[PATCH V8 1/6] backlight: qcom-wled: Add new properties for PMI8998.

[Kiran Gunda]

Update the bindings with the new properties used for
PMI8998.

Signed-off-by: Kiran Gunda <kgunda at codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson at linaro.org>
Reviewed-by: Rob Herring <robh at kernel.org>
Acked-by: Daniel Thompson <daniel.thompson at linaro.org>
---
 .../bindings/leds/backlight/qcom-wled.txt          | 74 ++++++++++++++++++----
 1 file changed, 63 insertions(+), 11 deletions(-)

diff --git a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt
index 14f28f2..c06863b 100644
--- a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt
+++ b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt
@@ -20,7 +20,7 @@ platforms. The PMIC is connected to the host processor via SPMI bus.
 - default-brightness
 	Usage:        optional
 	Value type:   <u32>
-	Definition:   brightness value on boot, value from: 0-4095
+	Definition:   brightness value on boot, value from: 0-4095.
 		      Default: 2048
 
 - label
@@ -48,20 +48,24 @@ platforms. The PMIC is connected to the host processor via SPMI bus.
 - qcom,current-limit
 	Usage:        optional
 	Value type:   <u32>
-	Definition:   mA; per-string current limit
-		      value: For pm8941: from 0 to 25 with 5 mA step
-			     Default 20 mA.
-			     For pmi8998: from 0 to 30 with 5 mA step
-			     Default 25 mA.
+	Definition:   mA; per-string current limit; value from 0 to 25 with
+		      1 mA step. Default 20 mA.
+		      This property is supported only for pm8941.
+
+- qcom,current-limit-microamp
+	Usage:        optional
+	Value type:   <u32>
+	Definition:   uA; per-string current limit; value from 0 to 30000 with
+		      2500 uA step. Default 25 mA.
 
 - qcom,current-boost-limit
 	Usage:        optional
 	Value type:   <u32>
 	Definition:   mA; boost current limit.
 		      For pm8941: one of: 105, 385, 525, 805, 980, 1260, 1400,
-		      1680. Default: 805 mA
+		      1680. Default: 805 mA.
 		      For pmi8998: one of: 105, 280, 450, 620, 970, 1150, 1300,
-		      1500. Default: 970 mA
+		      1500. Default: 970 mA.
 
 - qcom,switching-freq
 	Usage:        optional
@@ -76,15 +80,62 @@ platforms. The PMIC is connected to the host processor via SPMI bus.
 	Usage:        optional
 	Value type:   <u32>
 	Definition:   V; Over-voltage protection limit; one of:
-		      27, 29, 32, 35. default: 29V
+		      27, 29, 32, 35. Default: 29V
 		      This property is supported only for PM8941.
 
+- qcom,ovp-millivolt
+	Usage:        optional
+	Value type:   <u32>
+	Definition:   mV; Over-voltage protection limit;
+		      For pmi8998: one of 18100, 19600, 29600, 31100.
+		      Default 29600 mV.
+		      If this property is not specified for PM8941, it
+		      falls back to "qcom,ovp" property.
+
 - qcom,num-strings
 	Usage:        optional
 	Value type:   <u32>
 	Definition:   #; number of led strings attached;
-		      value from 1 to 3. default: 2
-		      This property is supported only for PM8941.
+		      value: For PM8941 from 1 to 3. Default: 2
+			     For PMI8998 from 1 to 4.
+
+- interrupts
+	Usage:        optional
+	Value type:   <prop encoded array>
+	Definition:   Interrupts associated with WLED. This should be
+		      "short" and "ovp" interrupts. Interrupts can be
+		      specified as per the encoding listed under
+		      Documentation/devicetree/bindings/spmi/
+		      qcom,spmi-pmic-arb.txt.
+
+- interrupt-names
+	Usage:        optional
+	Value type:   <string>
+	Definition:   Interrupt names associated with the interrupts.
+		      Must be "short" and "ovp". The short circuit detection
+		      is not supported for PM8941.
+
+- qcom,enabled-strings
+	Usage:        optional
+	Value tyoe:   <u32 array>
+	Definition:   Array of the WLED strings numbered from 0 to 3. Each
+		      string of leds are operated individually. Specify the
+		      list of strings used by the device. Any combination of
+		      led strings can be used.
+
+- qcom,external-pfet
+	Usage:        optional
+	Value type:   <bool>
+	Definition:   Specify if external PFET control for short circuit
+		      protection is used. This property is supported only
+		      for PMI8998.
+
+- qcom,auto-string-detection
+	Usage:        optional
+	Value type:   <bool>
+	Definition:   Enables auto-detection of the WLED string configuration.
+		      This feature is not supported for PM8941.
+
 
 Example:
 
@@ -99,4 +150,5 @@ pm8941-wled at d800 {
 	qcom,switching-freq = <1600>;
 	qcom,ovp = <29>;
 	qcom,num-strings = <2>;
+	qcom,enabled-strings = <0 1>;
 };
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
 a Linux Foundation Collaborative Project