[PATCH v3 2/2] arm64: dts: renesas: Add HiHope RZ/G2M board with idk-1110wr display

[Geert Uytterhoeven]

Hi Lad,

On Tue, Mar 10, 2020 at 9:42 PM Lad Prabhakar
<prabhakar.mahadev-lad.rj at bp.renesas.com> wrote:
> From: Fabrizio Castro <fabrizio.castro at bp.renesas.com>
>
> The HiHope RZ/G2M is advertised as compatible with panel idk-1110wr
> from Advantech, however the panel isn't sold alongside the board.
> A new dts, adding everything that's required to get the panel to
> work the HiHope RZ/G2M, is the most convenient way to support the
> HiHope RZ/G2M when it's connected to the idk-1110wr.
>
> Signed-off-by: Fabrizio Castro <fabrizio.castro at bp.renesas.com>
> Acked-by: Laurent Pinchart <laurent.pinchart at ideasonboard.com>
> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj at bp.renesas.com>

Thanks for picking up this patch!

> --- /dev/null
> +++ b/arch/arm64/boot/dts/renesas/r8a774a1-hihope-rzg2m-ex-idk-1110wr.dts
> @@ -0,0 +1,86 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Device Tree Source for the HiHope RZ/G2M sub board connected to an
> + * Advantech IDK-1110WR 10.1" LVDS panel
> + *
> + * Copyright (C) 2020 Renesas Electronics Corp.
> + */
> +
> +#include "r8a774a1-hihope-rzg2m-ex.dts"
> +
> +/ {
> +       backlight {
> +               compatible = "pwm-backlight";
> +               pwms = <&pwm0 0 50000>;
> +
> +               brightness-levels = <0 2 8 16 32 64 128 255>;
> +               default-brightness-level = <6>;
> +       };
> +
> +       panel-lvds {
> +               compatible = "advantech,idk-1110wr", "panel-lvds";
> +
> +               width-mm = <223>;
> +               height-mm = <125>;
> +
> +               data-mapping = "jeida-24";
> +
> +               panel-timing {
> +                       /* 1024x600 @60Hz */
> +                       clock-frequency = <51200000>;
> +                       hactive = <1024>;
> +                       vactive = <600>;
> +                       hsync-len = <240>;
> +                       hfront-porch = <40>;
> +                       hback-porch = <40>;
> +                       vfront-porch = <15>;
> +                       vback-porch = <10>;
> +                       vsync-len = <10>;
> +               };
> +
> +               port {
> +                       panel_in: endpoint {
> +                               remote-endpoint = <&lvds0_out>;
> +                       };
> +               };
> +       };

I believe the plan was to include the existing
rzg2-advantech-idk-1110wr-panel.dtsi instead, to provide the
panel-lvds node...

> +};
> +
> +&gpio1 {
> +       /*
> +        * When GP1_20 is LOW LVDS0 is connected to the LVDS connector
> +        * When GP1_20 is HIGH LVDS0 is connected to the LT8918L
> +        */
> +       lvds-connector-en-gpio {
> +               gpio-hog;
> +               gpios = <20 GPIO_ACTIVE_HIGH>;
> +               output-low;
> +               line-name = "lvds-connector-en-gpio";
> +       };
> +};
> +
> +&lvds0 {
> +       status = "okay";
> +
> +       ports {
> +               port at 1 {
> +                       lvds0_out: endpoint {
> +                               remote-endpoint = <&panel_in>;
> +                       };
> +               };
> +       };
> +};

... and the lvds_connector endpoint configuration.

The rest looks good to me.

Gr{oetje,eeting}s,

                        Geert

-- 
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds