[PATCH v4] display/drm/bridge: TC358775 DSI/LVDS driver
Neil Armstrong
narmstrong at baylibre.com
Tue Jun 30 07:27:06 UTC 2020
Hi,
On 29/06/2020 10:47, Vinay Simha B N wrote:
> Neil,
>
> yaml is the v3 version, there was no change , so i had not created v4 for yaml
> [PATCH v3 2/2] display/drm/bridge: TC358775 DSI/LVDS driver
>
OK, please resend the whole patchset even with unchanged patches, you can explain
which patches were not changed on the cover letter.
Neil
>
> On Mon, Jun 29, 2020 at 2:08 PM Neil Armstrong <narmstrong at baylibre.com> wrote:
>>
>> Hi,
>>
>> On 21/06/2020 17:38, Vinay Simha BN wrote:
>>> Signed-off-by: Vinay Simha BN <simhavcs at gmail.com>
>>>
>>> ---
>>> v1:
>>> Initial version
>>>
>>> v2:
>>> * Andrzej Hajda review comments incorporated
>>> SPDX identifier
>>> development debug removed
>>> alphabetic order headers
>>> u32 instead of unit32_t
>>> magic numbers to macros for CLRSI and mux registers
>>> ignored return value
>>>
>>> * Laurent Pinchart review comments incorporated
>>> mdelay to usleep_range
>>> bus_formats added
>>>
>>> v3:
>>> * Andrzej Hajda review comments incorporated
>>> drm_connector_status removed
>>> u32 rev removed and local variabl is used
>>> regulator enable disable with proper orders and delays
>>> as per the spec
>>> devm_drm_panel_bridge_add method used instead of panel
>>> description modified
>>> dual port implemented
>>>
>>> v4:
>>> * Sam Ravnborg review comments incorporated
>>> panel->connector_type removed
>>>
>>> * Reported-by: kernel test robot <lkp at intel.com>
>>> parse_dt to static function
>>> removed the if (endpoint), since data-lanes has to be
>>> present for dsi dts ports
>>
>> I maybe missed something, but you should also post a YAML DT bindings
>> file associated to the driver.
>>
>> Neil
>>
>>
>>> ---
>>> drivers/gpu/drm/bridge/Kconfig | 10 +
>>> drivers/gpu/drm/bridge/Makefile | 1 +
>>> drivers/gpu/drm/bridge/tc358775.c | 721 ++++++++++++++++++++++++++++++
>>> 3 files changed, 732 insertions(+)
>>> create mode 100644 drivers/gpu/drm/bridge/tc358775.c
>>>
>>> diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
>>> index 43271c21d3fc..084e9853944a 100644
>>> --- a/drivers/gpu/drm/bridge/Kconfig
>>> +++ b/drivers/gpu/drm/bridge/Kconfig
>>> @@ -181,6 +181,16 @@ config DRM_TOSHIBA_TC358768
>>> help
>>> Toshiba TC358768AXBG/TC358778XBG DSI bridge chip driver.
>>>
>>> +config DRM_TOSHIBA_TC358775
>>> + tristate "Toshiba TC358775 LVDS bridge"
>>> + depends on OF
>>> + select DRM_KMS_HELPER
>>> + select REGMAP_I2C
>>> + select DRM_PANEL
>>> + select DRM_MIPI_DSI
>>> + ---help---
>>> + Toshiba TC358775 LVDS bridge chip driver.
>>> +
>>> config DRM_TI_TFP410
>>> tristate "TI TFP410 DVI/HDMI bridge"
>>> depends on OF
>>> diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
>>> index d63d4b7e4347..23c770b3bfe4 100644
>>> --- a/drivers/gpu/drm/bridge/Makefile
>>> +++ b/drivers/gpu/drm/bridge/Makefile
>>> @@ -15,6 +15,7 @@ obj-$(CONFIG_DRM_THINE_THC63LVD1024) += thc63lvd1024.o
>>> obj-$(CONFIG_DRM_TOSHIBA_TC358764) += tc358764.o
>>> obj-$(CONFIG_DRM_TOSHIBA_TC358767) += tc358767.o
>>> obj-$(CONFIG_DRM_TOSHIBA_TC358768) += tc358768.o
>>> +obj-$(CONFIG_DRM_TOSHIBA_TC358775) += tc358775.o
>>> obj-$(CONFIG_DRM_I2C_ADV7511) += adv7511/
>>> obj-$(CONFIG_DRM_TI_SN65DSI86) += ti-sn65dsi86.o
>>> obj-$(CONFIG_DRM_TI_TFP410) += ti-tfp410.o
>>> diff --git a/drivers/gpu/drm/bridge/tc358775.c b/drivers/gpu/drm/bridge/tc358775.c
>>> new file mode 100644
