[PATCH v3 6/6] drm/sprd: add Unisoc's drm mipi dsi&dphy driver
Kevin Tang
kevin3.tang at gmail.com
Thu Feb 11 09:02:30 UTC 2021
Daniel Vetter <daniel at ffwll.ch> 于2021年2月3日周三 下午10:37写道：
> On Tue, Jan 05, 2021 at 09:46:07PM +0800, Kevin Tang wrote:
> > Adds dsi host controller support for the Unisoc's display subsystem.
> > Adds dsi phy support for the Unisoc's display subsystem.
> > Only MIPI DSI Displays supported, DP/TV/HMDI will be support
> > in the feature.
> >
> > v1:
> > - Remove dphy and dsi graph binding, merge the dphy driver into the
> dsi.
> >
> > v2:
> > - Use drm_xxx to replace all DRM_XXX.
> > - Use kzalloc to replace devm_kzalloc for sprd_dsi structure init.
>
> Similar comments about kzalloc as with the previous sprd patch. Otherwise
> just two questions:
>
> dw-dsi is named at least like the synopsys driver we have already,
> wouldn't this fit into the drm/bridge driver we have? Ack from bridge
> people (just cc everyone for that dw_dsi driver to get their attention)
> would be good.
>
dw dsi controller is not a standard synopsys ip, we have updated a lot on
the basic ip version, the entire control register is different.
i think this is a good suggestion , i will cc to drm/bridge reviewers and
maintainers, thank you.
>
> Other thing is the header definitions for the registers. bitfields and
> unions are rather unusual for this, and to my understanding might blow up
> on different compilers. Results in rather verbose and unusual code, but
> since you only read/write full bytes at least it should be all save. Imo
> not a worry.
>
We have been using this way for many years and it seems that we haven’t
found any problems,
it does seem that there will be some unused bitfields, i don’t know if this
will be a problem...
>
> See below for the kzalloc comments.
>
Got it.
> -Daniel
>
> > ---
> > drivers/gpu/drm/sprd/Makefile | 7 +-
> > drivers/gpu/drm/sprd/dw_dsi_ctrl.c | 794 +++++++++++++++++
> > drivers/gpu/drm/sprd/dw_dsi_ctrl.h | 1475
> ++++++++++++++++++++++++++++++++
> > drivers/gpu/drm/sprd/dw_dsi_ctrl_ppi.c | 157 ++++
> > drivers/gpu/drm/sprd/dw_dsi_ctrl_ppi.h | 26 +
> > drivers/gpu/drm/sprd/megacores_pll.c | 317 +++++++
> > drivers/gpu/drm/sprd/megacores_pll.h | 146 ++++
> > drivers/gpu/drm/sprd/sprd_drm.c | 1 +
> > drivers/gpu/drm/sprd/sprd_drm.h | 1 +
> > drivers/gpu/drm/sprd/sprd_dsi.c | 1162 +++++++++++++++++++++++++
> > drivers/gpu/drm/sprd/sprd_dsi.h | 107 +++
> > 11 files changed, 4191 insertions(+), 2 deletions(-)
> > create mode 100644 drivers/gpu/drm/sprd/dw_dsi_ctrl.c
> > create mode 100644 drivers/gpu/drm/sprd/dw_dsi_ctrl.h
> > create mode 100644 drivers/gpu/drm/sprd/dw_dsi_ctrl_ppi.c
> > create mode 100644 drivers/gpu/drm/sprd/dw_dsi_ctrl_ppi.h
> > create mode 100644 drivers/gpu/drm/sprd/megacores_pll.c
> > create mode 100644 drivers/gpu/drm/sprd/megacores_pll.h
> > create mode 100644 drivers/gpu/drm/sprd/sprd_dsi.c
> > create mode 100644 drivers/gpu/drm/sprd/sprd_dsi.h
> >
> > diff --git a/drivers/gpu/drm/sprd/Makefile
> b/drivers/gpu/drm/sprd/Makefile
> > index 6c25bfa..d49f497 100644
> > --- a/drivers/gpu/drm/sprd/Makefile
> > +++ b/drivers/gpu/drm/sprd/Makefile
> > @@ -1,5 +1,8 @@
> > # SPDX-License-Identifier: GPL-2.0
> >
> > obj-y := sprd_drm.o \
> > - sprd_dpu.o
> > -
> > + sprd_dpu.o \
> > + sprd_dsi.o \
> > + dw_dsi_ctrl.o \
> > + dw_dsi_ctrl_ppi.o \
> > + megacores_pll.o
> > diff --git a/drivers/gpu/drm/sprd/dw_dsi_ctrl.c
> b/drivers/gpu/drm/sprd/dw_dsi_ctrl.c
> > new file mode 100644
> > index 0000000..1034aba
> > --- /dev/null
> > +++ b/drivers/gpu/drm/sprd/dw_dsi_ctrl.c
> > @@ -0,0 +1,794 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Copyright (C) 2020 Unisoc Inc.
