[PATCH] backlight: l4f00242t03: Convert to GPIO descriptors
Linus Walleij
linus.walleij at linaro.org
Wed Apr 15 12:14:49 UTC 2020
This converts the l4f00242t03 backlight driver to use GPIO
descriptors and switches the two Freescale i.MX boards over
to passing descriptors instead of global GPIO numbers.
We use the typical names "enable" and "reset" as found in
the device tree bindings for panel GPIOs.
This saves a lot of code in the driver and makes it possible
to get rid of the platform data header altogether.
Cc: Sascha Hauer <s.hauer at pengutronix.de>
Cc: Anson Huang <Anson.Huang at nxp.com>
Cc: Shawn Guo <shawnguo at kernel.org>
Cc: Pengutronix Kernel Team <kernel at pengutronix.de>
Cc: Fabio Estevam <festevam at gmail.com>
Cc: NXP Linux Team <linux-imx at nxp.com>
Cc: Alberto Panizzo <maramaopercheseimorto at gmail.com>
Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
---
i.MX folks: please test if you can or at least ACK so Lee
knows if this is OK for you.
---
arch/arm/mach-imx/mach-mx27_3ds.c | 21 +++++++++----
arch/arm/mach-imx/mach-mx31_3ds.c | 24 +++++++++++---
drivers/video/backlight/l4f00242t03.c | 45 +++++++++++----------------
include/linux/spi/l4f00242t03.h | 17 ----------
4 files changed, 52 insertions(+), 55 deletions(-)
delete mode 100644 include/linux/spi/l4f00242t03.h
diff --git a/arch/arm/mach-imx/mach-mx27_3ds.c b/arch/arm/mach-imx/mach-mx27_3ds.c
index 7b8325fb5b41..1da5f07952ac 100644
--- a/arch/arm/mach-imx/mach-mx27_3ds.c
+++ b/arch/arm/mach-imx/mach-mx27_3ds.c
@@ -13,6 +13,7 @@
#include <linux/platform_device.h>
#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
#include <linux/irq.h>
#include <linux/usb/otg.h>
#include <linux/usb/ulpi.h>
@@ -20,8 +21,6 @@
#include <linux/mfd/mc13783.h>
#include <linux/spi/spi.h>
#include <linux/regulator/machine.h>
-#include <linux/spi/l4f00242t03.h>
-
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
@@ -351,9 +350,19 @@ static const struct imx_fb_platform_data mx27_3ds_fb_data __initconst = {
};
/* LCD */
-static struct l4f00242t03_pdata mx27_3ds_lcd_pdata = {
- .reset_gpio = LCD_RESET,
- .data_enable_gpio = LCD_ENABLE,
+static struct gpiod_lookup_table mx27_3ds_lcd_gpiod_table = {
+ .dev_id = "spi0.0", /* Bus 0 chipselect 0 */
+ .table = {
+ /*
+ * The i.MX27 has the i.MX21 GPIO controller, the GPIOs
+ * numbered IMX_GPIO_NR(1, 3) and IMX_GPIO_NR(1, 31)
+ * are in "bank 1" which is subtracted by one in the macro
+ * so these are actually bank 0 on "imx21-gpio.0".
