[PATCH 30/33] docs: ABI: cleanup several ABI documents
Jinpu Wang
jinpu.wang at cloud.ionos.com
Fri Oct 30 07:52:54 UTC 2020
On Wed, Oct 28, 2020 at 3:23 PM Mauro Carvalho Chehab
<mchehab+huawei at kernel.org> wrote:
>
> There are some ABI documents that, while they don't generate
> any warnings, they have issues when parsed by get_abi.pl script
> on its output result.
>
> Address them, in order to provide a clean output.
>
> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei at kernel.org>
> ---
> Documentation/ABI/obsolete/sysfs-class-dax | 8 +-
> .../ABI/obsolete/sysfs-driver-hid-roccat-pyra | 3 +
> Documentation/ABI/removed/devfs | 1 +
> Documentation/ABI/removed/raw1394 | 1 +
> Documentation/ABI/removed/sysfs-class-rfkill | 2 +-
> Documentation/ABI/removed/video1394 | 1 +
> Documentation/ABI/stable/firewire-cdev | 63 ++---
> Documentation/ABI/stable/sysfs-acpi-pmprofile | 4 +-
> Documentation/ABI/stable/sysfs-bus-w1 | 1 +
> Documentation/ABI/stable/sysfs-class-tpm | 4 +-
> Documentation/ABI/stable/sysfs-driver-speakup | 4 +
> Documentation/ABI/testing/configfs-most | 135 +++++++----
> .../ABI/testing/configfs-usb-gadget-ecm | 12 +-
> .../ABI/testing/configfs-usb-gadget-eem | 10 +-
> .../ABI/testing/configfs-usb-gadget-loopback | 6 +-
> .../testing/configfs-usb-gadget-mass-storage | 18 +-
> .../ABI/testing/configfs-usb-gadget-midi | 14 +-
> .../ABI/testing/configfs-usb-gadget-printer | 6 +-
> .../testing/configfs-usb-gadget-sourcesink | 18 +-
> .../ABI/testing/configfs-usb-gadget-subset | 10 +-
> .../ABI/testing/configfs-usb-gadget-uac2 | 14 +-
> .../ABI/testing/configfs-usb-gadget-uvc | 2 +-
> .../ABI/testing/debugfs-cec-error-inj | 2 +-
> .../ABI/testing/debugfs-driver-habanalabs | 12 +-
> .../ABI/testing/debugfs-pfo-nx-crypto | 28 +--
> Documentation/ABI/testing/debugfs-pktcdvd | 2 +-
> .../ABI/testing/debugfs-turris-mox-rwtm | 10 +-
> Documentation/ABI/testing/debugfs-wilco-ec | 21 +-
> Documentation/ABI/testing/dell-smbios-wmi | 32 +--
> Documentation/ABI/testing/gpio-cdev | 13 +-
> Documentation/ABI/testing/procfs-diskstats | 6 +-
> Documentation/ABI/testing/procfs-smaps_rollup | 48 ++--
> Documentation/ABI/testing/pstore | 19 +-
> Documentation/ABI/testing/sysfs-block-rnbd | 4 +-
For rnbd change looks good to me, thanks!
Acked-by: Jack Wang <jinpu.wang at cloud.ionos.com> #rnbd
> index 171127294674..0b4ab9e4b8f4 100644
> --- a/Documentation/ABI/testing/sysfs-bus-thunderbolt
> +++ b/Documentation/ABI/testing/sysfs-bus-thunderbolt
> @@ -193,10 +193,11 @@ Description: When new NVM image is written to the non-active NVM
> verification fails an error code is returned instead.
>
> This file will accept writing values "1" or "2"
> +
> - Writing "1" will flush the image to the storage
> - area and authenticate the image in one action.
> + area and authenticate the image in one action.
> - Writing "2" will run some basic validation on the image
> - and flush it to the storage area.
> + and flush it to the storage area.
>
> When read holds status of the last authentication
> operation if an error occurred during the process. This
> @@ -213,9 +214,11 @@ Description: This contains name of the property directory the XDomain
> question. Following directories are already reserved by
> the Apple XDomain specification:
>
> - network: IP/ethernet over Thunderbolt
> - targetdm: Target disk mode protocol over Thunderbolt
> - extdisp: External display mode protocol over Thunderbolt
> + ======== ===============================================
> + network IP/ethernet over Thunderbolt
> + targetdm Target disk mode protocol over Thunderbolt
> + extdisp External display mode protocol over Thunderbolt
> + ======== ===============================================
>
> What: /sys/bus/thunderbolt/devices/<xdomain>.<service>/modalias
> Date: Jan 2018
> @@ -293,7 +296,8 @@ Description: For supported devices, automatically authenticate the new Thunderbo
> image when the device is disconnected from the host system.
>
> This file will accept writing values "1" or "2"
> +
> - Writing "1" will flush the image to the storage
> - area and prepare the device for authentication on disconnect.
> + area and prepare the device for authentication on disconnect.
> - Writing "2" will run some basic validation on the image
> - and flush it to the storage area.
> + and flush it to the storage area.
> diff --git a/Documentation/ABI/testing/sysfs-bus-usb b/Documentation/ABI/testing/sysfs-bus-usb
> index e449b8374f6a..bf2c1968525f 100644
> --- a/Documentation/ABI/testing/sysfs-bus-usb
> +++ b/Documentation/ABI/testing/sysfs-bus-usb
> @@ -9,6 +9,7 @@ Description:
> by writing INTERFACE to /sys/bus/usb/drivers_probe
> This allows to avoid side-effects with drivers
> that need multiple interfaces.
> +
> A deauthorized interface cannot be probed or claimed.
>
> What: /sys/bus/usb/devices/usbX/interface_authorized_default
> @@ -216,6 +217,7 @@ Description:
> - Bit 0 of this field selects the "old" enumeration scheme,
> as it is considerably faster (it only causes one USB reset
> instead of 2).
> +
> The old enumeration scheme can also be selected globally
> using /sys/module/usbcore/parameters/old_scheme_first, but
> it is often not desirable as the new scheme was introduced to
> diff --git a/Documentation/ABI/testing/sysfs-class-backlight-driver-lm3533 b/Documentation/ABI/testing/sysfs-class-backlight-driver-lm3533
> index c0e0a9ae7b3d..8251e78abc49 100644
> --- a/Documentation/ABI/testing/sysfs-class-backlight-driver-lm3533
> +++ b/Documentation/ABI/testing/sysfs-class-backlight-driver-lm3533
> @@ -6,8 +6,10 @@ Description:
> Get the ALS output channel used as input in
> ALS-current-control mode (0, 1), where:
>
> - 0 - out_current0 (backlight 0)
> - 1 - out_current1 (backlight 1)
> + == ==========================
> + 0 out_current0 (backlight 0)
> + 1 out_current1 (backlight 1)
> + == ==========================
>
> What: /sys/class/backlight/<backlight>/als_en
> Date: May 2012
> @@ -30,8 +32,10 @@ Contact: Johan Hovold <jhovold at gmail.com>
> Description:
> Set the brightness-mapping mode (0, 1), where:
>
> - 0 - exponential mode
> - 1 - linear mode
> + == ================
> + 0 exponential mode
> + 1 linear mode
> + == ================
>
> What: /sys/class/backlight/<backlight>/pwm
> Date: April 2012
> @@ -40,9 +44,11 @@ Contact: Johan Hovold <jhovold at gmail.com>
> Description:
> Set the PWM-input control mask (5 bits), where:
>
> - bit 5 - PWM-input enabled in Zone 4
> - bit 4 - PWM-input enabled in Zone 3
> - bit 3 - PWM-input enabled in Zone 2
> - bit 2 - PWM-input enabled in Zone 1
> - bit 1 - PWM-input enabled in Zone 0
> - bit 0 - PWM-input enabled
> + ===== ===========================
> + bit 5 PWM-input enabled in Zone 4
> + bit 4 PWM-input enabled in Zone 3
> + bit 3 PWM-input enabled in Zone 2
> + bit 2 PWM-input enabled in Zone 1
> + bit 1 PWM-input enabled in Zone 0
> + bit 0 PWM-input enabled
> + ===== ===========================
> diff --git a/Documentation/ABI/testing/sysfs-class-bdi b/Documentation/ABI/testing/sysfs-class-bdi
> index d773d5697cf5..5402bd74ba43 100644
> --- a/Documentation/ABI/testing/sysfs-class-bdi
> +++ b/Documentation/ABI/testing/sysfs-class-bdi
> @@ -24,7 +24,6 @@ default
> filesystems which do not provide their own BDI.
>
> Files under /sys/class/bdi/<bdi>/
> ----------------------------------
>
> read_ahead_kb (read-write)
>
> diff --git a/Documentation/ABI/testing/sysfs-class-chromeos b/Documentation/ABI/testing/sysfs-class-chromeos
> index 5819699d66ec..74ece942722e 100644
> --- a/Documentation/ABI/testing/sysfs-class-chromeos
> +++ b/Documentation/ABI/testing/sysfs-class-chromeos
> @@ -17,13 +17,14 @@ Date: August 2015
> KernelVersion: 4.2
> Description:
> Tell the EC to reboot in various ways. Options are:
> - "cancel": Cancel a pending reboot.
> - "ro": Jump to RO without rebooting.
> - "rw": Jump to RW without rebooting.
> - "cold": Cold reboot.
> - "disable-jump": Disable jump until next reboot.
> - "hibernate": Hibernate the EC.
> - "at-shutdown": Reboot after an AP shutdown.
> +
> + - "cancel": Cancel a pending reboot.
> + - "ro": Jump to RO without rebooting.
> + - "rw": Jump to RW without rebooting.
> + - "cold": Cold reboot.
> + - "disable-jump": Disable jump until next reboot.
> + - "hibernate": Hibernate the EC.
> + - "at-shutdown": Reboot after an AP shutdown.
>
> What: /sys/class/chromeos/<ec-device-name>/version
> Date: August 2015
> diff --git a/Documentation/ABI/testing/sysfs-class-cxl b/Documentation/ABI/testing/sysfs-class-cxl
> index a6f51a104c44..818f55970efb 100644
> --- a/Documentation/ABI/testing/sysfs-class-cxl
> +++ b/Documentation/ABI/testing/sysfs-class-cxl
> @@ -217,6 +217,7 @@ Description: read/write
> card. A power cycle is required to load the image.
> "none" could be useful for debugging because the trace arrays
> are preserved.
> +
> "user" and "factory" means PERST will cause either the user or
> user or factory image to be loaded.
> Default is to reload on PERST whichever image the card has
> @@ -240,8 +241,11 @@ Contact: linuxppc-dev at lists.ozlabs.org
> Description: read/write
> Trust that when an image is reloaded via PERST, it will not
> have changed.
> - 0 = don't trust, the image may be different (default)
> - 1 = trust that the image will not change.
> +
> + == =================================================
> + 0 don't trust, the image may be different (default)
> + 1 trust that the image will not change.
> + == =================================================
> Users: https://github.com/ibm-capi/libcxl
>
> What: /sys/class/cxl/<card>/psl_timebase_synced
> diff --git a/Documentation/ABI/testing/sysfs-class-devlink b/Documentation/ABI/testing/sysfs-class-devlink
> index 64791b65c9a3..b662f747c83e 100644
> --- a/Documentation/ABI/testing/sysfs-class-devlink
> +++ b/Documentation/ABI/testing/sysfs-class-devlink
> @@ -18,9 +18,9 @@ Description:
>
> This will be one of the following strings:
>
> - 'consumer unbind'
> - 'supplier unbind'
> - 'never'
> + - 'consumer unbind'
> + - 'supplier unbind'
> + - 'never'
>
> 'consumer unbind' means the device link will be removed when
> the consumer's driver is unbound from the consumer device.
> @@ -49,8 +49,10 @@ Description:
>
> This will be one of the following strings:
>
> - '0' - Does not affect runtime power management
> - '1' - Affects runtime power management
> + === ========================================
> + '0' Does not affect runtime power management
> + '1' Affects runtime power management
> + === ========================================
>
> What: /sys/class/devlink/.../status
> Date: May 2020
> @@ -68,13 +70,13 @@ Description:
>
> This will be one of the following strings:
>
> - 'not tracked'
> - 'dormant'
> - 'available'
> - 'consumer probing'
> - 'active'
> - 'supplier unbinding'
> - 'unknown'
> + - 'not tracked'
> + - 'dormant'
> + - 'available'
> + - 'consumer probing'
> + - 'active'
> + - 'supplier unbinding'
> + - 'unknown'
>
> 'not tracked' means this device link does not track the status
> and has no impact on the binding, unbinding and syncing the
> @@ -114,8 +116,10 @@ Description:
>
> This will be one of the following strings:
>
> + === ================================
> '0'
> - '1' - Affects runtime power management
> + '1' Affects runtime power management
> + === ================================
>
> '0' means the device link can affect other device behaviors
> like binding/unbinding, suspend/resume, runtime power
> diff --git a/Documentation/ABI/testing/sysfs-class-extcon b/Documentation/ABI/testing/sysfs-class-extcon
> index 57a726232912..fde0fecd5de9 100644
> --- a/Documentation/ABI/testing/sysfs-class-extcon
> +++ b/Documentation/ABI/testing/sysfs-class-extcon
> @@ -39,19 +39,22 @@ Description:
> callback.
>
> If the default callback for showing function is used, the
> - format is like this:
> - # cat state
> - USB_OTG=1
> - HDMI=0
> - TA=1
> - EAR_JACK=0
> - #
> + format is like this::
> +
> + # cat state
> + USB_OTG=1
> + HDMI=0
> + TA=1
> + EAR_JACK=0
> + #
> +
> In this example, the extcon device has USB_OTG and TA
> cables attached and HDMI and EAR_JACK cables detached.
>
> In order to update the state of an extcon device, enter a hex
> - state number starting with 0x:
> - # echo 0xHEX > state
> + state number starting with 0x::
> +
> + # echo 0xHEX > state
>
> This updates the whole state of the extcon device.
> Inputs of all the methods are required to meet the
> @@ -84,12 +87,13 @@ Contact: MyungJoo Ham <myungjoo.ham at samsung.com>
> Description:
> Shows the relations of mutually exclusiveness. For example,
> if the mutually_exclusive array of extcon device is
> - {0x3, 0x5, 0xC, 0x0}, then the output is:
> - # ls mutually_exclusive/
> - 0x3
> - 0x5
> - 0xc
> - #
> + {0x3, 0x5, 0xC, 0x0}, then the output is::
> +
> + # ls mutually_exclusive/
> + 0x3
> + 0x5
> + 0xc
> + #
>
> Note that mutually_exclusive is a sub-directory of the extcon
> device and the file names under the mutually_exclusive
> diff --git a/Documentation/ABI/testing/sysfs-class-fpga-manager b/Documentation/ABI/testing/sysfs-class-fpga-manager
> index 5284fa33d4c5..d78689c357a5 100644
> --- a/Documentation/ABI/testing/sysfs-class-fpga-manager
> +++ b/Documentation/ABI/testing/sysfs-class-fpga-manager
> @@ -28,8 +28,7 @@ Description: Read fpga manager state as a string.
> * firmware request = firmware class request in progress
> * firmware request error = firmware request failed
> * write init = preparing FPGA for programming
> - * write init error = Error while preparing FPGA for
> - programming
> + * write init error = Error while preparing FPGA for programming
> * write = FPGA ready to receive image data
> * write error = Error while programming
> * write complete = Doing post programming steps
> @@ -47,7 +46,7 @@ Description: Read fpga manager status as a string.
> programming errors to userspace. This is a list of strings for
> the supported status.
>
> - * reconfig operation error - invalid operations detected by
> + * reconfig operation error - invalid operations detected by
> reconfiguration hardware.
> e.g. start reconfiguration
> with errors not cleared
> diff --git a/Documentation/ABI/testing/sysfs-class-gnss b/Documentation/ABI/testing/sysfs-class-gnss
> index 2467b6900eae..c8553d972edd 100644
> --- a/Documentation/ABI/testing/sysfs-class-gnss
> +++ b/Documentation/ABI/testing/sysfs-class-gnss
> @@ -6,9 +6,11 @@ Description:
> The GNSS receiver type. The currently identified types reflect
> the protocol(s) supported by the receiver:
>
> + ====== ===========
> "NMEA" NMEA 0183
> "SiRF" SiRF Binary
> "UBX" UBX
> + ====== ===========
>
> Note that also non-"NMEA" type receivers typically support a
> subset of NMEA 0183 with vendor extensions (e.g. to allow
> diff --git a/Documentation/ABI/testing/sysfs-class-led b/Documentation/ABI/testing/sysfs-class-led
> index 65e040978f73..0ed5c2629c6f 100644
> --- a/Documentation/ABI/testing/sysfs-class-led
> +++ b/Documentation/ABI/testing/sysfs-class-led
> @@ -47,6 +47,7 @@ Contact: Richard Purdie <rpurdie at rpsys.net>
> Description:
> Set the trigger for this LED. A trigger is a kernel based source
> of LED events.