> > + */
> > +
> > +#include <linux/io.h>
> > +#include <linux/init.h>
> > +#include <linux/delay.h>
> > +#include <linux/module.h>
> > +
> > +#include "dw_dsi_ctrl.h"
> > +
> > +/*
> > + * Modify power status of DSI Host core
> > + */
> > +void dsi_power_enable(struct dsi_context *ctx, int enable)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > +
> > + writel(enable, ®->SOFT_RESET);
> > +}
> > +/*
> > + * Enable/disable DPI video mode
> > + */
> > +void dsi_video_mode(struct dsi_context *ctx)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > +
> > + writel(0, ®->DSI_MODE_CFG);
> > +}
> > +/*
> > + * Enable command mode (Generic interface)
> > + */
> > +void dsi_cmd_mode(struct dsi_context *ctx)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > +
> > + writel(1, ®->DSI_MODE_CFG);
> > +}
> > +
> > +bool dsi_is_cmd_mode(struct dsi_context *ctx)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > +
> > + return readl(®->DSI_MODE_CFG);
> > +}
> > +/*
> > + * Configure the read back virtual channel for the generic interface
> > + */
> > +void dsi_rx_vcid(struct dsi_context *ctx, u8 vc)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x1C virtual_channel_id;
> > +
> > + virtual_channel_id.val = readl(®->VIRTUAL_CHANNEL_ID);
> > + virtual_channel_id.bits.gen_rx_vcid = vc;
> > +
> > + writel(virtual_channel_id.val, ®->VIRTUAL_CHANNEL_ID);
> > +}
> > +/*
> > + * Write the DPI video virtual channel destination
> > + */
> > +void dsi_video_vcid(struct dsi_context *ctx, u8 vc)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x1C virtual_channel_id;
> > +
> > + virtual_channel_id.val = readl(®->VIRTUAL_CHANNEL_ID);
> > + virtual_channel_id.bits.video_pkt_vcid = vc;
> > +
> > + writel(virtual_channel_id.val, ®->VIRTUAL_CHANNEL_ID);
> > +}
> > +/*
> > + * Set DPI video mode type (burst/non-burst - with sync pulses or
> events)
> > + */
> > +void dsi_dpi_video_burst_mode(struct dsi_context *ctx, int mode)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x38 vid_mode_cfg;
> > +
> > + vid_mode_cfg.val = readl(®->VID_MODE_CFG);
> > + vid_mode_cfg.bits.vid_mode_type = mode;
> > +
> > + writel(vid_mode_cfg.val, ®->VID_MODE_CFG);
> > +}
> > +/*
> > + * Set DPI video color coding
> > + */
> > +void dsi_dpi_color_coding(struct dsi_context *ctx, int coding)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x20 dpi_video_format;
> > +
> > + dpi_video_format.val = readl(®->DPI_VIDEO_FORMAT);
> > + dpi_video_format.bits.dpi_video_mode_format = coding;
> > +
> > + writel(dpi_video_format.val, ®->DPI_VIDEO_FORMAT);
> > +}
> > +/*
> > + * Configure the Horizontal Line time
> > + * param "byte_cycle" taken to transmit the total of the horizontal line
> > + */
> > +void dsi_dpi_hline_time(struct dsi_context *ctx, u16 byte_cycle)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x2C video_line_time;
> > +
> > + video_line_time.val = readl(®->VIDEO_LINE_TIME);
> > + video_line_time.bits.video_line_time = byte_cycle;
> > +
> > + writel(video_line_time.val, ®->VIDEO_LINE_TIME);
> > +}
> > +/*
> > + * Configure the Horizontal back porch time
> > + * param "byte_cycle" taken to transmit the horizontal back porch
> > + */
> > +void dsi_dpi_hbp_time(struct dsi_context *ctx, u16 byte_cycle)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x28 video_line_hblk_time;
> > +
> > + video_line_hblk_time.val = readl(®->VIDEO_LINE_HBLK_TIME);
> > + video_line_hblk_time.bits.video_line_hbp_time = byte_cycle;
> > +
> > + writel(video_line_hblk_time.val, ®->VIDEO_LINE_HBLK_TIME);
> > +}
> > +/*
> > + * Configure the Horizontal sync time,