>>> index 000000000000..8c9bd4e77bfd
>>> --- /dev/null
>>> +++ b/drivers/gpu/drm/bridge/tc358775.c
>>> @@ -0,0 +1,721 @@
>>> +// SPDX-License-Identifier: GPL-2.0
>>> +/*
>>> + * tc358775 DSI to LVDS bridge driver
>>> + *
>>> + * Copyright (C) 2020 SMART Wireless Computing
>>> + * Author: Vinay Simha BN <simhavcs at gmail.com>
>>> + *
>>> + */
>>> +//#define DEBUG
>>> +#include <linux/clk.h>
>>> +#include <linux/device.h>
>>> +#include <linux/gpio/consumer.h>
>>> +#include <linux/i2c.h>
>>> +#include <linux/kernel.h>
>>> +#include <linux/module.h>
>>> +#include <linux/regulator/consumer.h>
>>> +#include <linux/slab.h>
>>> +
>>> +#include <drm/drm_atomic_helper.h>
>>> +#include <drm/drm_bridge.h>
>>> +#include <drm/drm_crtc_helper.h>
>>> +#include <drm/drm_dp_helper.h>
>>> +#include <drm/drm_mipi_dsi.h>
>>> +#include <drm/drm_of.h>
>>> +#include <drm/drm_panel.h>
>>> +#include <drm/drm_probe_helper.h>
>>> +
>>> +#define FLD_MASK(start, end) (((1 << ((start) - (end) + 1)) - 1) << (end))
>>> +#define FLD_VAL(val, start, end) (((val) << (end)) & FLD_MASK(start, end))
>>> +
>>> +/* Registers */
>>> +
>>> +/* DSI D-PHY Layer Registers */
>>> +#define D0W_DPHYCONTTX 0x0004 /* Data Lane 0 DPHY Tx Control */
>>> +#define CLW_DPHYCONTRX 0x0020 /* Clock Lane DPHY Rx Control */
>>> +#define D0W_DPHYCONTRX 0x0024 /* Data Lane 0 DPHY Rx Control */
>>> +#define D1W_DPHYCONTRX 0x0028 /* Data Lane 1 DPHY Rx Control */
>>> +#define D2W_DPHYCONTRX 0x002C /* Data Lane 2 DPHY Rx Control */
>>> +#define D3W_DPHYCONTRX 0x0030 /* Data Lane 3 DPHY Rx Control */
>>> +#define COM_DPHYCONTRX 0x0038 /* DPHY Rx Common Control */
>>> +#define CLW_CNTRL 0x0040 /* Clock Lane Control */
>>> +#define D0W_CNTRL 0x0044 /* Data Lane 0 Control */
>>> +#define D1W_CNTRL 0x0048 /* Data Lane 1 Control */
>>> +#define D2W_CNTRL 0x004C /* Data Lane 2 Control */
>>> +#define D3W_CNTRL 0x0050 /* Data Lane 3 Control */
>>> +#define DFTMODE_CNTRL 0x0054 /* DFT Mode Control */
>>> +
>>> +/* DSI PPI Layer Registers */
>>> +#define PPI_STARTPPI 0x0104 /* START control bit of PPI-TX function. */
>>> +#define PPI_START_FUNCTION 1
>>> +
>>> +#define PPI_BUSYPPI 0x0108
>>> +#define PPI_LINEINITCNT 0x0110 /* Line Initialization Wait Counter */
>>> +#define PPI_LPTXTIMECNT 0x0114
>>> +#define PPI_LANEENABLE 0x0134 /* Enables each lane at the PPI layer. */
>>> +#define PPI_TX_RX_TA 0x013C /* DSI Bus Turn Around timing parameters */
>>> +
>>> +/* Analog timer function enable */
>>> +#define PPI_CLS_ATMR 0x0140 /* Delay for Clock Lane in LPRX */
>>> +#define PPI_D0S_ATMR 0x0144 /* Delay for Data Lane 0 in LPRX */
>>> +#define PPI_D1S_ATMR 0x0148 /* Delay for Data Lane 1 in LPRX */
>>> +#define PPI_D2S_ATMR 0x014C /* Delay for Data Lane 2 in LPRX */
>>> +#define PPI_D3S_ATMR 0x0150 /* Delay for Data Lane 3 in LPRX */
>>> +
>>> +#define PPI_D0S_CLRSIPOCOUNT 0x0164 /* For lane 0 */
>>> +#define PPI_D1S_CLRSIPOCOUNT 0x0168 /* For lane 1 */
>>> +#define PPI_D2S_CLRSIPOCOUNT 0x016C /* For lane 2 */
>>> +#define PPI_D3S_CLRSIPOCOUNT 0x0170 /* For lane 3 */
>>> +
>>> +#define CLS_PRE 0x0180 /* Digital Counter inside of PHY IO */
>>> +#define D0S_PRE 0x0184 /* Digital Counter inside of PHY IO */
>>> +#define D1S_PRE 0x0188 /* Digital Counter inside of PHY IO */
>>> +#define D2S_PRE 0x018C /* Digital Counter inside of PHY IO */
>>> +#define D3S_PRE 0x0190 /* Digital Counter inside of PHY IO */
>>> +#define CLS_PREP 0x01A0 /* Digital Counter inside of PHY IO */