> +
> You can change triggers in a similar manner to the way an IO
> scheduler is chosen. Trigger specific parameters can appear in
> /sys/class/leds/<led> once a given trigger is selected. For
> diff --git a/Documentation/ABI/testing/sysfs-class-led-driver-el15203000 b/Documentation/ABI/testing/sysfs-class-led-driver-el15203000
> index 69befe947d7e..da546e86deb5 100644
> --- a/Documentation/ABI/testing/sysfs-class-led-driver-el15203000
> +++ b/Documentation/ABI/testing/sysfs-class-led-driver-el15203000
> @@ -27,23 +27,23 @@ Description:
>
> ^
> |
> - 0 On -|----+ +----+ +---
> + 0 On -|----+ +----+ +---
> | | | | |
> Off-| +-------------------+ +-------------------+
> |
> - 1 On -| +----+ +----+
> + 1 On -| +----+ +----+
> | | | | |
> Off |----+ +-------------------+ +------------------
> |
> - 2 On -| +----+ +----+
> + 2 On -| +----+ +----+
> | | | | |
> Off-|---------+ +-------------------+ +-------------
> |
> - 3 On -| +----+ +----+
> + 3 On -| +----+ +----+
> | | | | |
> Off-|--------------+ +-------------------+ +--------
> |
> - 4 On -| +----+ +----+
> + 4 On -| +----+ +----+
> | | | | |
> Off-|-------------------+ +-------------------+ +---
> |
> @@ -55,23 +55,23 @@ Description:
>
> ^
> |
> - 0 On -| +-------------------+ +-------------------+
> + 0 On -| +-------------------+ +-------------------+
> | | | | |
> Off-|----+ +----+ +---
> |
> - 1 On -|----+ +-------------------+ +------------------
> + 1 On -|----+ +-------------------+ +------------------
> | | | | |
> Off | +----+ +----+
> |
> - 2 On -|---------+ +-------------------+ +-------------
> + 2 On -|---------+ +-------------------+ +-------------
> | | | | |
> Off-| +----+ +----+
> |
> - 3 On -|--------------+ +-------------------+ +--------
> + 3 On -|--------------+ +-------------------+ +--------
> | | | | |
> Off-| +----+ +----+
> |
> - 4 On -|-------------------+ +-------------------+ +---
> + 4 On -|-------------------+ +-------------------+ +---
> | | | | |
> Off-| +----+ +----+
> |
> @@ -83,23 +83,23 @@ Description:
>
> ^
> |
> - 0 On -|----+ +--------
> + 0 On -|----+ +--------
> | | |
> Off-| +---------------------------------------+
> |
> - 1 On -| +----+ +----+
> + 1 On -| +----+ +----+
> | | | | |
> Off |----+ +-----------------------------+ +--------
> |
> - 2 On -| +----+ +----+
> + 2 On -| +----+ +----+
> | | | | |
> Off-|---------+ +-------------------+ +-------------
> |
> - 3 On -| +----+ +----+
> + 3 On -| +----+ +----+
> | | | | |
> Off-|--------------+ +---------+ +------------------
> |
> - 4 On -| +---------+
> + 4 On -| +---------+
> | | |
> Off-|-------------------+ +-----------------------
> |
> diff --git a/Documentation/ABI/testing/sysfs-class-led-driver-lm3533 b/Documentation/ABI/testing/sysfs-class-led-driver-lm3533
> index e4c89b261546..e38a835d0a85 100644
> --- a/Documentation/ABI/testing/sysfs-class-led-driver-lm3533
> +++ b/Documentation/ABI/testing/sysfs-class-led-driver-lm3533
> @@ -6,8 +6,10 @@ Description:
> Set the ALS output channel to use as input in
> ALS-current-control mode (1, 2), where:
>
> - 1 - out_current1
> - 2 - out_current2
> + == ============
> + 1 out_current1
> + 2 out_current2
> + == ============
>
> What: /sys/class/leds/<led>/als_en
> Date: May 2012
> @@ -24,14 +26,16 @@ Contact: Johan Hovold <jhovold at gmail.com>
> Description:
> Set the pattern generator fall and rise times (0..7), where:
>
> - 0 - 2048 us
> - 1 - 262 ms
> - 2 - 524 ms
> - 3 - 1.049 s
> - 4 - 2.097 s
> - 5 - 4.194 s
> - 6 - 8.389 s
> - 7 - 16.78 s
> + == =======
> + 0 2048 us
> + 1 262 ms
> + 2 524 ms
> + 3 1.049 s
> + 4 2.097 s
> + 5 4.194 s
> + 6 8.389 s
> + 7 16.78 s
> + == =======
>
> What: /sys/class/leds/<led>/id
> Date: April 2012
> @@ -47,8 +51,10 @@ Contact: Johan Hovold <jhovold at gmail.com>
> Description:
> Set the brightness-mapping mode (0, 1), where:
>
> - 0 - exponential mode
> - 1 - linear mode
> + == ================
> + 0 exponential mode
> + 1 linear mode
> + == ================
>
> What: /sys/class/leds/<led>/pwm
> Date: April 2012
> @@ -57,9 +63,11 @@ Contact: Johan Hovold <jhovold at gmail.com>
> Description:
> Set the PWM-input control mask (5 bits), where:
>
> - bit 5 - PWM-input enabled in Zone 4
> - bit 4 - PWM-input enabled in Zone 3
> - bit 3 - PWM-input enabled in Zone 2
> - bit 2 - PWM-input enabled in Zone 1
> - bit 1 - PWM-input enabled in Zone 0
> - bit 0 - PWM-input enabled
> + ===== ===========================
> + bit 5 PWM-input enabled in Zone 4
> + bit 4 PWM-input enabled in Zone 3
> + bit 3 PWM-input enabled in Zone 2
> + bit 2 PWM-input enabled in Zone 1
> + bit 1 PWM-input enabled in Zone 0
> + bit 0 PWM-input enabled
> + ===== ===========================
> diff --git a/Documentation/ABI/testing/sysfs-class-led-flash b/Documentation/ABI/testing/sysfs-class-led-flash
> index 220a0270b47b..11e5677c3672 100644
> --- a/Documentation/ABI/testing/sysfs-class-led-flash
> +++ b/Documentation/ABI/testing/sysfs-class-led-flash
> @@ -55,26 +55,35 @@ Description: read only
> Flash faults are re-read after strobing the flash. Possible
> flash faults:
>
> - * led-over-voltage - flash controller voltage to the flash LED
> + * led-over-voltage
> + flash controller voltage to the flash LED
> has exceeded the limit specific to the flash controller
> - * flash-timeout-exceeded - the flash strobe was still on when
> + * flash-timeout-exceeded
> + the flash strobe was still on when
> the timeout set by the user has expired; not all flash
> controllers may set this in all such conditions
> - * controller-over-temperature - the flash controller has
> + * controller-over-temperature
> + the flash controller has
> overheated
> - * controller-short-circuit - the short circuit protection
> + * controller-short-circuit
> + the short circuit protection
> of the flash controller has been triggered
> - * led-power-supply-over-current - current in the LED power
> + * led-power-supply-over-current
> + current in the LED power
> supply has exceeded the limit specific to the flash
> controller
> - * indicator-led-fault - the flash controller has detected
> + * indicator-led-fault
> + the flash controller has detected
> a short or open circuit condition on the indicator LED
> - * led-under-voltage - flash controller voltage to the flash
> + * led-under-voltage
> + flash controller voltage to the flash
> LED has been below the minimum limit specific to
> the flash
> - * controller-under-voltage - the input voltage of the flash
> + * controller-under-voltage
> + the input voltage of the flash
> controller is below the limit under which strobing the
> flash at full current will not be possible;
> the condition persists until this flag is no longer set
> - * led-over-temperature - the temperature of the LED has exceeded
> + * led-over-temperature
> + the temperature of the LED has exceeded
> its allowed upper limit
> diff --git a/Documentation/ABI/testing/sysfs-class-led-trigger-netdev b/Documentation/ABI/testing/sysfs-class-led-trigger-netdev
> index 451af6d6768c..646540950e38 100644
> --- a/Documentation/ABI/testing/sysfs-class-led-trigger-netdev
> +++ b/Documentation/ABI/testing/sysfs-class-led-trigger-netdev
> @@ -19,18 +19,23 @@ KernelVersion: 4.16
> Contact: linux-leds at vger.kernel.org
> Description:
> Signal the link state of the named network device.
> +
> If set to 0 (default), the LED's normal state is off.
> +
> If set to 1, the LED's normal state reflects the link state
> of the named network device.
> Setting this value also immediately changes the LED state.
>
> +
> What: /sys/class/leds/<led>/tx
> Date: Dec 2017
> KernelVersion: 4.16
> Contact: linux-leds at vger.kernel.org
> Description:
> Signal transmission of data on the named network device.
> +
> If set to 0 (default), the LED will not blink on transmission.
> +
> If set to 1, the LED will blink for the milliseconds specified
> in interval to signal transmission.
>
> @@ -40,6 +45,8 @@ KernelVersion: 4.16
> Contact: linux-leds at vger.kernel.org
> Description:
> Signal reception of data on the named network device.
> +
> If set to 0 (default), the LED will not blink on reception.
> +
> If set to 1, the LED will blink for the milliseconds specified
> in interval to signal reception.
> diff --git a/Documentation/ABI/testing/sysfs-class-led-trigger-usbport b/Documentation/ABI/testing/sysfs-class-led-trigger-usbport
> index f440e690daef..eb81152b8348 100644
> --- a/Documentation/ABI/testing/sysfs-class-led-trigger-usbport
> +++ b/Documentation/ABI/testing/sysfs-class-led-trigger-usbport
> @@ -8,5 +8,6 @@ Description:
> selected for the USB port trigger. Selecting ports makes trigger
> observing them for any connected devices and lighting on LED if
> there are any.
> +
> Echoing "1" value selects USB port. Echoing "0" unselects it.
> Current state can be also read.
> diff --git a/Documentation/ABI/testing/sysfs-class-leds-gt683r b/Documentation/ABI/testing/sysfs-class-leds-gt683r
> index 6adab27f646e..b57ffb26e722 100644
> --- a/Documentation/ABI/testing/sysfs-class-leds-gt683r
> +++ b/Documentation/ABI/testing/sysfs-class-leds-gt683r
> @@ -7,9 +7,11 @@ Description:
> of one LED will update the mode of its two sibling devices as
> well. Possible values are:
>
> - 0 - normal
> - 1 - audio
> - 2 - breathing
> + == =========
> + 0 normal
> + 1 audio
> + 2 breathing
> + == =========
>
> Normal: LEDs are fully on when enabled
> Audio: LEDs brightness depends on sound level
> diff --git a/Documentation/ABI/testing/sysfs-class-net b/Documentation/ABI/testing/sysfs-class-net
> index 3b404577f380..7670012ae9b6 100644
> --- a/Documentation/ABI/testing/sysfs-class-net
> +++ b/Documentation/ABI/testing/sysfs-class-net
> @@ -4,10 +4,13 @@ KernelVersion: 3.17
> Contact: netdev at vger.kernel.org
> Description:
> Indicates the name assignment type. Possible values are:
> - 1: enumerated by the kernel, possibly in an unpredictable way
> - 2: predictably named by the kernel
> - 3: named by userspace
> - 4: renamed
> +
> + == ==========================================================
> + 1 enumerated by the kernel, possibly in an unpredictable way
> + 2 predictably named by the kernel
> + 3 named by userspace
> + 4 renamed
> + == ==========================================================
>
> What: /sys/class/net/<iface>/addr_assign_type
> Date: July 2010
> @@ -15,10 +18,13 @@ KernelVersion: 3.2
> Contact: netdev at vger.kernel.org
> Description:
> Indicates the address assignment type. Possible values are:
> - 0: permanent address
> - 1: randomly generated
> - 2: stolen from another device
> - 3: set using dev_set_mac_address
> +
> + == =============================
> + 0 permanent address
> + 1 randomly generated
> + 2 stolen from another device
> + 3 set using dev_set_mac_address
> + == =============================
>
> What: /sys/class/net/<iface>/addr_len
> Date: April 2005
> @@ -51,9 +57,12 @@ Description:
> Default value 0 does not forward any link local frames.
>
> Restricted bits:
> - 0: 01-80-C2-00-00-00 Bridge Group Address used for STP
> - 1: 01-80-C2-00-00-01 (MAC Control) 802.3 used for MAC PAUSE
> - 2: 01-80-C2-00-00-02 (Link Aggregation) 802.3ad
> +
> + == ========================================================
> + 0 01-80-C2-00-00-00 Bridge Group Address used for STP
> + 1 01-80-C2-00-00-01 (MAC Control) 802.3 used for MAC PAUSE
> + 2 01-80-C2-00-00-02 (Link Aggregation) 802.3ad
> + == ========================================================
>
> Any values not setting these bits can be used. Take special
> care when forwarding control frames e.g. 802.1X-PAE or LLDP.
> @@ -74,8 +83,11 @@ Contact: netdev at vger.kernel.org
> Description:
> Indicates the current physical link state of the interface.
> Posssible values are:
> - 0: physical link is down
> - 1: physical link is up
> +
> + == =====================
> + 0 physical link is down
> + 1 physical link is up
> + == =====================
>
> Note: some special devices, e.g: bonding and team drivers will
> allow this attribute to be written to force a link state for
> @@ -131,8 +143,11 @@ Contact: netdev at vger.kernel.org
> Description:
> Indicates whether the interface is under test. Possible
> values are:
> - 0: interface is not being tested
> - 1: interface is being tested
> +
> + == =============================
> + 0 interface is not being tested
> + 1 interface is being tested
> + == =============================
>
> When an interface is under test, it cannot be expected
> to pass packets as normal.
> @@ -144,8 +159,11 @@ Contact: netdev at vger.kernel.org
> Description:
> Indicates the interface latest or current duplex value. Possible
> values are:
> - half: half duplex
> - full: full duplex
> +
> + ==== ===========
> + half half duplex
> + full full duplex
> + ==== ===========
>
> Note: This attribute is only valid for interfaces that implement
> the ethtool get_link_ksettings method (mostly Ethernet).
> @@ -196,8 +214,11 @@ Description:
> Indicates the interface link mode, as a decimal number. This
> attribute should be used in conjunction with 'dormant' attribute
> to determine the interface usability. Possible values:
> - 0: default link mode
> - 1: dormant link mode
> +
> + == =================
> + 0 default link mode
> + 1 dormant link mode
> + == =================
>
> What: /sys/class/net/<iface>/mtu
> Date: April 2005
> @@ -226,7 +247,9 @@ KernelVersion: 2.6.17
> Contact: netdev at vger.kernel.org
> Description:
> Indicates the interface RFC2863 operational state as a string.
> +
> Possible values are:
> +
> "unknown", "notpresent", "down", "lowerlayerdown", "testing",
> "dormant", "up".
>
> diff --git a/Documentation/ABI/testing/sysfs-class-net-cdc_ncm b/Documentation/ABI/testing/sysfs-class-net-cdc_ncm
> index f7be0e88b139..06416d0e163d 100644
> --- a/Documentation/ABI/testing/sysfs-class-net-cdc_ncm
> +++ b/Documentation/ABI/testing/sysfs-class-net-cdc_ncm
> @@ -91,9 +91,9 @@ Date: May 2014
> KernelVersion: 3.16
> Contact: Bjørn Mork <bjorn at mork.no>
> Description:
> - Bit 0: 16-bit NTB supported (set to 1)
> - Bit 1: 32-bit NTB supported
> - Bits 2 – 15: reserved (reset to zero; must be ignored by host)
> + - Bit 0: 16-bit NTB supported (set to 1)
> + - Bit 1: 32-bit NTB supported
> + - Bits 2 – 15: reserved (reset to zero; must be ignored by host)
>
> What: /sys/class/net/<iface>/cdc_ncm/dwNtbInMaxSize
> Date: May 2014
> diff --git a/Documentation/ABI/testing/sysfs-class-net-phydev b/Documentation/ABI/testing/sysfs-class-net-phydev
> index 206cbf538b59..40ced0ea4316 100644
> --- a/Documentation/ABI/testing/sysfs-class-net-phydev
> +++ b/Documentation/ABI/testing/sysfs-class-net-phydev
> @@ -35,7 +35,9 @@ Description:
> Ethernet driver during bus enumeration, encoded in string.
> This interface mode is used to configure the Ethernet MAC with the
> appropriate mode for its data lines to the PHY hardware.
> +
> Possible values are:
> +
> <empty> (not available), mii, gmii, sgmii, tbi, rev-mii,
> rmii, rgmii, rgmii-id, rgmii-rxid, rgmii-txid, rtbi, smii
> xgmii, moca, qsgmii, trgmii, 1000base-x, 2500base-x, rxaui,
> diff --git a/Documentation/ABI/testing/sysfs-class-pktcdvd b/Documentation/ABI/testing/sysfs-class-pktcdvd
> index dde4f26d0780..ba1ce626591d 100644
> --- a/Documentation/ABI/testing/sysfs-class-pktcdvd
> +++ b/Documentation/ABI/testing/sysfs-class-pktcdvd
> @@ -11,15 +11,17 @@ KernelVersion: 2.6.20
> Contact: Thomas Maier <balagi at justmail.de>
> Description:
>
> - add: (WO) Write a block device id (major:minor) to
> + ========== ==============================================
> + add (WO) Write a block device id (major:minor) to
> create a new pktcdvd device and map it to the
> block device.
