[v6] dt-bindings: msm: disp: add yaml schemas for DPU and DSI bindings
Rob Herring
robh at kernel.org
Mon Jul 27 19:41:47 UTC 2020
On Thu, Jul 16, 2020 at 08:15:28PM +0530, Krishna Manikandan wrote:
> MSM Mobile Display Subsytem (MDSS) encapsulates sub-blocks
> like DPU display controller, DSI etc. Add YAML schema
> for the device tree bindings for the same.
>
> Signed-off-by: Krishna Manikandan <mkrishn at codeaurora.org>
>
> Changes in v2:
> - Changed dpu to DPU (Sam Ravnborg)
> - Fixed indentation issues (Sam Ravnborg)
> - Added empty line between different properties (Sam Ravnborg)
> - Replaced reference txt files with their corresponding
> yaml files (Sam Ravnborg)
> - Modified the file to use "|" only when it is
> necessary (Sam Ravnborg)
>
> Changes in v3:
> - Corrected the license used (Rob Herring)
> - Added maxItems for properties (Rob Herring)
> - Dropped generic descriptions (Rob Herring)
> - Added ranges property (Rob Herring)
> - Corrected the indendation (Rob Herring)
> - Added additionalProperties (Rob Herring)
> - Split dsi file into two, one for dsi controller
> and another one for dsi phy per target (Rob Herring)
> - Corrected description for pinctrl-names (Rob Herring)
> - Corrected the examples used in yaml file (Rob Herring)
> - Delete dsi.txt and dpu.txt (Rob Herring)
>
> Changes in v4:
> - Move schema up by one level (Rob Herring)
> - Add patternProperties for mdp node (Rob Herring)
> - Corrected description of some properties (Rob Herring)
>
> Changes in v5:
> - Correct the indentation (Rob Herring)
> - Remove unnecessary description from properties (Rob Herring)
> - Correct the number of interconnect entries (Rob Herring)
> - Add interconnect names for sc7180 (Rob Herring)
> - Add description for ports (Rob Herring)
> - Remove common properties (Rob Herring)
> - Add unevalutatedProperties (Rob Herring)
> - Reference existing dsi controller yaml in the common
> dsi controller file (Rob Herring)
> - Correct the description of clock names to include only the
> clocks that are required (Rob Herring)
> - Remove properties which are already covered under the common
> binding (Rob Herring)
> - Add dsi phy supply nodes which are required for sc7180 and
> sdm845 targets (Rob Herring)
> - Add type ref for syscon-sfpb (Rob Herring)
>
> Changes in v6:
> - Fixed errors during dt_binding_check (Rob Herring)
> - Add maxItems for phys and phys-names (Rob Herring)
> - Use unevaluatedProperties wherever required (Rob Herring)
> - Removed interrupt controller from required properties for
> dsi controller (Rob Herring)
> - Add constraints for dsi-phy reg-names based on the compatible
> phy version (Rob Herring)
> - Add constraints for dsi-phy supply nodes based on the
> compatible phy version (Rob Herring)
> ---
> .../bindings/display/msm/dpu-sc7180.yaml | 236 ++++++++++++++++++++
> .../bindings/display/msm/dpu-sdm845.yaml | 216 ++++++++++++++++++
> .../devicetree/bindings/display/msm/dpu.txt | 141 ------------
> .../display/msm/dsi-common-controller.yaml | 180 +++++++++++++++
> .../display/msm/dsi-controller-sc7180.yaml | 120 ++++++++++
> .../display/msm/dsi-controller-sdm845.yaml | 120 ++++++++++
> .../bindings/display/msm/dsi-phy-sc7180.yaml | 80 +++++++
> .../bindings/display/msm/dsi-phy-sdm845.yaml | 82 +++++++
> .../devicetree/bindings/display/msm/dsi-phy.yaml | 126 +++++++++++
> .../devicetree/bindings/display/msm/dsi.txt | 246 ---------------------
> 10 files changed, 1160 insertions(+), 387 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml
> create mode 100644 Documentation/devicetree/bindings/display/msm/dpu-sdm845.yaml
> delete mode 100644 Documentation/devicetree/bindings/display/msm/dpu.txt
> create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-common-controller.yaml
> create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-controller-sc7180.yaml
> create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-controller-sdm845.yaml
> create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy-sc7180.yaml
> create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy-sdm845.yaml
> create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy.yaml
> delete mode 100644 Documentation/devicetree/bindings/display/msm/dsi.txt
>
> diff --git a/Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml b/Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml
> new file mode 100644
> index 0000000..df70393
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml
> @@ -0,0 +1,236 @@
> +# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/msm/dpu-sc7180.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Description of Qualcomm Display DPU dt properties.