>>> +#define D0S_PREP 0x01A4 /* Digital Counter inside of PHY IO */
>>> +#define D1S_PREP 0x01A8 /* Digital Counter inside of PHY IO */
>>> +#define D2S_PREP 0x01AC /* Digital Counter inside of PHY IO */
>>> +#define D3S_PREP 0x01B0 /* Digital Counter inside of PHY IO */
>>> +#define CLS_ZERO 0x01C0 /* Digital Counter inside of PHY IO */
>>> +#define D0S_ZERO 0x01C4 /* Digital Counter inside of PHY IO */
>>> +#define D1S_ZERO 0x01C8 /* Digital Counter inside of PHY IO */
>>> +#define D2S_ZERO 0x01CC /* Digital Counter inside of PHY IO */
>>> +#define D3S_ZERO 0x01D0 /* Digital Counter inside of PHY IO */
>>> +
>>> +#define PPI_CLRFLG 0x01E0 /* PRE Counters has reached set values */
>>> +#define PPI_CLRSIPO 0x01E4 /* Clear SIPO values, Slave mode use only. */
>>> +#define HSTIMEOUT 0x01F0 /* HS Rx Time Out Counter */
>>> +#define HSTIMEOUTENABLE 0x01F4 /* Enable HS Rx Time Out Counter */
>>> +#define DSI_STARTDSI 0x0204 /* START control bit of DSI-TX function */
>>> +#define DSI_RX_START 1
>>> +
>>> +#define DSI_BUSYDSI 0x0208
>>> +#define DSI_LANEENABLE 0x0210 /* Enables each lane at the Protocol layer. */
>>> +#define DSI_LANESTATUS0 0x0214 /* Displays lane is in HS RX mode. */
>>> +#define DSI_LANESTATUS1 0x0218 /* Displays lane is in ULPS or STOP state */
>>> +
>>> +#define DSI_INTSTATUS 0x0220 /* Interrupt Status */
>>> +#define DSI_INTMASK 0x0224 /* Interrupt Mask */
>>> +#define DSI_INTCLR 0x0228 /* Interrupt Clear */
>>> +#define DSI_LPTXTO 0x0230 /* Low Power Tx Time Out Counter */
>>> +
>>> +#define DSIERRCNT 0x0300 /* DSI Error Count */
>>> +#define APLCTRL 0x0400 /* Application Layer Control */
>>> +#define RDPKTLN 0x0404 /* Command Read Packet Length */
>>> +
>>> +#define VPCTRL 0x0450 /* Video Path Control */
>>> +#define HTIM1 0x0454 /* Horizontal Timing Control 1 */
>>> +#define HTIM2 0x0458 /* Horizontal Timing Control 2 */
>>> +#define VTIM1 0x045C /* Vertical Timing Control 1 */
>>> +#define VTIM2 0x0460 /* Vertical Timing Control 2 */
>>> +#define VFUEN 0x0464 /* Video Frame Timing Update Enable */
>>> +#define VFUEN_EN BIT(0) /* Upload Enable */
>>> +
>>> +/* Mux Input Select for LVDS LINK Input */
>>> +#define LV_MX0003 0x0480 /* Bit 0 to 3 */
>>> +#define LV_MX0407 0x0484 /* Bit 4 to 7 */
>>> +#define LV_MX0811 0x0488 /* Bit 8 to 11 */
>>> +#define LV_MX1215 0x048C /* Bit 12 to 15 */
>>> +#define LV_MX1619 0x0490 /* Bit 16 to 19 */
>>> +#define LV_MX2023 0x0494 /* Bit 20 to 23 */
>>> +#define LV_MX2427 0x0498 /* Bit 24 to 27 */
>>> +#define LV_MX(b0, b1, b2, b3) (FLD_VAL(b0, 4, 0) | FLD_VAL(b1, 12, 8) | \
>>> + FLD_VAL(b2, 20, 16) | FLD_VAL(b3, 28, 24))
>>> +
>>> +/* Input bit numbers used in mux registers */
>>> +enum {
>>> + LVI_R0,
>>> + LVI_R1,
>>> + LVI_R2,
>>> + LVI_R3,
>>> + LVI_R4,
>>> + LVI_R5,
>>> + LVI_R6,
>>> + LVI_R7,
>>> + LVI_G0,
>>> + LVI_G1,
>>> + LVI_G2,
>>> + LVI_G3,
>>> + LVI_G4,
>>> + LVI_G5,
>>> + LVI_G6,
>>> + LVI_G7,
>>> + LVI_B0,
>>> + LVI_B1,
>>> + LVI_B2,
>>> + LVI_B3,
>>> + LVI_B4,
>>> + LVI_B5,
>>> + LVI_B6,
>>> + LVI_B7,
>>> + LVI_HS,
>>> + LVI_VS,
>>> + LVI_DE,
>>> + LVI_L0
>>> +};
>>> +
>>> +#define LVCFG 0x049C /* LVDS Configuration */
>>> +#define LVPHY0 0x04A0 /* LVDS PHY 0 */
>>> +#define LV_PHY0_RST(v) FLD_VAL(v, 22, 22) /* PHY reset */
>>> +#define LV_PHY0_IS(v) FLD_VAL(v, 15, 14)
>>> +#define LV_PHY0_ND(v) FLD_VAL(v, 4, 0) /* Frequency range select */
>>> +#define LV_PHY0_PRBS_ON(v) FLD_VAL(v, 20, 16) /* Clock/Data Flag pins */
>>> +
>>> +#define LVPHY1 0x04A4 /* LVDS PHY 1 */