>
> - remove: (WO) Write the pktcdvd device id (major:minor)
> + remove (WO) Write the pktcdvd device id (major:minor)
> to remove the pktcdvd device.
>
> - device_map: (RO) Shows the device mapping in format:
> + device_map (RO) Shows the device mapping in format:
> pktcdvd[0-7] <pktdevid> <blkdevid>
> + ========== ==============================================
>
>
> What: /sys/class/pktcdvd/pktcdvd[0-7]/dev
> @@ -65,29 +67,31 @@ Date: Oct. 2006
> KernelVersion: 2.6.20
> Contact: Thomas Maier <balagi at justmail.de>
> Description:
> - size: (RO) Contains the size of the bio write queue.
> + ============== ================================================
> + size (RO) Contains the size of the bio write queue.
>
> - congestion_off: (RW) If bio write queue size is below this mark,
> + congestion_off (RW) If bio write queue size is below this mark,
> accept new bio requests from the block layer.
>
> - congestion_on: (RW) If bio write queue size is higher as this
> + congestion_on (RW) If bio write queue size is higher as this
> mark, do no longer accept bio write requests
> from the block layer and wait till the pktcdvd
> device has processed enough bio's so that bio
> write queue size is below congestion off mark.
> A value of <= 0 disables congestion control.
> + ============== ================================================
>
>
> Example:
> --------
> -To use the pktcdvd sysfs interface directly, you can do:
> +To use the pktcdvd sysfs interface directly, you can do::
>
> -# create a new pktcdvd device mapped to /dev/hdc
> -echo "22:0" >/sys/class/pktcdvd/add
> -cat /sys/class/pktcdvd/device_map
> -# assuming device pktcdvd0 was created, look at stat's
> -cat /sys/class/pktcdvd/pktcdvd0/stat/kb_written
> -# print the device id of the mapped block device
> -fgrep pktcdvd0 /sys/class/pktcdvd/device_map
> -# remove device, using pktcdvd0 device id 253:0
> -echo "253:0" >/sys/class/pktcdvd/remove
> + # create a new pktcdvd device mapped to /dev/hdc
> + echo "22:0" >/sys/class/pktcdvd/add
> + cat /sys/class/pktcdvd/device_map
> + # assuming device pktcdvd0 was created, look at stat's
> + cat /sys/class/pktcdvd/pktcdvd0/stat/kb_written
> + # print the device id of the mapped block device
> + fgrep pktcdvd0 /sys/class/pktcdvd/device_map
> + # remove device, using pktcdvd0 device id 253:0
> + echo "253:0" >/sys/class/pktcdvd/remove
> diff --git a/Documentation/ABI/testing/sysfs-class-power b/Documentation/ABI/testing/sysfs-class-power
> index d4319a04c302..d68ad528a8e5 100644
> --- a/Documentation/ABI/testing/sysfs-class-power
> +++ b/Documentation/ABI/testing/sysfs-class-power
> @@ -43,7 +43,9 @@ Date: May 2007
> Contact: linux-pm at vger.kernel.org
> Description:
> Fine grain representation of battery capacity.
> +
> Access: Read
> +
> Valid values: 0 - 100 (percent)
>
> What: /sys/class/power_supply/<supply_name>/capacity_alert_max
> @@ -58,6 +60,7 @@ Description:
> low).
>
> Access: Read, Write
> +
> Valid values: 0 - 100 (percent)
>
> What: /sys/class/power_supply/<supply_name>/capacity_alert_min
> @@ -88,6 +91,7 @@ Description:
> completely useless.
>
> Access: Read
> +
> Valid values: 0 - 100 (percent)
>
> What: /sys/class/power_supply/<supply_name>/capacity_level
> @@ -111,6 +115,7 @@ Description:
> which they average readings to smooth out the reported value.
>
> Access: Read
> +
> Valid values: Represented in microamps. Negative values are used
> for discharging batteries, positive values for charging batteries.
>
> @@ -131,6 +136,7 @@ Description:
> This value is not averaged/smoothed.
>
> Access: Read
> +
> Valid values: Represented in microamps. Negative values are used
> for discharging batteries, positive values for charging batteries.
>
> @@ -383,7 +389,7 @@ Description:
>
> **USB Properties**
>
> -What: /sys/class/power_supply/<supply_name>/current_avg
> +What: /sys/class/power_supply/<supply_name>/current_avg
> Date: May 2007
> Contact: linux-pm at vger.kernel.org
> Description:
> @@ -449,6 +455,7 @@ Description:
> solved using power limit use input_voltage_limit.
>
> Access: Read, Write
> +
> Valid values: Represented in microvolts
>
> What: /sys/class/power_supply/<supply_name>/input_power_limit
> @@ -462,6 +469,7 @@ Description:
> limit only for problems that can be solved using power limit.
>
> Access: Read, Write
> +
> Valid values: Represented in microwatts
>
> What: /sys/class/power_supply/<supply_name>/online,
> @@ -747,6 +755,7 @@ Description:
> manufactured.
>
> Access: Read
> +
> Valid values: Reported as integer
>
> What: /sys/class/power_supply/<supply_name>/manufacture_month
> @@ -756,6 +765,7 @@ Description:
> Reports the month when the device has been manufactured.
>
> Access: Read
> +
> Valid values: 1-12
>
> What: /sys/class/power_supply/<supply_name>/manufacture_day
> diff --git a/Documentation/ABI/testing/sysfs-class-power-mp2629 b/Documentation/ABI/testing/sysfs-class-power-mp2629
> index 327a07e22805..914d67caac0d 100644
> --- a/Documentation/ABI/testing/sysfs-class-power-mp2629
> +++ b/Documentation/ABI/testing/sysfs-class-power-mp2629
> @@ -5,4 +5,5 @@ Description:
> Represents a battery impedance compensation to accelerate charging.
>
> Access: Read, Write
> +
> Valid values: Represented in milli-ohms. Valid range is [0, 140].
> diff --git a/Documentation/ABI/testing/sysfs-class-power-twl4030 b/Documentation/ABI/testing/sysfs-class-power-twl4030
> index 7ac36dba87bc..b52f7023f8ba 100644
> --- a/Documentation/ABI/testing/sysfs-class-power-twl4030
> +++ b/Documentation/ABI/testing/sysfs-class-power-twl4030
> @@ -6,9 +6,9 @@ Description:
> Possible values are:
>
> ============= ===========================================
> - "auto" draw power as appropriate for detected
> + "auto" draw power as appropriate for detected
> power source and battery status.
> - "off" do not draw any power.
> + "off" do not draw any power.
> "continuous" activate mode described as "linear" in
> TWL data sheets. This uses whatever
> current is available and doesn't switch off
> diff --git a/Documentation/ABI/testing/sysfs-class-rapidio b/Documentation/ABI/testing/sysfs-class-rapidio
> index 8716beeb16c1..19aefb21b639 100644
> --- a/Documentation/ABI/testing/sysfs-class-rapidio
> +++ b/Documentation/ABI/testing/sysfs-class-rapidio
> @@ -6,6 +6,7 @@ Description:
> The /sys/class/rapidio_port subdirectory contains individual
> subdirectories named as "rapidioN" where N = mport ID registered
> with RapidIO subsystem.
> +
> NOTE: An mport ID is not a RapidIO destination ID assigned to a
> given local mport device.
>
> @@ -16,7 +17,9 @@ Contact: Matt Porter <mporter at kernel.crashing.org>,
> Alexandre Bounine <alexandre.bounine at idt.com>
> Description:
> (RO) reports RapidIO common transport system size:
> +
> 0 = small (8-bit destination ID, max. 256 devices),
> +
> 1 = large (16-bit destination ID, max. 65536 devices).
>
> What: /sys/class/rapidio_port/rapidioN/port_destid
> @@ -25,31 +28,32 @@ KernelVersion: v3.15
> Contact: Matt Porter <mporter at kernel.crashing.org>,
> Alexandre Bounine <alexandre.bounine at idt.com>
> Description:
> - (RO) reports RapidIO destination ID assigned to the given
> - RapidIO mport device. If value 0xFFFFFFFF is returned this means
> - that no valid destination ID have been assigned to the mport
> - (yet). Normally, before enumeration/discovery have been executed
> - only fabric enumerating mports have a valid destination ID
> - assigned to them using "hdid=..." rapidio module parameter.
> +
> +(RO) reports RapidIO destination ID assigned to the given
> +RapidIO mport device. If value 0xFFFFFFFF is returned this means
> +that no valid destination ID have been assigned to the mport
> +(yet). Normally, before enumeration/discovery have been executed
> +only fabric enumerating mports have a valid destination ID
> +assigned to them using "hdid=..." rapidio module parameter.
>
> After enumeration or discovery was performed for a given mport device,
> the corresponding subdirectory will also contain subdirectories for each
> child RapidIO device connected to the mport.
>
> The example below shows mport device subdirectory with several child RapidIO
> -devices attached to it.
> +devices attached to it::
>
> -[rio at rapidio ~]$ ls /sys/class/rapidio_port/rapidio0/ -l
> -total 0
> -drwxr-xr-x 3 root root 0 Feb 11 15:10 00:e:0001
> -drwxr-xr-x 3 root root 0 Feb 11 15:10 00:e:0004
> -drwxr-xr-x 3 root root 0 Feb 11 15:10 00:e:0007
> -drwxr-xr-x 3 root root 0 Feb 11 15:10 00:s:0002
> -drwxr-xr-x 3 root root 0 Feb 11 15:10 00:s:0003
> -drwxr-xr-x 3 root root 0 Feb 11 15:10 00:s:0005
> -lrwxrwxrwx 1 root root 0 Feb 11 15:11 device -> ../../../0000:01:00.0
> --r--r--r-- 1 root root 4096 Feb 11 15:11 port_destid
> -drwxr-xr-x 2 root root 0 Feb 11 15:11 power
> -lrwxrwxrwx 1 root root 0 Feb 11 15:04 subsystem -> ../../../../../../class/rapidio_port
> --r--r--r-- 1 root root 4096 Feb 11 15:11 sys_size
> --rw-r--r-- 1 root root 4096 Feb 11 15:04 uevent
> + [rio at rapidio ~]$ ls /sys/class/rapidio_port/rapidio0/ -l
> + total 0
> + drwxr-xr-x 3 root root 0 Feb 11 15:10 00:e:0001
> + drwxr-xr-x 3 root root 0 Feb 11 15:10 00:e:0004
> + drwxr-xr-x 3 root root 0 Feb 11 15:10 00:e:0007
> + drwxr-xr-x 3 root root 0 Feb 11 15:10 00:s:0002
> + drwxr-xr-x 3 root root 0 Feb 11 15:10 00:s:0003
> + drwxr-xr-x 3 root root 0 Feb 11 15:10 00:s:0005
> + lrwxrwxrwx 1 root root 0 Feb 11 15:11 device -> ../../../0000:01:00.0
> + -r--r--r-- 1 root root 4096 Feb 11 15:11 port_destid
> + drwxr-xr-x 2 root root 0 Feb 11 15:11 power
> + lrwxrwxrwx 1 root root 0 Feb 11 15:04 subsystem -> ../../../../../../class/rapidio_port
> + -r--r--r-- 1 root root 4096 Feb 11 15:11 sys_size
> + -rw-r--r-- 1 root root 4096 Feb 11 15:04 uevent
> diff --git a/Documentation/ABI/testing/sysfs-class-regulator b/Documentation/ABI/testing/sysfs-class-regulator
> index bc578bc60628..8516f08806dd 100644
> --- a/Documentation/ABI/testing/sysfs-class-regulator
> +++ b/Documentation/ABI/testing/sysfs-class-regulator
> @@ -35,13 +35,13 @@ Description:
>
> This will be one of the following strings:
>
> - off
> - on
> - error
> - fast
> - normal
> - idle
> - standby
> + - off
> + - on
> + - error
> + - fast
> + - normal
> + - idle
> + - standby
>
> "off" means the regulator is not supplying power to the
> system.
> @@ -74,9 +74,9 @@ Description:
>
> This will be one of the following strings:
>
> - 'voltage'
> - 'current'
> - 'unknown'
> + - 'voltage'
> + - 'current'
> + - 'unknown'
>
> 'voltage' means the regulator output voltage can be controlled
> by software.
> @@ -129,11 +129,11 @@ Description:
>
> The opmode value can be one of the following strings:
>
> - 'fast'
> - 'normal'
> - 'idle'
> - 'standby'
> - 'unknown'
> + - 'fast'
> + - 'normal'
> + - 'idle'
> + - 'standby'
> + - 'unknown'
>
> The modes are described in include/linux/regulator/consumer.h
>
> @@ -360,9 +360,9 @@ Description:
>
> This will be one of the following strings:
>
> - 'enabled'
> - 'disabled'
> - 'unknown'
> + - 'enabled'
> + - 'disabled'
> + - 'unknown'
>
> 'enabled' means the regulator is in bypass mode.
>
> diff --git a/Documentation/ABI/testing/sysfs-class-remoteproc b/Documentation/ABI/testing/sysfs-class-remoteproc
> index 066b9b6f4924..0c9ee55098b8 100644
> --- a/Documentation/ABI/testing/sysfs-class-remoteproc
> +++ b/Documentation/ABI/testing/sysfs-class-remoteproc
> @@ -16,11 +16,11 @@ Description: Remote processor state
>
> Reports the state of the remote processor, which will be one of:
>
> - "offline"
> - "suspended"
> - "running"
> - "crashed"
> - "invalid"
> + - "offline"
> + - "suspended"
> + - "running"
> + - "crashed"
> + - "invalid"
>
> "offline" means the remote processor is powered off.
>
> @@ -38,8 +38,8 @@ Description: Remote processor state
> Writing this file controls the state of the remote processor.
> The following states can be written:
>
> - "start"
> - "stop"
> + - "start"
> + - "stop"
>
> Writing "start" will attempt to start the processor running the
> firmware indicated by, or written to,
> diff --git a/Documentation/ABI/testing/sysfs-class-rtc-rtc0-device-rtc_calibration b/Documentation/ABI/testing/sysfs-class-rtc-rtc0-device-rtc_calibration
> index ec950c93e5c6..ee8ed6494a01 100644
> --- a/Documentation/ABI/testing/sysfs-class-rtc-rtc0-device-rtc_calibration
> +++ b/Documentation/ABI/testing/sysfs-class-rtc-rtc0-device-rtc_calibration
> @@ -7,6 +7,7 @@ Description: Attribute for calibrating ST-Ericsson AB8500 Real Time Clock
> calibrate the AB8500.s 32KHz Real Time Clock.
> Every 60 seconds the AB8500 will correct the RTC's value
> by adding to it the value of this attribute.
> +
> The range of the attribute is -127 to +127 in units of
> 30.5 micro-seconds (half-parts-per-million of the 32KHz clock)
> Users: The /vendor/st-ericsson/base_utilities/core/rtc_calibration
> diff --git a/Documentation/ABI/testing/sysfs-class-uwb_rc b/Documentation/ABI/testing/sysfs-class-uwb_rc
> index a0578751c1e3..6c5dcad21e19 100644
> --- a/Documentation/ABI/testing/sysfs-class-uwb_rc
> +++ b/Documentation/ABI/testing/sysfs-class-uwb_rc
> @@ -66,11 +66,14 @@ Description:
> <channel> <type> [<bpst offset>]
>
> to start (or stop) scanning on a channel. <type> is one of:
> - 0 - scan
> - 1 - scan outside BP
> - 2 - scan while inactive
> - 3 - scanning disabled
> - 4 - scan (with start time of <bpst offset>)
> +
> + == =======================================
> + 0 scan
> + 1 scan outside BP
> + 2 scan while inactive
> + 3 scanning disabled
> + 4 scan (with start time of <bpst offset>)
> + == =======================================
>
> What: /sys/class/uwb_rc/uwbN/mac_address
> Date: July 2008
> diff --git a/Documentation/ABI/testing/sysfs-class-watchdog b/Documentation/ABI/testing/sysfs-class-watchdog
> index 9860a8b2ba75..585caecda3a5 100644
> --- a/Documentation/ABI/testing/sysfs-class-watchdog
> +++ b/Documentation/ABI/testing/sysfs-class-watchdog
> @@ -91,10 +91,13 @@ Description:
> h/w strapping (for WDT2 only).
>
> At alternate flash the 'access_cs0' sysfs node provides:
> - ast2400: a way to get access to the primary SPI flash
> +
> + ast2400:
> + a way to get access to the primary SPI flash
> chip at CS0 after booting from the alternate
> chip at CS1.
