[PATCH] display/bridge: dsi2lvds tc358775 driver

Vinay Simha B N simhavcs at gmail.com
Wed Mar 11 10:00:48 UTC 2020


Laurent Pinchart,

if we want to set to jeida-18 data mapping,
do we need to set DATA3 with "Logic 0" LVI_L0 ?

Please see reply inline.

On Fri, Mar 6, 2020 at 7:02 PM Laurent Pinchart
<laurent.pinchart at ideasonboard.com> wrote:
>
> Hi Vinay,
>
> Thank you for the patch.
>
> On Fri, Mar 06, 2020 at 06:06:36PM +0530, Vinay Simha B N wrote:
> > hi andrzej,
> >
> > I had a doubt In the tc358764 driver,VP_CTRL, VP_CTRL_VSDELAY(15) is
> > hardcoded to 15, but this has to be dynamic based on the resolution of
> > panel used?
> >
> > Please see the reply inline.
> >
> > On Tue, Mar 3, 2020 at 8:39 PM Andrzej Hajda <a.hajda at samsung.com> wrote:
> > > On 27.02.2020 15:03, Vinay Simha BN wrote:
> > > > dsi2lvds tc358775 bridge driver added
> > > > Tested in apq8016, ifc6309 board and panel
> > > > auo,b101xtn01
> > >
> > > Just FYI, there exists already TC358764/5 driver for similar hw, but
> > > controlled via DSI bus.
> >
> > There is not much difference between these two chips, but still the
> > dsi read access for 775 does not works.
> > TC358764/5 - 800Mbps per lane, 3.2Gbps
> > TC358775 - 1Gbps per lane, 4Gbps.
> >
> > tc358775 chip details -
> > https://download.t-firefly.com/product/RK3399/Docs/Chip%20Specifications/TC358774XBG_75XBG_V1%204nm.pdf
> > I am able to configure the tc358775 chip by i2c, but from dsi it fails
> > i tried accessing the tc358775 chip by dsi using apq8016-qcom , but it
> > fails to read the chip id itself.
> >
> > Please suggest if you any inputs for this issue.
> >
> > https://github.com/vinaysimhabn/kernel-msm/commits/5.6.0-rc3-dsi2lvds-dsi
> >
> > [    4.582405] tc358764 1a98000.dsi.0: read: 1408, addr: 0
> > [    4.582426] tc358764 1a98000.dsi.0: ID: 0x0
> > [    4.582451] tc358764 1a98000.dsi.0: error initializing bridge (-22)
> >
> > [    4.796220] dsi_cmds2buf_tx: cmd dma tx failed, type=0x24, data0=0x80, len=4
> > [    4.796244] [drm:msm_dsi_host_cmd_rx] data = 0x0 and ntohl(data) = 0x0
> > [    4.796266] [drm:msm_dsi_host_cmd_rx] data = 0x0 and ntohl(data) = 0x0
> > [    4.796288] [drm:msm_dsi_host_cmd_rx] data = 0x0 and ntohl(data) = 0x0
> > [    4.796310] [drm:msm_dsi_host_cmd_rx] data = 0x0 and ntohl(data) = 0x0
> > [    4.796319] msm_dsi_host_cmd_rx:Invalid response cmd
> >
> > > > Signed-off-by: Vinay Simha BN <simhavcs at gmail.com>
> > > > ---
> > > >  .../bindings/display/bridge/toshiba,tc358775.txt   | 106 ++++
> > >
> > > Bindings should be in separate patch and in yaml format.
> > >
> > > >  drivers/gpu/drm/bridge/Kconfig                     |  10 +
> > > >  drivers/gpu/drm/bridge/Makefile                    |   1 +
> > > >  drivers/gpu/drm/bridge/tc358775.c                  | 687 +++++++++++++++++++++
> > > >  4 files changed, 804 insertions(+)
> > > >  create mode 100644 Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt
> > > >  create mode 100644 drivers/gpu/drm/bridge/tc358775.c
> > > >
> > > > diff --git a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt
> > > > new file mode 100644
> > > > index 0000000..c4c364d
> > > > --- /dev/null
> > > > +++ b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358775.txt
> > > > @@ -0,0 +1,106 @@
> > > > +Toshiba TC358775 DSI to LVDS bridge bindings
> > > > +
> > > > +Required properties:
> > > > + - compatible: "toshiba,tc358775"
> > > > + - reg: i2c address of the bridge, 0x0f
> > > > + - tc, dsi-lanes: Number of DSI data lanes connected to the DSI host. It should
> > > > +  be one of 1, 2, 3 or 4.
> > > > + - tc, dual-link : To configure the LVDS transmitter either
> > > > +  as single-link or dual-link.
> > > > + - tc, data-format: To configure the data formats
> > > > +   0 for VESA standard, 1 for JEIDA standard
> > >
> > > IMO, three properties above should be received from downstream device in
> > > runtime, not hardcoded into DT, however I am not sure if frameworks
> > > support it.
>
> I assume Andrzej meant upstream device for the tc,dsi-lanes property.
> This should be exposed through the data-lanes property as described in
> media/video-interface.txt.

data-lanes mainly used for the interfaces of the hardware.
example : dsi, csi
In general panels/bridges either it will be hardcoded by setting in the
panel driver like this dsi->lanes = 4;
bridge  -> dsi2hdmi display/bridge/adi,adv7511.txt it wil be set by
adi,dsi-lanes
>
> The tc,dual-link property should be replaced by exposing two port nodes,
> one for each link, and connecting them appropriately. See
> display/bridge/thine,thc63lvd1024.txt for an example of DT bindings on
> the LVDS receiver side, and drivers/gpu/drm/rcar-du/rcar_lvds.c for an
> example implementation on the LVDS transmitter side.

Can we add two port nodes though it can give only 1 output? when
higher resolution panel used dual_link is enabled in LVCFG
>
> The tc,data-format property should be replaced by the data-mapping
> property on the downstream LVDS device (see display/panel/lvds.yaml) and
> queried at runtime.
