[PATCH v5 3/5] drm/bridge: tc358767: add drm_panel_bridge support

Laurent Pinchart laurent.pinchart at ideasonboard.com
Mon Jul 27 17:12:43 UTC 2020


Hi Sam,

Thank you for the patch.

On Mon, Jul 27, 2020 at 07:03:18PM +0200, Sam Ravnborg wrote:
> With the bridge operations implemented the last step to prepare
> this driver for a chained setup is the use of the bridge panel driver.
> 
> The bridge panel driver is only used when a port at 2 is present in
> the DT. So when the display driver requests a connector
> support both situations:
> - connector created by bridge panel driver
> - connector created by this driver
> 
> And on top, support that the display driver creates the connector,
> which is the preferred setup.
> 
> Note: the bridge panel will use the connector type from the panel.
> 
> v3:
>   - Fix wrong logic in connector creation (Laurent)
> 
> v2:
>   - Merge connector and drm_panel_bridge patches
>     and fix so we do not create two connectors (Laurent)
> 
> Signed-off-by: Sam Ravnborg <sam at ravnborg.org>
> Cc: Laurent Pinchart <laurent.pinchart at ideasonboard.com>
> Cc: Andrzej Hajda <a.hajda at samsung.com>
> Cc: Neil Armstrong <narmstrong at baylibre.com>
> Cc: Jonas Karlman <jonas at kwiboo.se>
> Cc: Jernej Skrabec <jernej.skrabec at siol.net>
> ---
>  drivers/gpu/drm/bridge/tc358767.c | 70 +++++++++++++++----------------
>  1 file changed, 35 insertions(+), 35 deletions(-)
> 
> diff --git a/drivers/gpu/drm/bridge/tc358767.c b/drivers/gpu/drm/bridge/tc358767.c
> index b26c669f3e91..cbad2607ab43 100644
> --- a/drivers/gpu/drm/bridge/tc358767.c
> +++ b/drivers/gpu/drm/bridge/tc358767.c
> @@ -244,8 +244,8 @@ struct tc_data {
>  	struct drm_dp_aux	aux;
>  
>  	struct drm_bridge	bridge;
> +	struct drm_bridge	*panel_bridge;
>  	struct drm_connector	connector;
> -	struct drm_panel	*panel;
>  
>  	/* link settings */
>  	struct tc_edp_link	link;
> @@ -1234,13 +1234,6 @@ static int tc_stream_disable(struct tc_data *tc)
>  	return 0;
>  }
>  
> -static void tc_bridge_pre_enable(struct drm_bridge *bridge)
> -{
> -	struct tc_data *tc = bridge_to_tc(bridge);
> -
> -	drm_panel_prepare(tc->panel);
> -}
> -
>  static void tc_bridge_enable(struct drm_bridge *bridge)
>  {
>  	struct tc_data *tc = bridge_to_tc(bridge);
> @@ -1264,8 +1257,6 @@ static void tc_bridge_enable(struct drm_bridge *bridge)
>  		tc_main_link_disable(tc);
>  		return;
>  	}
> -
> -	drm_panel_enable(tc->panel);
>  }
>  
>  static void tc_bridge_disable(struct drm_bridge *bridge)
> @@ -1273,8 +1264,6 @@ static void tc_bridge_disable(struct drm_bridge *bridge)
>  	struct tc_data *tc = bridge_to_tc(bridge);
>  	int ret;
>  
> -	drm_panel_disable(tc->panel);
> -
>  	ret = tc_stream_disable(tc);
>  	if (ret < 0)
>  		dev_err(tc->dev, "main link stream stop error: %d\n", ret);
> @@ -1284,13 +1273,6 @@ static void tc_bridge_disable(struct drm_bridge *bridge)
>  		dev_err(tc->dev, "main link disable error: %d\n", ret);
>  }
>  
> -static void tc_bridge_post_disable(struct drm_bridge *bridge)
> -{
> -	struct tc_data *tc = bridge_to_tc(bridge);
> -
> -	drm_panel_unprepare(tc->panel);
> -}
> -
>  static bool tc_bridge_mode_fixup(struct drm_bridge *bridge,
>  				 const struct drm_display_mode *mode,
>  				 struct drm_display_mode *adj)
> @@ -1354,9 +1336,11 @@ static int tc_connector_get_modes(struct drm_connector *connector)
>  		return 0;
>  	}
>  
> -	num_modes = drm_panel_get_modes(tc->panel, connector);
> -	if (num_modes > 0)
> -		return num_modes;
> +	if (tc->panel_bridge) {
> +		num_modes = drm_bridge_get_modes(tc->panel_bridge, connector);
> +		if (num_modes > 0)
> +			return num_modes;
> +	}
>  
>  	edid = tc_get_edid(&tc->bridge, connector);
>  	num_modes = drm_add_edid_modes(connector, edid);
> @@ -1396,7 +1380,7 @@ tc_connector_detect(struct drm_connector *connector, bool force)
>  	if (tc->hpd_pin >= 0)
>  		return tc_bridge_detect(&tc->bridge);
>  
> -	if (tc->panel)
> +	if (tc->panel_bridge)
>  		return connector_status_connected;
>  	else
>  		return connector_status_unknown;
> @@ -1419,16 +1403,23 @@ static int tc_bridge_attach(struct drm_bridge *bridge,
>  	struct drm_device *drm = bridge->dev;
>  	int ret;
>  
> -	if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR) {
> -		DRM_ERROR("Fix bridge driver to make connector optional!");
> -		return -EINVAL;
> +	if (tc->panel_bridge) {
> +		enum drm_bridge_attach_flags panel_flags;
> +
> +		/* If a connector is required then this driver shall create it */
> +		panel_flags = flags | DRM_BRIDGE_ATTACH_NO_CONNECTOR;
> +		ret = drm_bridge_attach(tc->bridge.encoder, tc->panel_bridge,
> +					&tc->bridge, panel_flags);