> - ast2500: a way to restore the normal address mapping
> + ast2500:
> + a way to restore the normal address mapping
> from (CS0->CS1, CS1->CS0) to (CS0->CS0,
> CS1->CS1).
>
> diff --git a/Documentation/ABI/testing/sysfs-dev b/Documentation/ABI/testing/sysfs-dev
> index a9f2b8b0530f..d1739063e762 100644
> --- a/Documentation/ABI/testing/sysfs-dev
> +++ b/Documentation/ABI/testing/sysfs-dev
> @@ -9,9 +9,10 @@ Description: The /sys/dev tree provides a method to look up the sysfs
> the form "<major>:<minor>". These links point to the
> corresponding sysfs path for the given device.
>
> - Example:
> - $ readlink /sys/dev/block/8:32
> - ../../block/sdc
> + Example::
> +
> + $ readlink /sys/dev/block/8:32
> + ../../block/sdc
>
> Entries in /sys/dev/char and /sys/dev/block will be
> dynamically created and destroyed as devices enter and
> diff --git a/Documentation/ABI/testing/sysfs-devices-mapping b/Documentation/ABI/testing/sysfs-devices-mapping
> index 490ccfd67f12..8d202bac9394 100644
> --- a/Documentation/ABI/testing/sysfs-devices-mapping
> +++ b/Documentation/ABI/testing/sysfs-devices-mapping
> @@ -8,26 +8,27 @@ Description:
> block.
> For example, on 4-die Xeon platform with up to 6 IIO stacks per
> die and, therefore, 6 IIO PMON blocks per die, the mapping of
> - IIO PMON block 0 exposes as the following:
> + IIO PMON block 0 exposes as the following::
>
> - $ ls /sys/devices/uncore_iio_0/die*
> - -r--r--r-- /sys/devices/uncore_iio_0/die0
> - -r--r--r-- /sys/devices/uncore_iio_0/die1
> - -r--r--r-- /sys/devices/uncore_iio_0/die2
> - -r--r--r-- /sys/devices/uncore_iio_0/die3
> + $ ls /sys/devices/uncore_iio_0/die*
> + -r--r--r-- /sys/devices/uncore_iio_0/die0
> + -r--r--r-- /sys/devices/uncore_iio_0/die1
> + -r--r--r-- /sys/devices/uncore_iio_0/die2
> + -r--r--r-- /sys/devices/uncore_iio_0/die3
>
> - $ tail /sys/devices/uncore_iio_0/die*
> - ==> /sys/devices/uncore_iio_0/die0 <==
> - 0000:00
> - ==> /sys/devices/uncore_iio_0/die1 <==
> - 0000:40
> - ==> /sys/devices/uncore_iio_0/die2 <==
> - 0000:80
> - ==> /sys/devices/uncore_iio_0/die3 <==
> - 0000:c0
> + $ tail /sys/devices/uncore_iio_0/die*
> + ==> /sys/devices/uncore_iio_0/die0 <==
> + 0000:00
> + ==> /sys/devices/uncore_iio_0/die1 <==
> + 0000:40
> + ==> /sys/devices/uncore_iio_0/die2 <==
> + 0000:80
> + ==> /sys/devices/uncore_iio_0/die3 <==
> + 0000:c0
>
> - Which means:
> - IIO PMU 0 on die 0 belongs to PCI RP on bus 0x00, domain 0x0000
> - IIO PMU 0 on die 1 belongs to PCI RP on bus 0x40, domain 0x0000
> - IIO PMU 0 on die 2 belongs to PCI RP on bus 0x80, domain 0x0000
> - IIO PMU 0 on die 3 belongs to PCI RP on bus 0xc0, domain 0x0000
> + Which means::
> +
> + IIO PMU 0 on die 0 belongs to PCI RP on bus 0x00, domain 0x0000
> + IIO PMU 0 on die 1 belongs to PCI RP on bus 0x40, domain 0x0000
> + IIO PMU 0 on die 2 belongs to PCI RP on bus 0x80, domain 0x0000
> + IIO PMU 0 on die 3 belongs to PCI RP on bus 0xc0, domain 0x0000
> diff --git a/Documentation/ABI/testing/sysfs-devices-memory b/Documentation/ABI/testing/sysfs-devices-memory
> index deef3b5723cf..2da2b1fba2c1 100644
> --- a/Documentation/ABI/testing/sysfs-devices-memory
> +++ b/Documentation/ABI/testing/sysfs-devices-memory
> @@ -47,16 +47,19 @@ Description:
> online/offline state of the memory section. When written,
> root can toggle the the online/offline state of a removable
> memory section (see removable file description above)
> - using the following commands.
> - # echo online > /sys/devices/system/memory/memoryX/state
> - # echo offline > /sys/devices/system/memory/memoryX/state
> + using the following commands::
> +
> + # echo online > /sys/devices/system/memory/memoryX/state
> + # echo offline > /sys/devices/system/memory/memoryX/state
>
> For example, if /sys/devices/system/memory/memory22/removable
> contains a value of 1 and
> /sys/devices/system/memory/memory22/state contains the
> string "online" the following command can be executed by
> - by root to offline that section.
> - # echo offline > /sys/devices/system/memory/memory22/state
> + by root to offline that section::
> +
> + # echo offline > /sys/devices/system/memory/memory22/state
> +
> Users: hotplug memory remove tools
> http://www.ibm.com/developerworks/wikis/display/LinuxP/powerpc-utils
>
> @@ -78,6 +81,7 @@ Description:
>
> For example, the following symbolic link is created for
> memory section 9 on node0:
> +
> /sys/devices/system/memory/memory9/node0 -> ../../node/node0
>
>
> @@ -90,4 +94,5 @@ Description:
> points to the corresponding /sys/devices/system/memory/memoryY
> memory section directory. For example, the following symbolic
> link is created for memory section 9 on node0.
> +
> /sys/devices/system/node/node0/memory9 -> ../../memory/memory9
> diff --git a/Documentation/ABI/testing/sysfs-devices-platform-_UDC_-gadget b/Documentation/ABI/testing/sysfs-devices-platform-_UDC_-gadget
> index d548eaac230a..40f29a01fd14 100644
> --- a/Documentation/ABI/testing/sysfs-devices-platform-_UDC_-gadget
> +++ b/Documentation/ABI/testing/sysfs-devices-platform-_UDC_-gadget
> @@ -3,8 +3,9 @@ Date: April 2010
> Contact: Fabien Chouteau <fabien.chouteau at barco.com>
> Description:
> Show the suspend state of an USB composite gadget.
> - 1 -> suspended
> - 0 -> resumed
> +
> + - 1 -> suspended
> + - 0 -> resumed
>
> (_UDC_ is the name of the USB Device Controller driver)
>
> @@ -17,5 +18,6 @@ Description:
> Storage mode.
>
> Possible values are:
> - 1 -> ignore the FUA flag
> - 0 -> obey the FUA flag
> +
> + - 1 -> ignore the FUA flag
> + - 0 -> obey the FUA flag
> diff --git a/Documentation/ABI/testing/sysfs-devices-platform-ipmi b/Documentation/ABI/testing/sysfs-devices-platform-ipmi
> index afb5db856e1c..07df0ddc0b69 100644
> --- a/Documentation/ABI/testing/sysfs-devices-platform-ipmi
> +++ b/Documentation/ABI/testing/sysfs-devices-platform-ipmi
> @@ -123,38 +123,40 @@ KernelVersion: v4.15
> Contact: openipmi-developer at lists.sourceforge.net
> Description:
>
> - idles: (RO) Number of times the interface was
> + ====================== ========================================
> + idles (RO) Number of times the interface was
> idle while being polled.
>
> - watchdog_pretimeouts: (RO) Number of watchdog pretimeouts.
> + watchdog_pretimeouts (RO) Number of watchdog pretimeouts.
>
> - complete_transactions: (RO) Number of completed messages.
> + complete_transactions (RO) Number of completed messages.
>
> - events: (RO) Number of IPMI events received from
> + events (RO) Number of IPMI events received from
> the hardware.
>
> - interrupts: (RO) Number of interrupts the driver
> + interrupts (RO) Number of interrupts the driver
> handled.
>
> - hosed_count: (RO) Number of times the hardware didn't
> + hosed_count (RO) Number of times the hardware didn't
> follow the state machine.
>
> - long_timeouts: (RO) Number of times the driver
> + long_timeouts (RO) Number of times the driver
> requested a timer while nothing was in
> progress.
>
> - flag_fetches: (RO) Number of times the driver
> + flag_fetches (RO) Number of times the driver
> requested flags from the hardware.
>
> - attentions: (RO) Number of time the driver got an
> + attentions (RO) Number of time the driver got an
> ATTN from the hardware.
>
> - incoming_messages: (RO) Number of asynchronous messages
> + incoming_messages (RO) Number of asynchronous messages
> received.
>
> - short_timeouts: (RO) Number of times the driver
> + short_timeouts (RO) Number of times the driver
> requested a timer while an operation was
> in progress.
> + ====================== ========================================
>
>
> What: /sys/devices/platform/ipmi_si.*/interrupts_enabled
> @@ -201,38 +203,40 @@ Date: Sep, 2017
> KernelVersion: v4.15
> Contact: openipmi-developer at lists.sourceforge.net
> Description:
> - hosed: (RO) Number of times the hardware didn't
> + ====================== ========================================
> + hosed (RO) Number of times the hardware didn't
> follow the state machine.
>
> - alerts: (RO) Number of alerts received.
> + alerts (RO) Number of alerts received.
>
> - sent_messages: (RO) Number of total messages sent.
> + sent_messages (RO) Number of total messages sent.
>
> - sent_message_parts: (RO) Number of message parts sent.
> + sent_message_parts (RO) Number of message parts sent.
> Messages may be broken into parts if
> they are long.
>
> - received_messages: (RO) Number of message responses
> + received_messages (RO) Number of message responses
> received.
>
> - received_message_parts: (RO) Number of message fragments
> + received_message_parts (RO) Number of message fragments
> received.
>
> - events: (RO) Number of received events.
> + events (RO) Number of received events.
>
> - watchdog_pretimeouts: (RO) Number of watchdog pretimeouts.
> + watchdog_pretimeouts (RO) Number of watchdog pretimeouts.
>
> - flag_fetches: (RO) Number of times a flag fetch was
> + flag_fetches (RO) Number of times a flag fetch was
> requested.
>
> - send_retries: (RO) Number of time a message was
> + send_retries (RO) Number of time a message was
> retried.
>
> - receive_retries: (RO) Number of times the receive of a
> + receive_retries (RO) Number of times the receive of a
> message was retried.
>
> - send_errors: (RO) Number of times the send of a
> + send_errors (RO) Number of times the send of a
> message failed.
>
> - receive_errors: (RO) Number of errors in receiving
> + receive_errors (RO) Number of errors in receiving
> messages.
> + ====================== ========================================
> diff --git a/Documentation/ABI/testing/sysfs-devices-system-cpu b/Documentation/ABI/testing/sysfs-devices-system-cpu
> index 274c337ec6a9..1a04ca8162ad 100644
> --- a/Documentation/ABI/testing/sysfs-devices-system-cpu
> +++ b/Documentation/ABI/testing/sysfs-devices-system-cpu
> @@ -169,7 +169,7 @@ Description:
> observed CPU idle duration was too short for it
> (a count).
>
> - below: (RO) Number of times this state was entered, but the
> + below: (RO) Number of times this state was entered, but the
> observed CPU idle duration was too long for it
> (a count).
> ======== ==== =================================================
> @@ -601,7 +601,7 @@ Description: Secure Virtual Machine
> Facility in POWER9 and newer processors. i.e., it is a Secure
> Virtual Machine.
>
> -What: /sys/devices/system/cpu/cpuX/purr
> +What: /sys/devices/system/cpu/cpuX/purr
> Date: Apr 2005
> Contact: Linux for PowerPC mailing list <linuxppc-dev at ozlabs.org>
> Description: PURR ticks for this CPU since the system boot.
> diff --git a/Documentation/ABI/testing/sysfs-driver-hid-lenovo b/Documentation/ABI/testing/sysfs-driver-hid-lenovo
> index 53a0725962e1..aee85ca1f6be 100644
> --- a/Documentation/ABI/testing/sysfs-driver-hid-lenovo
> +++ b/Documentation/ABI/testing/sysfs-driver-hid-lenovo
> @@ -3,14 +3,18 @@ Date: July 2011
> Contact: linux-input at vger.kernel.org
> Description: This controls if mouse clicks should be generated if the trackpoint is quickly pressed. How fast this press has to be
> is being controlled by press_speed.
> +
> Values are 0 or 1.
> +
> Applies to Thinkpad USB Keyboard with TrackPoint.
>
> What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/dragging
> Date: July 2011
> Contact: linux-input at vger.kernel.org
> Description: If this setting is enabled, it is possible to do dragging by pressing the trackpoint. This requires press_to_select to be enabled.
> +
> Values are 0 or 1.
> +
> Applies to Thinkpad USB Keyboard with TrackPoint.
>
> What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/release_to_select
> @@ -25,7 +29,9 @@ Date: July 2011
> Contact: linux-input at vger.kernel.org
> Description: This setting controls if the mouse click events generated by pressing the trackpoint (if press_to_select is enabled) generate
> a left or right mouse button click.
> +
> Values are 0 or 1.
> +
> Applies to Thinkpad USB Keyboard with TrackPoint.
>
> What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/sensitivity
> @@ -39,12 +45,16 @@ What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-
> Date: July 2011
> Contact: linux-input at vger.kernel.org
> Description: This setting controls how fast the trackpoint needs to be pressed to generate a mouse click if press_to_select is enabled.
> +
> Values are decimal integers from 1 (slowest) to 255 (fastest).
> +
> Applies to Thinkpad USB Keyboard with TrackPoint.
>
> What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/fn_lock
> Date: July 2014
> Contact: linux-input at vger.kernel.org
> Description: This setting controls whether Fn Lock is enabled on the keyboard (i.e. if F1 is Mute or F1)
> +
> Values are 0 or 1
> +
> Applies to ThinkPad Compact (USB|Bluetooth) Keyboard with TrackPoint.
> diff --git a/Documentation/ABI/testing/sysfs-driver-hid-ntrig b/Documentation/ABI/testing/sysfs-driver-hid-ntrig
> index e574a5625efe..0e323a5cec6c 100644
> --- a/Documentation/ABI/testing/sysfs-driver-hid-ntrig
> +++ b/Documentation/ABI/testing/sysfs-driver-hid-ntrig
> @@ -29,12 +29,13 @@ Contact: linux-input at vger.kernel.org
> Description:
> Threholds to override activation slack.
>
> - activation_width: (RW) Width threshold to immediately
> + ================= =====================================
> + activation_width (RW) Width threshold to immediately
> start processing touch events.
>
> - activation_height: (RW) Height threshold to immediately
> + activation_height (RW) Height threshold to immediately
> start processing touch events.
> -
> + ================= =====================================
>
> What: /sys/bus/hid/drivers/ntrig/<dev>/min_width
> What: /sys/bus/hid/drivers/ntrig/<dev>/min_height
> @@ -44,11 +45,13 @@ Contact: linux-input at vger.kernel.org
> Description:
> Minimum size contact accepted.
>
> - min_width: (RW) Minimum touch contact width to decide
> + ========== ===========================================
> + min_width (RW) Minimum touch contact width to decide
> activation and activity.
>
> - min_height: (RW) Minimum touch contact height to decide
> + min_height (RW) Minimum touch contact height to decide
> activation and activity.
> + ========== ===========================================
>
>
> What: /sys/bus/hid/drivers/ntrig/<dev>/sensor_physical_width
> diff --git a/Documentation/ABI/testing/sysfs-driver-hid-roccat-kone b/Documentation/ABI/testing/sysfs-driver-hid-roccat-kone
> index 8f7982c70d72..11cd9bf0ad18 100644
> --- a/Documentation/ABI/testing/sysfs-driver-hid-roccat-kone
> +++ b/Documentation/ABI/testing/sysfs-driver-hid-roccat-kone
> @@ -3,17 +3,21 @@ Date: March 2010
> Contact: Stefan Achatz <erazor_de at users.sourceforge.net>
> Description: It is possible to switch the dpi setting of the mouse with the
> press of a button.
> +
> When read, this file returns the raw number of the actual dpi
> setting reported by the mouse. This number has to be further
> processed to receive the real dpi value:
>
> + ===== =====
> VALUE DPI
> + ===== =====
> 1 800
> 2 1200
> 3 1600
> 4 2000
> 5 2400
> 6 3200
> + ===== =====
>
> This file is readonly.
> Users: http://roccat.sourceforge.net
> @@ -22,6 +26,7 @@ What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-
> Date: March 2010
> Contact: Stefan Achatz <erazor_de at users.sourceforge.net>
> Description: When read, this file returns the number of the actual profile.
> +
> This file is readonly.
> Users: http://roccat.sourceforge.net
>
> @@ -33,6 +38,7 @@ Description: When read, this file returns the raw integer version number of the
> further usage in other programs. To receive the real version
> number the decimal point has to be shifted 2 positions to the
> left. E.g. a returned value of 138 means 1.38
> +
> This file is readonly.
> Users: http://roccat.sourceforge.net
>
> @@ -43,10 +49,13 @@ Description: The mouse can store 5 profiles which can be switched by the
> press of a button. A profile holds information like button
> mappings, sensitivity, the colors of the 5 leds and light
> effects.
> +
> When read, these files return the respective profile. The
> returned data is 975 bytes in size.
> +
> When written, this file lets one write the respective profile
> data back to the mouse. The data has to be 975 bytes long.
> +
> The mouse will reject invalid data, whereas the profile number
> stored in the profile doesn't need to fit the number of the
> store.
> @@ -58,6 +67,7 @@ Contact: Stefan Achatz <erazor_de at users.sourceforge.net>
> Description: When read, this file returns the settings stored in the mouse.
> The size of the data is 36 bytes and holds information like the
> startup_profile, tcu state and calibration_data.
> +
> When written, this file lets write settings back to the mouse.
> The data has to be 36 bytes long. The mouse will reject invalid
> data.
> @@ -67,8 +77,10 @@ What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-
> Date: March 2010
> Contact: Stefan Achatz <erazor_de at users.sourceforge.net>
> Description: The integer value of this attribute ranges from 1 to 5.
> +
> When read, this attribute returns the number of the profile
> that's active when the mouse is powered on.
> +
> When written, this file sets the number of the startup profile
> and the mouse activates this profile immediately.
> Users: http://roccat.sourceforge.net
> @@ -80,9 +92,12 @@ Description: The mouse has a "Tracking Control Unit" which lets the user
> calibrate the laser power to fit the mousepad surface.
> When read, this file returns the current state of the TCU,
> where 0 means off and 1 means on.
> +
> Writing 0 in this file will switch the TCU off.
> +
> Writing 1 in this file will start the calibration which takes
> around 6 seconds to complete and activates the TCU.
> +
> Users: http://roccat.sourceforge.net
>
> What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/kone/roccatkone<minor>/weight
> @@ -93,14 +108,18 @@ Description: The mouse can be equipped with one of four supplied weights
> and its value can be read out. When read, this file returns the
> raw value returned by the mouse which eases further processing
> in other software.
> +
> The values map to the weights as follows:
>
> + ===== ======
> VALUE WEIGHT
> + ===== ======
> 0 none
> 1 5g
> 2 10g
> 3 15g
> 4 20g
> + ===== ======
>
> This file is readonly.
> Users: http://roccat.sourceforge.net
> diff --git a/Documentation/ABI/testing/sysfs-driver-hid-wiimote b/Documentation/ABI/testing/sysfs-driver-hid-wiimote
> index cd7b82a5c27d..3bf43d9dcdfe 100644
> --- a/Documentation/ABI/testing/sysfs-driver-hid-wiimote
> +++ b/Documentation/ABI/testing/sysfs-driver-hid-wiimote
> @@ -20,6 +20,7 @@ Description: This file contains the currently connected and initialized
> the official Nintendo Nunchuck extension and classic is the
> Nintendo Classic Controller extension. The motionp extension can
> be combined with the other two.
> +
> Starting with kernel-version 3.11 Motion Plus hotplugging is
> supported and if detected, it's no longer reported as static
> extension. You will get uevent notifications for the motion-plus
> diff --git a/Documentation/ABI/testing/sysfs-driver-input-exc3000 b/Documentation/ABI/testing/sysfs-driver-input-exc3000
> index 3d316d54f81c..cd7c578aef2c 100644
> --- a/Documentation/ABI/testing/sysfs-driver-input-exc3000
> +++ b/Documentation/ABI/testing/sysfs-driver-input-exc3000
> @@ -4,6 +4,7 @@ Contact: linux-input at vger.kernel.org
> Description: Reports the firmware version provided by the touchscreen, for example "00_T6" on a EXC80H60
>
> Access: Read
> +
> Valid values: Represented as string
>
> What: /sys/bus/i2c/devices/xxx/model
> @@ -12,4 +13,5 @@ Contact: linux-input at vger.kernel.org
> Description: Reports the model identification provided by the touchscreen, for example "Orion_1320" on a EXC80H60
>
> Access: Read
> +
> Valid values: Represented as string
> diff --git a/Documentation/ABI/testing/sysfs-driver-jz4780-efuse b/Documentation/ABI/testing/sysfs-driver-jz4780-efuse
> index bb6f5d6ceea0..4cf595d681e6 100644
> --- a/Documentation/ABI/testing/sysfs-driver-jz4780-efuse
> +++ b/Documentation/ABI/testing/sysfs-driver-jz4780-efuse
> @@ -4,7 +4,9 @@ Contact: PrasannaKumar Muralidharan <prasannatsmkumar at gmail.com>
> Description: read-only access to the efuse on the Ingenic JZ4780 SoC
> The SoC has a one time programmable 8K efuse that is
> split into segments. The driver supports read only.
> - The segments are
> + The segments are:
> +
> + ===== ======== =================
> 0x000 64 bit Random Number
> 0x008 128 bit Ingenic Chip ID
> 0x018 128 bit Customer ID
> @@ -12,5 +14,7 @@ Description: read-only access to the efuse on the Ingenic JZ4780 SoC
> 0x1E0 8 bit Protect Segment
> 0x1E1 2296 bit HDMI Key
> 0x300 2048 bit Security boot key
> + ===== ======== =================
> +
> Users: any user space application which wants to read the Chip
> and Customer ID
> diff --git a/Documentation/ABI/testing/sysfs-driver-pciback b/Documentation/ABI/testing/sysfs-driver-pciback
> index 73308c2b81b0..49f5fd0c8bbd 100644
> --- a/Documentation/ABI/testing/sysfs-driver-pciback
> +++ b/Documentation/ABI/testing/sysfs-driver-pciback
> @@ -7,8 +7,10 @@ Description:
> the format of DDDD:BB:DD.F-REG:SIZE:MASK will allow the guest
> to write and read from the PCI device. That is Domain:Bus:
> Device.Function-Register:Size:Mask (Domain is optional).
> - For example:
> - #echo 00:19.0-E0:2:FF > /sys/bus/pci/drivers/pciback/quirks
> + For example::
> +
> + #echo 00:19.0-E0:2:FF > /sys/bus/pci/drivers/pciback/quirks
> +
> will allow the guest to read and write to the configuration
> register 0x0E.
>
> diff --git a/Documentation/ABI/testing/sysfs-driver-ufs b/Documentation/ABI/testing/sysfs-driver-ufs
> index d1a352194d2e..adc0d0e91607 100644
> --- a/Documentation/ABI/testing/sysfs-driver-ufs
> +++ b/Documentation/ABI/testing/sysfs-driver-ufs
> @@ -18,6 +18,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows the device type. This is one of the UFS
> device descriptor parameters. The full information about
> the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/device_descriptor/device_class
> @@ -26,6 +27,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows the device class. This is one of the UFS
> device descriptor parameters. The full information about
> the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/device_descriptor/device_sub_class
> @@ -34,6 +36,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows the UFS storage subclass. This is one of
> the UFS device descriptor parameters. The full information
> about the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/device_descriptor/protocol
> @@ -43,6 +46,7 @@ Description: This file shows the protocol supported by an UFS device.
> This is one of the UFS device descriptor parameters.
> The full information about the descriptor could be found
> at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/device_descriptor/number_of_luns
> @@ -51,6 +55,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows number of logical units. This is one of
> the UFS device descriptor parameters. The full information
> about the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/device_descriptor/number_of_wluns
> @@ -60,6 +65,7 @@ Description: This file shows number of well known logical units.
> This is one of the UFS device descriptor parameters.
> The full information about the descriptor could be found
> at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/device_descriptor/boot_enable
> @@ -69,6 +75,7 @@ Description: This file shows value that indicates whether the device is
> enabled for boot. This is one of the UFS device descriptor
> parameters. The full information about the descriptor could
> be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/device_descriptor/descriptor_access_enable
> @@ -79,6 +86,7 @@ Description: This file shows value that indicates whether the device
> of the boot sequence. This is one of the UFS device descriptor
> parameters. The full information about the descriptor could
> be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/device_descriptor/initial_power_mode
> @@ -88,6 +96,7 @@ Description: This file shows value that defines the power mode after
> device initialization or hardware reset. This is one of
> the UFS device descriptor parameters. The full information
> about the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/device_descriptor/high_priority_lun
> @@ -96,6 +105,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows the high priority lun. This is one of
> the UFS device descriptor parameters. The full information
> about the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/device_descriptor/secure_removal_type
> @@ -104,6 +114,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows the secure removal type. This is one of
> the UFS device descriptor parameters. The full information
> about the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/device_descriptor/support_security_lun
> @@ -113,6 +124,7 @@ Description: This file shows whether the security lun is supported.
> This is one of the UFS device descriptor parameters.
> The full information about the descriptor could be found
> at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/device_descriptor/bkops_termination_latency
> @@ -122,6 +134,7 @@ Description: This file shows the background operations termination
> latency. This is one of the UFS device descriptor parameters.
> The full information about the descriptor could be found
> at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/device_descriptor/initial_active_icc_level
> @@ -130,6 +143,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows the initial active ICC level. This is one
> of the UFS device descriptor parameters. The full information
> about the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/device_descriptor/specification_version
> @@ -138,6 +152,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows the specification version. This is one
> of the UFS device descriptor parameters. The full information
> about the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/device_descriptor/manufacturing_date
> @@ -147,6 +162,7 @@ Description: This file shows the manufacturing date in BCD format.
> This is one of the UFS device descriptor parameters.
> The full information about the descriptor could be found
> at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/device_descriptor/manufacturer_id
> @@ -155,6 +171,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows the manufacturee ID. This is one of the
> UFS device descriptor parameters. The full information about
> the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/device_descriptor/rtt_capability
> @@ -164,6 +181,7 @@ Description: This file shows the maximum number of outstanding RTTs
> supported by the device. This is one of the UFS device
> descriptor parameters. The full information about
> the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/device_descriptor/rtc_update
> @@ -173,6 +191,7 @@ Description: This file shows the frequency and method of the realtime
> clock update. This is one of the UFS device descriptor
> parameters. The full information about the descriptor
> could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/device_descriptor/ufs_features
> @@ -182,6 +201,7 @@ Description: This file shows which features are supported by the device.
> This is one of the UFS device descriptor parameters.
> The full information about the descriptor could be
> found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/device_descriptor/ffu_timeout
> @@ -190,6 +210,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows the FFU timeout. This is one of the
> UFS device descriptor parameters. The full information
> about the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/device_descriptor/queue_depth
> @@ -198,6 +219,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows the device queue depth. This is one of the
> UFS device descriptor parameters. The full information
> about the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/device_descriptor/device_version
> @@ -206,6 +228,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows the device version. This is one of the
> UFS device descriptor parameters. The full information
> about the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/device_descriptor/number_of_secure_wpa
> @@ -215,6 +238,7 @@ Description: This file shows number of secure write protect areas
> supported by the device. This is one of the UFS device
> descriptor parameters. The full information about
> the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/device_descriptor/psa_max_data_size
> @@ -225,6 +249,7 @@ Description: This file shows the maximum amount of data that may be
> This is one of the UFS device descriptor parameters.
> The full information about the descriptor could be found
> at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/device_descriptor/psa_state_timeout
> @@ -234,6 +259,7 @@ Description: This file shows the command maximum timeout for a change
> in PSA state. This is one of the UFS device descriptor
> parameters. The full information about the descriptor could
> be found at UFS specifications 2.1.
> +
> The file is read only.
>
>
> @@ -244,6 +270,7 @@ Description: This file shows the MIPI UniPro version number in BCD format.
> This is one of the UFS interconnect descriptor parameters.
> The full information about the descriptor could be found at
> UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/interconnect_descriptor/mphy_version
> @@ -253,6 +280,7 @@ Description: This file shows the MIPI M-PHY version number in BCD format.
> This is one of the UFS interconnect descriptor parameters.
> The full information about the descriptor could be found at
> UFS specifications 2.1.
> +
> The file is read only.
>
>
> @@ -264,6 +292,7 @@ Description: This file shows the total memory quantity available to
> of the UFS geometry descriptor parameters. The full
> information about the descriptor could be found at
> UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/max_number_of_luns
> @@ -273,6 +302,7 @@ Description: This file shows the maximum number of logical units
> supported by the UFS device. This is one of the UFS
> geometry descriptor parameters. The full information about
> the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/segment_size
> @@ -281,6 +311,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows the segment size. This is one of the UFS
> geometry descriptor parameters. The full information about
> the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/allocation_unit_size
> @@ -289,6 +320,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows the allocation unit size. This is one of
> the UFS geometry descriptor parameters. The full information
> about the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/min_addressable_block_size
> @@ -298,6 +330,7 @@ Description: This file shows the minimum addressable block size. This
> is one of the UFS geometry descriptor parameters. The full
> information about the descriptor could be found at UFS
> specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/optimal_read_block_size
> @@ -307,6 +340,7 @@ Description: This file shows the optimal read block size. This is one
> of the UFS geometry descriptor parameters. The full
> information about the descriptor could be found at UFS
> specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/optimal_write_block_size
> @@ -316,6 +350,7 @@ Description: This file shows the optimal write block size. This is one
> of the UFS geometry descriptor parameters. The full
> information about the descriptor could be found at UFS
> specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/max_in_buffer_size
> @@ -325,6 +360,7 @@ Description: This file shows the maximum data-in buffer size. This
> is one of the UFS geometry descriptor parameters. The full
> information about the descriptor could be found at UFS
> specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/max_out_buffer_size
> @@ -334,6 +370,7 @@ Description: This file shows the maximum data-out buffer size. This
> is one of the UFS geometry descriptor parameters. The full
> information about the descriptor could be found at UFS
> specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/rpmb_rw_size
> @@ -343,6 +380,7 @@ Description: This file shows the maximum number of RPMB frames allowed
> in Security Protocol In/Out. This is one of the UFS geometry
> descriptor parameters. The full information about the
> descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/dyn_capacity_resource_policy
> @@ -352,6 +390,7 @@ Description: This file shows the dynamic capacity resource policy. This
> is one of the UFS geometry descriptor parameters. The full
> information about the descriptor could be found at
> UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/data_ordering
> @@ -361,6 +400,7 @@ Description: This file shows support for out-of-order data transfer.
> This is one of the UFS geometry descriptor parameters.
> The full information about the descriptor could be found at
> UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/max_number_of_contexts
> @@ -370,6 +410,7 @@ Description: This file shows maximum available number of contexts which
> are supported by the device. This is one of the UFS geometry
> descriptor parameters. The full information about the
> descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/sys_data_tag_unit_size
> @@ -378,6 +419,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows system data tag unit size. This is one of
> the UFS geometry descriptor parameters. The full information
> about the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/sys_data_tag_resource_size
> @@ -388,6 +430,7 @@ Description: This file shows maximum storage area size allocated by
> This is one of the UFS geometry descriptor parameters.
> The full information about the descriptor could be found at
> UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/secure_removal_types
> @@ -397,6 +440,7 @@ Description: This file shows supported secure removal types. This is
> one of the UFS geometry descriptor parameters. The full
> information about the descriptor could be found at
> UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/memory_types
> @@ -406,6 +450,7 @@ Description: This file shows supported memory types. This is one of
> the UFS geometry descriptor parameters. The full
> information about the descriptor could be found at
> UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/*_memory_max_alloc_units
> @@ -416,6 +461,7 @@ Description: This file shows the maximum number of allocation units for
> enhanced type 1-4). This is one of the UFS geometry
> descriptor parameters. The full information about the
> descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/*_memory_capacity_adjustment_factor
> @@ -426,6 +472,7 @@ Description: This file shows the memory capacity adjustment factor for
> enhanced type 1-4). This is one of the UFS geometry
> descriptor parameters. The full information about the
> descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
>
> @@ -436,6 +483,7 @@ Description: This file shows preend of life information. This is one
> of the UFS health descriptor parameters. The full
> information about the descriptor could be found at
> UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/health_descriptor/life_time_estimation_a
> @@ -445,6 +493,7 @@ Description: This file shows indication of the device life time
> (method a). This is one of the UFS health descriptor
> parameters. The full information about the descriptor
> could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/health_descriptor/life_time_estimation_b
> @@ -454,6 +503,7 @@ Description: This file shows indication of the device life time
> (method b). This is one of the UFS health descriptor
> parameters. The full information about the descriptor
> could be found at UFS specifications 2.1.
> +
> The file is read only.
>
>
> @@ -464,6 +514,7 @@ Description: This file shows maximum VCC, VCCQ and VCCQ2 value for
> active ICC levels from 0 to 15. This is one of the UFS
> power descriptor parameters. The full information about
> the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
>
> @@ -473,6 +524,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file contains a device manufactureer name string.