>
> > > > + - vdd-supply: 1.2V LVDS Power Supply
> > > > + - vddio-supply: 1.8V IO Power Supply
> > > > + - stby-gpios: Standby pin, Low active
> > > > + - reset-gpios: Hardware reset,      Low active
> > > > +
> > > > +Required nodes:
> > > > +
> > > > +The TC358775 has two ports. Their connections are modelled using the OF
> > > > +graph bindings specified in Documentation/devicetree/bindings/graph.txt.
> > > > +
> > > > +- Video port 0 for the DSI input. The remote endpoint phandle should be a
> > > > +     reference to a valid mipi_dsi_host device node.
> > > > +- Video port 1 for the LVDS output.
> > > > +
> > > > +Example:
> > > > +
> > > > +     i2c at 78b8000 {
> > > > +             /* On High speed expansion */
> > > > +             label = "HS-I2C2";
> > > > +             status = "okay";
> > > > +
> > > > +             tc_bridge: bridge at f {
> > > > +                     status = "okay";
> > > > +
> > > > +                     compatible = "toshiba,tc358775";
> > > > +                     reg = <0x0f>;
> > > > +
> > > > +                     tc,dsi-lanes = <4>;
> > > > +                     tc,dual-link = <0>;
> > > > +                     tc,data-format = <1>;
> > > > +
> > > > +                     vdd-supply = <&pm8916_l2>;
> > > > +                     vddio-supply = <&pm8916_l6>;
> > > > +
> > > > +                     stby-gpio = <&msmgpio 99 GPIO_ACTIVE_LOW>;
> > > > +                     reset-gpio = <&msmgpio 72 GPIO_ACTIVE_LOW>;
> > > > +
> > > > +                     ports {
> > > > +                             #address-cells = <1>;
> > > > +                             #size-cells = <0>;
> > > > +
> > > > +                             port at 0 {
> > > > +                                     reg = <0>;
> > > > +                                     d2l_in: endpoint {
> > > > +                                             remote-endpoint = <&dsi0_out>;
> > > > +                                     };
> > > > +                             };
> > > > +
> > > > +                             port at 1 {
> > > > +                                     reg = <1>;
> > > > +                                     d2l_out: endpoint {
> > > > +                                             remote-endpoint = <&panel_in>;
> > > > +                                     };
> > > > +                             };
> > > > +                     };
> > > > +             };
> > > > +     };
> > > > +
> > > > +     panel: auo,b101xtn01 {
> > > > +                     status = "okay";
> > > > +                     compatible = "auo,b101xtn01";
> > > > +                     power-supply = <&pm8916_l14>;
> > > > +
> > > > +                     port {
> > > > +                             panel_in: endpoint {
> > > > +                                     remote-endpoint = <&d2l_out>;
> > > > +                             };
> > > > +                     };
> > > > +     };
> > > > +
> > > > +     mdss at 1a00000 {
> > > > +             status = "okay";
> > > > +
> > > > +             mdp at 1a01000 {
> > > > +                     status = "okay";
> > > > +             };
> > > > +
> > > > +             dsi at 1a98000 {
> > > > +                     status = "okay";
> > > > +                     ..
> > > > +                     ports {
> > > > +                             port at 1 {
> > > > +                                     dsi0_out: endpoint {
> > > > +                                             remote-endpoint = <&d2l_in>;
> > > > +                                             data-lanes = <0 1 2 3>;
> > > > +                                     };
> > > > +                             };
> > > > +                     };
> > > > +             };
> > > > +
> > > > +             dsi-phy at 1a98300 {
> > > > +                     status = "okay";
> > > > +                     ..
> > > > +             };
> > > > +     };
> > > > diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
> > > > index 8397bf7..d5528fa 100644
> > > > --- a/drivers/gpu/drm/bridge/Kconfig
> > > > +++ b/drivers/gpu/drm/bridge/Kconfig
> > > > @@ -133,6 +133,16 @@ config DRM_TOSHIBA_TC358767
> > > >       ---help---
> > > >         Toshiba TC358767 eDP bridge chip driver.
> > > >
> > > > +config DRM_TOSHIBA_TC358775
> > > > +        tristate "Toshiba TC358775 LVDS bridge"
> > > > +        depends on OF
> > > > +        select DRM_KMS_HELPER
> > > > +        select REGMAP_I2C
> > > > +        select DRM_PANEL
> > > > +     select DRM_MIPI_DSI
> > > > +        ---help---
> > > > +          Toshiba TC358775 LVDS bridge chip driver.
> > > > +
> > > >  config DRM_TI_TFP410
> > > >       tristate "TI TFP410 DVI/HDMI bridge"
> > > >       depends on OF
> > > > diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
> > > > index 1eb5376..9b2c512 100644
> > > > --- a/drivers/gpu/drm/bridge/Makefile
> > > > +++ b/drivers/gpu/drm/bridge/Makefile
> > > > @@ -12,6 +12,7 @@ obj-$(CONFIG_DRM_SII9234) += sii9234.o
> > > >  obj-$(CONFIG_DRM_THINE_THC63LVD1024) += thc63lvd1024.o
> > > >  obj-$(CONFIG_DRM_TOSHIBA_TC358764) += tc358764.o
> > > >  obj-$(CONFIG_DRM_TOSHIBA_TC358767) += tc358767.o
> > > > +obj-$(CONFIG_DRM_TOSHIBA_TC358775) += tc358775.o
> > > >  obj-$(CONFIG_DRM_I2C_ADV7511) += adv7511/
> > > >  obj-$(CONFIG_DRM_TI_SN65DSI86) += ti-sn65dsi86.o
> > > >  obj-$(CONFIG_DRM_TI_TFP410) += ti-tfp410.o
> > > > diff --git a/drivers/gpu/drm/bridge/tc358775.c b/drivers/gpu/drm/bridge/tc358775.c
> > > > new file mode 100644
> > > > index 0000000..3db0f49
> > > > --- /dev/null
> > > > +++ b/drivers/gpu/drm/bridge/tc358775.c
> > > > @@ -0,0 +1,687 @@
> > > > +// SPDX-License-Identifier: GPL-2.0
> > > > +/*
> > > > + * tc358775 DSI to LVDS bridge driver
> > > > + *
> > > > + * Copyright (C) 2020 InforceComputing
> > > > + * Author: Vinay Simha BN <vinaysimha at inforcecomputing.com>
> > > > + *
> > > > + * This program is free software; you can redistribute it and/or modify
> > > > + * it under the terms of the GNU General Public License as published by
> > > > + * the Free Software Foundation; either version 2 of the License, or
> > > > + * (at your option) any later version.