> +
> +maintainers:
> + - Krishna Manikandan <mkrishn at codeaurora.org>
> +
> +description: |
> + Device tree bindings for MSM Mobile Display Subsytem(MDSS) that encapsulates
> + sub-blocks like DPU display controller, DSI and DP interfaces etc. Device tree
> + bindings of MDSS and DPU are mentioned for SC7180 target.
> +
> +properties:
> + compatible:
> + items:
> + - const: qcom,sc7180-mdss
> +
> + reg:
> + maxItems: 1
> +
> + reg-names:
> + const: mdss
> +
> + power-domains:
> + maxItems: 1
> +
> + clocks:
> + maxItems: 3
> +
> + clock-names:
> + items:
> + - const: iface
> + - const: ahb
> + - const: core
> +
> + interrupts:
> + maxItems: 1
> +
> + interrupt-controller: true
> +
> + "#interrupt-cells":
> + const: 1
> +
> + iommus:
> + maxItems: 1
> +
> + "#address-cells":
> + const: 2
> +
> + "#size-cells":
> + const: 2
> +
> + ranges: true
> +
> + interconnects:
> + description: |
> + Interconnect path specifier for MDSS according to
> + Documentation/devicetree/bindings/interconnect/interconnect.txt.
> + An entry should contain 2 paths corresponding to 2 AXI ports representing
> + source and destination ports.
> + minItems: 1
> +
> + interconnect-names:
> + description: |
> + MDSS will have 2 port names to differentiate between the
> + 2 interconnect paths defined with interconnect specifier.
> + items:
> + - const: mdp0-mem
> +
> + assigned-clocks:
> + maxItems: 1
> +
> + assigned-clock-rates:
> + maxItems: 1
> +
> +patternProperties:
> + "^mdp@[0-9a-f]+$":
> + type: object
> + description: Node containing the properties of DPU.
> +
> + properties:
> + compatible:
> + items:
> + - const: qcom,sc7180-dpu
> +
> + reg:
> + maxItems: 2
> +
> + reg-names:
> + items:
> + - const: mdp
> + - const: vbif
> +
> + clocks:
> + maxItems: 6
> +
> + clock-names:
> + description: |
> + Device clock names, must be in same order as clocks property.
> + The following clocks are required.
> + items:
> + - const: bus
> + - const: iface
> + - const: rot
> + - const: lut
> + - const: core
> + - const: vsync
> +
> + interrupts:
> + maxItems: 1
> +
> + ports:
> + type: object
> + description: |
> + Contains the list of output ports from DPU device. These ports
> + connect to interfaces that are external to the DPU hardware,
> + such as DSI, DP etc. Each output port contains an endpoint that
> + describes how it is connected to an external interface. These
> + are described by the standard properties documented in files
> + mentioned below.
> +
> + Documentation/devicetree/bindings/graph.txt
> + Documentation/devicetree/bindings/media/video-interfaces.txt
> +
> + properties:
> + port at 0:
> + type: object
> + description: DPU_INTF1 (DSI1)
> + port at 1:
> + type: object
> + description: DPU_INTF2 (DSI2)
> +
> + assigned-clocks:
> + maxItems: 4
> +
> + assigned-clock-rates:
> + maxItems: 4
> +
> +required:
> + - compatible
> + - reg
> + - reg-names
> + - power-domains
> + - clocks
> + - clock-names
> + - interrupts
> + - interrupt-controller
> + - iommus
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/clock/qcom,dispcc-sc7180.h>
> + #include <dt-bindings/clock/qcom,gcc-sc7180.h>
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + #include <dt-bindings/interconnect/qcom,sdm845.h>
> +
> + soc: soc {
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + mdss: mdss at ae00000 {
> + compatible = "qcom,sc7180-mdss";
> + reg = <0 0xae00000 0 0x1000>;
> + reg-names = "mdss";
> + power-domains = <&dispcc MDSS_GDSC>;
> +
> + clocks = <&gcc GCC_DISP_AHB_CLK>,
> + <&dispcc DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc DISP_CC_MDSS_MDP_CLK>;
> +
> + clock-names = "iface", "ahb", "core";
> +
> + assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>;
> + assigned-clock-rates = <300000000>;
> +
> + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> +
