[PATCH 5/8] dt-bindings: mtd: Convert ingenic, jz4780-nand.txt to YAML
Rob Herring
robh at kernel.org
Mon May 11 22:58:39 UTC 2020
On Sun, Apr 26, 2020 at 08:58:53PM +0200, Paul Cercueil wrote:
> Convert the ingenic,jz4780-nand.txt doc file to ingenic,nand.yaml.
>
> Signed-off-by: Paul Cercueil <paul at crapouillou.net>
> ---
> .../bindings/mtd/ingenic,jz4780-nand.txt | 92 ------------
> .../devicetree/bindings/mtd/ingenic,nand.yaml | 133 ++++++++++++++++++
> 2 files changed, 133 insertions(+), 92 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
> create mode 100644 Documentation/devicetree/bindings/mtd/ingenic,nand.yaml
>
> diff --git a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
> deleted file mode 100644
> index c02259353327..000000000000
> --- a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
> +++ /dev/null
> @@ -1,92 +0,0 @@
> -* Ingenic JZ4780 NAND/ECC
> -
> -This file documents the device tree bindings for NAND flash devices on the
> -JZ4780. NAND devices are connected to the NEMC controller (described in
> -memory-controllers/ingenic,jz4780-nemc.txt), and thus NAND device nodes must
> -be children of the NEMC node.
> -
> -Required NAND controller device properties:
> -- compatible: Should be one of:
> - * ingenic,jz4740-nand
> - * ingenic,jz4725b-nand
> - * ingenic,jz4780-nand
> -- reg: For each bank with a NAND chip attached, should specify a bank number,
> - an offset of 0 and a size of 0x1000000 (i.e. the whole NEMC bank).
> -
> -Optional NAND controller device properties:
> -- ecc-engine: To make use of the hardware ECC controller, this
> - property must contain a phandle for the ECC controller node. The required
> - properties for this node are described below. If this is not specified,
> - software ECC will be used instead.
> -
> -Optional children nodes:
> -- Individual NAND chips are children of the NAND controller node.
> -
> -Required children node properties:
> -- reg: An integer ranging from 1 to 6 representing the CS line to use.
> -
> -Optional children node properties:
> -- nand-ecc-step-size: ECC block size in bytes.
> -- nand-ecc-strength: ECC strength (max number of correctable bits).
> -- nand-ecc-mode: String, operation mode of the NAND ecc mode. "hw" by default
> -- nand-on-flash-bbt: boolean to enable on flash bbt option, if not present false
> -- rb-gpios: GPIO specifier for the busy pin.
> -- wp-gpios: GPIO specifier for the write protect pin.
> -
> -Optional child node of NAND chip nodes:
> -- partitions: see Documentation/devicetree/bindings/mtd/partition.txt
> -
> -Example:
> -
> -nemc: nemc at 13410000 {
> - ...
> -
> - nandc: nand-controller at 1 {
> - compatible = "ingenic,jz4780-nand";
> - reg = <1 0 0x1000000>; /* Bank 1 */
> -
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - ecc-engine = <&bch>;
> -
> - nand at 1 {
> - reg = <1>;
> -
> - nand-ecc-step-size = <1024>;
> - nand-ecc-strength = <24>;
> - nand-ecc-mode = "hw";
> - nand-on-flash-bbt;
> -
> - rb-gpios = <&gpa 20 GPIO_ACTIVE_LOW>;
> - wp-gpios = <&gpf 22 GPIO_ACTIVE_LOW>;
> -
> - partitions {
> - #address-cells = <2>;
> - #size-cells = <2>;
> - ...
> - }
> - };
> - };
> -};
> -
> -The ECC controller is a separate SoC component used for error correction on
> -NAND devices. The following is a description of the device properties for a
> -ECC controller.
> -
> -Required ECC properties:
> -- compatible: Should be one of:
> - * ingenic,jz4740-ecc
> - * ingenic,jz4725b-bch
> - * ingenic,jz4780-bch
> -- reg: Should specify the ECC controller registers location and length.
> -- clocks: Clock for the ECC controller.
