{
+	i2c_unregister_device(ctx->i2c.tx_p0_client);
+	i2c_unregister_device(ctx->i2c.tx_p1_client);
+	i2c_unregister_device(ctx->i2c.tx_p2_client);
+	i2c_unregister_device(ctx->i2c.rx_p0_client);
+	i2c_unregister_device(ctx->i2c.rx_p1_client);
+	i2c_unregister_device(ctx->i2c.rx_p2_client);
+	i2c_unregister_device(ctx->i2c.tcpc_client);
+}
+
+static int anx7625_i2c_probe(struct i2c_client *client,
+			     const struct i2c_device_id *id)
+{
+	struct anx7625_data *platform;
+	struct anx7625_platform_data *pdata;
+	int ret = 0;
+	struct device *dev = &client->dev;
+
+	if (!i2c_check_functionality(client->adapter,
+				     I2C_FUNC_SMBUS_I2C_BLOCK)) {
+		DRM_DEV_ERROR(dev, "anx7625's i2c bus doesn't support\n");
+		return -ENODEV;
+	}
+
+	platform = kzalloc(sizeof(*platform), GFP_KERNEL);
+	if (!platform) {
+		DRM_DEV_ERROR(dev, "failed to allocate driver data\n");
+		return -ENOMEM;
+	}
+
+	pdata = &platform->pdata;
+
+	ret = anx7625_parse_dt(dev, pdata);
+	if (ret) {
+		DRM_DEV_ERROR(dev, "failed to parse devicetree.\n");
+		goto free_platform;
+	}
+
+	anx7625_init_gpio(platform);
+
+	/* to access global platform data */
+	platform->client = client;
+	i2c_set_clientdata(client, platform);
+
+	if (platform->pdata.extcon_supported) {
+		/* get extcon device from DTS */
+		ret = -EINVAL;
+		platform->extcon = extcon_get_edev_by_phandle(dev, 0);
+		if (PTR_ERR(platform->extcon) == -EPROBE_DEFER)
+			goto free_platform;
+
+		if (IS_ERR(platform->extcon)) {
+			DRM_DEV_ERROR(dev,
+				      "can not get extcon device!");
+			goto free_platform;
+		}
+
+		ret = anx7625_extcon_notifier_init(platform);
+		if (ret)
+			goto free_platform;
+	}
+
+	atomic_set(&platform->power_status, 0);
+
+	mutex_init(&platform->lock);
+
+	platform->pdata.intp_irq = client->irq;
+	if (platform->pdata.intp_irq) {
+		INIT_WORK(&platform->work, anx7625_work_func);
+		platform->workqueue = create_workqueue("anx7625_work");
+		if (!platform->workqueue) {
+			DRM_DEV_ERROR(dev, "failed to create work queue\n");
+			ret = -ENOMEM;
+			goto free_platform;
+		}
+
+		ret = devm_request_threaded_irq(dev, platform->pdata.intp_irq,
+						NULL, anx7625_intr_hpd_isr,
+						IRQF_TRIGGER_FALLING |
+						IRQF_ONESHOT,
+						"anx7625-intp", platform);
+		if (ret) {
+			DRM_DEV_ERROR(dev, "failed to request irq\n");
+			goto free_wq;
+		}
+	}
+
+	if (anx7625_register_i2c_dummy_clients(platform, client) != 0) {
+		ret = -ENOMEM;
+		DRM_ERROR("Failed to reserve I2C bus.\n");
+		goto free_wq;
+	}
+
+	if (platform->pdata.low_power_mode == 0) {
+		anx7625_disable_pd_protocol(platform);
+		atomic_set(&platform->power_status, 1);
+	}
+
+	/* add work function */
+	if (platform->pdata.intp_irq)
+		queue_work(platform->workqueue, &platform->work);
+
+	platform->bridge.funcs = &anx7625_bridge_funcs;