>>> +#define SYSSTAT 0x0500 /* System Status */
>>> +#define SYSRST 0x0504 /* System Reset */
>>> +
>>> +#define SYS_RST_I2CS BIT(0) /* Reset I2C-Slave controller */
>>> +#define SYS_RST_I2CM BIT(1) /* Reset I2C-Master controller */
>>> +#define SYS_RST_LCD BIT(2) /* Reset LCD controller */
>>> +#define SYS_RST_BM BIT(3) /* Reset Bus Management controller */
>>> +#define SYS_RST_DSIRX BIT(4) /* Reset DSI-RX and App controller */
>>> +#define SYS_RST_REG BIT(5) /* Reset Register module */
>>> +
>>> +/* GPIO Registers */
>>> +#define GPIOC 0x0520 /* GPIO Control */
>>> +#define GPIOO 0x0524 /* GPIO Output */
>>> +#define GPIOI 0x0528 /* GPIO Input */
>>> +
>>> +/* I2C Registers */
>>> +#define I2CTIMCTRL 0x0540 /* I2C IF Timing and Enable Control */
>>> +#define I2CMADDR 0x0544 /* I2C Master Addressing */
>>> +#define WDATAQ 0x0548 /* Write Data Queue */
>>> +#define RDATAQ 0x054C /* Read Data Queue */
>>> +
>>> +/* Chip ID and Revision ID Register */
>>> +#define IDREG 0x0580
>>> +
>>> +#define LPX_PERIOD 4
>>> +#define TTA_GET 0x40000
>>> +#define TTA_SURE 6
>>> +
>>> +#define TC358775XBG_ID 0x00007500
>>> +
>>> +/* Debug Registers */
>>> +#define DEBUG00 0x05A0 /* Debug */
>>> +#define DEBUG01 0x05A4 /* LVDS Data */
>>> +
>>> +#define DSI_CLEN_BIT BIT(0)
>>> +#define DIVIDE_BY_3 3 /* PCLK=DCLK/3 */
>>> +#define DIVIDE_BY_6 6 /* PCLK=DCLK/6 */
>>> +#define LVCFG_LVEN_BIT BIT(0)
>>> +
>>> +#define L0EN BIT(1)
>>> +
>>> +#define TC358775_VPCTRL_VSDELAY__MASK 0x3FF00000
>>> +#define TC358775_VPCTRL_VSDELAY__SHIFT 20
>>> +static inline u32 TC358775_VPCTRL_VSDELAY(uint32_t val)
>>> +{
>>> + return ((val) << TC358775_VPCTRL_VSDELAY__SHIFT) &
>>> + TC358775_VPCTRL_VSDELAY__MASK;
>>> +}
>>> +
>>> +#define TC358775_VPCTRL_OPXLFMT__MASK 0x00000100
>>> +#define TC358775_VPCTRL_OPXLFMT__SHIFT 8
>>> +static inline u32 TC358775_VPCTRL_OPXLFMT(uint32_t val)
>>> +{
>>> + return ((val) << TC358775_VPCTRL_OPXLFMT__SHIFT) &
>>> + TC358775_VPCTRL_OPXLFMT__MASK;
>>> +}
>>> +
>>> +#define TC358775_VPCTRL_MSF__MASK 0x00000001
>>> +#define TC358775_VPCTRL_MSF__SHIFT 0
>>> +static inline u32 TC358775_VPCTRL_MSF(uint32_t val)
>>> +{
>>> + return ((val) << TC358775_VPCTRL_MSF__SHIFT) &
>>> + TC358775_VPCTRL_MSF__MASK;
>>> +}
>>> +
>>> +#define TC358775_LVCFG_PCLKDIV__MASK 0x000000f0
>>> +#define TC358775_LVCFG_PCLKDIV__SHIFT 4
>>> +static inline u32 TC358775_LVCFG_PCLKDIV(uint32_t val)
>>> +{
>>> + return ((val) << TC358775_LVCFG_PCLKDIV__SHIFT) &
>>> + TC358775_LVCFG_PCLKDIV__MASK;
>>> +}
>>> +
>>> +#define TC358775_LVCFG_LVDLINK__MASK 0x00000002
>>> +#define TC358775_LVCFG_LVDLINK__SHIFT 0
>>> +static inline u32 TC358775_LVCFG_LVDLINK(uint32_t val)
>>> +{
>>> + return ((val) << TC358775_LVCFG_LVDLINK__SHIFT) &
>>> + TC358775_LVCFG_LVDLINK__MASK;
>>> +}
>>> +
>>> +enum tc358775_ports {
>>> + TC358775_DSI_IN,
>>> + TC358775_LVDS_OUT0,
>>> + TC358775_LVDS_OUT1,
>>> +};
>>> +
>>> +struct tc_data {
>>> + struct i2c_client *i2c;
>>> + struct device *dev;
>>> +
>>> + struct drm_bridge bridge;
>>> + struct drm_bridge *panel_bridge;
>>> +
>>> + struct device_node *host_node;
>>> + struct mipi_dsi_device *dsi;
>>> + u8 num_dsi_lanes;
>>> +
>>> + struct regulator *vdd;
>>> + struct regulator *vddio;
>>> + struct gpio_desc *reset_gpio;
>>> + struct gpio_desc *stby_gpio;
>>> + bool dual_link; /* single-link or dual-link */
>>> +};
>>> +
>>> +static inline struct tc_data *bridge_to_tc(struct drm_bridge *b)
>>> +{