> The full information about the descriptor could be found at
> UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/string_descriptors/product_name
> @@ -480,6 +532,7 @@ Date: February 2018
> Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file contains a product name string. The full information
> about the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/string_descriptors/oem_id
> @@ -487,6 +540,7 @@ Date: February 2018
> Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file contains a OEM ID string. The full information
> about the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/string_descriptors/serial_number
> @@ -495,6 +549,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file contains a device serial number string. The full
> information about the descriptor could be found at
> UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/string_descriptors/product_revision
> @@ -503,6 +558,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file contains a product revision string. The full
> information about the descriptor could be found at
> UFS specifications 2.1.
> +
> The file is read only.
>
>
> @@ -512,6 +568,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows boot LUN information. This is one of
> the UFS unit descriptor parameters. The full information
> about the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/class/scsi_device/*/device/unit_descriptor/lun_write_protect
> @@ -520,6 +577,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows LUN write protection status. This is one of
> the UFS unit descriptor parameters. The full information
> about the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/class/scsi_device/*/device/unit_descriptor/lun_queue_depth
> @@ -528,6 +586,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows LUN queue depth. This is one of the UFS
> unit descriptor parameters. The full information about
> the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/class/scsi_device/*/device/unit_descriptor/psa_sensitive
> @@ -536,6 +595,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows PSA sensitivity. This is one of the UFS
> unit descriptor parameters. The full information about
> the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/class/scsi_device/*/device/unit_descriptor/lun_memory_type
> @@ -544,6 +604,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows LUN memory type. This is one of the UFS
> unit descriptor parameters. The full information about
> the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/class/scsi_device/*/device/unit_descriptor/data_reliability
> @@ -553,6 +614,7 @@ Description: This file defines the device behavior when a power failure
> occurs during a write operation. This is one of the UFS
> unit descriptor parameters. The full information about
> the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/class/scsi_device/*/device/unit_descriptor/logical_block_size
> @@ -562,6 +624,7 @@ Description: This file shows the size of addressable logical blocks
> (calculated as an exponent with base 2). This is one of
> the UFS unit descriptor parameters. The full information about
> the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/class/scsi_device/*/device/unit_descriptor/logical_block_count
> @@ -571,6 +634,7 @@ Description: This file shows total number of addressable logical blocks.
> This is one of the UFS unit descriptor parameters. The full
> information about the descriptor could be found at
> UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/class/scsi_device/*/device/unit_descriptor/erase_block_size
> @@ -579,6 +643,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows the erase block size. This is one of
> the UFS unit descriptor parameters. The full information
> about the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/class/scsi_device/*/device/unit_descriptor/provisioning_type
> @@ -587,6 +652,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows the thin provisioning type. This is one of
> the UFS unit descriptor parameters. The full information
> about the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/class/scsi_device/*/device/unit_descriptor/physical_memory_resourse_count
> @@ -595,6 +661,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows the total physical memory resources. This is
> one of the UFS unit descriptor parameters. The full information
> about the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/class/scsi_device/*/device/unit_descriptor/context_capabilities
> @@ -603,6 +670,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows the context capabilities. This is one of
> the UFS unit descriptor parameters. The full information
> about the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/class/scsi_device/*/device/unit_descriptor/large_unit_granularity
> @@ -611,6 +679,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows the granularity of the LUN. This is one of
> the UFS unit descriptor parameters. The full information
> about the descriptor could be found at UFS specifications 2.1.
> +
> The file is read only.
>
>
> @@ -619,6 +688,7 @@ Date: February 2018
> Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows the device init status. The full information
> about the flag could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/flags/permanent_wpe
> @@ -627,6 +697,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows whether permanent write protection is enabled.
> The full information about the flag could be found at
> UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/flags/power_on_wpe
> @@ -636,6 +707,7 @@ Description: This file shows whether write protection is enabled on all
> logical units configured as power on write protected. The
> full information about the flag could be found at
> UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/flags/bkops_enable
> @@ -644,6 +716,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows whether the device background operations are
> enabled. The full information about the flag could be
> found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/flags/life_span_mode_enable
> @@ -652,6 +725,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows whether the device life span mode is enabled.
> The full information about the flag could be found at
> UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/flags/phy_resource_removal
> @@ -660,6 +734,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows whether physical resource removal is enable.
> The full information about the flag could be found at
> UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/flags/busy_rtc
> @@ -668,6 +743,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows whether the device is executing internal
> operation related to real time clock. The full information
> about the flag could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/flags/disable_fw_update
> @@ -676,6 +752,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows whether the device FW update is permanently
> disabled. The full information about the flag could be found
> at UFS specifications 2.1.
> +
> The file is read only.
>
>
> @@ -685,6 +762,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file provides the boot lun enabled UFS device attribute.
> The full information about the attribute could be found at
> UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/attributes/current_power_mode
> @@ -693,6 +771,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file provides the current power mode UFS device attribute.
> The full information about the attribute could be found at
> UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/attributes/active_icc_level
> @@ -701,6 +780,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file provides the active icc level UFS device attribute.
> The full information about the attribute could be found at
> UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/attributes/ooo_data_enabled
> @@ -709,6 +789,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file provides the out of order data transfer enabled UFS
> device attribute. The full information about the attribute
> could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/attributes/bkops_status
> @@ -717,6 +798,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file provides the background operations status UFS device
> attribute. The full information about the attribute could
> be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/attributes/purge_status
> @@ -725,6 +807,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file provides the purge operation status UFS device
> attribute. The full information about the attribute could
> be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/attributes/max_data_in_size
> @@ -733,6 +816,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows the maximum data size in a DATA IN
> UPIU. The full information about the attribute could
> be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/attributes/max_data_out_size
> @@ -741,6 +825,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file shows the maximum number of bytes that can be
> requested with a READY TO TRANSFER UPIU. The full information
> about the attribute could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/attributes/reference_clock_frequency
> @@ -749,6 +834,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file provides the reference clock frequency UFS device
> attribute. The full information about the attribute could
> be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/attributes/configuration_descriptor_lock
> @@ -765,6 +851,7 @@ Description: This file provides the maximum current number of
> outstanding RTTs in device that is allowed. The full
> information about the attribute could be found at
> UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/attributes/exception_event_control
> @@ -773,6 +860,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file provides the exception event control UFS device
> attribute. The full information about the attribute could
> be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/attributes/exception_event_status
> @@ -781,6 +869,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file provides the exception event status UFS device
> attribute. The full information about the attribute could
> be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/attributes/ffu_status
> @@ -789,6 +878,7 @@ Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file provides the ffu status UFS device attribute.
> The full information about the attribute could be found at
> UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/attributes/psa_state
> @@ -796,6 +886,7 @@ Date: February 2018
> Contact: Stanislav Nijnikov <stanislav.nijnikov at wdc.com>
> Description: This file show the PSA feature status. The full information
> about the attribute could be found at UFS specifications 2.1.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/attributes/psa_data_size
> @@ -805,6 +896,7 @@ Description: This file shows the amount of data that the host plans to
> load to all logical units in pre-soldering state.
> The full information about the attribute could be found at
> UFS specifications 2.1.
> +
> The file is read only.
>
>
> @@ -815,6 +907,7 @@ Description: This file shows the The amount of physical memory needed
> to be removed from the physical memory resources pool of
> the particular logical unit. The full information about
> the attribute could be found at UFS specifications 2.1.
> +
> The file is read only.
>
>
> @@ -824,24 +917,28 @@ Contact: Subhash Jadavani <subhashj at codeaurora.org>
> Description: This entry could be used to set or show the UFS device
> runtime power management level. The current driver
> implementation supports 6 levels with next target states:
> - 0 - an UFS device will stay active, an UIC link will
> - stay active
> - 1 - an UFS device will stay active, an UIC link will
> - hibernate
> - 2 - an UFS device will moved to sleep, an UIC link will
> - stay active
> - 3 - an UFS device will moved to sleep, an UIC link will
> - hibernate
> - 4 - an UFS device will be powered off, an UIC link will
> - hibernate
> - 5 - an UFS device will be powered off, an UIC link will
> - be powered off
> +
> + == ====================================================
> + 0 an UFS device will stay active, an UIC link will
> + stay active
> + 1 an UFS device will stay active, an UIC link will
> + hibernate
> + 2 an UFS device will moved to sleep, an UIC link will
> + stay active
> + 3 an UFS device will moved to sleep, an UIC link will
> + hibernate
> + 4 an UFS device will be powered off, an UIC link will
> + hibernate
> + 5 an UFS device will be powered off, an UIC link will
> + be powered off
> + == ====================================================
>
> What: /sys/bus/platform/drivers/ufshcd/*/rpm_target_dev_state
> Date: February 2018
> Contact: Subhash Jadavani <subhashj at codeaurora.org>
> Description: This entry shows the target power mode of an UFS device
> for the chosen runtime power management level.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/rpm_target_link_state
> @@ -849,6 +946,7 @@ Date: February 2018
> Contact: Subhash Jadavani <subhashj at codeaurora.org>
> Description: This entry shows the target state of an UFS UIC link
> for the chosen runtime power management level.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/spm_lvl
> @@ -857,24 +955,28 @@ Contact: Subhash Jadavani <subhashj at codeaurora.org>
> Description: This entry could be used to set or show the UFS device
> system power management level. The current driver
> implementation supports 6 levels with next target states:
> - 0 - an UFS device will stay active, an UIC link will
> - stay active
> - 1 - an UFS device will stay active, an UIC link will
> - hibernate
> - 2 - an UFS device will moved to sleep, an UIC link will
> - stay active
> - 3 - an UFS device will moved to sleep, an UIC link will
> - hibernate
> - 4 - an UFS device will be powered off, an UIC link will
> - hibernate
> - 5 - an UFS device will be powered off, an UIC link will
> - be powered off
> +
> + == ====================================================
> + 0 an UFS device will stay active, an UIC link will
> + stay active
> + 1 an UFS device will stay active, an UIC link will
> + hibernate
> + 2 an UFS device will moved to sleep, an UIC link will
> + stay active
> + 3 an UFS device will moved to sleep, an UIC link will
> + hibernate
> + 4 an UFS device will be powered off, an UIC link will
> + hibernate
> + 5 an UFS device will be powered off, an UIC link will
> + be powered off
> + == ====================================================
>
> What: /sys/bus/platform/drivers/ufshcd/*/spm_target_dev_state
> Date: February 2018
> Contact: Subhash Jadavani <subhashj at codeaurora.org>
> Description: This entry shows the target power mode of an UFS device
> for the chosen system power management level.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/spm_target_link_state
> @@ -882,18 +984,21 @@ Date: February 2018
> Contact: Subhash Jadavani <subhashj at codeaurora.org>
> Description: This entry shows the target state of an UFS UIC link
> for the chosen system power management level.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/device_descriptor/wb_presv_us_en
> Date: June 2020
> Contact: Asutosh Das <asutoshd at codeaurora.org>
> Description: This entry shows if preserve user-space was configured
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/device_descriptor/wb_shared_alloc_units
> Date: June 2020
> Contact: Asutosh Das <asutoshd at codeaurora.org>
> Description: This entry shows the shared allocated units of WB buffer
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/device_descriptor/wb_type
> @@ -901,6 +1006,7 @@ Date: June 2020
> Contact: Asutosh Das <asutoshd at codeaurora.org>
> Description: This entry shows the configured WB type.
> 0x1 for shared buffer mode. 0x0 for dedicated buffer mode.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/wb_buff_cap_adj
> @@ -910,6 +1016,7 @@ Description: This entry shows the total user-space decrease in shared
> buffer mode.
> The value of this parameter is 3 for TLC NAND when SLC mode
> is used as WriteBooster Buffer. 2 for MLC NAND.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/wb_max_alloc_units
> @@ -917,6 +1024,7 @@ Date: June 2020
> Contact: Asutosh Das <asutoshd at codeaurora.org>
> Description: This entry shows the Maximum total WriteBooster Buffer size
> which is supported by the entire device.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/wb_max_wb_luns
> @@ -924,6 +1032,7 @@ Date: June 2020
> Contact: Asutosh Das <asutoshd at codeaurora.org>
> Description: This entry shows the maximum number of luns that can support
> WriteBooster.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/wb_sup_red_type
> @@ -937,46 +1046,59 @@ Description: The supportability of user space reduction mode
> preserve user space type.
> 02h: Device can be configured in either user space
> reduction type or preserve user space type.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/geometry_descriptor/wb_sup_wb_type
> Date: June 2020
> Contact: Asutosh Das <asutoshd at codeaurora.org>
> Description: The supportability of WriteBooster Buffer type.
> - 00h: LU based WriteBooster Buffer configuration
> - 01h: Single shared WriteBooster Buffer
> - configuration
> - 02h: Supporting both LU based WriteBooster
> - Buffer and Single shared WriteBooster Buffer
> - configuration
> +
> + === ==========================================================
> + 00h LU based WriteBooster Buffer configuration
> + 01h Single shared WriteBooster Buffer configuration
> + 02h Supporting both LU based WriteBooster.
> + Buffer and Single shared WriteBooster Buffer configuration
> + === ==========================================================
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/flags/wb_enable
> Date: June 2020
> Contact: Asutosh Das <asutoshd at codeaurora.org>
> Description: This entry shows the status of WriteBooster.
> - 0: WriteBooster is not enabled.
> - 1: WriteBooster is enabled
> +
> + == ============================
> + 0 WriteBooster is not enabled.
> + 1 WriteBooster is enabled
> + == ============================
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/flags/wb_flush_en
> Date: June 2020
> Contact: Asutosh Das <asutoshd at codeaurora.org>
> Description: This entry shows if flush is enabled.
> - 0: Flush operation is not performed.
> - 1: Flush operation is performed.
> +
> + == =================================
> + 0 Flush operation is not performed.
> + 1 Flush operation is performed.
> + == =================================
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/flags/wb_flush_during_h8
> Date: June 2020
> Contact: Asutosh Das <asutoshd at codeaurora.org>
> Description: Flush WriteBooster Buffer during hibernate state.
> - 0: Device is not allowed to flush the
> - WriteBooster Buffer during link hibernate
> - state.
> - 1: Device is allowed to flush the
> - WriteBooster Buffer during link hibernate
> - state
> +
> + == =================================================
> + 0 Device is not allowed to flush the
> + WriteBooster Buffer during link hibernate state.
> + 1 Device is allowed to flush the
> + WriteBooster Buffer during link hibernate state.
> + == =================================================
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/attributes/wb_avail_buf
> @@ -984,23 +1106,30 @@ Date: June 2020
> Contact: Asutosh Das <asutoshd at codeaurora.org>
> Description: This entry shows the amount of unused WriteBooster buffer
> available.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/attributes/wb_cur_buf
> Date: June 2020
> Contact: Asutosh Das <asutoshd at codeaurora.org>
> Description: This entry shows the amount of unused current buffer.
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/attributes/wb_flush_status
> Date: June 2020
> Contact: Asutosh Das <asutoshd at codeaurora.org>
> Description: This entry shows the flush operation status.
> - 00h: idle
> - 01h: Flush operation in progress
> - 02h: Flush operation stopped prematurely.
> - 03h: Flush operation completed successfully
> - 04h: Flush operation general failure
> +
> +
> + === ======================================
> + 00h idle
> + 01h Flush operation in progress
> + 02h Flush operation stopped prematurely.
> + 03h Flush operation completed successfully
> + 04h Flush operation general failure
> + === ======================================
> +
> The file is read only.
>
> What: /sys/bus/platform/drivers/ufshcd/*/attributes/wb_life_time_est
> @@ -1008,9 +1137,13 @@ Date: June 2020
> Contact: Asutosh Das <asutoshd at codeaurora.org>
> Description: This entry shows an indication of the WriteBooster Buffer
> lifetime based on the amount of performed program/erase cycles
> - 01h: 0% - 10% WriteBooster Buffer life time used
> +
> + === =============================================
> + 01h 0% - 10% WriteBooster Buffer life time used
> ...
> - 0Ah: 90% - 100% WriteBooster Buffer life time used
> + 0Ah 90% - 100% WriteBooster Buffer life time used
> + === =============================================
> +
> The file is read only.
>
> What: /sys/class/scsi_device/*/device/unit_descriptor/wb_buf_alloc_units
> @@ -1018,4 +1151,5 @@ Date: June 2020
> Contact: Asutosh Das <asutoshd at codeaurora.org>
> Description: This entry shows the configured size of WriteBooster buffer.
> 0400h corresponds to 4GB.
> +
> The file is read only.
> diff --git a/Documentation/ABI/testing/sysfs-driver-w1_ds28e17 b/Documentation/ABI/testing/sysfs-driver-w1_ds28e17
> index d301e7017afe..e92aba4eb594 100644
> --- a/Documentation/ABI/testing/sysfs-driver-w1_ds28e17
> +++ b/Documentation/ABI/testing/sysfs-driver-w1_ds28e17
> @@ -5,7 +5,9 @@ Contact: Jan Kandziora <jjj at gmx.de>
> Description: When written, this file sets the I2C speed on the connected
> DS28E17 chip. When read, it reads the current setting from
> the DS28E17 chip.