> + interconnects = <&mmss_noc MASTER_MDP0 &mc_virt SLAVE_EBI1>;
> +
> + interconnect-names = "mdp0-mem";
> +
> + iommus = <&apps_smmu 0x800 0x2>;
> +
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + mdp: mdp at ae01000 {
> + compatible = "qcom,sc7180-dpu";
> + reg = <0 0x0ae01000 0 0x8f000>,
> + <0 0x0aeb0000 0 0x2008>;
> +
> + reg-names = "mdp", "vbif";
> +
> + clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
> + <&dispcc DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc DISP_CC_MDSS_ROT_CLK>,
> + <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
> + <&dispcc DISP_CC_MDSS_MDP_CLK>,
> + <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
> + clock-names = "bus", "iface", "rot", "lut", "core",
> + "vsync";
> + assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>,
> + <&dispcc DISP_CC_MDSS_VSYNC_CLK>,
> + <&dispcc DISP_CC_MDSS_ROT_CLK>,
> + <&dispcc DISP_CC_MDSS_ROT_CLK>;
> + assigned-clock-rates = <300000000>,
> + <19200000>,
> + <19200000>,
> + <19200000>;
> +
> + interrupt-parent = <&mdss>;
> + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port at 0 {
> + reg = <0>;
> + dpu_intf1_out: endpoint {
> + remote-endpoint = <&dsi0_in>;
> + };
> + };
> + };
> + };
> + };
> + };
> +...
> diff --git a/Documentation/devicetree/bindings/display/msm/dpu-sdm845.yaml b/Documentation/devicetree/bindings/display/msm/dpu-sdm845.yaml
> new file mode 100644
> index 0000000..17395f6
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/msm/dpu-sdm845.yaml
> @@ -0,0 +1,216 @@
> +# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/msm/dpu-sdm845.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Description of Qualcomm Display DPU dt properties.
> +
> +maintainers:
> + - Krishna Manikandan <mkrishn at codeaurora.org>
> +
> +description: |
> + Device tree bindings for MSM Mobile Display Subsytem(MDSS) that encapsulates
> + sub-blocks like DPU display controller, DSI and DP interfaces etc. Device tree
> + bindings of MDSS and DPU are mentioned for SDM845 target.
> +
> +properties:
> + compatible:
> + items:
> + - const: qcom,sdm845-mdss
> + reg:
> + maxItems: 1
> +
> + reg-names:
> + const: mdss
> +
> + power-domains:
> + maxItems: 1
> +
> + clocks:
> + maxItems: 3
> +
> + clock-names:
> + description: |
> + Device clock names in the same order as mentioned in clocks property.
> + The required clocks are mentioned below.
> + items:
> + - const: iface
> + - const: bus
> + - const: core
> +
> + interrupts:
> + maxItems: 1
> +
> + interrupt-controller: true
> +
> + "#interrupt-cells":
> + const: 1
> +
> + iommus:
> + maxItems: 2
> +
> + "#address-cells":
> + const: 2
> +
> + "#size-cells":
> + const: 2
> +
> + ranges: true
> +
> + assigned-clocks:
> + maxItems: 1
> +
> + assigned-clock-rates:
> + maxItems: 1
> +
> +patternProperties:
> + "^mdp@[0-9a-f]+$":
> + type: object
> + description: Node containing the properties of DPU.
> +
> + properties:
> + compatible:
> + items:
> + - const: qcom,sdm845-dpu
> + reg:
> + maxItems: 2
> +
> + reg-names:
> + items:
> + - const: mdp
> + - const: vbif
> +
> + clocks:
> + maxItems: 4
> +
> + clock-names:
> + description: |
> + Device clock names, must be in same order as clocks property.
> + The following clocks are required.
> + items:
> + - const: iface
> + - const: bus
> + - const: core
> + - const: vsync
> +
> + interrupts:
> + maxItems: 1
> +
> + ports:
> + type: object
> + description: |
> + Contains the list of output ports from DPU device. These ports
> + connect to interfaces that are external to the DPU hardware,
> + such as DSI, DP etc. Each output port contains an endpoint that
> + describes how it is connected to an external interface. These
> + are described by the standard properties documented in files
> + mentioned below.