> > > > + *
> > > > + * This program is distributed in the hope that it will be useful,
> > > > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > > > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> > > > + * GNU General Public License for more details.
> > >
> > > You can drop these statements, SPDX identifier is enough.
> > >
> > > > + */
> > > > +
> > > > +/* #define DEBUG */
> > > > +/* #define TC358775_DEBUG */
> > >
> > > Please remove these development leftovers.
> > >
> > > > +#include <linux/clk.h>
> > > > +#include <linux/device.h>
> > > > +#include <linux/gpio/consumer.h>
> > > > +#include <linux/i2c.h>
> > > > +#include <linux/kernel.h>
> > > > +#include <linux/module.h>
> > > > +#include <linux/regmap.h>
> > > > +#include <linux/slab.h>
> > > > +#include <linux/regulator/consumer.h>
> > > Alphabetic order.
> > > > +
> > > > +#include <drm/drm_mipi_dsi.h>
> > > > +#include <drm/drm_atomic_helper.h>
> > > > +#include <drm/drm_crtc_helper.h>
> > > > +#include <drm/drm_dp_helper.h>
> > > > +#include <drm/drm_of.h>
> > > > +#include <drm/drm_panel.h>
> > > > +#include <drm/drm_bridge.h>
> > > > +#include <drm/drm_probe_helper.h>
> > > ditto
> > > > +
> > > > +/* Registers */
> > > > +
> > > > +/* DSI D-PHY Layer Registers */
> > > > +#define D0W_DPHYCONTTX  0x0004  /* Data Lane 0 DPHY Tx Control */
> > > > +#define CLW_DPHYCONTRX  0x0020  /* Clock Lane DPHY Rx Control */
> > > > +#define D0W_DPHYCONTRX  0x0024  /* Data Lane 0 DPHY Rx Control */
> > > > +#define D1W_DPHYCONTRX  0x0028  /* Data Lane 1 DPHY Rx Control */
> > > > +#define D2W_DPHYCONTRX  0x002C  /* Data Lane 2 DPHY Rx Control */
> > > > +#define D3W_DPHYCONTRX  0x0030  /* Data Lane 3 DPHY Rx Control */
> > > > +#define COM_DPHYCONTRX  0x0038  /* DPHY Rx Common Control */
> > > > +#define CLW_CNTRL       0x0040  /* Clock Lane Control */
> > > > +#define D0W_CNTRL       0x0044  /* Data Lane 0 Control */
> > > > +#define D1W_CNTRL       0x0048  /* Data Lane 1 Control */
> > > > +#define D2W_CNTRL       0x004C  /* Data Lane 2 Control */
> > > > +#define D3W_CNTRL       0x0050  /* Data Lane 3 Control */
> > > > +#define DFTMODE_CNTRL   0x0054  /* DFT Mode Control */
> > > > +
> > > > +/* DSI PPI Layer Registers */
> > > > +#define PPI_STARTPPI    0x0104  /* START control bit of PPI-TX function. */
> > > > +#define PPI_BUSYPPI     0x0108
> > > > +#define PPI_LINEINITCNT 0x0110  /* Line Initialization Wait Counter  */
> > > > +#define PPI_LPTXTIMECNT 0x0114
> > > > +#define PPI_LANEENABLE  0x0134  /* Enables each lane at the PPI layer. */
> > > > +#define PPI_TX_RX_TA    0x013C  /* DSI Bus Turn Around timing parameters */
> > > > +
> > > > +/* Analog timer function enable */
> > > > +#define PPI_CLS_ATMR    0x0140  /* Delay for Clock Lane in LPRX  */
> > > > +#define PPI_D0S_ATMR    0x0144  /* Delay for Data Lane 0 in LPRX */
> > > > +#define PPI_D1S_ATMR    0x0148  /* Delay for Data Lane 1 in LPRX */
> > > > +#define PPI_D2S_ATMR    0x014C  /* Delay for Data Lane 2 in LPRX */
> > > > +#define PPI_D3S_ATMR    0x0150  /* Delay for Data Lane 3 in LPRX */
> > > > +#define PPI_D0S_CLRSIPOCOUNT    0x0164
> > > > +
> > > > +#define PPI_D1S_CLRSIPOCOUNT    0x0168  /* For lane 1 */
> > > > +#define PPI_D2S_CLRSIPOCOUNT    0x016C  /* For lane 2 */
> > > > +#define PPI_D3S_CLRSIPOCOUNT    0x0170  /* For lane 3 */
> > > > +
> > > > +#define CLS_PRE         0x0180  /* Digital Counter inside of PHY IO */
> > > > +#define D0S_PRE         0x0184  /* Digital Counter inside of PHY IO */
> > > > +#define D1S_PRE         0x0188  /* Digital Counter inside of PHY IO */
> > > > +#define D2S_PRE         0x018C  /* Digital Counter inside of PHY IO */
> > > > +#define D3S_PRE         0x0190  /* Digital Counter inside of PHY IO */
> > > > +#define CLS_PREP        0x01A0  /* Digital Counter inside of PHY IO */
> > > > +#define D0S_PREP        0x01A4  /* Digital Counter inside of PHY IO */
> > > > +#define D1S_PREP        0x01A8  /* Digital Counter inside of PHY IO */
> > > > +#define D2S_PREP        0x01AC  /* Digital Counter inside of PHY IO */
> > > > +#define D3S_PREP        0x01B0  /* Digital Counter inside of PHY IO */
