[PATCH 3/3 v2] backlight: Add Kinetic KTD253 backlight driver
Daniel Thompson
daniel.thompson at linaro.org
Thu Aug 13 10:30:46 UTC 2020
On Wed, Aug 12, 2020 at 10:58:50AM +0200, Linus Walleij wrote:
> The Kinetic KTD253 backlight driver is controlled with a
> single GPIO line, but still supports a range of brightness
> settings by sending fast pulses on the line.
>
> This is based off the source code release for the Samsung
> GT-S7710 mobile phone.
>
> Cc: Sam Ravnborg <sam at ravnborg.org>
> Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson at linaro.org>
(although note that Sam has some patches that introduce new
APIs that this driver should, but cannot yet, use)
Daniel.
> ---
> ChangeLog v1->v2:
> - Expose the 32 actual hardware levels of brightness directly
> instead of using an interpolated "brightness" table.
> - Use the new backlight_get_brightness() helper.
> - Call backlight_update_status() in probe instead of calling
> local functions to sync brightness.
> - Sort includes alphabetically.
> - Name the GPIO line "enable" and grab that in accordance
> with the change to the DT bindings.
> ---
> MAINTAINERS | 6 +
> drivers/video/backlight/Kconfig | 8 +
> drivers/video/backlight/Makefile | 1 +
> drivers/video/backlight/ktd253-backlight.c | 198 +++++++++++++++++++++
> 4 files changed, 213 insertions(+)
> create mode 100644 drivers/video/backlight/ktd253-backlight.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index e627ed60d75a..4c93e3a7be11 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -9711,6 +9711,12 @@ F: Documentation/admin-guide/auxdisplay/ks0108.rst
> F: drivers/auxdisplay/ks0108.c
> F: include/linux/ks0108.h
>
> +KTD253 BACKLIGHT DRIVER
> +M: Linus Walleij <linus.walleij at linaro.org>
> +S: Maintained
> +F: Documentation/devicetree/bindings/leds/backlight/kinetic,ktd253.yaml
> +F: drivers/video/backlight/ktd253-backlight.c
> +
> L3MDEV
> M: David Ahern <dsahern at kernel.org>
> L: netdev at vger.kernel.org
> diff --git a/drivers/video/backlight/Kconfig b/drivers/video/backlight/Kconfig
> index 87f9fc238d28..d83c87b902c1 100644
> --- a/drivers/video/backlight/Kconfig
> +++ b/drivers/video/backlight/Kconfig
> @@ -182,6 +182,14 @@ config BACKLIGHT_IPAQ_MICRO
> computers. Say yes if you have one of the h3100/h3600/h3700
> machines.
>
> +config BACKLIGHT_KTD253
> + tristate "Backlight Driver for Kinetic KTD253"
> + depends on GPIOLIB || COMPILE_TEST
> + help
> + Say y to enabled the backlight driver for the Kinetic KTD253
> + which is a 1-wire GPIO-controlled backlight found in some mobile
> + phones.