>>> + return container_of(b, struct tc_data, bridge);
>>> +}
>>> +
>>> +static void tc_bridge_pre_enable(struct drm_bridge *bridge)
>>> +{
>>> + struct tc_data *tc = bridge_to_tc(bridge);
>>> + struct device *dev = &tc->dsi->dev;
>>> + int ret;
>>> +
>>> + ret = regulator_enable(tc->vddio);
>>> + if (ret < 0)
>>> + dev_err(dev, "regulator vddio enable failed, %d\n", ret);
>>> + usleep_range(10000, 11000);
>>> +
>>> + ret = regulator_enable(tc->vdd);
>>> + if (ret < 0)
>>> + dev_err(dev, "regulator vdd enable failed, %d\n", ret);
>>> + usleep_range(10000, 11000);
>>> +
>>> + gpiod_set_value(tc->stby_gpio, 0);
>>> + usleep_range(10000, 11000);
>>> +
>>> + gpiod_set_value(tc->reset_gpio, 0);
>>> + usleep_range(10, 20);
>>> +}
>>> +
>>> +static void tc_bridge_post_disable(struct drm_bridge *bridge)
>>> +{
>>> + struct tc_data *tc = bridge_to_tc(bridge);
>>> + struct device *dev = &tc->dsi->dev;
>>> + int ret;
>>> +
>>> + ret = regulator_disable(tc->vddio);
>>> + if (ret < 0)
>>> + dev_err(dev, "regulator vddio disable failed, %d\n", ret);
>>> + usleep_range(10000, 11000);
>>> +
>>> + ret = regulator_disable(tc->vdd);
>>> + if (ret < 0)
>>> + dev_err(dev, "regulator vdd disable failed, %d\n", ret);
>>> + usleep_range(10000, 11000);
>>> +
>>> + gpiod_set_value(tc->stby_gpio, 1);
>>> + usleep_range(10000, 11000);
>>> +
>>> + gpiod_set_value(tc->reset_gpio, 1);
>>> + usleep_range(10, 20);
>>> +}
>>> +
>>> +static u32 d2l_read(struct i2c_client *i2c, u16 reg)
>>> +{
>>> + int ret;
>>> + u8 val[4];
>>> + u8 addr[] = {(reg >> 8) & 0xff, reg & 0xff};
>>> + u32 value;
>>> +
>>> + ret = i2c_master_send(i2c, addr, sizeof(reg));
>>> + if (ret < 0)
>>> + goto fail;
>>> +
>>> + ret = i2c_master_recv(i2c, val, sizeof(value));
>>> + if (ret < 0)
>>> + goto fail;
>>> +
>>> + value = val[3] << 24 | val[2] << 16 | val[1] << 8 | val[0];
>>> +
>>> + pr_debug("d2l: I2C : reg:%04x value:%08x\n", reg, value);
>>> +
>>> + return value;
>>> +
>>> +fail:
>>> + dev_err(&i2c->dev, "Error %d reading from subaddress 0x%x\n",
>>> + ret, reg);
>>> + return 0;
>>> +}
>>> +
>>> +static void d2l_write(struct i2c_client *i2c, u16 reg, u32 val)
>>> +{
>>> + u8 buf[6];
>>> + int ret;
>>> +
>>> + buf[0] = reg >> 8;
>>> + buf[1] = reg & 0xFF;
>>> + buf[2] = (val >> 0) & 0xFF;
>>> + buf[3] = (val >> 8) & 0xFF;
>>> + buf[4] = (val >> 16) & 0xFF;
>>> + buf[5] = (val >> 24) & 0xFF;
>>> +
>>> + ret = i2c_master_send(i2c, buf, ARRAY_SIZE(buf));
>>> + if (ret < 0)
>>> + dev_err(&i2c->dev, "Error %d writing to subaddress 0x%x\n",
>>> + ret, reg);
>>> +}
>>> +
>>> +/* helper function to access bus_formats */
>>> +static struct drm_connector *get_connector(struct drm_encoder *encoder)
>>> +{
>>> + struct drm_device *dev = encoder->dev;
>>> + struct drm_connector *connector;
>>> +
>>> + list_for_each_entry(connector, &dev->mode_config.connector_list, head)
>>> + if (connector->encoder == encoder)
>>> + return connector;
>>> +
>>> + return NULL;
>>> +}
>>> +
>>> +static void tc_bridge_enable(struct drm_bridge *bridge)
>>> +{
>>> + struct tc_data *tc = bridge_to_tc(bridge);
>>> + u32 hbpr, hpw, htime1, hfpr, hsize, htime2;
>>> + u32 vbpr, vpw, vtime1, vfpr, vsize, vtime2;
>>> + u32 val = 0;
>>> + u16 bus_formats;
>>> + struct drm_display_mode *mode;
>>> + struct drm_connector *connector = get_connector(bridge->encoder);
>>> +
>>> + mode = &bridge->encoder->crtc->state->adjusted_mode;
>>> +
>>> + hbpr = mode->htotal - mode->hsync_end;
>>> + hpw = mode->hsync_end - mode->hsync_start;