> +
> + Documentation/devicetree/bindings/graph.txt
> + Documentation/devicetree/bindings/media/video-interfaces.txt
> +
> + properties:
> + port at 0:
> + type: object
> + description: DPU_INTF1 (DSI1)
> + port at 1:
> + type: object
> + description: DPU_INTF2 (DSI2)
> +
> + assigned-clocks:
> + maxItems: 2
> +
> + assigned-clock-rates:
> + maxItems: 2
> +
> +
> +required:
> + - compatible
> + - reg
> + - reg-names
> + - power-domains
> + - clocks
> + - clock-names
> + - interrupts
> + - interrupt-controller
> + - iommus
> +
> +additionalProperties: false
> +
> +examples:
> +- |
> + #include <dt-bindings/clock/qcom,dispcc-sdm845.h>
> + #include <dt-bindings/clock/qcom,gcc-sdm845.h>
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> + soc: soc {
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + mdss: mdss at ae00000 {
> + compatible = "qcom,sdm845-mdss";
> + reg = <0 0x0ae00000 0 0x1000>;
> + reg-names = "mdss";
> + power-domains = <&dispcc MDSS_GDSC>;
> +
> + clocks = <&gcc GCC_DISP_AHB_CLK>,
> + <&gcc GCC_DISP_AXI_CLK>,
> + <&dispcc DISP_CC_MDSS_MDP_CLK>;
> + clock-names = "iface", "bus", "core";
> +
> + assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>;
> + assigned-clock-rates = <300000000>;
> +
> + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> +
> + iommus = <&apps_smmu 0x880 0x8>,
> + <&apps_smmu 0xc80 0x8>;
> +
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + mdss_mdp: mdp at ae01000 {
> + compatible = "qcom,sdm845-dpu";
> + reg = <0 0x0ae01000 0 0x8f000>,
> + <0 0x0aeb0000 0 0x2008>;
> + reg-names = "mdp", "vbif";
> +
> + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc DISP_CC_MDSS_AXI_CLK>,
> + <&dispcc DISP_CC_MDSS_MDP_CLK>,
> + <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
> + clock-names = "iface", "bus", "core", "vsync";
> +
> + assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>,
> + <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
> + assigned-clock-rates = <300000000>,
> + <19200000>;
> +
> + interrupt-parent = <&mdss>;
> + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port at 0 {
> + reg = <0>;
> + dpu_intf1_out: endpoint {
> + remote-endpoint = <&dsi0_in>;
> + };
> + };
> +
> + port at 1 {
> + reg = <1>;
> + dpu_intf2_out: endpoint {
> + remote-endpoint = <&dsi1_in>;
> + };
> + };
> + };
> + };
> + };
> + };
> +...
> +++ b/Documentation/devicetree/bindings/display/msm/dsi-common-controller.yaml
> @@ -0,0 +1,180 @@
> +# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/msm/dsi-common-controller.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Description of Qualcomm Display DSI controller dt properties.
> +
> +maintainers:
> + - Krishna Manikandan <mkrishn at codeaurora.org>
> +
> +description: |
> + Common Device tree bindings for DSI controller.
> +
> +allOf:
> + - $ref: "../dsi-controller.yaml#"
> +
> +properties:
> + compatible:
> + items:
> + - const: qcom,mdss-dsi-ctrl
> +
> + clocks:
> + maxItems: 6
> +
> + clock-names:
> + description: |
> + Device clock names in the same order as mentioned in clocks property.
> +
> + assigned-clocks:
> + description: Parents of "byte" and "pixel" for the given platform.
> +
> + assigned-clock-parents:
> + description: |
> + The Byte clock and Pixel clock PLL outputs provided by a DSI PHY block.
> + Details on clock bindings are mentioned in
> + Documentation/devicetree/bindings/clock/clock-bindings.txt.
> +
> + vdd-supply:
> + description: Phandle to vdd regulator device node.
> +
> + vddio-supply:
> + description: Phandle to vdd-io regulator device node.
> +
> + vdda-supply:
> + description: Phandle to vdda regulator device node.
> +
> + phys:
> + description: Phandle to DSI PHY device node.
> + maxItems: 1
> +
> + phy-names:
> + description: Name of the corresponding PHY device.
> + maxItems: 1
> +
> + syscon-sfpb:
> + description: A phandle to mmss_sfpb syscon node (only for DSIv2).
> + $ref: "/schemas/types.yaml#/definitions/phandle"
> +
> + # Optional Properties for dsi controller
> + qcom,mdss-mdp-transfer-time-us:
> + description: |
> + Specifies the DSI transfer time for command mode
> + panels in microseconds. Driver uses this number to adjust
> + the clock rate according to the expected transfer time.
> + Increasing this value would slow down the mdp processing
> + and can result in slower performance.