> +
> Valid values: 100, 400, 900 [kBaud].
> +
> Default 100, can be set by w1_ds28e17.speed= module parameter.
> Users: w1_ds28e17 driver
>
> @@ -17,5 +19,6 @@ Description: When written, this file sets the multiplier used to calculate
> the busy timeout for I2C operations on the connected DS28E17
> chip. When read, returns the current setting.
> Valid values: 1 to 9.
> +
> Default 1, can be set by w1_ds28e17.stretch= module parameter.
> Users: w1_ds28e17 driver
> diff --git a/Documentation/ABI/testing/sysfs-firmware-acpi b/Documentation/ABI/testing/sysfs-firmware-acpi
> index e4afc2538210..b16d30a71709 100644
> --- a/Documentation/ABI/testing/sysfs-firmware-acpi
> +++ b/Documentation/ABI/testing/sysfs-firmware-acpi
> @@ -81,11 +81,11 @@ Description:
> $ cd /sys/firmware/acpi/interrupts
> $ grep . *
> error: 0
> - ff_gbl_lock: 0 enable
> - ff_pmtimer: 0 invalid
> - ff_pwr_btn: 0 enable
> - ff_rt_clk: 2 disable
> - ff_slp_btn: 0 invalid
> + ff_gbl_lock: 0 enable
> + ff_pmtimer: 0 invalid
> + ff_pwr_btn: 0 enable
> + ff_rt_clk: 2 disable
> + ff_slp_btn: 0 invalid
> gpe00: 0 invalid
> gpe01: 0 enable
> gpe02: 108 enable
> @@ -118,9 +118,9 @@ Description:
> gpe1D: 0 invalid
> gpe1E: 0 invalid
> gpe1F: 0 invalid
> - gpe_all: 1192
> - sci: 1194
> - sci_not: 0
> + gpe_all: 1192
> + sci: 1194
> + sci_not: 0
>
> =========== ==================================================
> sci The number of times the ACPI SCI
> diff --git a/Documentation/ABI/testing/sysfs-firmware-efi-esrt b/Documentation/ABI/testing/sysfs-firmware-efi-esrt
> index 6e431d1a4e79..31b57676d4ad 100644
> --- a/Documentation/ABI/testing/sysfs-firmware-efi-esrt
> +++ b/Documentation/ABI/testing/sysfs-firmware-efi-esrt
> @@ -35,10 +35,13 @@ What: /sys/firmware/efi/esrt/entries/entry$N/fw_type
> Date: February 2015
> Contact: Peter Jones <pjones at redhat.com>
> Description: What kind of firmware entry this is:
> - 0 - Unknown
> - 1 - System Firmware
> - 2 - Device Firmware
> - 3 - UEFI Driver
> +
> + == ===============
> + 0 Unknown
> + 1 System Firmware
> + 2 Device Firmware
> + 3 UEFI Driver
> + == ===============
>
> What: /sys/firmware/efi/esrt/entries/entry$N/fw_class
> Date: February 2015
> @@ -71,11 +74,14 @@ Date: February 2015
> Contact: Peter Jones <pjones at redhat.com>
> Description: The result of the last firmware update attempt for the
> firmware resource entry.
> - 0 - Success
> - 1 - Insufficient resources
> - 2 - Incorrect version
> - 3 - Invalid format
> - 4 - Authentication error
> - 5 - AC power event
> - 6 - Battery power event
> +
> + == ======================
> + 0 Success
> + 1 Insufficient resources
> + 2 Incorrect version
> + 3 Invalid format
> + 4 Authentication error
> + 5 AC power event
> + 6 Battery power event
> + == ======================
>
> diff --git a/Documentation/ABI/testing/sysfs-firmware-efi-runtime-map b/Documentation/ABI/testing/sysfs-firmware-efi-runtime-map
> index c61b9b348e99..9c4d581be396 100644
> --- a/Documentation/ABI/testing/sysfs-firmware-efi-runtime-map
> +++ b/Documentation/ABI/testing/sysfs-firmware-efi-runtime-map
> @@ -14,7 +14,7 @@ Description: Switching efi runtime services to virtual mode requires
> /sys/firmware/efi/runtime-map/ is the directory the kernel
> exports that information in.
>
> - subdirectories are named with the number of the memory range:
> + subdirectories are named with the number of the memory range::
>
> /sys/firmware/efi/runtime-map/0
> /sys/firmware/efi/runtime-map/1
> @@ -24,11 +24,13 @@ Description: Switching efi runtime services to virtual mode requires
>
> Each subdirectory contains five files:
>
> - attribute : The attributes of the memory range.
> - num_pages : The size of the memory range in pages.
> - phys_addr : The physical address of the memory range.
> - type : The type of the memory range.
> - virt_addr : The virtual address of the memory range.
> + ========= =========================================
> + attribute The attributes of the memory range.
> + num_pages The size of the memory range in pages.
> + phys_addr The physical address of the memory range.
> + type The type of the memory range.
> + virt_addr The virtual address of the memory range.
> + ========= =========================================
>
> Above values are all hexadecimal numbers with the '0x' prefix.
> Users: Kexec
> diff --git a/Documentation/ABI/testing/sysfs-firmware-qemu_fw_cfg b/Documentation/ABI/testing/sysfs-firmware-qemu_fw_cfg
> index 011dda4f8e8a..ee0d6dbc810e 100644
> --- a/Documentation/ABI/testing/sysfs-firmware-qemu_fw_cfg
> +++ b/Documentation/ABI/testing/sysfs-firmware-qemu_fw_cfg
> @@ -15,7 +15,7 @@ Description:
> to the fw_cfg device can be found in "docs/specs/fw_cfg.txt"
> in the QEMU source tree.
>
> - === SysFS fw_cfg Interface ===
> + **SysFS fw_cfg Interface**
>
> The fw_cfg sysfs interface described in this document is only
> intended to display discoverable blobs (i.e., those registered
> @@ -31,7 +31,7 @@ Description:
>
> /sys/firmware/qemu_fw_cfg/rev
>
> - --- Discoverable fw_cfg blobs by selector key ---
> + **Discoverable fw_cfg blobs by selector key**
>
> All discoverable blobs listed in the fw_cfg file directory are
> displayed as entries named after their unique selector key
> @@ -45,24 +45,26 @@ Description:
> Each such fw_cfg sysfs entry has the following values exported
> as attributes:
>
> - name : The 56-byte nul-terminated ASCII string used as the
> + ==== ====================================================
> + name The 56-byte nul-terminated ASCII string used as the
> blob's 'file name' in the fw_cfg directory.
> - size : The length of the blob, as given in the fw_cfg
> + size The length of the blob, as given in the fw_cfg
> directory.
> - key : The value of the blob's selector key as given in the
> + key The value of the blob's selector key as given in the
> fw_cfg directory. This value is the same as used in
> the parent directory name.
> - raw : The raw bytes of the blob, obtained by selecting the
> + raw The raw bytes of the blob, obtained by selecting the
> entry via the control register, and reading a number
> of bytes equal to the blob size from the data
> register.
> + ==== ====================================================
>
> - --- Listing fw_cfg blobs by file name ---
> + **Listing fw_cfg blobs by file name**
>
> While the fw_cfg device does not impose any specific naming
> convention on the blobs registered in the file directory,
> QEMU developers have traditionally used path name semantics
> - to give each blob a descriptive name. For example:
> + to give each blob a descriptive name. For example::
>
> "bootorder"
> "genroms/kvmvapic.bin"
> @@ -81,7 +83,7 @@ Description:
> of directories matching the path name components of fw_cfg
> blob names, ending in symlinks to the by_key entry for each
> "basename", as illustrated below (assume current directory is
> - /sys/firmware):
> + /sys/firmware)::
>
> qemu_fw_cfg/by_name/bootorder -> ../by_key/38
> qemu_fw_cfg/by_name/etc/e820 -> ../../by_key/35
> diff --git a/Documentation/ABI/testing/sysfs-firmware-sfi b/Documentation/ABI/testing/sysfs-firmware-sfi
> index 4be7d44aeacf..5210e0f06ddb 100644
> --- a/Documentation/ABI/testing/sysfs-firmware-sfi
> +++ b/Documentation/ABI/testing/sysfs-firmware-sfi
> @@ -9,7 +9,7 @@ Description:
> http://simplefirmware.org/documentation
>
> While the tables are used by the kernel, user-space
> - can observe them this way:
> + can observe them this way::
>
> - # cd /sys/firmware/sfi/tables
> - # cat $TABLENAME > $TABLENAME.bin
> + # cd /sys/firmware/sfi/tables
> + # cat $TABLENAME > $TABLENAME.bin
> diff --git a/Documentation/ABI/testing/sysfs-firmware-sgi_uv b/Documentation/ABI/testing/sysfs-firmware-sgi_uv
> index 4573fd4b7876..66800baab096 100644
> --- a/Documentation/ABI/testing/sysfs-firmware-sgi_uv
> +++ b/Documentation/ABI/testing/sysfs-firmware-sgi_uv
> @@ -5,7 +5,7 @@ Description:
> The /sys/firmware/sgi_uv directory contains information
> about the SGI UV platform.
>
> - Under that directory are a number of files:
> + Under that directory are a number of files::
>
> partition_id
> coherence_id
> @@ -14,7 +14,7 @@ Description:
> SGI UV systems can be partitioned into multiple physical
> machines, which each partition running a unique copy
> of the operating system. Each partition will have a unique
> - partition id. To display the partition id, use the command:
> + partition id. To display the partition id, use the command::
>
> cat /sys/firmware/sgi_uv/partition_id
>
> @@ -22,6 +22,6 @@ Description:
> A partitioned SGI UV system can have one or more coherence
> domain. The coherence id indicates which coherence domain
> this partition is in. To display the coherence id, use the
> - command:
> + command::
>
> cat /sys/firmware/sgi_uv/coherence_id
> diff --git a/Documentation/ABI/testing/sysfs-fs-f2fs b/Documentation/ABI/testing/sysfs-fs-f2fs
> index 834d0becae6d..67b3ed8e8c2f 100644
> --- a/Documentation/ABI/testing/sysfs-fs-f2fs
> +++ b/Documentation/ABI/testing/sysfs-fs-f2fs
> @@ -20,10 +20,13 @@ What: /sys/fs/f2fs/<disk>/gc_idle
> Date: July 2013
> Contact: "Namjae Jeon" <namjae.jeon at samsung.com>
> Description: Controls the victim selection policy for garbage collection.
> - Setting gc_idle = 0(default) will disable this option. Setting
> - gc_idle = 1 will select the Cost Benefit approach & setting
> - gc_idle = 2 will select the greedy approach & setting
> - gc_idle = 3 will select the age-threshold based approach.
> + Setting gc_idle = 0(default) will disable this option. Setting:
> +
> + =========== ===============================================
> + gc_idle = 1 will select the Cost Benefit approach & setting
> + gc_idle = 2 will select the greedy approach & setting
> + gc_idle = 3 will select the age-threshold based approach.
> + =========== ===============================================
>
> What: /sys/fs/f2fs/<disk>/reclaim_segments
> Date: October 2013
> @@ -46,10 +49,17 @@ Date: November 2013
> Contact: "Jaegeuk Kim" <jaegeuk.kim at samsung.com>
> Description: Controls the in-place-update policy.
> updates in f2fs. User can set:
> - 0x01: F2FS_IPU_FORCE, 0x02: F2FS_IPU_SSR,
> - 0x04: F2FS_IPU_UTIL, 0x08: F2FS_IPU_SSR_UTIL,
> - 0x10: F2FS_IPU_FSYNC, 0x20: F2FS_IPU_ASYNC,
> - 0x40: F2FS_IPU_NOCACHE.
> +
> + ==== =================
> + 0x01 F2FS_IPU_FORCE
> + 0x02 F2FS_IPU_SSR
> + 0x04 F2FS_IPU_UTIL
> + 0x08 F2FS_IPU_SSR_UTIL
> + 0x10 F2FS_IPU_FSYNC
> + 0x20 F2FS_IPU_ASYNC,
> + 0x40 F2FS_IPU_NOCACHE
> + ==== =================
> +
> Refer segment.h for details.
>
> What: /sys/fs/f2fs/<disk>/min_ipu_util
> @@ -332,18 +342,28 @@ Date: April 2020
> Contact: "Jaegeuk Kim" <jaegeuk at kernel.org>
> Description: Give a way to attach REQ_META|FUA to data writes
> given temperature-based bits. Now the bits indicate:
> - * REQ_META | REQ_FUA |
> - * 5 | 4 | 3 | 2 | 1 | 0 |
> - * Cold | Warm | Hot | Cold | Warm | Hot |
> +
> + +-------------------+-------------------+
> + | REQ_META | REQ_FUA |
> + +------+------+-----+------+------+-----+
> + | 5 | 4 | 3 | 2 | 1 | 0 |
> + +------+------+-----+------+------+-----+
> + | Cold | Warm | Hot | Cold | Warm | Hot |
> + +------+------+-----+------+------+-----+
>
> What: /sys/fs/f2fs/<disk>/node_io_flag
> Date: June 2020
> Contact: "Jaegeuk Kim" <jaegeuk at kernel.org>
> Description: Give a way to attach REQ_META|FUA to node writes
> given temperature-based bits. Now the bits indicate:
> - * REQ_META | REQ_FUA |
> - * 5 | 4 | 3 | 2 | 1 | 0 |
> - * Cold | Warm | Hot | Cold | Warm | Hot |
> +
> + +-------------------+-------------------+
> + | REQ_META | REQ_FUA |
> + +------+------+-----+------+------+-----+
> + | 5 | 4 | 3 | 2 | 1 | 0 |
> + +------+------+-----+------+------+-----+
> + | Cold | Warm | Hot | Cold | Warm | Hot |
> + +------+------+-----+------+------+-----+
>
> What: /sys/fs/f2fs/<disk>/iostat_period_ms
> Date: April 2020
> diff --git a/Documentation/ABI/testing/sysfs-kernel-mm-ksm b/Documentation/ABI/testing/sysfs-kernel-mm-ksm
> index dfc13244cda3..1c9bed5595f5 100644
> --- a/Documentation/ABI/testing/sysfs-kernel-mm-ksm
> +++ b/Documentation/ABI/testing/sysfs-kernel-mm-ksm
> @@ -34,8 +34,9 @@ Description: Kernel Samepage Merging daemon sysfs interface
> in a tree.
>
> run: write 0 to disable ksm, read 0 while ksm is disabled.
> - write 1 to run ksm, read 1 while ksm is running.
> - write 2 to disable ksm and unmerge all its pages.
> +
> + - write 1 to run ksm, read 1 while ksm is running.
> + - write 2 to disable ksm and unmerge all its pages.
>
> sleep_millisecs: how many milliseconds ksm should sleep between
> scans.
> diff --git a/Documentation/ABI/testing/sysfs-kernel-slab b/Documentation/ABI/testing/sysfs-kernel-slab
> index ed35833ad7f0..c9f12baf8baa 100644
> --- a/Documentation/ABI/testing/sysfs-kernel-slab
> +++ b/Documentation/ABI/testing/sysfs-kernel-slab
> @@ -346,6 +346,7 @@ Description:
> number of objects per slab. If a slab cannot be allocated
> because of fragmentation, SLUB will retry with the minimum order
> possible depending on its characteristics.
> +
> When debug_guardpage_minorder=N (N > 0) parameter is specified
> (see Documentation/admin-guide/kernel-parameters.rst), the minimum possible
> order is used and this sysfs entry can not be used to change
> @@ -361,6 +362,7 @@ Description:
> new slab has not been possible at the cache's order and instead
> fallen back to its minimum possible order. It can be written to
> clear the current count.
> +
> Available when CONFIG_SLUB_STATS is enabled.
>
> What: /sys/kernel/slab/cache/partial
> @@ -410,6 +412,7 @@ Description:
> slab from a remote node as opposed to allocating a new slab on
> the local node. This reduces the amount of wasted memory over
> the entire system but can be expensive.
> +
> Available when CONFIG_NUMA is enabled.
>
> What: /sys/kernel/slab/cache/sanity_checks
> diff --git a/Documentation/ABI/testing/sysfs-module b/Documentation/ABI/testing/sysfs-module
> index 0aac02e7fb0e..353c0db5bc1f 100644
> --- a/Documentation/ABI/testing/sysfs-module
> +++ b/Documentation/ABI/testing/sysfs-module
> @@ -17,14 +17,15 @@ KernelVersion: 3.1
> Contact: Kirill Smelkov <kirr at mns.spb.ru>
> Description: Maximum time allowed for periodic transfers per microframe (μs)
>
> - [ USB 2.0 sets maximum allowed time for periodic transfers per
> + Note:
> + USB 2.0 sets maximum allowed time for periodic transfers per
> microframe to be 80%, that is 100 microseconds out of 125
> microseconds (full microframe).