> > + * param "byte_cycle" taken to transmit the horizontal sync
> > + */
> > +void dsi_dpi_hsync_time(struct dsi_context *ctx, u16 byte_cycle)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x28 video_line_hblk_time;
> > +
> > + video_line_hblk_time.val = readl(®->VIDEO_LINE_HBLK_TIME);
> > + video_line_hblk_time.bits.video_line_hsa_time = byte_cycle;
> > +
> > + writel(video_line_hblk_time.val, ®->VIDEO_LINE_HBLK_TIME);
> > +}
> > +/*
> > + * Configure the vertical active lines of the video stream
> > + */
> > +void dsi_dpi_vact(struct dsi_context *ctx, u16 lines)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x34 video_active_lines;
> > +
> > + video_active_lines.val = readl(®->VIDEO_VACTIVE_LINES);
> > + video_active_lines.bits.vactive_lines = lines;
> > +
> > + writel(video_active_lines.val, ®->VIDEO_VACTIVE_LINES);
> > +}
> > +
> > +void dsi_dpi_vfp(struct dsi_context *ctx, u16 lines)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x30 video_vblk_lines;
> > +
> > + video_vblk_lines.val = readl(®->VIDEO_VBLK_LINES);
> > + video_vblk_lines.bits.vfp_lines = lines;
> > +
> > + writel(video_vblk_lines.val, ®->VIDEO_VBLK_LINES);
> > +}
> > +
> > +void dsi_dpi_vbp(struct dsi_context *ctx, u16 lines)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x30 video_vblk_lines;
> > +
> > + video_vblk_lines.val = readl(®->VIDEO_VBLK_LINES);
> > + video_vblk_lines.bits.vbp_lines = lines;
> > +
> > + writel(video_vblk_lines.val, ®->VIDEO_VBLK_LINES);
> > +}
> > +
> > +void dsi_dpi_vsync(struct dsi_context *ctx, u16 lines)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x30 video_vblk_lines;
> > +
> > + video_vblk_lines.val = readl(®->VIDEO_VBLK_LINES);
> > + video_vblk_lines.bits.vsa_lines = lines;
> > +
> > + writel(video_vblk_lines.val, ®->VIDEO_VBLK_LINES);
> > +}
> > +
> > +void dsi_dpi_hporch_lp_en(struct dsi_context *ctx, int enable)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x38 vid_mode_cfg;
> > +
> > + vid_mode_cfg.val = readl(®->VID_MODE_CFG);
> > +
> > + vid_mode_cfg.bits.lp_hfp_en = enable;
> > + vid_mode_cfg.bits.lp_hbp_en = enable;
> > +
> > + writel(vid_mode_cfg.val, ®->VID_MODE_CFG);
> > +}
> > +/*
> > + * Enable return to low power mode inside vertical active lines periods
> when
> > + * timing allows
> > + */
> > +void dsi_dpi_vporch_lp_en(struct dsi_context *ctx, int enable)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x38 vid_mode_cfg;
> > +
> > + vid_mode_cfg.val = readl(®->VID_MODE_CFG);
> > +
> > + vid_mode_cfg.bits.lp_vact_en = enable;
> > + vid_mode_cfg.bits.lp_vfp_en = enable;
> > + vid_mode_cfg.bits.lp_vbp_en = enable;
> > + vid_mode_cfg.bits.lp_vsa_en = enable;
> > +
> > + writel(vid_mode_cfg.val, ®->VID_MODE_CFG);
> > +}
> > +/*
> > + * Enable FRAME BTA ACK
> > + */
> > +void dsi_dpi_frame_ack_en(struct dsi_context *ctx, int enable)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x38 vid_mode_cfg;
> > +
> > + vid_mode_cfg.val = readl(®->VID_MODE_CFG);
> > + vid_mode_cfg.bits.frame_bta_ack_en = enable;
> > +
> > + writel(vid_mode_cfg.val, ®->VID_MODE_CFG);
> > +}
> > +/*
> > + * Write no of chunks to core - taken into consideration only when
> multi packet
> > + * is enabled
> > + */
> > +void dsi_dpi_chunk_num(struct dsi_context *ctx, u16 num)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x24 video_pkt_config;
> > +
> > + video_pkt_config.val = readl(®->VIDEO_PKT_CONFIG);
> > + video_pkt_config.bits.video_line_chunk_num = num;
> > +
> > + writel(video_pkt_config.val, ®->VIDEO_PKT_CONFIG);
> > +}
> > +/*
> > + * Write the null packet size - will only be taken into account when
> null
> > + * packets are enabled.