+ */
+ GPIO_LOOKUP("imx21-gpio.0", 3, "reset", GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP("imx21-gpio.0", 31, "enable", GPIO_ACTIVE_HIGH),
+ { },
+ },
};
static struct spi_board_info mx27_3ds_spi_devs[] __initdata = {
@@ -370,7 +379,6 @@ static struct spi_board_info mx27_3ds_spi_devs[] __initdata = {
.max_speed_hz = 5000000,
.bus_num = 0,
.chip_select = 0, /* SS0 */
- .platform_data = &mx27_3ds_lcd_pdata,
},
};
@@ -416,6 +424,7 @@ static void __init mx27pdk_late_init(void)
if (!otg_mode_host)
imx27_add_fsl_usb2_udc(&otg_device_pdata);
+ gpiod_add_lookup_table(&mx27_3ds_lcd_gpiod_table);
mx27_3ds_spi_devs[0].irq = gpio_to_irq(PMIC_INT);
spi_register_board_info(mx27_3ds_spi_devs,
ARRAY_SIZE(mx27_3ds_spi_devs));
diff --git a/arch/arm/mach-imx/mach-mx31_3ds.c b/arch/arm/mach-imx/mach-mx31_3ds.c
index 716d2ad51103..e81386190479 100644
--- a/arch/arm/mach-imx/mach-mx31_3ds.c
+++ b/arch/arm/mach-imx/mach-mx31_3ds.c
@@ -10,10 +10,10 @@
#include <linux/clk.h>
#include <linux/irq.h>
#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
#include <linux/platform_device.h>
#include <linux/mfd/mc13783.h>
#include <linux/spi/spi.h>
-#include <linux/spi/l4f00242t03.h>
#include <linux/regulator/machine.h>
#include <linux/usb/otg.h>
#include <linux/usb/ulpi.h>
@@ -160,9 +160,23 @@ static struct mx3fb_platform_data mx3fb_pdata __initdata = {
};
/* LCD */
-static struct l4f00242t03_pdata mx31_3ds_l4f00242t03_pdata = {
- .reset_gpio = IOMUX_TO_GPIO(MX31_PIN_LCS1),
- .data_enable_gpio = IOMUX_TO_GPIO(MX31_PIN_SER_RS),
+static struct gpiod_lookup_table mx31_3ds_lcd_gpiod_table = {
+ .dev_id = "spi0.2", /* Bus 0 chipselect 2 */
+ .table = {
+ /*
+ * "reset" has IOMUX_TO_GPIO(IOMUX_PIN(88, 28)).
+ * The macro only shifts 88 to bits 9..16 and then
+ * mask it and shift it back. The GPIO number is 88.
+ * 88 is 2*32+24
+ */
+ GPIO_LOOKUP("imx31-gpio.2", 24, "reset", GPIO_ACTIVE_HIGH),
+ /*
+ * Same reasoning as above for
+ * IOMUX_TO_GPIO(IOMUX_PIN(89, 27), pin 89 is 2*32+25.
+ */
+ GPIO_LOOKUP("imx31-gpio.2", 25, "enable", GPIO_ACTIVE_HIGH),
+ { },
+ },
};
/*
@@ -387,7 +401,6 @@ static struct spi_board_info mx31_3ds_spi_devs[] __initdata = {
.max_speed_hz = 5000000,
.bus_num = 0,
.chip_select = 2, /* SS2 */
- .platform_data = &mx31_3ds_l4f00242t03_pdata,
},
};
@@ -566,6 +579,7 @@ static void __init mx31_3ds_init(void)
static void __init mx31_3ds_late(void)
{
+ gpiod_add_lookup_table(&mx31_3ds_lcd_gpiod_table);
mx31_3ds_spi_devs[0].irq = gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_3));
spi_register_board_info(mx31_3ds_spi_devs,
ARRAY_SIZE(mx31_3ds_spi_devs));
diff --git a/drivers/video/backlight/l4f00242t03.c b/drivers/video/backlight/l4f00242t03.c
index 8554b4aa980c..46f97d1c3d21 100644
--- a/drivers/video/backlight/l4f00242t03.c
+++ b/drivers/video/backlight/l4f00242t03.c
@@ -14,13 +14,11 @@
#include <linux/kernel.h>
#include <linux/delay.h>
#include <linux/module.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/lcd.h>
#include <linux/slab.h>
#include <linux/regulator/consumer.h>
-
#include <linux/spi/spi.h>
-#include <linux/spi/l4f00242t03.h>
struct l4f00242t03_priv {
struct spi_device *spi;
@@ -28,16 +26,18 @@ struct l4f00242t03_priv {
int lcd_state;
struct regulator *io_reg;
struct regulator *core_reg;
+ struct gpio_desc *reset;
+ struct gpio_desc *enable;
};
-static void l4f00242t03_reset(unsigned int gpio)
+static void l4f00242t03_reset(struct gpio_desc *gpiod)