>>> + vbpr = mode->vtotal - mode->vsync_end;
>>> + vpw = mode->vsync_end - mode->vsync_start;
>>> +
>>> + htime1 = (hbpr << 16) + hpw;
>>> + vtime1 = (vbpr << 16) + vpw;
>>> +
>>> + hfpr = mode->hsync_start - mode->hdisplay;
>>> + hsize = mode->hdisplay;
>>> + vfpr = mode->vsync_start - mode->vdisplay;
>>> + vsize = mode->vdisplay;
>>> +
>>> + htime2 = (hfpr << 16) + hsize;
>>> + vtime2 = (vfpr << 16) + vsize;
>>> +
>>> + val = d2l_read(tc->i2c, IDREG);
>>> +
>>> + dev_info(tc->dev, "DSI2LVDS Chip ID.%02x Revision ID. %02x **\n",
>>> + (val >> 8) & 0xFF, val & 0xFF);
>>> +
>>> + d2l_write(tc->i2c, SYSRST, SYS_RST_REG | SYS_RST_DSIRX | SYS_RST_BM |
>>> + SYS_RST_LCD | SYS_RST_I2CM | SYS_RST_I2CS);
>>> + usleep_range(30000, 40000);
>>> +
>>> + d2l_write(tc->i2c, PPI_TX_RX_TA, TTA_GET | TTA_SURE);
>>> + d2l_write(tc->i2c, PPI_LPTXTIMECNT, LPX_PERIOD);
>>> + d2l_write(tc->i2c, PPI_D0S_CLRSIPOCOUNT, 3);
>>> + d2l_write(tc->i2c, PPI_D1S_CLRSIPOCOUNT, 3);
>>> + d2l_write(tc->i2c, PPI_D2S_CLRSIPOCOUNT, 3);
>>> + d2l_write(tc->i2c, PPI_D3S_CLRSIPOCOUNT, 3);
>>> +
>>> + val = ((L0EN << tc->num_dsi_lanes) - L0EN) | DSI_CLEN_BIT;
>>> + d2l_write(tc->i2c, PPI_LANEENABLE, val);
>>> + d2l_write(tc->i2c, DSI_LANEENABLE, val);
>>> +
>>> + d2l_write(tc->i2c, PPI_STARTPPI, PPI_START_FUNCTION);
>>> + d2l_write(tc->i2c, DSI_STARTDSI, DSI_RX_START);
>>> +
>>> + val = TC358775_VPCTRL_VSDELAY(21);
>>> +
>>> + bus_formats = connector->display_info.bus_formats[0];
>>> + dev_dbg(tc->dev, "bus_formats : %04x\n", bus_formats);
>>> +
>>> + if (bus_formats == MEDIA_BUS_FMT_RGB888_1X7X4_SPWG ||
>>> + bus_formats == MEDIA_BUS_FMT_RGB888_1X7X4_JEIDA) {
>>> + /* RGB888 */
>>> + val |= TC358775_VPCTRL_OPXLFMT(1);
>>> + d2l_write(tc->i2c, VPCTRL, val);
>>> + } else {
>>> + /* RGB666 */
>>> + val |= TC358775_VPCTRL_MSF(1);
>>> + d2l_write(tc->i2c, VPCTRL, val);
>>> + }
>>> +
>>> + d2l_write(tc->i2c, HTIM1, htime1);
>>> + d2l_write(tc->i2c, VTIM1, vtime1);
>>> + d2l_write(tc->i2c, HTIM2, htime2);
>>> + d2l_write(tc->i2c, VTIM2, vtime2);
>>> +
>>> + d2l_write(tc->i2c, VFUEN, VFUEN_EN);
>>> + d2l_write(tc->i2c, SYSRST, SYS_RST_LCD);
>>> + d2l_write(tc->i2c, LVPHY0, LV_PHY0_PRBS_ON(4) | LV_PHY0_ND(6));
>>> +
>>> + /* default jeida-24 */
>>> + if (bus_formats == MEDIA_BUS_FMT_RGB888_1X7X4_SPWG) {
>>> + /* vesa-24 */
>>> + d2l_write(tc->i2c, LV_MX0003, LV_MX(LVI_R0, LVI_R1, LVI_R2, LVI_R3));
>>> + d2l_write(tc->i2c, LV_MX0407, LV_MX(LVI_R4, LVI_R7, LVI_R5, LVI_G0));
>>> + d2l_write(tc->i2c, LV_MX0811, LV_MX(LVI_G1, LVI_G2, LVI_G6, LVI_G7));
>>> + d2l_write(tc->i2c, LV_MX1215, LV_MX(LVI_G3, LVI_G4, LVI_G5, LVI_B0));
>>> + d2l_write(tc->i2c, LV_MX1619, LV_MX(LVI_B6, LVI_B7, LVI_B1, LVI_B2));
>>> + d2l_write(tc->i2c, LV_MX2023, LV_MX(LVI_B3, LVI_B4, LVI_B5, LVI_L0));
>>> + d2l_write(tc->i2c, LV_MX2427, LV_MX(LVI_HS, LVI_VS, LVI_DE, LVI_R6));
>>> + }
>>> +
>>> + if (bus_formats == MEDIA_BUS_FMT_RGB666_1X7X3_SPWG) {
>>> + /* jeida-18 */
>>> + d2l_write(tc->i2c, LV_MX0003, LV_MX(LVI_R0, LVI_R1, LVI_R2, LVI_R3));
>>> + d2l_write(tc->i2c, LV_MX0407, LV_MX(LVI_R4, LVI_L0, LVI_R5, LVI_G0));
>>> + d2l_write(tc->i2c, LV_MX0811, LV_MX(LVI_G1, LVI_G2, LVI_L0, LVI_L0));
>>> + d2l_write(tc->i2c, LV_MX1215, LV_MX(LVI_G3, LVI_G4, LVI_G5, LVI_B0));
>>> + d2l_write(tc->i2c, LV_MX1619, LV_MX(LVI_L0, LVI_L0, LVI_B1, LVI_B2));
>>> + d2l_write(tc->i2c, LV_MX2023, LV_MX(LVI_B3, LVI_B4, LVI_B5, LVI_L0));
>>> + d2l_write(tc->i2c, LV_MX2427, LV_MX(LVI_HS, LVI_VS, LVI_DE, LVI_L0));
>>> + }
>>> +
>>> + d2l_write(tc->i2c, VFUEN, VFUEN_EN);
>>> +
>>> + val = LVCFG_LVEN_BIT;
>>> + if (tc->dual_link) {
>>> + val |= TC358775_LVCFG_LVDLINK(1);
>>> + val |= TC358775_LVCFG_PCLKDIV(DIVIDE_BY_6);
>>> + } else {
>>> + val |= TC358775_LVCFG_PCLKDIV(DIVIDE_BY_3);
>>> + }
>>> +
>>> + d2l_write(tc->i2c, LVCFG, val);
>>> +}
>>> +
>>> +static int tc_mode_valid(struct drm_bridge *bridge,
>>> + const struct drm_display_mode *mode)
>>> +{
>>> + struct tc_data *tc = bridge_to_tc(bridge);
>>> +
>>> + /* Maximum pixel clock speed 135MHz-single-link/270MHz-dual-link */
>>> + if ((mode->clock > 135000 && tc->dual_link) ||
>>> + (mode->clock > 270000 && tc->dual_link))
>>> + return MODE_CLOCK_HIGH;
>>> +
>>> + return MODE_OK;
>>> +}
>>> +
>>> +static int tc358775_parse_dt(struct device_node *np, struct tc_data *tc)
>>> +{
>>> + struct device_node *endpoint;
>>> + struct device_node *parent;
>>> + struct device_node *remote;
>>> + struct property *prop;
>>> + int len;
>>> +
>>> + endpoint = of_graph_get_endpoint_by_regs(tc->dev->of_node,
>>> + TC358775_DSI_IN, -1);
>>> + if (endpoint) {
>>> + /* dsi0_out node */
>>> + parent = of_graph_get_remote_port_parent(endpoint);
>>> + of_node_put(endpoint);
>>> + if (parent) {
>>> + /* dsi0 port 1 */
>>> + endpoint = of_graph_get_endpoint_by_regs(parent, 1, -1);
>>> + of_node_put(parent);
>>> + prop = of_find_property(endpoint, "data-lanes",
>>> + &len);
>>> + of_node_put(endpoint);
>>> + if (!prop) {
>>> + dev_err(tc->dev,
>>> + "failed to find data lane\n");
>>> + return -EPROBE_DEFER;
>>> + }
>>> + }
>>> + }
>>> +
>>> + tc->num_dsi_lanes = len / sizeof(u32);
>>> +
>>> + if (tc->num_dsi_lanes < 1 || tc->num_dsi_lanes > 4)
>>> + return -EINVAL;
>>> +
>>> + tc->host_node = of_graph_get_remote_node(np, 0, 0);
>>> + if (!tc->host_node)
>>> + return -ENODEV;
>>> +
>>> + of_node_put(tc->host_node);
>>> +
>>> + endpoint = of_graph_get_endpoint_by_regs(tc->dev->of_node,
>>> + TC358775_LVDS_OUT1, -1);
>>> + if (endpoint) {
>>> + remote = of_graph_get_remote_port_parent(endpoint);
>>> + of_node_put(endpoint);
>>> +
>>> + if (remote) {
>>> + if (of_device_is_available(remote))
>>> + tc->dual_link = true;
>>> + of_node_put(remote);
>>> + }
>>> + }
>>> +
>>> + dev_dbg(tc->dev, "no.of dsi lanes: %d\n", tc->num_dsi_lanes);
>>> + dev_dbg(tc->dev, "operating in %s-link mode\n",
>>> + tc->dual_link ? "dual" : "single");
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static int tc_bridge_attach(struct drm_bridge *bridge,
>>> + enum drm_bridge_attach_flags flags)
>>> +{
>>> + struct tc_data *tc = bridge_to_tc(bridge);
>>> + struct device *dev = &tc->i2c->dev;
>>> + struct mipi_dsi_host *host;
>>> + struct mipi_dsi_device *dsi;
>>> + int ret;
>>> +
>>> + const struct mipi_dsi_device_info info = { .type = "tc358775",
>>> + .channel = 0,
>>> + .node = NULL,
>>> + };
>>> +
>>> + host = of_find_mipi_dsi_host_by_node(tc->host_node);
>>> + if (!host) {
>>> + dev_err(dev, "failed to find dsi host\n");
>>> + return -EPROBE_DEFER;
>>> + }
>>> +
>>> + dsi = mipi_dsi_device_register_full(host, &info);
>>> + if (IS_ERR(dsi)) {
>>> + dev_err(dev, "failed to create dsi device\n");
>>> + ret = PTR_ERR(dsi);
>>> + goto err_dsi_device;
>>> + }
>>> +
>>> + tc->dsi = dsi;
>>> +
>>> + dsi->lanes = tc->num_dsi_lanes;
>>> + dsi->format = MIPI_DSI_FMT_RGB888;
>>> + dsi->mode_flags = MIPI_DSI_MODE_VIDEO;
>>> +
>>> + ret = mipi_dsi_attach(dsi);
>>> + if (ret < 0) {