> > + */
> > +void dsi_dpi_null_packet_size(struct dsi_context *ctx, u16 size)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0xC0 video_nullpkt_size;
> > +
> > + video_nullpkt_size.val = readl(®->VIDEO_NULLPKT_SIZE);
> > + video_nullpkt_size.bits.video_nullpkt_size = size;
> > +
> > + writel(video_nullpkt_size.val, ®->VIDEO_NULLPKT_SIZE);
> > +}
> > +/*
> > + * Write video packet size. obligatory for sending video
> > + */
> > +void dsi_dpi_video_packet_size(struct dsi_context *ctx, u16 size)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x24 video_pkt_config;
> > +
> > + video_pkt_config.val = readl(®->VIDEO_PKT_CONFIG);
> > + video_pkt_config.bits.video_pkt_size = size;
> > +
> > + writel(video_pkt_config.val, ®->VIDEO_PKT_CONFIG);
> > +}
> > +/*
> > + * Specifiy the size of the packet memory write start/continue
> > + */
> > +void dsi_edpi_max_pkt_size(struct dsi_context *ctx, u16 size)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0xC4 dcs_wm_pkt_size;
> > +
> > + dcs_wm_pkt_size.val = readl(®->DCS_WM_PKT_SIZE);
> > + dcs_wm_pkt_size.bits.dcs_wm_pkt_size = size;
> > +
> > + writel(dcs_wm_pkt_size.val, ®->DCS_WM_PKT_SIZE);
> > +}
> > +/*
> > + * Enable tear effect acknowledge
> > + */
> > +void dsi_tear_effect_ack_en(struct dsi_context *ctx, int enable)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x68 cmd_mode_cfg;
> > +
> > + cmd_mode_cfg.val = readl(®->CMD_MODE_CFG);
> > + cmd_mode_cfg.bits.tear_fx_en = enable;
> > +
> > + writel(cmd_mode_cfg.val, ®->CMD_MODE_CFG);
> > +}
> > +/*
> > + * Set DCS command packet transmission to transmission type
> > + */
> > +void dsi_cmd_mode_lp_cmd_en(struct dsi_context *ctx, int enable)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x68 cmd_mode_cfg;
> > +
> > + cmd_mode_cfg.val = readl(®->CMD_MODE_CFG);
> > +
> > + cmd_mode_cfg.bits.gen_sw_0p_tx = enable;
> > + cmd_mode_cfg.bits.gen_sw_1p_tx = enable;
> > + cmd_mode_cfg.bits.gen_sw_2p_tx = enable;
> > + cmd_mode_cfg.bits.gen_lw_tx = enable;
> > + cmd_mode_cfg.bits.dcs_sw_0p_tx = enable;
> > + cmd_mode_cfg.bits.dcs_sw_1p_tx = enable;
> > + cmd_mode_cfg.bits.dcs_lw_tx = enable;
> > + cmd_mode_cfg.bits.max_rd_pkt_size = enable;
> > +
> > + cmd_mode_cfg.bits.gen_sr_0p_tx = enable;
> > + cmd_mode_cfg.bits.gen_sr_1p_tx = enable;
> > + cmd_mode_cfg.bits.gen_sr_2p_tx = enable;
> > + cmd_mode_cfg.bits.dcs_sr_0p_tx = enable;
> > +
> > + writel(cmd_mode_cfg.val, ®->CMD_MODE_CFG);
> > +}
> > +/*
> > + * Set DCS read command packet transmission to transmission type
> > + */
> > +void dsi_video_mode_lp_cmd_en(struct dsi_context *ctx, int enable)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x38 vid_mode_cfg;
> > +
> > + vid_mode_cfg.val = readl(®->VID_MODE_CFG);
> > + vid_mode_cfg.bits.lp_cmd_en = enable;
> > +
> > + writel(vid_mode_cfg.val, ®->VID_MODE_CFG);
> > +}
> > +
> > +/*
> > + * Write command header in the generic interface (which also sends DCS
> commands) as a subset
> > + */
> > +void dsi_set_packet_header(struct dsi_context *ctx,
> > + u8 vc,
> > + u8 type,
> > + u8 wc_lsb,
> > + u8 wc_msb)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x6C gen_hdr;
> > +
> > + gen_hdr.bits.gen_dt = type;
> > + gen_hdr.bits.gen_vc = vc;
> > + gen_hdr.bits.gen_wc_lsbyte = wc_lsb;
> > + gen_hdr.bits.gen_wc_msbyte = wc_msb;
> > +
> > + writel(gen_hdr.val, ®->GEN_HDR);
> > +}
> > +/*
> > + * Write the payload of the long packet commands
> > + */
> > +void dsi_set_packet_payload(struct dsi_context *ctx, u32 payload)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > +
> > + writel(payload, ®->GEN_PLD_DATA);
> > +}
> > +/*
> > + * Read the payload of the long packet commands
> > + */
> > +u32 dsi_get_rx_payload(struct dsi_context *ctx)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > +
> > + return readl(®->GEN_PLD_DATA);
> > +}
> > +
> > +/*