> > > > +#define CLS_ZERO        0x01C0  /* Digital Counter inside of PHY IO */
> > > > +#define D0S_ZERO        0x01C4  /* Digital Counter inside of PHY IO */
> > > > +#define D1S_ZERO        0x01C8  /* Digital Counter inside of PHY IO */
> > > > +#define D2S_ZERO        0x01CC  /* Digital Counter inside of PHY IO */
> > > > +#define D3S_ZERO        0x01D0  /* Digital Counter inside of PHY IO */
> > > > +
> > > > +#define PPI_CLRFLG      0x01E0  /* PRE Counters has reached set values */
> > > > +#define PPI_CLRSIPO     0x01E4  /* Clear SIPO values, Slave mode use only. */
> > > > +#define HSTIMEOUT       0x01F0  /* HS Rx Time Out Counter */
> > > > +#define HSTIMEOUTENABLE 0x01F4  /* Enable HS Rx Time Out Counter */
> > > > +#define DSI_STARTDSI    0x0204  /* START control bit of DSI-TX function */
> > > > +#define DSI_BUSYDSI     0x0208
> > > > +#define DSI_LANEENABLE  0x0210  /* Enables each lane at the Protocol layer. */
> > > > +#define DSI_LANESTATUS0 0x0214  /* Displays lane is in HS RX mode. */
> > > > +#define DSI_LANESTATUS1 0x0218  /* Displays lane is in ULPS or STOP state */
> > > > +
> > > > +#define DSI_INTSTATUS   0x0220  /* Interrupt Status */
> > > > +#define DSI_INTMASK     0x0224  /* Interrupt Mask */
> > > > +#define DSI_INTCLR      0x0228  /* Interrupt Clear */
> > > > +#define DSI_LPTXTO      0x0230  /* Low Power Tx Time Out Counter */
> > > > +
> > > > +#define DSIERRCNT       0x0300  /* DSI Error Count */
> > > > +#define APLCTRL         0x0400  /* Application Layer Control */
> > > > +#define RDPKTLN         0x0404  /* Command Read Packet Length */
> > > > +
> > > > +#define VPCTRL          0x0450  /* Video Path Control */
> > > > +#define HTIM1           0x0454  /* Horizontal Timing Control 1 */
> > > > +#define HTIM2           0x0458  /* Horizontal Timing Control 2 */
> > > > +#define VTIM1           0x045C  /* Vertical Timing Control 1 */
> > > > +#define VTIM2           0x0460  /* Vertical Timing Control 2 */
> > > > +#define VFUEN           0x0464  /* Video Frame Timing Update Enable */
> > > > +
> > > > +/* Mux Input Select for LVDS LINK Input */
> > > > +#define LVMX0003        0x0480  /* Bit 0 to 3 */
> > > > +#define LVMX0407        0x0484  /* Bit 4 to 7 */
> > > > +#define LVMX0811        0x0488  /* Bit 8 to 11 */
> > > > +#define LVMX1215        0x048C  /* Bit 12 to 15 */
> > > > +#define LVMX1619        0x0490  /* Bit 16 to 19 */
> > > > +#define LVMX2023        0x0494  /* Bit 20 to 23 */
> > > > +#define LVMX2427        0x0498  /* Bit 24 to 27 */
> > > > +
> > > > +#define LVCFG           0x049C  /* LVDS Configuration  */
> > > > +#define LVPHY0          0x04A0  /* LVDS PHY 0 */
> > > > +#define LVPHY1          0x04A4  /* LVDS PHY 1 */
> > > > +#define SYSSTAT         0x0500  /* System Status  */
> > > > +#define SYSRST          0x0504  /* System Reset  */
> > > > +/* GPIO Registers */
> > > > +#define GPIOC           0x0520  /* GPIO Control  */
> > > > +#define GPIOO           0x0524  /* GPIO Output  */
> > > > +#define GPIOI           0x0528  /* GPIO Input  */
> > > > +
> > > > +/* I2C Registers */
> > > > +#define I2CTIMCTRL      0x0540  /* I2C IF Timing and Enable Control */
> > > > +#define I2CMADDR        0x0544  /* I2C Master Addressing */
> > > > +#define WDATAQ          0x0548  /* Write Data Queue */
> > > > +#define RDATAQ          0x054C  /* Read Data Queue */
> > > > +
> > > > +/* Chip ID and Revision ID Register */
> > > > +#define IDREG           0x0580
> > > > +
> > > > +#define TC358775XBG_ID  0x00007500
> > > > +
> > > > +/* Debug Registers */
> > > > +#define DEBUG00         0x05A0  /* Debug */
> > > > +#define DEBUG01         0x05A4  /* LVDS Data */
> > > > +
> > > > +#define DSI_CLEN_BIT         BIT(0)
> > > > +#define DIVIDE_BY_3          3 /* PCLK=DCLK/3 */
> > > > +#define LVCFG_LVEN_BIT               BIT(0)
> > > > +
> > > > +#define L0EN BIT(1)
> > > > +
> > > > +#define TC358775_VPCTRL_VSDELAY__MASK        0x3FF00000
> > > > +#define TC358775_VPCTRL_VSDELAY__SHIFT       20
> > > > +static inline uint32_t TC358775_VPCTRL_VSDELAY(uint32_t val)
> > >
> > >
> > > Use u32 here and below, unit32_t is mainly for userspace interactions.