> +
> config BACKLIGHT_LM3533
> tristate "Backlight Driver for LM3533"
> depends on MFD_LM3533
> diff --git a/drivers/video/backlight/Makefile b/drivers/video/backlight/Makefile
> index 13463b99f1f9..685f3f1ca4df 100644
> --- a/drivers/video/backlight/Makefile
> +++ b/drivers/video/backlight/Makefile
> @@ -35,6 +35,7 @@ obj-$(CONFIG_BACKLIGHT_GPIO) += gpio_backlight.o
> obj-$(CONFIG_BACKLIGHT_HP680) += hp680_bl.o
> obj-$(CONFIG_BACKLIGHT_HP700) += jornada720_bl.o
> obj-$(CONFIG_BACKLIGHT_IPAQ_MICRO) += ipaq_micro_bl.o
> +obj-$(CONFIG_BACKLIGHT_KTD253) += ktd253-backlight.o
> obj-$(CONFIG_BACKLIGHT_LM3533) += lm3533_bl.o
> obj-$(CONFIG_BACKLIGHT_LM3630A) += lm3630a_bl.o
> obj-$(CONFIG_BACKLIGHT_LM3639) += lm3639_bl.o
> diff --git a/drivers/video/backlight/ktd253-backlight.c b/drivers/video/backlight/ktd253-backlight.c
> new file mode 100644
> index 000000000000..e3fee3f1f582
> --- /dev/null
> +++ b/drivers/video/backlight/ktd253-backlight.c
> @@ -0,0 +1,198 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Backlight driver for the Kinetic KTD253
> + * Based on code and know-how from the Samsung GT-S7710
> + * Gareth Phillips <gareth.phillips at samsung.com>
> + */
> +#include <linux/backlight.h>
> +#include <linux/delay.h>
> +#include <linux/err.h>
> +#include <linux/fb.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/init.h>
> +#include <linux/kernel.h>
> +#include <linux/limits.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/property.h>
> +#include <linux/slab.h>
> +
> +/* Current ratio is n/32 from 1/32 to 32/32 */
> +#define KTD253_MIN_RATIO 1
> +#define KTD253_MAX_RATIO 32
> +#define KTD253_DEFAULT_RATIO 13
> +
> +#define KTD253_T_LOW_NS (200 + 10) /* Additional 10ns as safety factor */
> +#define KTD253_T_HIGH_NS (200 + 10) /* Additional 10ns as safety factor */
> +#define KTD253_T_OFF_MS 3
> +
> +struct ktd253_backlight {
> + struct device *dev;
> + struct backlight_device *bl;
> + struct gpio_desc *gpiod;
> + u16 ratio;
> +};
> +
> +static int ktd253_backlight_update_status(struct backlight_device *bl)
> +{
> + struct ktd253_backlight *ktd253 = bl_get_data(bl);
> + int brightness = backlight_get_brightness(bl);
> + u16 target_ratio;
> + u16 current_ratio = ktd253->ratio;
> + unsigned long flags;
> +
> + dev_dbg(ktd253->dev, "new brightness/ratio: %d/32\n", brightness);
> +
> + target_ratio = brightness;
> +
> + if (target_ratio == current_ratio)
> + /* This is already right */
> + return 0;
> +
> + if (target_ratio == 0) {
> + gpiod_set_value_cansleep(ktd253->gpiod, 0);
> + /*
> + * We need to keep the GPIO low for at least this long
> + * to actually switch the KTD253 off.
> + */
> + msleep(KTD253_T_OFF_MS);
> + ktd253->ratio = 0;
> + return 0;
> + }
> +
> + if (current_ratio == 0) {
> + gpiod_set_value_cansleep(ktd253->gpiod, 1);
> + ndelay(KTD253_T_HIGH_NS);
> + /* We always fall back to this when we power on */
> + current_ratio = KTD253_MAX_RATIO;
> + }
> +
> + /*
> + * WARNING:
> + * The loop to set the correct current level is performed
> + * with interrupts disabled as it is timing critical.
> + * The maximum number of cycles of the loop is 32
> + * so the time taken will be (T_LOW_NS + T_HIGH_NS + loop_time) * 32,
> + */
> + local_irq_save(flags);
> + while (current_ratio != target_ratio) {
> + /*
> + * These GPIO operations absolutely can NOT sleep so no
> + * _cansleep suffixes, and no using GPIO expanders on
> + * slow buses for this!