>>> + dev_err(dev, "failed to attach dsi to host\n");
>>> + goto err_dsi_attach;
>>> + }
>>> +
>>> + /* Attach the panel-bridge to the dsi bridge */
>>> + return drm_bridge_attach(bridge->encoder, tc->panel_bridge,
>>> + &tc->bridge, flags);
>>> +err_dsi_attach:
>>> + mipi_dsi_device_unregister(dsi);
>>> +err_dsi_device:
>>> + return ret;
>>> +}
>>> +
>>> +static const struct drm_bridge_funcs tc_bridge_funcs = {
>>> + .attach = tc_bridge_attach,
>>> + .pre_enable = tc_bridge_pre_enable,
>>> + .enable = tc_bridge_enable,
>>> + .mode_valid = tc_mode_valid,
>>> + .post_disable = tc_bridge_post_disable,
>>> +};
>>> +
>>> +static int tc_probe(struct i2c_client *client, const struct i2c_device_id *id)
>>> +{
>>> + struct device *dev = &client->dev;
>>> + struct drm_panel *panel;
>>> + struct tc_data *tc;
>>> + int ret;
>>> +
>>> + tc = devm_kzalloc(dev, sizeof(*tc), GFP_KERNEL);
>>> + if (!tc)
>>> + return -ENOMEM;
>>> +
>>> + tc->dev = dev;
>>> + tc->i2c = client;
>>> +
>>> + ret = drm_of_find_panel_or_bridge(dev->of_node, TC358775_LVDS_OUT0,
>>> + 0, &panel, NULL);
>>> + if (ret < 0)
>>> + return ret;
>>> + if (!panel)
>>> + return -ENODEV;
>>> +
>>> + tc->panel_bridge = devm_drm_panel_bridge_add(dev, panel);
>>> + if (IS_ERR(tc->panel_bridge))
>>> + return PTR_ERR(tc->panel_bridge);
>>> +
>>> + ret = tc358775_parse_dt(dev->of_node, tc);
>>> + if (ret)
>>> + return ret;
>>> +
>>> + tc->vddio = devm_regulator_get(dev, "vddio-supply");
>>> + if (IS_ERR(tc->vddio)) {
>>> + ret = PTR_ERR(tc->vddio);
>>> + dev_err(dev, "vddio-supply not found\n");
>>> + return ret;
>>> + }
>>> +
>>> + tc->vdd = devm_regulator_get(dev, "vdd-supply");
>>> + if (IS_ERR(tc->vdd)) {
>>> + ret = PTR_ERR(tc->vddio);
>>> + dev_err(dev, "vdd-supply not found\n");
>>> + return ret;
>>> + }
>>> +
>>> + tc->stby_gpio = devm_gpiod_get(dev, "stby", GPIOD_OUT_HIGH);
>>> + if (IS_ERR(tc->stby_gpio)) {
>>> + ret = PTR_ERR(tc->stby_gpio);
>>> + dev_err(dev, "cannot get stby-gpio %d\n", ret);
>>> + return ret;
>>> + }
>>> +
>>> + tc->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
>>> + if (IS_ERR(tc->reset_gpio)) {
>>> + ret = PTR_ERR(tc->reset_gpio);
>>> + dev_err(dev, "cannot get reset-gpios %d\n", ret);
>>> + return ret;
>>> + }
>>> +
>>> + tc->bridge.funcs = &tc_bridge_funcs;
>>> + tc->bridge.of_node = dev->of_node;
>>> + drm_bridge_add(&tc->bridge);
>>> +
>>> + i2c_set_clientdata(client, tc);
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static int tc_remove(struct i2c_client *client)
>>> +{
>>> + struct tc_data *tc = i2c_get_clientdata(client);
>>> +
>>> + drm_bridge_remove(&tc->bridge);
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static const struct i2c_device_id tc358775_i2c_ids[] = {
>>> + { "tc358775", 0 },
>>> + { }
>>> +};
>>> +MODULE_DEVICE_TABLE(i2c, tc358775_i2c_ids);
>>> +
>>> +static const struct of_device_id tc358775_of_ids[] = {
>>> + { .compatible = "toshiba,tc358775", },
>>> + { }
>>> +};
>>> +MODULE_DEVICE_TABLE(of, tc358775_of_ids);
>>> +
>>> +static struct i2c_driver tc358775_driver = {
>>> + .driver = {
>>> + .name = "tc358775",
>>> + .of_match_table = tc358775_of_ids,
>>> + },
>>> + .id_table = tc358775_i2c_ids,
>>> + .probe = tc_probe,
>>> + .remove = tc_remove,
>>> +};
>>> +module_i2c_driver(tc358775_driver);
>>> +
>>> +MODULE_AUTHOR("Vinay Simha BN <simhavcs at gmail.com>");
>>> +MODULE_DESCRIPTION("TC358775 DSI/LVDS bridge driver");
>>> +MODULE_LICENSE("GPL v2");
>>>
>>
>
>
More information about the dri-devel
mailing list