> > + * Enable Bus Turn-around request
> > + */
> > +void dsi_bta_en(struct dsi_context *ctx, int enable)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > +
> > + writel(enable, ®->TA_EN);
> > +}
> > +/*
> > + * Enable EOTp reception
> > + */
> > +void dsi_eotp_rx_en(struct dsi_context *ctx, int enable)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0xBC eotp_en;
> > +
> > + eotp_en.val = readl(®->EOTP_EN);
> > + eotp_en.bits.rx_eotp_en = enable;
> > +
> > + writel(eotp_en.val, ®->EOTP_EN);
> > +}
> > +/*
> > + * Enable EOTp transmission
> > + */
> > +void dsi_eotp_tx_en(struct dsi_context *ctx, int enable)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0xBC eotp_en;
> > +
> > + eotp_en.val = readl(®->EOTP_EN);
> > + eotp_en.bits.tx_eotp_en = enable;
> > +
> > + writel(eotp_en.val, ®->EOTP_EN);
> > +}
> > +/*
> > + * Enable ECC reception, error correction and reporting
> > + */
> > +void dsi_ecc_rx_en(struct dsi_context *ctx, int enable)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0xB4 rx_pkt_check_config;
> > +
> > + rx_pkt_check_config.val = readl(®->RX_PKT_CHECK_CONFIG);
> > + rx_pkt_check_config.bits.rx_pkt_ecc_en = enable;
> > +
> > + writel(rx_pkt_check_config.val, ®->RX_PKT_CHECK_CONFIG);
> > +}
> > +/*
> > + * Enable CRC reception, error reporting
> > + */
> > +void dsi_crc_rx_en(struct dsi_context *ctx, int enable)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0xB4 rx_pkt_check_config;
> > +
> > + rx_pkt_check_config.val = readl(®->RX_PKT_CHECK_CONFIG);
> > + rx_pkt_check_config.bits.rx_pkt_crc_en = enable;
> > +
> > + writel(rx_pkt_check_config.val, ®->RX_PKT_CHECK_CONFIG);
> > +}
> > +/*
> > + * Get status of read command
> > + */
> > +bool dsi_is_bta_returned(struct dsi_context *ctx)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x98 cmd_mode_status;
> > +
> > + cmd_mode_status.val = readl(®->CMD_MODE_STATUS);
> > +
> > + return cmd_mode_status.bits.gen_cmd_rdcmd_done;
> > +}
> > +/*
> > + * Get the FULL status of generic read payload fifo
> > + */
> > +bool dsi_is_rx_payload_fifo_full(struct dsi_context *ctx)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x98 cmd_mode_status;
> > +
> > + cmd_mode_status.val = readl(®->CMD_MODE_STATUS);
> > +
> > + return cmd_mode_status.bits.gen_cmd_rdata_fifo_full;
> > +}
> > +/*
> > + * Get the EMPTY status of generic read payload fifo
> > + */
> > +bool dsi_is_rx_payload_fifo_empty(struct dsi_context *ctx)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x98 cmd_mode_status;
> > +
> > + cmd_mode_status.val = readl(®->CMD_MODE_STATUS);
> > +
> > + return cmd_mode_status.bits.gen_cmd_rdata_fifo_empty;
> > +}
> > +/*
> > + * Get the FULL status of generic write payload fifo
> > + */
> > +bool dsi_is_tx_payload_fifo_full(struct dsi_context *ctx)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x98 cmd_mode_status;
> > +
> > + cmd_mode_status.val = readl(®->CMD_MODE_STATUS);
> > +
> > + return cmd_mode_status.bits.gen_cmd_wdata_fifo_full;
> > +}
> > +/*
> > + * Get the EMPTY status of generic write payload fifo
> > + */
> > +bool dsi_is_tx_payload_fifo_empty(struct dsi_context *ctx)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x98 cmd_mode_status;
> > +
> > + cmd_mode_status.val = readl(®->CMD_MODE_STATUS);
> > +
> > + return cmd_mode_status.bits.gen_cmd_wdata_fifo_empty;
> > +}
> > +/*
> > + * Get the EMPTY status of generic command fifo
> > + */
> > +bool dsi_is_tx_cmd_fifo_empty(struct dsi_context *ctx)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x98 cmd_mode_status;
> > +
> > + cmd_mode_status.val = readl(®->CMD_MODE_STATUS);
> > +
> > + return cmd_mode_status.bits.gen_cmd_cmd_fifo_empty;
> > +}
> > +/*
> > + * DPI interface signal delay config
> > + * param byte_cycle period for waiting after controller receiving HSYNC
> from
> > + * DPI interface to start read pixel data from memory.