+	if (IS_ENABLED(CONFIG_OF))
+		platform->bridge.of_node = client->dev.of_node;
+	drm_bridge_add(&platform->bridge);
+
+	DRM_DEV_DEBUG_DRIVER(dev, "probe done\n");
+
+	return 0;
+
+free_wq:
+	if (platform->workqueue)
+		destroy_workqueue(platform->workqueue);
+
+free_platform:
+	kfree(platform);
+
+	return ret;
+}
+
+static int anx7625_i2c_remove(struct i2c_client *client)
+{
+	struct anx7625_data *platform = i2c_get_clientdata(client);
+
+	drm_bridge_remove(&platform->bridge);
+
+	if (platform->pdata.intp_irq)
+		destroy_workqueue(platform->workqueue);
+
+	if (platform->pdata.extcon_supported) {
+		devm_extcon_unregister_notifier(&platform->client->dev,
+						platform->extcon,
+						EXTCON_DISP_DP,
+						&platform->event_nb);
+		flush_work(&platform->extcon_wq);
+	}
+
+	anx7625_unregister_i2c_dummy_clients(platform);
+
+	kfree(platform);
+	return 0;
+}
+
+static const struct i2c_device_id anx7625_id[] = {
+	{"anx7625", 0},
+	{}
+};
+
+MODULE_DEVICE_TABLE(i2c, anx7625_id);
+
+#ifdef CONFIG_OF
+static const struct of_device_id anx_match_table[] = {
+	{.compatible = "analogix,anx7625",},
+	{},
+};
+#endif
+
+static struct i2c_driver anx7625_driver = {
+	.driver = {
+		.name = "anx7625",
+#ifdef CONFIG_OF
+		.of_match_table = anx_match_table,
+#endif
+	},
+	.probe = anx7625_i2c_probe,
+	.remove = anx7625_i2c_remove,
+
+	.id_table = anx7625_id,
+};
+
+module_i2c_driver(anx7625_driver);
+
+MODULE_DESCRIPTION("MIPI2DP anx7625 driver");
+MODULE_AUTHOR("Xin Ji <xji at analogixsemi.com>");
+MODULE_LICENSE("GPL v2");
+MODULE_VERSION(ANX7625_DRV_VERSION);
diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.h b/drivers/gpu/drm/bridge/analogix/anx7625.h
new file mode 100644
index 0000000..c871a6c
--- /dev/null
+++ b/drivers/gpu/drm/bridge/analogix/anx7625.h
@@ -0,0 +1,406 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright(c) 2016, Analogix Semiconductor. All rights reserved.
+ *
+ */
+
+#ifndef __ANX7625_H__
+#define __ANX7625_H__
+
+#ifndef LOG_TAG
+#define LOG_TAG "anx7625dp"
+#endif
+
+#define ANX7625_DRV_VERSION "0.1.04"
+
+/* Loading OCM re-trying times */
+#define OCM_LOADING_TIME 10
+
+/*********  ANX7625 Register  **********/
+#define TX_P0_ADDR				0x70
+#define TX_P1_ADDR				0x7A
+#define TX_P2_ADDR				0x72
+
+#define RX_P0_ADDR				0x7e
+#define RX_P1_ADDR				0x84
+#define RX_P2_ADDR				0x54
+
+#define RSVD_00_ADDR				0x00
+#define RSVD_D1_ADDR				0xD1
+#define RSVD_60_ADDR				0x60
+#define RSVD_39_ADDR				0x39
+#define RSVD_7F_ADDR				0x7F
+
+#define TCPC_INTERFACE_ADDR			0x58
+
+/* anx7625 clock frequency in Hz */
+#define XTAL_FRQ        (27 * 1000000)
+
+#define  POST_DIVIDER_MIN	1
+#define  POST_DIVIDER_MAX	16
+#define  PLL_OUT_FREQ_MIN	520000000UL
+#define  PLL_OUT_FREQ_MAX	730000000UL
+#define  PLL_OUT_FREQ_ABS_MIN	300000000UL