> + Decreasing this value can speed up the mdp processing,
> + but this can also impact power consumption.
> + As a rule this time should not be higher than the time
> + that would be expected with the processing at the
> + DSI link rate since anyways this would be the maximum
> + transfer time that could be achieved.
> + If ping pong split is enabled, this time should not be higher
> + than two times the DSI link rate time.
> + If the property is not specified, then the default value is
> + 14000 us. This is an optional property.
'default: 14000' is how to describe defaults as a schema.
Is there not a range you can define less than 0 - 2^32?
> +
> + qcom,dual-dsi-mode:
> + type: boolean
> + description: |
> + Boolean value indicating if the DSI controller is
> + driving a panel which needs 2 DSI links.
> +
> + qcom,master-dsi:
> + type: boolean
> + description: |
> + Boolean value indicating if the DSI controller is driving
> + the master link of the 2-DSI panel.
> +
> + qcom,sync-dual-dsi:
> + type: boolean
> + description: |
> + Boolean value indicating if the DSI controller is driving a
> + 2-DSI panel whose 2 links need receive command simultaneously.
> +
> + pinctrl-names:
> + description: The pin control state names.
> + items:
> + - const: default
> + - const: sleep
> +
> + pinctrl-0:
> + description: The default pinctrl state (active)
> +
> + pinctrl-1:
> + description: The sleep pinctrl state (suspend)
> +
> + ports:
> + type: object
> + description: |
> + Contains DSI controller input and output ports as children, each
> + containing one endpoint subnode as defined in
> + Documentation/devicetree/bindings/graph.txt and
> + Documentation/devicetree/bindings/media/video-interfaces.txt.
> +
> + properties:
> + port at 0:
> + type: object
> + description: |
> + Input endpoints of the controller.
> +
> + properties:
> + reg:
> + const: 0
> +
> + endpoint:
> + type: object
> + properties:
> + remote-endpoint:
> + description: |
> + For port at 0, set to phandle of the connected panel/bridge's
> + input endpoint. For port at 1, set to the MDP interface output.
> + See Documentation/devicetree/bindings/graph.txt for
> + device graph info.
> +
> + data-lanes:
> + description: |
> + This describes how the physical DSI data lanes are mapped
> + to the logical lanes on the given platform. The value contained in
> + index n describes what physical lane is mapped to the logical lane n
> + (DATAn, where n lies between 0 and 3). The clock lane position is fixed
> + and can't be changed. Hence, they aren't a part of the DT bindings. See
> + Documentation/devicetree/bindings/media/video-interfaces.txt for
> + more info on the data-lanes property.
> +
> + For example:
> + data-lanes = <3 0 1 2>;
> +
> + The above mapping describes that the logical data lane DATA0 is mapped
> + to the physical data lane DATA3, logical DATA1 to physical DATA0,
> + logic DATA2 to phys DATA1 and logic DATA3 to phys DATA2. There are
> + only a limited number of physical to logical mappings possible.
> + oneOf:
> + - const: <0 1 2 3>
> + - const: <1 2 3 0>
> + - const: <2 3 0 1>
> + - const: <3 0 1 2>
> + - const: <0 3 2 1>
> + - const: <1 0 3 2>
> + - const: <2 1 0 3>
> + - const: <3 2 1 0>
Looks kind of like a schema, but is not... It's just part of
'description' because of the indent. There's not really a concise way to
enumeration array values, you have to do something like this:
oneOf:
- items:
- const: 0
- const: 1
- const: 2
- const: 3
- items:
- const: 1
- const: 2
- const: 3
- const: 0
...
> + maxItems: 1
> +
> + port at 1:
> + type: object
> + description: |
> + Output endpoints of the controller.
> + properties:
> + reg:
> + const: 1
> +
> + endpoint:
> + type: object
> + properties:
> + remote-endpoint: true
> + data-lanes:
> + maxItems: 1
This is saying 'data-lanes' is a single scalar value. If so, then what
are the possible values?
> +
> +...
> diff --git a/Documentation/devicetree/bindings/display/msm/dsi-controller-sc7180.yaml b/Documentation/devicetree/bindings/display/msm/dsi-controller-sc7180.yaml
> new file mode 100644
> index 0000000..6f3e179
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/msm/dsi-controller-sc7180.yaml
> @@ -0,0 +1,120 @@
> +# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/msm/dsi-controller-sc7180.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Description of Qualcomm Display DSI controller dt properties.