> + */
> + gpiod_set_value(ktd253->gpiod, 0);
> + ndelay(KTD253_T_LOW_NS);
> + gpiod_set_value(ktd253->gpiod, 1);
> + ndelay(KTD253_T_HIGH_NS);
> + /* After 1/32 we loop back to 32/32 */
> + if (current_ratio == KTD253_MIN_RATIO)
> + current_ratio = KTD253_MAX_RATIO;
> + else
> + current_ratio--;
> + }
> + local_irq_restore(flags);
> + ktd253->ratio = current_ratio;
> +
> + dev_dbg(ktd253->dev, "new ratio set to %d/32\n", target_ratio);
> +
> + return 0;
> +}
> +
> +static const struct backlight_ops ktd253_backlight_ops = {
> + .options = BL_CORE_SUSPENDRESUME,
> + .update_status = ktd253_backlight_update_status,
> +};
> +
> +static int ktd253_backlight_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct backlight_device *bl;
> + struct ktd253_backlight *ktd253;
> + u32 max_brightness;
> + u32 brightness;
> + int ret;
> +
> + ktd253 = devm_kzalloc(dev, sizeof(*ktd253), GFP_KERNEL);
> + if (!ktd253)
> + return -ENOMEM;
> + ktd253->dev = dev;
> +
> + ret = device_property_read_u32(dev, "max-brightness", &max_brightness);
> + if (ret)
> + max_brightness = KTD253_MAX_RATIO;
> + if (max_brightness > KTD253_MAX_RATIO) {
> + /* Clamp brightness to hardware max */
> + dev_err(dev, "illegal max brightness specified\n");
> + max_brightness = KTD253_MAX_RATIO;
> + }
> +
> + ret = device_property_read_u32(dev, "default-brightness", &brightness);
> + if (ret)
> + brightness = KTD253_DEFAULT_RATIO;
> + if (brightness > max_brightness) {
> + /* Clamp default brightness to max brightness */
> + dev_err(dev, "default brightness exceeds max brightness\n");
> + brightness = max_brightness;
> + }
> +
> + if (brightness)
> + /* This will be the default ratio when the KTD253 is enabled */
> + ktd253->ratio = KTD253_MAX_RATIO;
> + else
> + ktd253->ratio = 0;
> +
> + ktd253->gpiod = devm_gpiod_get(dev, "enable",
> + brightness ? GPIOD_OUT_HIGH :
> + GPIOD_OUT_LOW);
> + if (IS_ERR(ktd253->gpiod)) {
> + ret = PTR_ERR(ktd253->gpiod);
> + if (ret != -EPROBE_DEFER)
> + dev_err(dev, "gpio line missing or invalid.\n");
> + return ret;
> + }
> + gpiod_set_consumer_name(ktd253->gpiod, dev_name(dev));
> +
> + bl = devm_backlight_device_register(dev, dev_name(dev), dev, ktd253,
> + &ktd253_backlight_ops, NULL);
> + if (IS_ERR(bl)) {
> + dev_err(dev, "failed to register backlight\n");
> + return PTR_ERR(bl);
> + }
> + bl->props.max_brightness = max_brightness;
> + /* When we just enable the GPIO line we set max brightness */
> + if (brightness) {
> + bl->props.brightness = brightness;
> + bl->props.power = FB_BLANK_UNBLANK;
> + } else {
> + bl->props.brightness = 0;
> + bl->props.power = FB_BLANK_POWERDOWN;
> + }
> +
> + ktd253->bl = bl;
> + platform_set_drvdata(pdev, bl);
> + backlight_update_status(bl);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id ktd253_backlight_of_match[] = {
> + { .compatible = "kinetic,ktd253" },
> + { /* sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, ktd253_backlight_of_match);
> +
> +static struct platform_driver ktd253_backlight_driver = {
> + .driver = {
> + .name = "ktd253-backlight",
> + .of_match_table = ktd253_backlight_of_match,
> + },
> + .probe = ktd253_backlight_probe,
> +};
> +module_platform_driver(ktd253_backlight_driver);
> +
> +MODULE_AUTHOR("Linus Walleij <linus.walleij at linaro.org>");
> +MODULE_DESCRIPTION("Kinetic KTD253 Backlight Driver");
> +MODULE_LICENSE("GPL");
> +MODULE_ALIAS("platform:ktd253-backlight");
> --
> 2.26.2
>
More information about the dri-devel
mailing list