[PATCH v7 1/4] dt-bindings: display: mediatek: update dpi supported chips

[CK Hu]

Hi, Jitao:

On Tue, 2020-02-25 at 14:46 +0800, Jitao Shi wrote:
> Add decriptions about supported chips, including MT2701 & MT8173 &
> mt8183

descriptions

> 
> 1. Add more chips support. ex. MT2701 & MT8173 & MT8183
> 2. Add property "pinctrl-names" to swap pin mode between gpio and dpi mode. Set
>    pin mode to gpio oupput-low to avoid leakage current when dpi disable.
> 3. Add property "pclk-sample" to config the dpi sample on falling (0),
>    rising (1), both falling and rising (2).

The title is just about supported chips, so I prefer you move other
modification to another patch. Of course, you could use a more rough
title to include all what you do so you need not to break this patch.

> 
> Signed-off-by: Jitao Shi <jitao.shi at mediatek.com>
> ---
>  .../bindings/display/mediatek/mediatek,dpi.txt         | 10 ++++++++++
>  1 file changed, 10 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> index b6a7e7397b8b..0dee4f7a227e 100644
> --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> @@ -7,6 +7,7 @@ output bus.
>  
>  Required properties:
>  - compatible: "mediatek,<chip>-dpi"
> +  the supported chips are mt2701 , mt8173 and mt8183.
>  - reg: Physical base address and length of the controller's registers
>  - interrupts: The interrupt signal from the function block.
>  - clocks: device clocks
> @@ -16,6 +17,11 @@ Required properties:
>    Documentation/devicetree/bindings/graph.txt. This port should be connected
>    to the input port of an attached HDMI or LVDS encoder chip.
>  
> +Optional properties:
> +- pinctrl-names: Contain "gpiomode" and "dpimode".
> +- pclk-sample: 0: sample in falling edge, 1: sample in rising edge, 2: sample
> +  in both falling and rising edge.

pinctrl-names & pclk-sample are defined in another document, please list
the reference document, [1] is the sample. For pclk-sample, I think you
should modify [2] to add 'sampling in both failing and rising edge'.

[1] Documentation/devicetree/bindings/display/bridge/ti,tfp410.txt
[2] Documentation/devicetree/bindings/media/video-interfaces.txt

> +
>  Example:
>  
>  dpi0: dpi at 1401d000 {
> @@ -26,6 +32,10 @@ dpi0: dpi at 1401d000 {
>  		 <&mmsys CLK_MM_DPI_ENGINE>,
>  		 <&apmixedsys CLK_APMIXED_TVDPLL>;
>  	clock-names = "pixel", "engine", "pll";
> +	pclk-sample = 0;

I think you should move pclk-sample into the port node according to [2].

Regards,
CK

> +	pinctrl-names = "gpiomode", "dpimode";
> +	pinctrl-0 = <&dpi_pin_gpio>;
> +	pinctrl-1 = <&dpi_pin_func>;
>  
>  	port {
>  		dpi0_out: endpoint {