>
> However there are cases, when 80% max isochronous bandwidth is
> too limiting. For example two video streams could require 110
> microseconds of isochronous bandwidth per microframe to work
> - together. ]
> + together.
>
> Through this setting it is possible to raise the limit so that
> the host controller would allow allocating more than 100
> @@ -45,8 +46,10 @@ Date: Jan 2012
> KernelVersion:»·3.3
> Contact: Kay Sievers <kay.sievers at vrfy.org>
> Description: Module taint flags:
> - P - proprietary module
> - O - out-of-tree module
> - F - force-loaded module
> - C - staging driver module
> - E - unsigned module
> + == =====================
> + P proprietary module
> + O out-of-tree module
> + F force-loaded module
> + C staging driver module
> + E unsigned module
> + == =====================
> diff --git a/Documentation/ABI/testing/sysfs-platform-dell-laptop b/Documentation/ABI/testing/sysfs-platform-dell-laptop
> index 9b917c7453de..82bcfe9df66e 100644
> --- a/Documentation/ABI/testing/sysfs-platform-dell-laptop
> +++ b/Documentation/ABI/testing/sysfs-platform-dell-laptop
> @@ -34,9 +34,12 @@ Description:
> this file. To disable a trigger, write its name preceded
> by '-' instead.
>
> - For example, to enable the keyboard as trigger run:
> + For example, to enable the keyboard as trigger run::
> +
> echo +keyboard > /sys/class/leds/dell::kbd_backlight/start_triggers
> - To disable it:
> +
> + To disable it::
> +
> echo -keyboard > /sys/class/leds/dell::kbd_backlight/start_triggers
>
> Note that not all the available triggers can be configured.
> @@ -57,7 +60,8 @@ Description:
> with any the above units. If no unit is specified, the value
> is assumed to be expressed in seconds.
>
> - For example, to set the timeout to 10 minutes run:
> + For example, to set the timeout to 10 minutes run::
> +
> echo 10m > /sys/class/leds/dell::kbd_backlight/stop_timeout
>
> Note that when this file is read, the returned value might be
> diff --git a/Documentation/ABI/testing/sysfs-platform-dell-smbios b/Documentation/ABI/testing/sysfs-platform-dell-smbios
> index 205d3b6361e0..e6e0f7f834a7 100644
> --- a/Documentation/ABI/testing/sysfs-platform-dell-smbios
> +++ b/Documentation/ABI/testing/sysfs-platform-dell-smbios
> @@ -13,8 +13,8 @@ Description:
> For example the token ID "5" would be available
> as the following attributes:
>
> - 0005_location
> - 0005_value
> + - 0005_location
> + - 0005_value
>
> Tokens will vary from machine to machine, and
> only tokens available on that machine will be
> diff --git a/Documentation/ABI/testing/sysfs-platform-i2c-demux-pinctrl b/Documentation/ABI/testing/sysfs-platform-i2c-demux-pinctrl
> index c394b808be19..b6a138b50d99 100644
> --- a/Documentation/ABI/testing/sysfs-platform-i2c-demux-pinctrl
> +++ b/Documentation/ABI/testing/sysfs-platform-i2c-demux-pinctrl
> @@ -5,9 +5,9 @@ Contact: Wolfram Sang <wsa+renesas at sang-engineering.com>
> Description:
> Reading the file will give you a list of masters which can be
> selected for a demultiplexed bus. The format is
> - "<index>:<name>". Example from a Renesas Lager board:
> + "<index>:<name>". Example from a Renesas Lager board::
>
> - 0:/i2c at e6500000 1:/i2c at e6508000
> + 0:/i2c at e6500000 1:/i2c at e6508000
>
> What: /sys/devices/platform/<i2c-demux-name>/current_master
> Date: January 2016
> diff --git a/Documentation/ABI/testing/sysfs-platform-kim b/Documentation/ABI/testing/sysfs-platform-kim
> index c1653271872a..a7f81de68046 100644
> --- a/Documentation/ABI/testing/sysfs-platform-kim
> +++ b/Documentation/ABI/testing/sysfs-platform-kim
> @@ -5,6 +5,7 @@ Contact: "Pavan Savoy" <pavan_savoy at ti.com>
> Description:
> Name of the UART device at which the WL128x chip
> is connected. example: "/dev/ttyS0".
> +
> The device name flows down to architecture specific board
> initialization file from the SFI/ATAGS bootloader
> firmware. The name exposed is read from the user-space
> diff --git a/Documentation/ABI/testing/sysfs-platform-phy-rcar-gen3-usb2 b/Documentation/ABI/testing/sysfs-platform-phy-rcar-gen3-usb2
> index 6212697bbf6f..bc510ccc37a7 100644
> --- a/Documentation/ABI/testing/sysfs-platform-phy-rcar-gen3-usb2
> +++ b/Documentation/ABI/testing/sysfs-platform-phy-rcar-gen3-usb2
> @@ -7,9 +7,11 @@ Description:
> The file can show/change the phy mode for role swap of usb.
>
> Write the following strings to change the mode:
> - "host" - switching mode from peripheral to host.
> - "peripheral" - switching mode from host to peripheral.
> +
> + - "host" - switching mode from peripheral to host.
> + - "peripheral" - switching mode from host to peripheral.
>
> Read the file, then it shows the following strings:
> - "host" - The mode is host now.
> - "peripheral" - The mode is peripheral now.
> +
> + - "host" - The mode is host now.
> + - "peripheral" - The mode is peripheral now.
> diff --git a/Documentation/ABI/testing/sysfs-platform-renesas_usb3 b/Documentation/ABI/testing/sysfs-platform-renesas_usb3
> index 5621c15d5dc0..8af5b9c3fabb 100644
> --- a/Documentation/ABI/testing/sysfs-platform-renesas_usb3
> +++ b/Documentation/ABI/testing/sysfs-platform-renesas_usb3
> @@ -7,9 +7,11 @@ Description:
> The file can show/change the drd mode of usb.
>
> Write the following string to change the mode:
> - "host" - switching mode from peripheral to host.
> - "peripheral" - switching mode from host to peripheral.
> +
> + - "host" - switching mode from peripheral to host.
> + - "peripheral" - switching mode from host to peripheral.
>
> Read the file, then it shows the following strings:
> - "host" - The mode is host now.
> - "peripheral" - The mode is peripheral now.
> +
> + - "host" - The mode is host now.
> + - "peripheral" - The mode is peripheral now.
> diff --git a/Documentation/ABI/testing/sysfs-power b/Documentation/ABI/testing/sysfs-power
> index 5e6ead29124c..51c0f578bfce 100644
> --- a/Documentation/ABI/testing/sysfs-power
> +++ b/Documentation/ABI/testing/sysfs-power
> @@ -47,14 +47,18 @@ Description:
> suspend-to-disk mechanism. Reading from this file returns
> the name of the method by which the system will be put to
> sleep on the next suspend. There are four methods supported:
> +
> 'firmware' - means that the memory image will be saved to disk
> by some firmware, in which case we also assume that the
> firmware will handle the system suspend.
> +
> 'platform' - the memory image will be saved by the kernel and
> the system will be put to sleep by the platform driver (e.g.
> ACPI or other PM registers).
> +
> 'shutdown' - the memory image will be saved by the kernel and
> the system will be powered off.
> +
> 'reboot' - the memory image will be saved by the kernel and
> the system will be rebooted.
>
> @@ -74,12 +78,12 @@ Description:
> The suspend-to-disk method may be chosen by writing to this
> file one of the accepted strings:
>
> - 'firmware'
> - 'platform'
> - 'shutdown'
> - 'reboot'
> - 'testproc'
> - 'test'
> + - 'firmware'
> + - 'platform'
> + - 'shutdown'
> + - 'reboot'
> + - 'testproc'
> + - 'test'
>
> It will only change to 'firmware' or 'platform' if the system
> supports that.
> @@ -114,9 +118,9 @@ Description:
> string representing a nonzero integer into it.
>
> To use this debugging feature you should attempt to suspend
> - the machine, then reboot it and run
> + the machine, then reboot it and run::
>
> - dmesg -s 1000000 | grep 'hash matches'
> + dmesg -s 1000000 | grep 'hash matches'
>
> If you do not get any matches (or they appear to be false
> positives), it is possible that the last PM event point
> @@ -244,6 +248,7 @@ Description:
> wakeup sources created with the help of /sys/power/wake_lock.
> When a string is written to /sys/power/wake_unlock, it will be
> assumed to represent the name of a wakeup source to deactivate.
> +
> If a wakeup source object of that name exists and is active at
> the moment, it will be deactivated.
>
> diff --git a/Documentation/ABI/testing/sysfs-profiling b/Documentation/ABI/testing/sysfs-profiling
> index 8a8e466eb2c0..e39dd3a0ceef 100644
> --- a/Documentation/ABI/testing/sysfs-profiling
> +++ b/Documentation/ABI/testing/sysfs-profiling
> @@ -5,7 +5,7 @@ Description:
> /sys/kernel/profiling is the runtime equivalent
> of the boot-time profile= option.
>
> - You can get the same effect running:
> + You can get the same effect running::
>
> echo 2 > /sys/kernel/profiling
>
> diff --git a/Documentation/ABI/testing/sysfs-wusb_cbaf b/Documentation/ABI/testing/sysfs-wusb_cbaf
> index a99c5f86a37a..2969d3694ec0 100644
> --- a/Documentation/ABI/testing/sysfs-wusb_cbaf
> +++ b/Documentation/ABI/testing/sysfs-wusb_cbaf
> @@ -45,7 +45,8 @@ Description:
> 7. Device is unplugged.
>
> References:
> - [WUSB-AM] Association Models Supplement to the
> + [WUSB-AM]
> + Association Models Supplement to the
> Certified Wireless Universal Serial Bus
> Specification, version 1.0.
>
> diff --git a/Documentation/ABI/testing/usb-charger-uevent b/Documentation/ABI/testing/usb-charger-uevent
> index 419a92dd0d86..1db89b0cf80f 100644
> --- a/Documentation/ABI/testing/usb-charger-uevent
> +++ b/Documentation/ABI/testing/usb-charger-uevent
> @@ -3,44 +3,52 @@ Date: 2020-01-14
> KernelVersion: 5.6
> Contact: linux-usb at vger.kernel.org
> Description: There are two USB charger states:
> - USB_CHARGER_ABSENT
> - USB_CHARGER_PRESENT
> +
> + - USB_CHARGER_ABSENT
> + - USB_CHARGER_PRESENT
> +
> There are five USB charger types:
> - USB_CHARGER_UNKNOWN_TYPE: Charger type is unknown
> - USB_CHARGER_SDP_TYPE: Standard Downstream Port
> - USB_CHARGER_CDP_TYPE: Charging Downstream Port
> - USB_CHARGER_DCP_TYPE: Dedicated Charging Port
> - USB_CHARGER_ACA_TYPE: Accessory Charging Adapter
> +
> + ======================== ==========================
> + USB_CHARGER_UNKNOWN_TYPE Charger type is unknown
> + USB_CHARGER_SDP_TYPE Standard Downstream Port
> + USB_CHARGER_CDP_TYPE Charging Downstream Port
> + USB_CHARGER_DCP_TYPE Dedicated Charging Port
> + USB_CHARGER_ACA_TYPE Accessory Charging Adapter
> + ======================== ==========================
> +
> https://www.usb.org/document-library/battery-charging-v12-spec-and-adopters-agreement
>
> - Here are two examples taken using udevadm monitor -p when
> - USB charger is online:
> - UDEV change /devices/soc0/usbphynop1 (platform)
> - ACTION=change
> - DEVPATH=/devices/soc0/usbphynop1
> - DRIVER=usb_phy_generic
> - MODALIAS=of:Nusbphynop1T(null)Cusb-nop-xceiv
> - OF_COMPATIBLE_0=usb-nop-xceiv
> - OF_COMPATIBLE_N=1
> - OF_FULLNAME=/usbphynop1
> - OF_NAME=usbphynop1
> - SEQNUM=2493
> - SUBSYSTEM=platform
> - USB_CHARGER_STATE=USB_CHARGER_PRESENT
> - USB_CHARGER_TYPE=USB_CHARGER_SDP_TYPE
> - USEC_INITIALIZED=227422826
> + Here are two examples taken using ``udevadm monitor -p`` when
> + USB charger is online::
>
> - USB charger is offline:
> - KERNEL change /devices/soc0/usbphynop1 (platform)
> - ACTION=change
> - DEVPATH=/devices/soc0/usbphynop1
> - DRIVER=usb_phy_generic
> - MODALIAS=of:Nusbphynop1T(null)Cusb-nop-xceiv
> - OF_COMPATIBLE_0=usb-nop-xceiv
> - OF_COMPATIBLE_N=1
> - OF_FULLNAME=/usbphynop1
> - OF_NAME=usbphynop1
> - SEQNUM=2494
> - SUBSYSTEM=platform
> - USB_CHARGER_STATE=USB_CHARGER_ABSENT
> - USB_CHARGER_TYPE=USB_CHARGER_UNKNOWN_TYPE
> + UDEV change /devices/soc0/usbphynop1 (platform)
> + ACTION=change
> + DEVPATH=/devices/soc0/usbphynop1
> + DRIVER=usb_phy_generic
> + MODALIAS=of:Nusbphynop1T(null)Cusb-nop-xceiv
> + OF_COMPATIBLE_0=usb-nop-xceiv
> + OF_COMPATIBLE_N=1
> + OF_FULLNAME=/usbphynop1
> + OF_NAME=usbphynop1
> + SEQNUM=2493
> + SUBSYSTEM=platform
> + USB_CHARGER_STATE=USB_CHARGER_PRESENT
> + USB_CHARGER_TYPE=USB_CHARGER_SDP_TYPE
> + USEC_INITIALIZED=227422826
> +
> + USB charger is offline::
> +
> + KERNEL change /devices/soc0/usbphynop1 (platform)
> + ACTION=change
> + DEVPATH=/devices/soc0/usbphynop1
> + DRIVER=usb_phy_generic
> + MODALIAS=of:Nusbphynop1T(null)Cusb-nop-xceiv
> + OF_COMPATIBLE_0=usb-nop-xceiv
> + OF_COMPATIBLE_N=1
> + OF_FULLNAME=/usbphynop1
> + OF_NAME=usbphynop1
> + SEQNUM=2494
> + SUBSYSTEM=platform
> + USB_CHARGER_STATE=USB_CHARGER_ABSENT
> + USB_CHARGER_TYPE=USB_CHARGER_UNKNOWN_TYPE
> diff --git a/Documentation/ABI/testing/usb-uevent b/Documentation/ABI/testing/usb-uevent
> index d35c3cad892c..2b8eca4bf2b1 100644
> --- a/Documentation/ABI/testing/usb-uevent
> +++ b/Documentation/ABI/testing/usb-uevent
> @@ -6,22 +6,22 @@ Description: When the USB Host Controller has entered a state where it is no
> longer functional a uevent will be raised. The uevent will
> contain ACTION=offline and ERROR=DEAD.
>
> - Here is an example taken using udevadm monitor -p:
> + Here is an example taken using udevadm monitor -p::
>
> - KERNEL[130.428945] offline /devices/pci0000:00/0000:00:10.0/usb2 (usb)
> - ACTION=offline
> - BUSNUM=002
> - DEVNAME=/dev/bus/usb/002/001
> - DEVNUM=001
> - DEVPATH=/devices/pci0000:00/0000:00:10.0/usb2
> - DEVTYPE=usb_device
> - DRIVER=usb
> - ERROR=DEAD
> - MAJOR=189
> - MINOR=128
> - PRODUCT=1d6b/2/414
> - SEQNUM=2168
> - SUBSYSTEM=usb
> - TYPE=9/0/1
> + KERNEL[130.428945] offline /devices/pci0000:00/0000:00:10.0/usb2 (usb)
> + ACTION=offline
> + BUSNUM=002
> + DEVNAME=/dev/bus/usb/002/001
> + DEVNUM=001
> + DEVPATH=/devices/pci0000:00/0000:00:10.0/usb2
> + DEVTYPE=usb_device
> + DRIVER=usb
> + ERROR=DEAD
> + MAJOR=189
> + MINOR=128
> + PRODUCT=1d6b/2/414
> + SEQNUM=2168
> + SUBSYSTEM=usb
> + TYPE=9/0/1
>
> Users: chromium-os-dev at chromium.org
> diff --git a/scripts/get_abi.pl b/scripts/get_abi.pl
> index 413349789145..bdef3e5c35c7 100755
> --- a/scripts/get_abi.pl
> +++ b/scripts/get_abi.pl
> @@ -316,8 +316,6 @@ sub output_rest {
> $len = length($name) if (length($name) > $len);
> }
>
> - print "What:\n\n";
> -
> print "+-" . "-" x $len . "-+\n";
> foreach my $name (@names) {
> printf "| %s", $name . " " x ($len - length($name)) . " |\n";
> --
> 2.26.2
>
More information about the dri-devel
mailing list