{
pr_debug("l4f00242t03_reset.\n");
- gpio_set_value(gpio, 1);
+ gpiod_set_value(gpiod, 1);
mdelay(100);
- gpio_set_value(gpio, 0);
+ gpiod_set_value(gpiod, 0);
mdelay(10); /* tRES >= 100us */
- gpio_set_value(gpio, 1);
+ gpiod_set_value(gpiod, 1);
mdelay(20);
}
@@ -45,7 +45,6 @@ static void l4f00242t03_reset(unsigned int gpio)
static void l4f00242t03_lcd_init(struct spi_device *spi)
{
- struct l4f00242t03_pdata *pdata = dev_get_platdata(&spi->dev);
struct l4f00242t03_priv *priv = spi_get_drvdata(spi);
const u16 cmd[] = { 0x36, param(0), 0x3A, param(0x60) };
int ret;
@@ -76,21 +75,20 @@ static void l4f00242t03_lcd_init(struct spi_device *spi)
return;
}
- l4f00242t03_reset(pdata->reset_gpio);
+ l4f00242t03_reset(priv->reset);
- gpio_set_value(pdata->data_enable_gpio, 1);
+ gpiod_set_value(priv->enable, 1);
msleep(60);
spi_write(spi, (const u8 *)cmd, ARRAY_SIZE(cmd) * sizeof(u16));
}
static void l4f00242t03_lcd_powerdown(struct spi_device *spi)
{
- struct l4f00242t03_pdata *pdata = dev_get_platdata(&spi->dev);
struct l4f00242t03_priv *priv = spi_get_drvdata(spi);
dev_dbg(&spi->dev, "Powering down LCD\n");
- gpio_set_value(pdata->data_enable_gpio, 0);
+ gpiod_set_value(priv->enable, 0);
regulator_disable(priv->io_reg);
regulator_disable(priv->core_reg);
@@ -168,13 +166,6 @@ static struct lcd_ops l4f_ops = {
static int l4f00242t03_probe(struct spi_device *spi)
{
struct l4f00242t03_priv *priv;
- struct l4f00242t03_pdata *pdata = dev_get_platdata(&spi->dev);
- int ret;
-
- if (pdata == NULL) {
- dev_err(&spi->dev, "Uninitialized platform data.\n");
- return -EINVAL;
- }
priv = devm_kzalloc(&spi->dev, sizeof(struct l4f00242t03_priv),
GFP_KERNEL);
@@ -187,21 +178,21 @@ static int l4f00242t03_probe(struct spi_device *spi)
priv->spi = spi;
- ret = devm_gpio_request_one(&spi->dev, pdata->reset_gpio,
- GPIOF_OUT_INIT_HIGH, "lcd l4f00242t03 reset");
- if (ret) {
+ priv->reset = devm_gpiod_get(&spi->dev, "reset", GPIOD_OUT_HIGH);
+ if (IS_ERR(priv->reset)) {
dev_err(&spi->dev,
"Unable to get the lcd l4f00242t03 reset gpio.\n");
- return ret;
+ return PTR_ERR(priv->reset);
}
+ gpiod_set_consumer_name(priv->reset, "lcd l4f00242t03 reset");
- ret = devm_gpio_request_one(&spi->dev, pdata->data_enable_gpio,
- GPIOF_OUT_INIT_LOW, "lcd l4f00242t03 data enable");
- if (ret) {
+ priv->enable = devm_gpiod_get(&spi->dev, "enable", GPIOD_OUT_LOW);
+ if (IS_ERR(priv->enable)) {
dev_err(&spi->dev,
"Unable to get the lcd l4f00242t03 data en gpio.\n");
- return ret;
+ return PTR_ERR(priv->enable);
}
+ gpiod_set_consumer_name(priv->enable, "lcd l4f00242t03 data enable");
priv->io_reg = devm_regulator_get(&spi->dev, "vdd");
if (IS_ERR(priv->io_reg)) {
diff --git a/include/linux/spi/l4f00242t03.h b/include/linux/spi/l4f00242t03.h
deleted file mode 100644
index 831a5de7a0e2..000000000000
--- a/include/linux/spi/l4f00242t03.h
+++ /dev/null
@@ -1,17 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * l4f00242t03.h -- Platform glue for Epson L4F00242T03 LCD
- *
- * Copyright (c) 2009 Alberto Panizzo <maramaopercheseimorto at gmail.com>
- * Based on Marek Vasut work in lms283gf05.h
-*/
-
-#ifndef _INCLUDE_LINUX_SPI_L4F00242T03_H_
-#define _INCLUDE_LINUX_SPI_L4F00242T03_H_
-
-struct l4f00242t03_pdata {
- unsigned int reset_gpio;
- unsigned int data_enable_gpio;
-};
-
-#endif /* _INCLUDE_LINUX_SPI_L4F00242T03_H_ */
--
2.25.2
More information about the dri-devel
mailing list