[RFC][PATCH] regulator: rpi-panel: Add regulator/backlight driver for RPi panel
Sam Ravnborg
sam at ravnborg.org
Thu Jul 30 15:59:44 UTC 2020
Hi Marek
On Wed, Jul 29, 2020 at 11:46:45PM +0200, Marek Vasut wrote:
> This regulator/backlight driver handles the ATTINY88 present on the
> RPi 7" touchscreen panel and exposes the power/backlight interfaces.
>
> Signed-off-by: Marek Vasut <marex at denx.de>
> To: dri-devel at lists.freedesktop.org
> Cc: Eric Anholt <eric at anholt.net>
> Cc: Mark Brown <broonie at kernel.org>
> Cc: Sam Ravnborg <sam at ravnborg.org>
It looks strange that the regulator and the backligth are defined in the
same module like this.
The usual approach is to have an independent regulator and an
independent backlight. Each are represented by their own node in the DT.
Also the compatible "raspberrypi,7inch-touchscreen-panel-regulator",
is unknown. We need a binding for the compatible.
For backlight drivers, and modules that includes backlight support it
would be good to include the backlight gang in cc:
Jingoo, Lee, Daniel.
One detail below - but I otherwise did not look at the code.
Sam
> ---
> drivers/regulator/Kconfig | 10 +
> drivers/regulator/Makefile | 1 +
> .../regulator/rpi-panel-attiny-regulator.c | 214 ++++++++++++++++++
> 3 files changed, 225 insertions(+)
> create mode 100644 drivers/regulator/rpi-panel-attiny-regulator.c
>
> diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
> index de17ef7e18f0..439cc5226bae 100644
> --- a/drivers/regulator/Kconfig
> +++ b/drivers/regulator/Kconfig
> @@ -864,6 +864,16 @@ config REGULATOR_QCOM_USB_VBUS
> Say M here if you want to include support for enabling the VBUS output
> as a module. The module will be named "qcom_usb_vbus_regulator".
>
> +config REGULATOR_RASPBERRYPI_TOUCHSCREEN_ATTINY
> + tristate "Raspberry Pi 7-inch touchscreen panel ATTINY regulator"
> + depends on BACKLIGHT_CLASS_DEVICE
> + depends on I2C
> + select REGMAP_I2C
> + help
> + This driver supports ATTINY regulator on the Raspberry Pi 7-inch
> + touchscreen unit. The regulator is used to enable power to the
> + TC358762, display and to control backlight.
> +
> config REGULATOR_RC5T583
> tristate "RICOH RC5T583 Power regulators"
> depends on MFD_RC5T583
> diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
> index d8d3ecf526a8..6e39ea87901e 100644
> --- a/drivers/regulator/Makefile
> +++ b/drivers/regulator/Makefile
> @@ -107,6 +107,7 @@ obj-$(CONFIG_REGULATOR_TPS51632) += tps51632-regulator.o
> obj-$(CONFIG_REGULATOR_PBIAS) += pbias-regulator.o
> obj-$(CONFIG_REGULATOR_PCAP) += pcap-regulator.o
> obj-$(CONFIG_REGULATOR_PCF50633) += pcf50633-regulator.o
> +obj-$(CONFIG_REGULATOR_RASPBERRYPI_TOUCHSCREEN_ATTINY) += rpi-panel-attiny-regulator.o
> obj-$(CONFIG_REGULATOR_RC5T583) += rc5t583-regulator.o
> obj-$(CONFIG_REGULATOR_RK808) += rk808-regulator.o
> obj-$(CONFIG_REGULATOR_RN5T618) += rn5t618-regulator.o
> diff --git a/drivers/regulator/rpi-panel-attiny-regulator.c b/drivers/regulator/rpi-panel-attiny-regulator.c
> new file mode 100644
> index 000000000000..ee46bfbf5eee
> --- /dev/null
> +++ b/drivers/regulator/rpi-panel-attiny-regulator.c
> @@ -0,0 +1,214 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2020 Marek Vasut <marex at denx.de>
> + *
> + * Based on rpi_touchscreen.c by Eric Anholt <eric at anholt.net>
> + */
> +
> +#include <linux/backlight.h>
> +#include <linux/err.h>
> +#include <linux/gpio.h>
> +#include <linux/i2c.h>
> +#include <linux/init.h>
> +#include <linux/interrupt.h>
> +#include <linux/module.h>
> +#include <linux/regmap.h>
> +#include <linux/regulator/driver.h>
> +#include <linux/regulator/machine.h>
> +#include <linux/regulator/of_regulator.h>
> +#include <linux/slab.h>
> +
> +/* I2C registers of the Atmel microcontroller. */
> +#define REG_ID 0x80
> +#define REG_PORTA 0x81
> +#define REG_PORTA_HF BIT(2)
> +#define REG_PORTA_VF BIT(3)
> +#define REG_PORTB 0x82
> +#define REG_POWERON 0x85
> +#define REG_PWM 0x86
> +
> +static const struct regmap_config attiny_regmap_config = {
> + .reg_bits = 8,
> + .val_bits = 8,
> + .max_register = REG_PWM,
> + .cache_type = REGCACHE_NONE,
> +};
> +
> +static int attiny_lcd_power_enable(struct regulator_dev *rdev)
> +{
> + unsigned int data;
> +
> + regmap_write(rdev->regmap, REG_POWERON, 1);
> + /* Wait for nPWRDWN to go low to indicate poweron is done. */
> + regmap_read_poll_timeout(rdev->regmap, REG_PORTB, data,
> + data & BIT(0), 10, 1000000);
> +
> + /* Default to the same orientation as the closed source
> + * firmware used for the panel. Runtime rotation
> + * configuration will be supported using VC4's plane
> + * orientation bits.