You could write this

					flags | DRM_BRIDGE_ATTACH_NO_CONNECTOR);

and drop the panel_flags variable.

Reviewed-by: Laurent Pinchart <laurent.pinchart at ideasonboard.com>

> +		if (ret)
> +			return ret;
>  	}
>  
> +	if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)
> +		return 0;
> +
>  	/* Create DP/eDP connector */
>  	drm_connector_helper_add(&tc->connector, &tc_connector_helper_funcs);
> -	ret = drm_connector_init(drm, &tc->connector, &tc_connector_funcs,
> -				 tc->panel ? DRM_MODE_CONNECTOR_eDP :
> -				 DRM_MODE_CONNECTOR_DisplayPort);
> +	ret = drm_connector_init(drm, &tc->connector, &tc_connector_funcs, tc->bridge.type);
>  	if (ret)
>  		return ret;
>  
> @@ -1441,9 +1432,6 @@ static int tc_bridge_attach(struct drm_bridge *bridge,
>  					       DRM_CONNECTOR_POLL_DISCONNECT;
>  	}
>  
> -	if (tc->panel)
> -		drm_panel_attach(tc->panel, &tc->connector);
> -
>  	drm_display_info_set_bus_formats(&tc->connector.display_info,
>  					 &bus_format, 1);
>  	tc->connector.display_info.bus_flags =
> @@ -1459,10 +1447,8 @@ static const struct drm_bridge_funcs tc_bridge_funcs = {
>  	.attach = tc_bridge_attach,
>  	.mode_valid = tc_mode_valid,
>  	.mode_set = tc_bridge_mode_set,
> -	.pre_enable = tc_bridge_pre_enable,
>  	.enable = tc_bridge_enable,
>  	.disable = tc_bridge_disable,
> -	.post_disable = tc_bridge_post_disable,
>  	.mode_fixup = tc_bridge_mode_fixup,
>  	.detect = tc_bridge_detect,
>  	.get_edid = tc_get_edid,
> @@ -1555,6 +1541,7 @@ static irqreturn_t tc_irq_handler(int irq, void *arg)
>  static int tc_probe(struct i2c_client *client, const struct i2c_device_id *id)
>  {
>  	struct device *dev = &client->dev;
> +	struct drm_panel *panel;
>  	struct tc_data *tc;
>  	int ret;
>  
> @@ -1565,10 +1552,23 @@ static int tc_probe(struct i2c_client *client, const struct i2c_device_id *id)
>  	tc->dev = dev;
>  
>  	/* port at 2 is the output port */
> -	ret = drm_of_find_panel_or_bridge(dev->of_node, 2, 0, &tc->panel, NULL);
> +	ret = drm_of_find_panel_or_bridge(dev->of_node, 2, 0, &panel, NULL);
>  	if (ret && ret != -ENODEV)
>  		return ret;
>  
> +	if (panel) {
> +		struct drm_bridge *panel_bridge;
> +
> +		panel_bridge = devm_drm_panel_bridge_add(dev, panel);
> +		if (IS_ERR(panel_bridge))
> +			return PTR_ERR(panel_bridge);
> +
> +		tc->panel_bridge = panel_bridge;
> +		tc->bridge.type = DRM_MODE_CONNECTOR_eDP;
> +	} else {
> +		tc->bridge.type = DRM_MODE_CONNECTOR_DisplayPort;
> +	}
> +
>  	/* Shut down GPIO is optional */
>  	tc->sd_gpio = devm_gpiod_get_optional(dev, "shutdown", GPIOD_OUT_HIGH);
>  	if (IS_ERR(tc->sd_gpio))

-- 
Regards,

Laurent Pinchart


More information about the dri-devel mailing list