+#define  PLL_OUT_FREQ_ABS_MAX	800000000UL
+#define  MAX_UNSIGNED_24BIT	16777215UL
+
+/***************************************************************/
+/* Register definition of device address 0x58 */
+
+#define PRODUCT_ID_L 0x02
+#define PRODUCT_ID_H 0x03
+
+#define INTR_ALERT_1  0xCC
+#define INTR_SOFTWARE_INT BIT(3)
+#define INTR_RECEIVED_MSG BIT(5)
+
+#define SYSTEM_STSTUS 0x45
+#define INTERFACE_CHANGE_INT 0x44
+#define HPD_STATUS_CHANGE 0x80
+#define HPD_STATUS 0x80
+
+/******** END of I2C Address 0x58 ********/
+
+/***************************************************************/
+/* Register definition of device address 0x70 */
+#define  I2C_ADDR_70_DPTX              0x70
+
+#define SP_TX_LINK_BW_SET_REG 0xA0
+#define SP_TX_LANE_COUNT_SET_REG 0xA1
+
+#define M_VID_0 0xC0
+#define M_VID_1 0xC1
+#define M_VID_2 0xC2
+#define N_VID_0 0xC3
+#define N_VID_1 0xC4
+#define N_VID_2 0xC5
+
+/***************************************************************/
+/* Register definition of device address 0x72 */
+#define AUX_RST	0x04
+#define RST_CTRL2 0x07
+
+#define SP_TX_TOTAL_LINE_STA_L 0x24
+#define SP_TX_TOTAL_LINE_STA_H 0x25
+#define SP_TX_ACT_LINE_STA_L 0x26
+#define SP_TX_ACT_LINE_STA_H 0x27
+#define SP_TX_V_F_PORCH_STA 0x28
+#define SP_TX_V_SYNC_STA 0x29
+#define SP_TX_V_B_PORCH_STA 0x2A
+#define SP_TX_TOTAL_PIXEL_STA_L 0x2B
+#define SP_TX_TOTAL_PIXEL_STA_H 0x2C
+#define SP_TX_ACT_PIXEL_STA_L 0x2D
+#define SP_TX_ACT_PIXEL_STA_H 0x2E
+#define SP_TX_H_F_PORCH_STA_L 0x2F
+#define SP_TX_H_F_PORCH_STA_H 0x30
+#define SP_TX_H_SYNC_STA_L 0x31
+#define SP_TX_H_SYNC_STA_H 0x32
+#define SP_TX_H_B_PORCH_STA_L 0x33
+#define SP_TX_H_B_PORCH_STA_H 0x34
+
+#define SP_TX_VID_CTRL 0x84
+#define SP_TX_BPC_MASK 0xE0
+#define SP_TX_BPC_6    0x00
+#define SP_TX_BPC_8    0x20
+#define SP_TX_BPC_10   0x40
+#define SP_TX_BPC_12   0x60
+
+#define VIDEO_BIT_MATRIX_12 0x4c
+
+#define AUDIO_CHANNEL_STATUS_1 0xd0
+#define AUDIO_CHANNEL_STATUS_2 0xd1
+#define AUDIO_CHANNEL_STATUS_3 0xd2
+#define AUDIO_CHANNEL_STATUS_4 0xd3
+#define AUDIO_CHANNEL_STATUS_5 0xd4
+#define AUDIO_CHANNEL_STATUS_6 0xd5
+#define TDM_SLAVE_MODE 0x10
+#define I2S_SLAVE_MODE 0x08
+
+#define AUDIO_CONTROL_REGISTER 0xe6
+#define TDM_TIMING_MODE 0x08
+
+#define  I2C_ADDR_72_DPTX              0x72
+
+#define  VIDEO_CONTROL_0  0x08
+
+#define  ACTIVE_LINES_L         0x14
+#define  ACTIVE_LINES_H         0x15  /* note: bit[7:6] are reserved */
+#define  VERTICAL_FRONT_PORCH   0x16
+#define  VERTICAL_SYNC_WIDTH    0x17
+#define  VERTICAL_BACK_PORCH    0x18
+
+#define  HORIZONTAL_TOTAL_PIXELS_L    0x19
+#define  HORIZONTAL_TOTAL_PIXELS_H    0x1A  /* note: bit[7:6] are reserved */
+#define  HORIZONTAL_ACTIVE_PIXELS_L   0x1B
+#define  HORIZONTAL_ACTIVE_PIXELS_H   0x1C  /* note: bit[7:6] are reserved */