> > >
> > >
> > > > +{
> > > > +     return ((val) << TC358775_VPCTRL_VSDELAY__SHIFT) &
> > > > +                     TC358775_VPCTRL_VSDELAY__MASK;
> > > > +}
> > > > +
> > > > +#define TC358775_VPCTRL_OPXLFMT__MASK        0x00000100
> > > > +#define TC358775_VPCTRL_OPXLFMT__SHIFT       8
> > > > +static inline uint32_t TC358775_VPCTRL_OPXLFMT(uint32_t val)
> > > > +{
> > > > +     return ((val) << TC358775_VPCTRL_OPXLFMT__SHIFT) &
> > > > +                     TC358775_VPCTRL_OPXLFMT__MASK;
> > > > +}
> > > > +
> > > > +#define TC358775_VPCTRL_MSF__MASK    0x00000001
> > > > +#define TC358775_VPCTRL_MSF__SHIFT   0
> > > > +static inline uint32_t TC358775_VPCTRL_MSF(uint32_t val)
> > > > +{
> > > > +     return ((val) << TC358775_VPCTRL_MSF__SHIFT) &
> > > > +                     TC358775_VPCTRL_MSF__MASK;
> > > > +}
> > > > +
> > > > +#define TC358775_LVCFG_PCLKDIV__MASK 0x000000f0
> > > > +#define TC358775_LVCFG_PCLKDIV__SHIFT        4
> > > > +static inline uint32_t TC358775_LVCFG_PCLKDIV(uint32_t val)
> > > > +{
> > > > +     return ((val) << TC358775_LVCFG_PCLKDIV__SHIFT) &
> > > > +                     TC358775_LVCFG_PCLKDIV__MASK;
> > > > +}
> > > > +
> > > > +#define TC358775_LVCFG_LVDLINK__MASK                         0x00000002
> > > > +#define TC358775_LVCFG_LVDLINK__SHIFT                        0
> > > > +static inline uint32_t TC358775_LVCFG_LVDLINK(uint32_t val)
> > > > +{
> > > > +     return ((val) << TC358775_LVCFG_LVDLINK__SHIFT) &
> > > > +                     TC358775_LVCFG_LVDLINK__MASK;
> > > > +}
> > > > +
> > > > +static const struct reg_sequence tc_fixed_registers[] = {
> > > > +     { 0x013C, 0x00040006 },
> > > > +     { 0x0114, 0x00000004 },
> > > > +     { 0x0164, 0x00000003 },
> > > > +     { 0x0168, 0x00000003 },
> > > > +     { 0x016C, 0x00000003 },
> > > > +     { 0x0170, 0x00000003 },
> > >
> > > use macros instead of magic numbers.
> > >
> > > > +};
> > > > +
> > > > +static const struct reg_sequence tc_vesa_data_format_registers[] = {
> > > > +     { 0x0480, 0x03020100 },
> > > > +     { 0x0484, 0x08050704 },
> > > > +     { 0x0488, 0x0F0E0A09 },
> > > > +     { 0x048C, 0x100D0C0B },
> > > > +     { 0x0490, 0x12111716 },
> > > > +     { 0x0494, 0x1B151413 },
> > > > +     { 0x0498, 0x061A1918 },
> > > ditto
> > > > +};
> > > > +
> > > > +static const char * const regulator_names[] = {
> > > > +     "vdd",
> > > > +     "vddio"
> > > > +};
> > > > +
> > > > +struct tc_data {
> > > > +     struct i2c_client       *i2c;
> > > > +
> > > > +     struct device           *dev;
> > > > +     struct regmap           *regmap;
> > > > +
> > > > +     struct drm_bridge       bridge;
> > > > +     struct drm_connector    connector;
> > > > +     struct drm_panel        *panel;
> > > > +
> > > > +     enum drm_connector_status status;
> > > unused field
status used in tc->status = connector_status_connected;
> > > > +     struct device_node *host_node;
> > > > +     struct mipi_dsi_device *dsi;
> > > > +     u8 num_dsi_lanes;
> > > > +
> > > > +     struct regulator_bulk_data supplies[ARRAY_SIZE(regulator_names)];
> > > > +     struct gpio_desc        *reset_gpio;
> > > > +     struct gpio_desc        *stby_gpio;
> > > > +     u32                     rev;
> > > > +     u8                      dual_link; /* single-link or dual-link */
> > > > +     u8                      data_format; /* VESA or JEIDA */
> > > > +};
> > > > +
> > > > +static inline struct tc_data *bridge_to_tc(struct drm_bridge *b)
> > > > +{
> > > > +     return container_of(b, struct tc_data, bridge);
> > > > +}
> > > > +
> > > > +static inline struct tc_data *connector_to_tc(struct drm_connector *c)
> > > > +{
> > > > +     return container_of(c, struct tc_data, connector);
> > > > +}
> > > > +
> > > > +static void tc_bridge_pre_enable(struct drm_bridge *bridge)
> > > > +{
> > > > +     struct tc_data *tc = bridge_to_tc(bridge);
> > > > +     struct device *dev = &tc->dsi->dev;
> > > > +     int ret;
> > > > +
> > > > +     ret = regulator_bulk_enable(ARRAY_SIZE(tc->supplies), tc->supplies);
> > > > +     if (ret < 0) {
> > > > +             dev_err(dev, "regulator enable failed, %d\n", ret);
> > > > +             return;
> > > > +     }
> > > > +     mdelay(10);
>
> You should consider usleep_range() instead of mdelay() for large delays.
>
> > > > +
> > > > +     gpiod_set_value(tc->stby_gpio, 0);
> > > > +     mdelay(10);
> > > > +
> > > > +     gpiod_set_value(tc->reset_gpio, 0);
> > > > +     ndelay(50);
> > > > +
> > > > +     drm_panel_prepare(tc->panel);
> > > > +}
> > > > +
> > > > +static void tc_bridge_disable(struct drm_bridge *bridge)
> > > > +{
> > > > +     struct tc_data *tc = bridge_to_tc(bridge);
> > > > +     struct device *dev = &tc->dsi->dev;
> > > > +     int ret;
> > > > +
> > > > +     ret = regulator_bulk_disable(ARRAY_SIZE(tc->supplies), tc->supplies);
> > > > +     if (ret < 0)
> > > > +             dev_err(dev, "regulator disable failed, %d\n", ret);
> > > > +     mdelay(10);
> > > > +
> > > > +     gpiod_set_value(tc->stby_gpio, 1);
> > > > +     mdelay(10);
> > > > +
> > > > +     gpiod_set_value(tc->reset_gpio, 1);
> > > > +     ndelay(50);
> > > > +
> > > > +     drm_panel_disable(tc->panel);
> > >
> > > I suspect the order should be different - ie reverse to the one pre_enable.
 - as per the datasheet it is not in reverse order

> > >
> > > Moreover since it reverts pre_enable it should be put into post_disable
> > > (except drm_panel_disable).