> +
> +maintainers:
> + - Krishna Manikandan <mkrishn at codeaurora.org>
> +
> +description: |
> + Device tree bindings for DSI controller for SC7180 target.
> +
> +allOf:
> + - $ref: dsi-common-controller.yaml#
> +
> +properties:
> + compatible:
> + const: qcom,mdss-dsi-ctrl
> +
> + reg:
> + maxItems: 1
> +
> + reg-names:
> + const: dsi_ctrl
> +
> + interrupts:
> + maxItems: 1
> +
> + clocks:
> + maxItems: 6
> +
> + clock-names:
> + items:
> + - const: byte
> + - const: byte_intf
> + - const: pixel
> + - const: core
> + - const: iface
> + - const: bus
> +
> + phys:
> + maxItems: 1
> +
> + phy-names:
> + const: dsi
> +
> + ports: true
> +
> +required:
> + - compatible
> + - reg
> + - reg-names
> + - interrupts
> + - clocks
> + - clock-names
> + - phys
> + - phy-names
> + - ports
> +
> +unevaluatedProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + #include <dt-bindings/clock/qcom,dispcc-sc7180.h>
> + #include <dt-bindings/clock/qcom,gcc-sc7180.h>
> +
> + mdss: mdss {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> +
> + dsi0: dsi at ae94000 {
> + compatible = "qcom,mdss-dsi-ctrl";
> + reg = <0 0x0ae94000 0 0x400>;
> + reg-names = "dsi_ctrl";
> +
> + interrupt-parent = <&mdss>;
> + interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
> +
> + clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
> + <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
> + <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
> + <&dispcc DISP_CC_MDSS_ESC0_CLK>,
> + <&dispcc DISP_CC_MDSS_AHB_CLK>,
> + <&gcc GCC_DISP_HF_AXI_CLK>;
> +
> + clock-names = "byte",
> + "byte_intf",
> + "pixel",
> + "core",
> + "iface",
> + "bus";
> +
> + phys = <&dsi_phy>;
> + phy-names = "dsi";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + port at 0 {
> + reg = <0>;
> + dsi0_in: endpoint {
> + remote-endpoint = <&dpu_intf1_out>;
> + };
> + };
> +
> + port at 1 {
> + reg = <1>;
> + dsi0_out: endpoint {
> + };
> + };
> + };
> + };
> + };
> +...
> +
> diff --git a/Documentation/devicetree/bindings/display/msm/dsi-controller-sdm845.yaml b/Documentation/devicetree/bindings/display/msm/dsi-controller-sdm845.yaml
> new file mode 100644
> index 0000000..5dae89e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/msm/dsi-controller-sdm845.yaml
> @@ -0,0 +1,120 @@
> +# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/msm/dsi-controller-sdm845.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Description of Qualcomm Display DSI controller dt properties.
> +
> +maintainers:
> + - Krishna Manikandan <mkrishn at codeaurora.org>
> +
> +description: |
> + Device tree bindings for DSI controller for SDM845 target.
> +
> +allOf:
> + - $ref: dsi-common-controller.yaml#
> +
> +properties:
> + compatible:
> + const: qcom,mdss-dsi-ctrl
Same compatible twice?
IIRC, there were some differences in the various DSI controllers, but
now they look identical to me?
> +
> + reg:
> + maxItems: 1
> +
> + reg-names:
> + const: dsi_ctrl
> +
> + interrupts:
> + maxItems: 1
> +
> + clocks:
> + maxItems: 6
> +
> + clock-names:
> + items:
> + - const: byte
> + - const: byte_intf
> + - const: pixel
> + - const: core
> + - const: iface
> + - const: bus
> +
> + phys:
> + maxItems: 1
> +
> + phy-names:
> + const: dsi
> +
> + ports: true
> +
> +required:
> + - compatible
> + - reg
> + - reg-names
> + - interrupts
> + - clocks
> + - clock-names
> + - phys
> + - phy-names
> + - ports
> +
> +unevaluatedProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + #include <dt-bindings/clock/qcom,dispcc-sdm845.h>
> + #include <dt-bindings/clock/qcom,gcc-sdm845.h>
> +
> + mdss: mdss {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> +
> + dsi0: dsi at ae94000 {
> + compatible = "qcom,mdss-dsi-ctrl";
> + reg = <0 0x0ae94000 0 0x400>;
> + reg-names = "dsi_ctrl";
> +
> + interrupt-parent = <&mdss>;
> + interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
> +
> + clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
> + <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
> + <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
> + <&dispcc DISP_CC_MDSS_ESC0_CLK>,
> + <&dispcc DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc DISP_CC_MDSS_AXI_CLK>;
> + clock-names = "byte",
> + "byte_intf",
> + "pixel",
> + "core",
> + "iface",
> + "bus";
> +
> + phys = <&dsi0_phy>;
> + phy-names = "dsi";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port at 0 {
> + reg = <0>;
> + dsi0_in: endpoint {
> + remote-endpoint = <&dpu_intf1_out>;
> + };
> + };
> +
> + port at 1 {
> + reg = <1>;
> + dsi0_out: endpoint {
> + };
> + };
> + };
> + };
> + };
> +...