+#define  HORIZONTAL_FRONT_PORCH_L     0x1D
+#define  HORIZONTAL_FRONT_PORCH_H     0x1E  /* note: bit[7:4] are reserved */
+#define  HORIZONTAL_SYNC_WIDTH_L      0x1F
+#define  HORIZONTAL_SYNC_WIDTH_H      0x20  /* note: bit[7:4] are reserved */
+#define  HORIZONTAL_BACK_PORCH_L      0x21
+#define  HORIZONTAL_BACK_PORCH_H      0x22  /* note: bit[7:4] are reserved */
+
+/******** END of I2C Address 0x72 *********/
+/***************************************************************/
+/* Register definition of device address 0x7e */
+
+#define  I2C_ADDR_7E_FLASH_CONTROLLER  0x7E
+
+#define FLASH_LOAD_STA 0x05
+#define FLASH_LOAD_STA_CHK	BIT(7)
+
+#define  XTAL_FRQ_SEL    0x3F
+/* bit field positions */
+#define  XTAL_FRQ_SEL_POS    5
+/* bit field values */
+#define  XTAL_FRQ_19M2   (0 << XTAL_FRQ_SEL_POS)
+#define  XTAL_FRQ_27M    (4 << XTAL_FRQ_SEL_POS)
+
+#define  R_DSC_CTRL_0    0x40
+#define  READ_STATUS_EN  7
+#define  CLK_1MEG_RB     6  /* 1MHz clock reset; 0=reset, 0=reset release */
+#define  DSC_BIST_DONE   1  /* bit[5:1]: 1=DSC MBIST pass */
+#define  DSC_EN          0x01  /* 1=DSC enabled, 0=DSC disabled */
+
+#define OCM_FW_VERSION   0x31
+#define OCM_FW_REVERSION 0x32
+
+#define AP_AUX_ADDR_7_0   0x11
+#define AP_AUX_ADDR_15_8  0x12
+#define AP_AUX_ADDR_19_16 0x13
+
+/* note: bit[0:3] AUX status, bit 4 op_en, bit 5 address only */
+#define AP_AUX_CTRL_STATUS 0x14
+#define AP_AUX_CTRL_OP_EN 0x10
+#define AP_AUX_CTRL_ADDRONLY 0x20
+
+#define AP_AUX_BUFF_START 0x15
+#define PIXEL_CLOCK_L 0x25
+#define PIXEL_CLOCK_H 0x26
+
+#define AP_AUX_COMMAND 0x27  /* com+len */
+/* bit 0&1: 3D video structure */
+/* 0x01: frame packing,  0x02:Line alternative, 0x03:Side-by-side(full) */
+#define AP_AV_STATUS 0x28
+#define AP_VIDEO_CHG  BIT(2)
+#define AP_AUDIO_CHG  BIT(3)
+#define AP_MIPI_MUTE  BIT(4) /* 1:MIPI input mute, 0: ummute */
+#define AP_MIPI_RX_EN BIT(5) /* 1: MIPI RX input in  0: no RX in */
+#define AP_DISABLE_PD BIT(6)
+#define AP_DISABLE_DISPLAY BIT(7)
+/***************************************************************/
+/* Register definition of device address 0x84 */
+#define  MIPI_PHY_CONTROL_3            0x03
+#define  MIPI_HS_PWD_CLK               7
+#define  MIPI_HS_RT_CLK                6
+#define  MIPI_PD_CLK                   5
+#define  MIPI_CLK_RT_MANUAL_PD_EN      4
+#define  MIPI_CLK_HS_MANUAL_PD_EN      3
+#define  MIPI_CLK_DET_DET_BYPASS       2
+#define  MIPI_CLK_MISS_CTRL            1
+#define  MIPI_PD_LPTX_CH_MANUAL_PD_EN  0
+
+#define  MIPI_LANE_CTRL_0		0x05
+#define  MIPI_TIME_HS_PRPR		0x08
+
+/* After MIPI RX protocol layer received this many video frames, */
+/* protocol layer starts to reconstruct video stream from PHY */
+#define  MIPI_VIDEO_STABLE_CNT           0x0A
+