> > >
> > > > +}
> > > > +
> > > > +static void tc_bridge_post_disable(struct drm_bridge *bridge)
> > > > +{
> > > > +     struct tc_data *tc = bridge_to_tc(bridge);
> > > > +
> > > > +     drm_panel_unprepare(tc->panel);
> > > > +}
> > > > +
> > > > +#ifdef TC358775_DEBUG
> > > > +static u32 d2l_read(struct tc_data *tc, u16 reg)
> > > > +{
> > > > +     int ret;
> > > > +     u32 data;
> > > > +
> > > > +     ret = regmap_bulk_read(tc->regmap, reg, &data, 1);
> > > > +     if (ret)
> > > > +             return ret;
> > > > +
> > > > +     pr_debug("d2l: I2C : reg:%04x value:%08x\n", reg, data);
> > > > +
> > > > +     return data;
> > > > +}
> > > > +#endif
> > >
> > > I guess this leftover can be removed as well.
> > >
> > > > +
> > > > +static int d2l_write(struct tc_data *tc, u16 reg, u32 data)
> > > > +{
> > > > +     int ret = 0;
> > > > +
> > > > +     ret = regmap_bulk_write(tc->regmap, reg, (u32[]) {data}, 1);
> > > > +
> > > > +#ifdef TC358775_DEBUG
> > > > +     d2l_read(tc, reg);
> > > > +#endif
> > > > +     return ret;
> > > > +}
> > > > +
> > > > +static void tc_bridge_enable(struct drm_bridge *bridge)
> > > > +{
> > > > +     struct tc_data *tc = bridge_to_tc(bridge);
> > > > +     int ret;
> > > > +     u32 hbpr, hpw, htime1, hfpr, hsize, htime2;
> > > > +     u32 vbpr, vpw, vtime1, vfpr, vsize, vtime2;
> > > > +     u32 val = 0;
> > > > +     struct drm_display_mode *mode;
> > > > +
> > > > +     mode = &bridge->encoder->crtc->state->adjusted_mode;
> > > > +
> > > > +     hbpr = 0;
> > > > +     hpw  = mode->hsync_end - mode->hsync_start;
> > > > +     vbpr = 0;
> > > > +     vpw  = mode->vsync_end - mode->vsync_start;
> > > > +
> > > > +     htime1 = (hbpr << 16) + hpw;
> > > > +     vtime1 = (vbpr << 16) + vpw;
> > > > +
> > > > +     hfpr = mode->hsync_start - mode->hdisplay;
> > > > +     hsize = mode->hdisplay;
> > > > +     vfpr = mode->vsync_start - mode->vdisplay;
> > > > +     vsize = mode->vdisplay;
> > > > +
> > > > +     htime2 = (hfpr << 16) + hsize;
> > > > +     vtime2 = (vfpr << 16) + vsize;
> > > > +
> > > > +     ret = regmap_read(tc->regmap, IDREG, &tc->rev);
> > > > +     if (ret) {
> > > > +             dev_err(tc->dev, "can not read device ID: %d\n", ret);
> > > > +             return;
> > > > +     }
> > > > +     pr_debug("tc IDREG %04x Rev. %08x\n", IDREG, tc->rev);
> > > > +
> > > > +     d2l_write(tc, SYSRST, 0x000000FF);
> > > > +     mdelay(30);
> > > > +
> > > > +     ret = regmap_register_patch(tc->regmap,
> > > > +                                 tc_fixed_registers,
> > > > +                                 ARRAY_SIZE(tc_fixed_registers));
> > > > +     if (ret)
> > > > +             return;
> > > > +
> > > > +     val = ((L0EN << tc->num_dsi_lanes) - L0EN) | DSI_CLEN_BIT;
> > > > +     d2l_write(tc, PPI_LANEENABLE, val);
> > > > +     d2l_write(tc, DSI_LANEENABLE, val);
> > > > +
> > > > +     d2l_write(tc, PPI_STARTPPI, 0x00000001);
> > > > +     d2l_write(tc, DSI_STARTDSI, 0x00000001);
> > > > +
> > > > +     val = TC358775_VPCTRL_VSDELAY(21); //TODO : to set the dynamic value
> >
> > Any suggestion how to set dynamic value for Vsyncdelay?
> >
> > > > +
> > > > +     if (tc->connector.display_info.bpc == 8) {/* RGB888 */
> > > > +             val |= TC358775_VPCTRL_OPXLFMT(1);
> > > > +             d2l_write(tc, VPCTRL, val);
> > > > +     } else {                                /* RGB666 */
> > > > +             val |= TC358775_VPCTRL_MSF(1);
> > > > +             d2l_write(tc, VPCTRL, val);
> > > > +     }
> > > > +
> > > > +     d2l_write(tc, HTIM1, htime1);
> > > > +     d2l_write(tc, VTIM1, vtime1);
> > > > +     d2l_write(tc, HTIM2, htime2);
> > > > +     d2l_write(tc, VTIM2, vtime2);
> > > > +
> > > > +     d2l_write(tc, VFUEN, 0x00000001);
> > > > +     d2l_write(tc, SYSRST, 0x00000004);
> > > > +     d2l_write(tc, LVPHY0, 0x00040006);
> > > > +
> > > > +     if (tc->data_format) { /* Data Format VESA=0 , JEIDA=1 */
> > > > +             ret = regmap_register_patch
> > > > +                     (tc->regmap,
> > > > +                      tc_vesa_data_format_registers,
> > > > +                      ARRAY_SIZE(tc_vesa_data_format_registers));
> > > > +             if (ret)
> > > > +                     return;
> > > > +     }
> > > > +
> > > > +     d2l_write(tc, VFUEN, 0x00000001);
> > > > +
> > > > +     val = TC358775_LVCFG_PCLKDIV(DIVIDE_BY_3) | LVCFG_LVEN_BIT;
> > > > +     if (tc->dual_link)
> > > > +             val |= TC358775_LVCFG_LVDLINK(1);
> > > > +
> > > > +     d2l_write(tc, LVCFG, val);
> > > > +
> > > > +     drm_panel_enable(tc->panel);
> > > > +}
> > > > +
> > > > +static int tc_connector_get_modes(struct drm_connector *connector)
> > > > +{
> > > > +     struct tc_data *tc = connector_to_tc(connector);
> > > > +     struct edid *edid;
> > > > +     unsigned int count;
> > > > +
> > > > +     if (tc->panel && tc->panel->funcs && tc->panel->funcs->get_modes) {
> > > > +             count = tc->panel->funcs->get_modes(tc->panel, connector);
> > > > +             if (count > 0)
> > > > +                     return count;
> > > > +     }
> > > > +
> > > > +     edid = drm_get_edid(connector, tc->i2c->adapter);
> > > > +     if (!edid)
> > > > +             return 0;
> > > > +
> > > > +     drm_connector_update_edid_property(connector, edid);
> > > > +     count = drm_add_edid_modes(connector, edid);
> > > > +     kfree(edid);
> > > > +
> > > > +     return count;
> > > > +}
> > > > +
> > > > +static int tc_connector_mode_valid(struct drm_connector *connector,
> > > > +                                struct drm_display_mode *mode)
> > > > +{
> > > > +     struct tc_data *tc = connector_to_tc(connector);
> > > > +
> > > > +     /* Maximum pixel clock speed 135MHz-single-link/270MHz-dual-link */
> > > > +     if ((mode->clock > 135000 && tc->dual_link == 0) ||
> > > > +         (mode->clock > 270000 && tc->dual_link == 1))
> > > > +             return MODE_CLOCK_HIGH;
> > > > +
> > > > +     return MODE_OK;
> > > > +}
>
> This should be replaced by the bridge .mode_valid() operation, as it's
> related to the bridge, not the connector.
