[PATCH v4 05/15] drm/bridge: tc358767: add detect bridge operation
Laurent Pinchart
laurent.pinchart at ideasonboard.com
Sun Jul 26 21:27:40 UTC 2020
Hi Sam,
Thank you for the patch.
On Sun, Jul 26, 2020 at 10:33:14PM +0200, Sam Ravnborg wrote:
> Prepare the bridge driver for chained operation by adding
> support for the detect operation.
>
> v2:
> - Do not announce detect operation if there is no hpd pin (Laurent)
>
> Signed-off-by: Sam Ravnborg <sam at ravnborg.org>
> Cc: Andrzej Hajda <a.hajda at samsung.com>
> Cc: Neil Armstrong <narmstrong at baylibre.com>
> Cc: Laurent Pinchart <Laurent.pinchart at ideasonboard.com>
> Cc: Jonas Karlman <jonas at kwiboo.se>
> Cc: Jernej Skrabec <jernej.skrabec at siol.net>
> ---
> drivers/gpu/drm/bridge/tc358767.c | 30 ++++++++++++++++++++----------
> 1 file changed, 20 insertions(+), 10 deletions(-)
>
> diff --git a/drivers/gpu/drm/bridge/tc358767.c b/drivers/gpu/drm/bridge/tc358767.c
> index c2777b226c75..e8ba713bedac 100644
> --- a/drivers/gpu/drm/bridge/tc358767.c
> +++ b/drivers/gpu/drm/bridge/tc358767.c
> @@ -1369,21 +1369,13 @@ static const struct drm_connector_helper_funcs tc_connector_helper_funcs = {
> .get_modes = tc_connector_get_modes,
> };
>
> -static enum drm_connector_status tc_connector_detect(struct drm_connector *connector,
> - bool force)
> +static enum drm_connector_status tc_bridge_detect(struct drm_bridge *bridge)
> {
> - struct tc_data *tc = connector_to_tc(connector);
> + struct tc_data *tc = bridge_to_tc(bridge);
> bool conn;
> u32 val;
> int ret;
>
> - if (tc->hpd_pin < 0) {
> - if (tc->panel)
> - return connector_status_connected;
> - else
> - return connector_status_unknown;
> - }
> -
> ret = regmap_read(tc->regmap, GPIOI, &val);
> if (ret)
> return connector_status_unknown;
> @@ -1396,6 +1388,20 @@ static enum drm_connector_status tc_connector_detect(struct drm_connector *conne
> return connector_status_disconnected;
> }
>
> +static enum drm_connector_status
> +tc_connector_detect(struct drm_connector *connector, bool force)
> +{
> + struct tc_data *tc = connector_to_tc(connector);
> +
> + if (tc->hpd_pin >= 0)
> + return tc_bridge_detect(&tc->bridge);
> + else
> + if (tc->panel)
> + return connector_status_connected;
> +
> + return connector_status_unknown;
I'd write this
if (tc->hpd_pin >= 0)
return tc_bridge_detect(&tc->bridge);
if (tc->panel)
return connector_status_connected;
else
return connector_status_unknown;
Reviewed-by: Laurent Pinchart <laurent.pinchart at ideasonboard.com>
> +}
> +
> static const struct drm_connector_funcs tc_connector_funcs = {
> .detect = tc_connector_detect,
> .fill_modes = drm_helper_probe_single_connector_modes,
> @@ -1458,6 +1464,7 @@ static const struct drm_bridge_funcs tc_bridge_funcs = {
> .disable = tc_bridge_disable,
> .post_disable = tc_bridge_post_disable,
> .mode_fixup = tc_bridge_mode_fixup,
> + .detect = tc_bridge_detect,
> };
>
> static bool tc_readable_reg(struct device *dev, unsigned int reg)
> @@ -1680,6 +1687,9 @@ static int tc_probe(struct i2c_client *client, const struct i2c_device_id *id)
> return ret;
>
> tc->bridge.funcs = &tc_bridge_funcs;
> + if (tc->hpd_pin >= 0)
> + tc->bridge.ops |= DRM_BRIDGE_OP_DETECT;
> +
> tc->bridge.of_node = dev->of_node;
> drm_bridge_add(&tc->bridge);
>
--
Regards,
Laurent Pinchart
More information about the dri-devel
mailing list