> > + */
> > +void dsi_dpi_sig_delay(struct dsi_context *ctx, u16 byte_cycle)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0xD0 video_sig_delay_config;
> > +
> > + video_sig_delay_config.val = readl(®->VIDEO_SIG_DELAY_CONFIG);
> > + video_sig_delay_config.bits.video_sig_delay = byte_cycle;
> > +
> > + writel(video_sig_delay_config.val, ®->VIDEO_SIG_DELAY_CONFIG);
> > +}
> > +/*
> > + * Configure how many cycles of byte clock would the PHY module take
> > + * to switch data lane from high speed to low power
> > + */
> > +void dsi_datalane_hs2lp_config(struct dsi_context *ctx, u16 byte_cycle)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0xAC phy_datalane_time_config;
> > +
> > + phy_datalane_time_config.val =
> readl(®->PHY_DATALANE_TIME_CONFIG);
> > + phy_datalane_time_config.bits.phy_datalane_hs_to_lp_time =
> byte_cycle;
> > +
> > + writel(phy_datalane_time_config.val,
> ®->PHY_DATALANE_TIME_CONFIG);
> > +}
> > +/*
> > + * Configure how many cycles of byte clock would the PHY module take
> > + * to switch the data lane from to low power high speed
> > + */
> > +void dsi_datalane_lp2hs_config(struct dsi_context *ctx, u16 byte_cycle)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0xAC phy_datalane_time_config;
> > +
> > + phy_datalane_time_config.val =
> readl(®->PHY_DATALANE_TIME_CONFIG);
> > + phy_datalane_time_config.bits.phy_datalane_lp_to_hs_time =
> byte_cycle;
> > +
> > + writel(phy_datalane_time_config.val,
> ®->PHY_DATALANE_TIME_CONFIG);
> > +}
> > +/*
> > + * Configure how many cycles of byte clock would the PHY module take
> > + * to switch clock lane from high speed to low power
> > + */
> > +void dsi_clklane_hs2lp_config(struct dsi_context *ctx, u16 byte_cycle)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0xA8 phy_clklane_time_config;
> > +
> > + phy_clklane_time_config.val = readl(®->PHY_CLKLANE_TIME_CONFIG);
> > + phy_clklane_time_config.bits.phy_clklane_hs_to_lp_time =
> byte_cycle;
> > +
> > + writel(phy_clklane_time_config.val, ®->PHY_CLKLANE_TIME_CONFIG);
> > +}
> > +/*
> > + * Configure how many cycles of byte clock would the PHY module take
> > + * to switch clock lane from to low power high speed
> > + */
> > +void dsi_clklane_lp2hs_config(struct dsi_context *ctx, u16 byte_cycle)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0xA8 phy_clklane_time_config;
> > +
> > + phy_clklane_time_config.val = readl(®->PHY_CLKLANE_TIME_CONFIG);
> > + phy_clklane_time_config.bits.phy_clklane_lp_to_hs_time =
> byte_cycle;
> > +
> > + writel(phy_clklane_time_config.val, ®->PHY_CLKLANE_TIME_CONFIG);
> > +}
> > +/*
> > + * Configure how many cycles of byte clock would the PHY module take
> > + * to turn the bus around to start receiving
> > + */
> > +void dsi_max_read_time(struct dsi_context *ctx, u16 byte_cycle)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > +
> > + writel(byte_cycle, ®->MAX_READ_TIME);
> > +}
> > +/*
> > + * Enable the automatic mechanism to stop providing clock in the clock
> > + * lane when time allows
> > + */
> > +void dsi_nc_clk_en(struct dsi_context *ctx, int enable)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x74 phy_clk_lane_lp_ctrl;
> > +
> > + phy_clk_lane_lp_ctrl.val = readl(®->PHY_CLK_LANE_LP_CTRL);