>
> > > > +
> > > > +static struct drm_encoder *
> > > > +tc_connector_best_encoder(struct drm_connector *connector)
> > > > +{
> > > > +     struct tc_data *tc = connector_to_tc(connector);
> > > > +
> > > > +     return tc->bridge.encoder;
> > > > +}
> > > > +
> > > > +static const struct drm_connector_helper_funcs tc_connector_helper_funcs = {
> > > > +     .get_modes = tc_connector_get_modes,
> > > > +     .mode_valid = tc_connector_mode_valid,
> > > > +     .best_encoder = tc_connector_best_encoder,
> > > > +};
> > > > +
> > > > +static const struct drm_connector_funcs tc_connector_funcs = {
> > > > +     .fill_modes = drm_helper_probe_single_connector_modes,
> > > > +     .destroy = drm_connector_cleanup,
> > > > +     .reset = drm_atomic_helper_connector_reset,
> > > > +     .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
> > > > +     .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
> > > > +};
> > > > +
> > > > +int tc358775_parse_dt(struct device_node *np, struct tc_data *tc)
> > > > +{
> > > > +     u32 num_lanes;
> > > > +     u8 dual_link, data_format;
> > > > +
> > > > +     of_property_read_u8(np, "tc,dual-link", &dual_link);
> > > > +     of_property_read_u8(np, "tc,data-format", &data_format);
> > > > +     of_property_read_u32(np, "tc,dsi-lanes", &num_lanes);
> > > > +
> > > > +     if (num_lanes < 1 || num_lanes > 4)
> > > > +             return -EINVAL;
> > > > +
> > > > +     tc->num_dsi_lanes = num_lanes;
> > > > +     tc->dual_link = dual_link;
> > > > +     tc->data_format = data_format;
> > > > +
> > > > +     tc->host_node = of_graph_get_remote_node(np, 0, 0);
> > > > +     if (!tc->host_node)
> > > > +             return -ENODEV;
> > > > +
> > > > +     of_node_put(tc->host_node);
> > > > +
> > > > +     return 0;
> > > > +}
> > > > +
> > > > +int tc358775_attach_dsi(struct tc_data *tc)
> > > > +{
> > > > +     struct device *dev = &tc->i2c->dev;
> > > > +     struct mipi_dsi_host *host;
> > > > +     struct mipi_dsi_device *dsi;
> > > > +     int ret = 0;
> > > > +     const struct mipi_dsi_device_info info = { .type = "tc358775",
> > > > +                                                     .channel = 0,
> > > > +                                                     .node = NULL,
> > > > +                                             };
> > > > +
> > > > +     host = of_find_mipi_dsi_host_by_node(tc->host_node);
> > > > +     if (!host) {
> > > > +             dev_err(dev, "failed to find dsi host\n");
> > > > +             return -EPROBE_DEFER;
> > > > +     }
> > > > +
> > > > +     dsi = mipi_dsi_device_register_full(host, &info);
> > > > +     if (IS_ERR(dsi)) {
> > > > +             dev_err(dev, "failed to create dsi device\n");
> > > > +             ret = PTR_ERR(dsi);
> > > > +             goto err_dsi_device;
> > > > +     }
> > > > +
> > > > +     tc->dsi = dsi;
> > > > +
> > > > +     dsi->lanes = tc->num_dsi_lanes;
> > > > +     dsi->format = MIPI_DSI_FMT_RGB888;
> > > > +     dsi->mode_flags = MIPI_DSI_MODE_VIDEO;
> > > > +
> > > > +     ret = mipi_dsi_attach(dsi);
> > > > +     if (ret < 0) {
> > > > +             dev_err(dev, "failed to attach dsi to host\n");
> > > > +             goto err_dsi_attach;
> > > > +     }
> > > > +
> > > > +     return 0;
> > > > +
> > > > +err_dsi_attach:
> > > > +     mipi_dsi_device_unregister(dsi);
> > > > +err_dsi_device:
> > > > +     return ret;
> > > > +}
> > > > +
> > > > +static int tc_bridge_attach(struct drm_bridge *bridge)
> > > > +{
> > > > +     struct tc_data *tc = bridge_to_tc(bridge);
> > > > +     struct drm_device *drm = bridge->dev;
> > > > +     int ret;
> > > > +
> > > > +     /* Create LVDS connector */
> > > > +     drm_connector_helper_add(&tc->connector, &tc_connector_helper_funcs);
> > > > +     ret = drm_connector_init(drm, &tc->connector, &tc_connector_funcs,
> > > > +                              DRM_MODE_CONNECTOR_LVDS);
> > > > +     if (ret)
> > > > +             return ret;
> > > > +
> > > > +     if (tc->panel)
> > > > +             drm_panel_attach(tc->panel, &tc->connector);
> > > > +
> > > > +     drm_connector_attach_encoder(&tc->connector, tc->bridge.encoder);
> > > > +
> > > > +     ret = tc358775_attach_dsi(tc);
> > >
> > > Ignored retval.