> + */
> + regmap_write(rdev->regmap, REG_PORTA, BIT(2));
> +
> + return 0;
> +}
> +
> +static int attiny_lcd_power_disable(struct regulator_dev *rdev)
> +{
> + regmap_write(rdev->regmap, REG_PWM, 0);
> + regmap_write(rdev->regmap, REG_POWERON, 0);
> + udelay(1);
> + return 0;
> +}
> +
> +static int attiny_lcd_power_is_enabled(struct regulator_dev *rdev)
> +{
> + unsigned int data;
> + int ret;
> +
> + ret = regmap_read(rdev->regmap, REG_POWERON, &data);
> + if (ret < 0)
> + return ret;
> +
> + if (!(data & BIT(0)))
> + return 0;
> +
> + ret = regmap_read(rdev->regmap, REG_PORTB, &data);
> + if (ret < 0)
> + return ret;
> +
> + return data & BIT(0);
> +}
> +
> +static const struct regulator_init_data attiny_regulator_default = {
> + .constraints = {
> + .valid_ops_mask = REGULATOR_CHANGE_STATUS,
> + },
> +};
> +
> +static const struct regulator_ops attiny_regulator_ops = {
> + .enable = attiny_lcd_power_enable,
> + .disable = attiny_lcd_power_disable,
> + .is_enabled = attiny_lcd_power_is_enabled,
> +};
> +
> +static const struct regulator_desc attiny_regulator = {
> + .name = "tc358762-power",
> + .ops = &attiny_regulator_ops,
> + .type = REGULATOR_VOLTAGE,
> + .owner = THIS_MODULE,
> +};
> +
> +static int attiny_update_status(struct backlight_device *bl)
> +{
> + struct regmap *regmap = bl_get_data(bl);
> + int brightness = bl->props.brightness;
> +
> + if (bl->props.power != FB_BLANK_UNBLANK ||
> + bl->props.fb_blank != FB_BLANK_UNBLANK)
> + brightness = 0;
> +
We have recently introduced backlight_get_brightness().
Using this function will make this implemenation much simpler.
But it is only availabe in the backlight tree for now.
Sam
> + return regmap_write(regmap, REG_PWM, brightness);
> +}
> +
> +static int attiny_get_brightness(struct backlight_device *bl)
> +{
> + struct regmap *regmap = bl_get_data(bl);
> + int ret, brightness;
> +
> + ret = regmap_read(regmap, REG_PWM, &brightness);
> + if (ret)
> + return ret;
> +
> + return brightness;
> +}
> +
> +static const struct backlight_ops attiny_bl = {
> + .update_status = attiny_update_status,
> + .get_brightness = attiny_get_brightness,
> +};
> +
> +/*
> + * I2C driver interface functions
> + */
> +static int attiny_i2c_probe(struct i2c_client *i2c,
> + const struct i2c_device_id *id)
> +{
> + struct backlight_properties props = { };
> + struct regulator_config config = { };
> + struct backlight_device *bl;
> + struct regulator_dev *rdev;
> + struct regmap *regmap;
> + unsigned int data;
> + int ret;
> +
> + regmap = devm_regmap_init_i2c(i2c, &attiny_regmap_config);
> + if (IS_ERR(regmap)) {
> + ret = PTR_ERR(regmap);
> + dev_err(&i2c->dev, "Failed to allocate register map: %d\n",
> + ret);
> + return ret;
> + }
> +
> + ret = regmap_read(regmap, REG_ID, &data);
> + if (ret < 0) {
> + dev_err(&i2c->dev, "Failed to read REG_ID reg: %d\n", ret);
> + return ret;
> + }
> +
> + switch (data) {
> + case 0xde: /* ver 1 */
> + case 0xc3: /* ver 2 */
> + break;
> + default:
> + dev_err(&i2c->dev, "Unknown Atmel firmware revision: 0x%02x\n", data);
> + return -ENODEV;
> + }
> +
> + regmap_write(regmap, REG_POWERON, 0);
> + mdelay(1);
> +
> + config.dev = &i2c->dev;
> + config.regmap = regmap;
> + config.of_node = i2c->dev.of_node;
> + config.init_data = &attiny_regulator_default;
> +
> + rdev = devm_regulator_register(&i2c->dev, &attiny_regulator, &config);
> + if (IS_ERR(rdev)) {
> + dev_err(&i2c->dev, "Failed to register ATTINY regulator\n");
> + return PTR_ERR(rdev);
> + }
> +
> + props.type = BACKLIGHT_RAW;
> + props.max_brightness = 0xff;
> + bl = devm_backlight_device_register(&i2c->dev,
> + "7inch-touchscreen-panel-bl",
> + &i2c->dev, regmap, &attiny_bl,
> + &props);
> + if (IS_ERR(bl))
> + return PTR_ERR(bl);
> +
> + bl->props.brightness = 0xff;
> +
> + return 0;
> +}
> +
> +static const struct of_device_id attiny_dt_ids[] = {
> + { .compatible = "raspberrypi,7inch-touchscreen-panel-regulator" },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, attiny_dt_ids);
> +
> +static struct i2c_driver attiny_regulator_driver = {
> + .driver = {
> + .name = "rpi_touchscreen_attiny",
> + .of_match_table = of_match_ptr(attiny_dt_ids),
> + },
> + .probe = attiny_i2c_probe,
> +};
> +
> +module_i2c_driver(attiny_regulator_driver);
> +
> +MODULE_AUTHOR("Marek Vasut <marex at denx.de>");
> +MODULE_DESCRIPTION("Regulator device driver for Raspberry Pi 7-inch touchscreen");
> +MODULE_LICENSE("GPL v2");
> --
> 2.27.0
More information about the dri-devel
mailing list