> > + phy_clk_lane_lp_ctrl.bits.auto_clklane_ctrl_en = enable;
> > +
> > + writel(phy_clk_lane_lp_ctrl.val, ®->PHY_CLK_LANE_LP_CTRL);
> > +}
> > +/*
> > + * Write transmission escape timeout
> > + * a safe guard so that the state machine would reset if transmission
> > + * takes too long
> > + */
> > +void dsi_tx_escape_division(struct dsi_context *ctx, u8 div)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > +
> > + writel(div, ®->TX_ESC_CLK_CONFIG);
> > +}
> > +/*
> > + * Configure timeout divisions (so they would have more clock ticks)
> > + * div no of hs cycles before transiting back to LP in
> > + * (lane_clk / div)
> > + */
> > +void dsi_timeout_clock_division(struct dsi_context *ctx, u8 div)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > +
> > + writel(div, ®->TIMEOUT_CNT_CLK_CONFIG);
> > +}
> > +/*
> > + * Configure the Low power receive time out
> > + */
> > +void dsi_lp_rx_timeout(struct dsi_context *ctx, u16 byte_cycle)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > +
> > + writel(byte_cycle, ®->LRX_H_TO_CONFIG);
> > +}
> > +/*
> > + * Configure a high speed transmission time out
> > + */
> > +void dsi_hs_tx_timeout(struct dsi_context *ctx, u16 byte_cycle)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > +
> > + writel(byte_cycle, ®->HTX_TO_CONFIG);
> > +}
> > +/*
> > + * Get the error 0 interrupt register status
> > + */
> > +u32 dsi_int0_status(struct dsi_context *ctx)
> > +{
> > + struct sprd_dsi *dsi = container_of(ctx, struct sprd_dsi, ctx);
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x08 protocol_int_sts;
> > +
> > + protocol_int_sts.val = readl(®->PROTOCOL_INT_STS);
> > + writel(protocol_int_sts.val, ®->PROTOCOL_INT_CLR);
> > +
> > + if (protocol_int_sts.bits.dphy_errors_0)
> > + drm_err(dsi->drm, "dphy_err: escape entry error\n");
> > +
> > + if (protocol_int_sts.bits.dphy_errors_1)
> > + drm_err(dsi->drm, "dphy_err: lp data transmission sync
> error\n");
> > +
> > + if (protocol_int_sts.bits.dphy_errors_2)
> > + drm_err(dsi->drm, "dphy_err: control error\n");
> > +
> > + if (protocol_int_sts.bits.dphy_errors_3)
> > + drm_err(dsi->drm, "dphy_err: LP0 contention error\n");
> > +
> > + if (protocol_int_sts.bits.dphy_errors_4)
> > + drm_err(dsi->drm, "dphy_err: LP1 contention error\n");
> > +
> > + if (protocol_int_sts.bits.ack_with_err_0)
> > + drm_err(dsi->drm, "ack_err: SoT error\n");
> > +
> > + if (protocol_int_sts.bits.ack_with_err_1)
> > + drm_err(dsi->drm, "ack_err: SoT Sync error\n");
> > +
> > + if (protocol_int_sts.bits.ack_with_err_2)
> > + drm_err(dsi->drm, "ack_err: EoT Sync error\n");
> > +
> > + if (protocol_int_sts.bits.ack_with_err_3)
> > + drm_err(dsi->drm, "ack_err: Escape Mode Entry Command
> error\n");
> > +
> > + if (protocol_int_sts.bits.ack_with_err_4)
> > + drm_err(dsi->drm, "ack_err: LP Transmit Sync error\n");
> > +
> > + if (protocol_int_sts.bits.ack_with_err_5)
> > + drm_err(dsi->drm, "ack_err: Peripheral Timeout error\n");
> > +
> > + if (protocol_int_sts.bits.ack_with_err_6)
> > + drm_err(dsi->drm, "ack_err: False Control error\n");
> > +
> > + if (protocol_int_sts.bits.ack_with_err_7)
> > + drm_err(dsi->drm, "ack_err: reserved (specific to
> device)\n");
> > +
> > + if (protocol_int_sts.bits.ack_with_err_8)
> > + drm_err(dsi->drm, "ack_err: ECC error, single-bit