> > >
> > > > +
> > > > +     return 0;
> > > > +}
> > > > +
> > > > +static const struct drm_bridge_funcs tc_bridge_funcs = {
> > > > +     .attach = tc_bridge_attach,
> > > > +     .pre_enable = tc_bridge_pre_enable,
> > > > +     .enable = tc_bridge_enable,
> > > > +     .disable = tc_bridge_disable,
> > > > +     .post_disable = tc_bridge_post_disable,
> > > > +};
> > > > +
> > > > +static const struct regmap_config tc_regmap_config = {
> > > > +     .name = "tc358775",
> > > > +     .reg_bits = 16,
> > > > +     .val_bits = 32,
> > > > +     .reg_stride = 4,
> > > > +     .max_register = 0x05A8,
> > > > +     .cache_type = REGCACHE_RBTREE,
> > > > +     .reg_format_endian = REGMAP_ENDIAN_BIG,
> > > > +     .val_format_endian = REGMAP_ENDIAN_LITTLE,
> > > > +};
> > > > +
> > > > +static int tc_probe(struct i2c_client *client, const struct i2c_device_id *id)
> > > > +{
> > > > +     struct device *dev = &client->dev;
> > > > +     struct tc_data *tc;
> > > > +     int ret;
> > > > +     unsigned int i;
> > > > +
> > > > +     tc = devm_kzalloc(dev, sizeof(*tc), GFP_KERNEL);
> > > > +     if (!tc)
> > > > +             return -ENOMEM;
> > > > +
> > > > +     tc->dev = dev;
> > > > +     tc->i2c = client;
> > > > +     tc->status = connector_status_connected;
> > > > +
> > > > +     /* port at 1 is the output port */
> > > > +     ret = drm_of_find_panel_or_bridge(dev->of_node, 1, 0, &tc->panel, NULL);
> > > > +     if (ret && ret != -ENODEV)
> > > > +             return ret;
>
> You should support cases where the next device is a bridge. I recommand
> wrapping the panel in a drm_panel_bridge with drm_panel_bridge_add(),
> and then handling the next component as a bridge in all code paths. This
> will allow removing manual enable/disable of panels above, as bridge
> chaining is handled automatically. drm_panel_bridge creates a
> drm_connector, so you can drop your manual connector implementation
> here, simplifying the code.
>
i am not clear on this drm_panel_bridge_add() usage, please
clarify/any reference would be helpful.
> > > > +
> > > > +     ret = tc358775_parse_dt(dev->of_node, tc);
> > > > +     if (ret)
> > > > +             return ret;
> > > > +
> > > > +     for (i = 0; i < ARRAY_SIZE(tc->supplies); i++)
> > > > +             tc->supplies[i].supply = regulator_names[i];
> > > > +
> > > > +     ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(tc->supplies),
> > > > +                                   tc->supplies);
> > > > +     if (ret < 0)
> > > > +             dev_err(dev, "failed to init regulator, ret=%d\n", ret);
> > > > +
> > > > +     tc->stby_gpio = devm_gpiod_get(dev, "stby", GPIOD_OUT_HIGH);
> > > > +     if (IS_ERR(tc->stby_gpio)) {
> > > > +             ret = PTR_ERR(tc->stby_gpio);
> > > > +             dev_err(dev, "cannot get stby-gpio %d\n", ret);
> > > > +             return ret;
> > > > +     }
> > > > +
> > > > +     tc->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
> > > > +     if (IS_ERR(tc->reset_gpio)) {
> > > > +             ret = PTR_ERR(tc->reset_gpio);
> > > > +             dev_err(dev, "cannot get reset-gpios %d\n", ret);
> > > > +             return ret;
> > > > +     }
> > > > +
> > > > +     tc->regmap = devm_regmap_init_i2c(client, &tc_regmap_config);
> > > > +     if (IS_ERR(tc->regmap)) {
> > > > +             ret = PTR_ERR(tc->regmap);
> > > > +             dev_err(dev, "Failed to initialize regmap: %d\n", ret);
> > > > +             return ret;
> > > > +     }
> > > > +
> > > > +     tc->bridge.funcs = &tc_bridge_funcs;
> > > > +     tc->bridge.of_node = dev->of_node;
> > > > +     drm_bridge_add(&tc->bridge);
> > > > +
> > > > +     i2c_set_clientdata(client, tc);
> > > > +
> > > > +     return 0;
> > > > +}
> > > > +
> > > > +static int tc_remove(struct i2c_client *client)
> > > > +{
> > > > +     struct tc_data *tc = i2c_get_clientdata(client);
> > > > +
> > > > +     drm_bridge_remove(&tc->bridge);
> > > > +
> > > > +     return 0;
> > > > +}
> > > > +
> > > > +static const struct i2c_device_id tc358775_i2c_ids[] = {
> > > > +     { "tc358775", 0 },
> > > > +     { }
> > > > +};
> > > > +MODULE_DEVICE_TABLE(i2c, tc358775_i2c_ids);
> > > > +
> > > > +static const struct of_device_id tc358775_of_ids[] = {
> > > > +     { .compatible = "toshiba,tc358775", },
> > > > +     { }
> > > > +};
> > > > +MODULE_DEVICE_TABLE(of, tc358775_of_ids);
> > > > +
> > > > +static struct i2c_driver tc358775_driver = {
> > > > +     .driver = {
> > > > +             .name = "tc358775",
> > > > +             .of_match_table = tc358775_of_ids,
> > > > +     },
> > > > +     .id_table = tc358775_i2c_ids,
> > > > +     .probe = tc_probe,
> > > > +     .remove = tc_remove,
> > > > +};
> > > > +module_i2c_driver(tc358775_driver);
> > > > +
> > > > +MODULE_AUTHOR("Vinay Simha BN <vinaysimha at inforcecomputing.com>");
> > > > +MODULE_DESCRIPTION("tc358775 LVDS encoder driver");
> > >
> > > maybe  better:
> > >
> > > tc358775 DSI/LVDS bridge driver
> > >
> > > > +MODULE_LICENSE("GPL v2");
>
> --
> Regards,
>
> Laurent Pinchart



-- 
regards,
vinaysimha


More information about the dri-devel mailing list