> -
> -Example:
> -
> -bch: bch at 134d0000 {
> - compatible = "ingenic,jz4780-bch";
> - reg = <0x134d0000 0x10000>;
> -
> - clocks = <&cgu JZ4780_CLK_BCH>;
> -};
> diff --git a/Documentation/devicetree/bindings/mtd/ingenic,nand.yaml b/Documentation/devicetree/bindings/mtd/ingenic,nand.yaml
> new file mode 100644
> index 000000000000..0e4cb1b55385
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mtd/ingenic,nand.yaml
> @@ -0,0 +1,133 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/mtd/ingenic,nand.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Ingenic SoCs NAND controller devicetree bindings
> +
> +maintainers:
> + - Paul Cercueil <paul at crapouillou.net>
> +
> +allOf:
> + - $ref: ../memory-controllers/ingenic,nemc-client.yaml#
You don't need this here because the schema is already applied with the
parent's schema.
> + - $ref: nand-controller.yaml#
> +
> +properties:
> + compatible:
> + enum:
> + - ingenic,jz4740-nand
> + - ingenic,jz4725b-nand
> + - ingenic,jz4780-nand
> +
> + reg:
> + items:
> + - description: Bank number, offset and size of first attached NAND chip
> + - description: Bank number, offset and size of second attached NAND chip
> + - description: Bank number, offset and size of third attached NAND chip
> + - description: Bank number, offset and size of fourth attached NAND chip
> + minItems: 1
> +
> + ecc-engine: true
> +
> +patternProperties:
> + "^nand@[a-f0-9]$":
> + type: object
> + properties:
> + rb-gpios:
> + description: GPIO specifier for the busy pin.
> + maxItems: 1
> +
> + wp-gpios:
> + description: GPIO specifier for the write-protect pin.
> + maxItems: 1
> +
> + "^partitions$":
This is at the wrong level. It should be under 'nand at ...' node.
It is also not a pattern.
> + type: object
> + description:
> + Node containing description of fixed partitions.
> + See Documentation/devicetree/bindings/mtd/partition.txt
> +
> +required:
> + - compatible
> + - reg
> +
> +examples:
> + - |
> + #include <dt-bindings/clock/jz4780-cgu.h>
> + nemc: memory-controller at 13410000 {
> + compatible = "ingenic,jz4780-nemc";
> + reg = <0x13410000 0x10000>;
> + #address-cells = <2>;
> + #size-cells = <1>;
> + ranges = <1 0 0x1b000000 0x1000000>,
> + <2 0 0x1a000000 0x1000000>,
> + <3 0 0x19000000 0x1000000>,
> + <4 0 0x18000000 0x1000000>,
> + <5 0 0x17000000 0x1000000>,
> + <6 0 0x16000000 0x1000000>;
> +
> + clocks = <&cgu JZ4780_CLK_NEMC>;
> +
> + nand-controller at 1 {
> + compatible = "ingenic,jz4780-nand";
> + reg = <1 0 0x1000000>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ecc-engine = <&bch>;
> +
> + ingenic,nemc-tAS = <10>;
> + ingenic,nemc-tAH = <5>;
> + ingenic,nemc-tBP = <10>;
> + ingenic,nemc-tAW = <15>;
> + ingenic,nemc-tSTRV = <100>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pins_nemc>;
> +
> + nand at 1 {
> + reg = <1>;
> +
> + nand-ecc-step-size = <1024>;
> + nand-ecc-strength = <24>;
> + nand-ecc-mode = "hw";
> + nand-on-flash-bbt;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pins_nemc_cs1>;
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + partition at 0 {
> + label = "u-boot-spl";
> + reg = <0x0 0x0 0x0 0x800000>;
> + };
> +
> + partition at 800000 {
> + label = "u-boot";
> + reg = <0x0 0x800000 0x0 0x200000>;
> + };
> +
> + partition at a00000 {
> + label = "u-boot-env";
> + reg = <0x0 0xa00000 0x0 0x200000>;
> + };
> +
> + partition at c00000 {
> + label = "boot";
> + reg = <0x0 0xc00000 0x0 0x4000000>;
> + };
> +
> + partition at 4c00000 {
> + label = "system";
> + reg = <0x0 0x4c00000 0x1 0xfb400000>;
> + };
> + };
> + };
> + };
> + };
> --
> 2.26.2
>
More information about the dri-devel
mailing list