> +
> diff --git a/Documentation/devicetree/bindings/display/msm/dsi-phy-sc7180.yaml b/Documentation/devicetree/bindings/display/msm/dsi-phy-sc7180.yaml
> new file mode 100644
> index 0000000..039c50f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/msm/dsi-phy-sc7180.yaml
> @@ -0,0 +1,80 @@
> +# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/msm/dsi-phy-sc7180.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Description of Qualcomm Display DSI PHY dt properties.
> +
> +maintainers:
> + - Krishna Manikandan <mkrishn at codeaurora.org>
> +
> +description: |
> + Device tree bindings for DSI PHY for SC7180 target.
> +
> +allOf:
> + - $ref: dsi-phy.yaml#
> +
> +properties:
> + compatible:
> + const: qcom,dsi-phy-10nm
> +
> + reg:
> + maxItems: 3
> +
> + reg-names:
> + maxItems: 3
> +
> + clocks:
> + maxItems: 2
> +
> + clock-names:
> + items:
> + - const: iface
> + - const: ref
> +
> + "#clock-cells":
> + const: 1
> +
> + "#phy-cells":
> + const: 0
> +
> +required:
> + - compatible
> + - reg
> + - reg-names
> + - clocks
> + - clock-names
> +
> +unevaluatedProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + #include <dt-bindings/clock/qcom,dispcc-sc7180.h>
> + #include <dt-bindings/clock/qcom,gcc-sc7180.h>
> + #include <dt-bindings/clock/qcom,rpmh.h>
> +
> + mdss: mdss {
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + dsi_phy: dsi-phy at ae94400 {
> + compatible = "qcom,dsi-phy-10nm";
> + reg = <0 0x0ae94400 0 0x200>,
> + <0 0x0ae94600 0 0x280>,
> + <0 0x0ae94a00 0 0x1e0>;
> + reg-names = "dsi_phy",
> + "dsi_phy_lane",
> + "dsi_pll";
> +
> + vdds-supply = <&vdda_mipi_dsi0_pll>;
> + #clock-cells = <1>;
> + #phy-cells = <0>;
> + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> + <&rpmhcc RPMH_CXO_CLK>;
> + clock-names = "iface", "ref";
> + };
> + };
> +...
> +
> diff --git a/Documentation/devicetree/bindings/display/msm/dsi-phy-sdm845.yaml b/Documentation/devicetree/bindings/display/msm/dsi-phy-sdm845.yaml
> new file mode 100644
> index 0000000..4abae0e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/msm/dsi-phy-sdm845.yaml
> @@ -0,0 +1,82 @@
> +# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/msm/dsi-phy-sdm845.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Description of Qualcomm Display DSI PHY dt properties.
> +
> +maintainers:
> + - Krishna Manikandan <mkrishn at codeaurora.org>
> +
> +description: |
> + Device tree bindings for DSI PHY for SDM845 target.
> +
> +allOf:
> + - $ref: dsi-phy.yaml#
> +
> +properties:
> + compatible:
> + const: qcom,dsi-phy-10nm
> +
> + reg:
> + maxItems: 3
> +
> + reg-names:
> + maxItems: 3
> +
> + clocks:
> + maxItems: 2
> +
> + clock-names:
> + items:
> + - const: iface
> + - const: ref
> +
> + "#clock-cells":
> + const: 1
> +
> + "#phy-cells":
> + const: 0
> +
> +required:
> + - compatible
> + - reg
> + - reg-names
> + - clocks
> + - clock-names
> +
> +unevaluatedProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + #include <dt-bindings/clock/qcom,dispcc-sdm845.h>
> + #include <dt-bindings/clock/qcom,gcc-sdm845.h>
> + #include <dt-bindings/clock/qcom,rpmh.h>
> +
> + mdss: mdss {
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + dsi0_phy: dsi-phy at ae94400 {
> + compatible = "qcom,dsi-phy-10nm";
> + reg = <0 0x0ae94400 0 0x200>,
> + <0 0x0ae94600 0 0x280>,
> + <0 0x0ae94a00 0 0x1e0>;
> + reg-names = "dsi_phy",
> + "dsi_phy_lane",
> + "dsi_pll";
> +
> + #clock-cells = <1>;
> + #phy-cells = <0>;
> +
> + vdds-supply = <&vdda_mipi_dsi0_pll>;
> + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> + <&rpmhcc RPMH_CXO_CLK>;
> + clock-names = "iface", "ref";
> +
> + };
> + };
> +...