+#define  MIPI_LANE_CTRL_10               0x0F
+#define  MIPI_DIGITAL_ADJ_1   0x1B
+
+#define  MIPI_PLL_M_NUM_23_16   0x1E
+#define  MIPI_PLL_M_NUM_15_8    0x1F
+#define  MIPI_PLL_M_NUM_7_0     0x20
+#define  MIPI_PLL_N_NUM_23_16   0x21
+#define  MIPI_PLL_N_NUM_15_8    0x22
+#define  MIPI_PLL_N_NUM_7_0     0x23
+
+#define  MIPI_DIGITAL_PLL_6     0x2A
+/* bit[7:6]: VCO band control, only effective */
+/* when MIPI_PLL_FORCE_BAND_EN (0x84:0x2B[6]) is 1 */
+#define  MIPI_M_NUM_READY        0x10
+#define  MIPI_N_NUM_READY        0x08
+#define  STABLE_INTEGER_CNT_EN   0x04
+#define  MIPI_PLL_TEST_BIT       0
+/* bit[1:0]: test point output select - */
+/* 00: VCO power, 01: dvdd_pdt, 10: dvdd, 11: vcox */
+
+#define  MIPI_DIGITAL_PLL_7      0x2B
+#define  MIPI_PLL_FORCE_N_EN     7
+#define  MIPI_PLL_FORCE_BAND_EN  6
+
+#define  MIPI_PLL_VCO_TUNE_REG   4
+/* bit[5:4]: VCO metal capacitance - */
+/* 00: +20% fast, 01: +10% fast (default), 10: typical, 11: -10% slow */
+#define  MIPI_PLL_VCO_TUNE_REG_VAL   0x30
+
+#define  MIPI_PLL_PLL_LDO_BIT    2
+/* bit[3:2]: vco_v2i power - */
+/* 00: 1.40V, 01: 1.45V (default), 10: 1.50V, 11: 1.55V */
+#define  MIPI_PLL_RESET_N        0x02
+#define  MIPI_FRQ_FORCE_NDET     0
+
+#define  MIPI_ALERT_CLR_0        0x2D
+#define  HS_link_error_clear     7
+/* This bit itself is S/C, and it clears 0x84:0x31[7] */
+
+#define  MIPI_ALERT_OUT_0        0x31
+#define  check_sum_err_hs_sync   7
+/* This bit is cleared by 0x84:0x2D[7] */
+
+#define  MIPI_DIGITAL_PLL_8    0x33
+#define  MIPI_POST_DIV_VAL     4
+/* n means divided by (n+1), n = 0~15 */
+#define  MIPI_EN_LOCK_FRZ      3
+#define  MIPI_FRQ_COUNTER_RST  2
+#define  MIPI_FRQ_SET_REG_8    1
+/* bit 0 is reserved */
+
+#define  MIPI_DIGITAL_PLL_9    0x34
+
+#define  MIPI_DIGITAL_PLL_16   0x3B
+#define  MIPI_FRQ_FREEZE_NDET          7
+#define  MIPI_FRQ_REG_SET_ENABLE       6
+#define  MIPI_REG_FORCE_SEL_EN         5
+#define  MIPI_REG_SEL_DIV_REG          4
+#define  MIPI_REG_FORCE_PRE_DIV_EN     3
+/* bit 2 is reserved */
+#define  MIPI_FREF_D_IND               1
+#define  REF_CLK_27000KHZ    1
+#define  REF_CLK_19200KHZ    0
+#define  MIPI_REG_PLL_PLL_TEST_ENABLE  0
+
+#define  MIPI_DIGITAL_PLL_18  0x3D
+#define  FRQ_COUNT_RB_SEL       7
+#define  REG_FORCE_POST_DIV_EN  6
+#define  MIPI_DPI_SELECT        5
+#define  SELECT_DSI  1
+#define  SELECT_DPI  0
+#define  REG_BAUD_DIV_RATIO     0
+
+#define  H_BLANK_L            0x3E
+/* for DSC only */
+#define  H_BLANK_H            0x3F
+/* for DSC only; note: bit[7:6] are reserved */
+#define  MIPI_SWAP  0x4A
+#define  MIPI_SWAP_CH0    7
+#define  MIPI_SWAP_CH1    6
+#define  MIPI_SWAP_CH2    5
+#define  MIPI_SWAP_CH3    4
+#define  MIPI_SWAP_CLK    3
+/* bit[2:0] are reserved */
+
+/******** END of I2C Address 0x84 *********/