> +
> diff --git a/Documentation/devicetree/bindings/display/msm/dsi-phy.yaml b/Documentation/devicetree/bindings/display/msm/dsi-phy.yaml
> new file mode 100644
> index 0000000..ee58e58
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/msm/dsi-phy.yaml
> @@ -0,0 +1,126 @@
> +# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/msm/dsi-phy.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Description of Qualcomm Display DSI PHY dt properties.
> +
> +maintainers:
> + - Krishna Manikandan <mkrishn at codeaurora.org>
> +
> +description: |
> + Common Device tree bindings for DSI PHY.
> +
> +properties:
> + compatible:
> + oneOf:
> + - const: qcom,dsi-phy-28nm-hpm
> + - const: qcom,dsi-phy-28nm-lp
> + - const: qcom,dsi-phy-20nm
> + - const: qcom,dsi-phy-28nm-8960
> + - const: qcom,dsi-phy-14nm
> + - const: qcom,dsi-phy-10nm
> + - const: qcom,dsi-phy-10nm-8998
> +
> + reg-names:
> + description: Name of register regions.
> +
> + clock-cells:
> + description: |
> + The DSI PHY block acts as a clock provider, creating
> + 2 clocks: A byte clock (index 0), and a pixel clock (index 1).
> + const: 1
> +
> + power-domains:
> + maxItems: 1
> +
> + clocks:
> + maxItems: 2
> +
> + clock-names:
> + description: |
> + The following clocks are required.
> + items:
> + - const: iface
> + - const: ref
> +
> + qcom,dsi-phy-regulator-ldo-mode:
> + type: boolean
> + description: |
> + Boolean value indicating if the LDO mode PHY regulator is wanted (optional).
> +
> +required:
> + - compatible
> + - reg
> + - reg-names
> + - clocks
> + - clock-names
> +
> +
> +allOf:
> + - if:
The point of creating a common schema or splitting the schemas into
separate files was to reduce the number of if/then schemas. This doesn't
seem to have done any of that.
> + properties:
> + compatible:
> + contains:
> + enum:
> + - qcom,dsi-phy-28nm-hpm
> + - qcom,dsi-phy-28nm-lp
> + - qcom,dsi-phy-20nm
> + - qcom,dsi-phy-28nm-8960
> + then:
> + required:
> + - vddio-supply
> +
> + - if:
> + properties:
> + compatible:
> + contains:
> + enum:
> + - qcom,dsi-phy-20nm
> + - qcom,dsi-phy-14nm
> + then:
> + required:
> + - vcca-supply
> +
> + - if:
> + properties:
> + compatible:
> + contains:
> + enum:
> + - qcom,dsi-phy-10nm
> + then:
> + required:
> + - vdds-supply
Why do you need this if/then here? You've got a schema file dedicated to
qcom,dsi-phy-10nm.
> +
> + - if:
> + properties:
> + compatible:
> + contains:
> + enum:
> + - qcom,dsi-phy-28nm-hpm
> + - qcom,dsi-phy-28nm-lp
> + - qcom,dsi-phy-28nm-8960
> + - qcom,dsi-phy-20nm
You already have this condition above, you don't need to repeat it here.
Or maybe these 4 compatibles should be in their own schema file.
> + then:
> + properties:
> + reg-names:
> + items:
> + - const: dsi_pll
> + - const: dsi_phy
> + - const: dsi_phy_regulator
> + - if:
> + properties:
> + compatible:
> + contains:
> + enum:
> + - qcom,dsi-phy-14nm
> + - qcom,dsi-phy-10nm
> + then:
> + properties:
> + reg-names:
> + items:
> + - const: dsi_phy
> + - const: dsi_phy_lane
> + - const: dsi_pll
> +...
More information about the dri-devel
mailing list