+
+/* DPCD regs */
+#define DPCD_DPCD_REV                  0x00
+#define DPCD_MAX_LINK_RATE             0x01
+#define DPCD_MAX_LANE_COUNT            0x02
+
+/*********  ANX7625 Register End  **********/
+
+/*****************  Display *****************/
+enum audio_fs {
+	AUDIO_FS_441K  = 0x00,
+	AUDIO_FS_48K   = 0x02,
+	AUDIO_FS_32K   = 0x03,
+	AUDIO_FS_882K  = 0x08,
+	AUDIO_FS_96K   = 0x0a,
+	AUDIO_FS_1764K = 0x0c,
+	AUDIO_FS_192K  = 0x0e
+};
+
+enum audio_wd_len {
+	AUDIO_W_LEN_16_20MAX = 0x02,
+	AUDIO_W_LEN_18_20MAX = 0x04,
+	AUDIO_W_LEN_17_20MAX = 0x0c,
+	AUDIO_W_LEN_19_20MAX = 0x08,
+	AUDIO_W_LEN_20_20MAX = 0x0a,
+	AUDIO_W_LEN_20_24MAX = 0x03,
+	AUDIO_W_LEN_22_24MAX = 0x05,
+	AUDIO_W_LEN_21_24MAX = 0x0d,
+	AUDIO_W_LEN_23_24MAX = 0x09,
+	AUDIO_W_LEN_24_24MAX = 0x0b
+};
+
+#define I2S_CH_2	0x01
+#define TDM_CH_4	0x03
+#define TDM_CH_6	0x05
+#define TDM_CH_8	0x07
+
+#define MAX_DPCD_BUFFER_SIZE	16
+
+#define ONE_BLOCK_SIZE      128
+#define FOUR_BLOCK_SIZE     (128 * 4)
+
+#define MAX_EDID_BLOCK	3
+#define EDID_TRY_CNT	3
+#define SUPPORT_PIXEL_CLOCK	300000
+
+struct s_edid_data {
+	int edid_block_num;
+	u8 edid_raw_data[FOUR_BLOCK_SIZE];
+};
+
+/*****************  Display End *****************/
+
+struct anx7625_device_node {
+	struct device_node *mipi_dsi_host_node;
+	struct device_node *mipi_dpi_host_node;
+	struct device_node *panel_node;
+};
+
+struct anx7625_platform_data {
+	struct gpio_desc *gpio_p_on;
+	struct gpio_desc *gpio_reset;
+	struct drm_panel *panel;
+	int intp_irq;
+	u32 panel_flags;
+	u32 low_power_mode;
+	u32 dsi_supported;
+	u32 internal_panel;
+	u32 extcon_supported;
+	struct anx7625_device_node node;
+};
+
+struct anx7625_i2c_client {
+	struct i2c_client *tx_p0_client;
+	struct i2c_client *tx_p1_client;
+	struct i2c_client *tx_p2_client;
+	struct i2c_client *rx_p0_client;
+	struct i2c_client *rx_p1_client;
+	struct i2c_client *rx_p2_client;
+	struct i2c_client *tcpc_client;
+};
+
+struct anx7625_data {
+	struct anx7625_platform_data pdata;
+	atomic_t power_status;
+	atomic_t panel_power;
+	int hpd_status;
+	int hpd_high_cnt;
+	struct i2c_client *client;
+	struct anx7625_i2c_client i2c;
+	struct i2c_client *last_client;
+	struct s_edid_data slimport_edid_p;
+	struct work_struct work;
+	struct workqueue_struct *workqueue;
+	/* drm bridge mutex lock */
+	struct mutex lock;
+	char edid_block;
+	struct display_timing dt;
+	u8 display_timing_valid;
+	struct drm_bridge bridge;
+	u8 bridge_attached;
+	struct drm_connector connector;
+	struct mipi_dsi_device *dsi;
+	struct drm_dp_link link;
+	struct drm_display_mode vid_info;
+	struct notifier_block event_nb;
+	struct extcon_dev *extcon;
+	struct work_struct extcon_wq;
+};
+
+#endif  /* __ANX7625_H__ */
-- 
2.7.4



More information about the dri-devel mailing list