> (corrected)\n");
> > +
> > + if (protocol_int_sts.bits.ack_with_err_9)
> > + drm_err(dsi->drm, "ack_err: ECC error, multi-bit (not
> corrected)\n");
> > +
> > + if (protocol_int_sts.bits.ack_with_err_10)
> > + drm_err(dsi->drm, "ack_err: checksum error (long packet
> only)\n");
> > +
> > + if (protocol_int_sts.bits.ack_with_err_11)
> > + drm_err(dsi->drm, "ack_err: not recognized DSI data
> type\n");
> > +
> > + if (protocol_int_sts.bits.ack_with_err_12)
> > + drm_err(dsi->drm, "ack_err: DSI VC ID Invalid\n");
> > +
> > + if (protocol_int_sts.bits.ack_with_err_13)
> > + drm_err(dsi->drm, "ack_err: invalid transmission
> length\n");
> > +
> > + if (protocol_int_sts.bits.ack_with_err_14)
> > + drm_err(dsi->drm, "ack_err: reserved (specific to
> device)\n");
> > +
> > + if (protocol_int_sts.bits.ack_with_err_15)
> > + drm_err(dsi->drm, "ack_err: DSI protocol violation\n");
> > +
> > + return 0;
> > +}
> > +/*
> > + * Get the error 1 interrupt register status
> > + */
> > +u32 dsi_int1_status(struct dsi_context *ctx)
> > +{
> > + struct sprd_dsi *dsi = container_of(ctx, struct sprd_dsi, ctx);
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x10 internal_int_sts;
> > + u32 status = 0;
> > +
> > + internal_int_sts.val = readl(®->INTERNAL_INT_STS);
> > + writel(internal_int_sts.val, ®->INTERNAL_INT_CLR);
> > +
> > + if (internal_int_sts.bits.receive_pkt_size_err)
> > + drm_err(dsi->drm, "receive packet size error\n");
> > +
> > + if (internal_int_sts.bits.eotp_not_receive_err)
> > + drm_err(dsi->drm, "EoTp packet is not received\n");
> > +
> > + if (internal_int_sts.bits.gen_cmd_cmd_fifo_wr_err)
> > + drm_err(dsi->drm, "cmd header-fifo is full\n");
> > +
> > + if (internal_int_sts.bits.gen_cmd_rdata_fifo_rd_err)
> > + drm_err(dsi->drm, "cmd read-payload-fifo is empty\n");
> > +
> > + if (internal_int_sts.bits.gen_cmd_rdata_fifo_wr_err)
> > + drm_err(dsi->drm, "cmd read-payload-fifo is full\n");
> > +
> > + if (internal_int_sts.bits.gen_cmd_wdata_fifo_wr_err)
> > + drm_err(dsi->drm, "cmd write-payload-fifo is full\n");
> > +
> > + if (internal_int_sts.bits.gen_cmd_wdata_fifo_rd_err)
> > + drm_err(dsi->drm, "cmd write-payload-fifo is empty\n");
> > +
> > + if (internal_int_sts.bits.dpi_pix_fifo_wr_err) {
> > + drm_err(dsi->drm, "DPI pixel-fifo is full\n");
> > + status |= DSI_INT_STS_NEED_SOFT_RESET;
> > + }
> > +
> > + if (internal_int_sts.bits.ecc_single_err)
> > + drm_err(dsi->drm, "ECC single error in a received
> packet\n");
> > +
> > + if (internal_int_sts.bits.ecc_multi_err)
> > + drm_err(dsi->drm, "ECC multiple error in a received
> packet\n");
> > +
> > + if (internal_int_sts.bits.crc_err)
> > + drm_err(dsi->drm, "CRC error in the received packet
> payload\n");
> > +
> > + if (internal_int_sts.bits.hs_tx_timeout)
> > + drm_err(dsi->drm, "high-speed transmission timeout\n");
> > +
> > + if (internal_int_sts.bits.lp_rx_timeout)
> > + drm_err(dsi->drm, "low-power reception timeout\n");
> > +
> > + return status;
> > +}
> > +/*
> > + * Configure MASK (hiding) of interrupts coming from error 0 source
> > + */
> > +void dsi_int0_mask(struct dsi_context *ctx, u32 mask)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > +
> > + writel(mask, ®->MASK_PROTOCOL_INT);
> > +}
> > +/*
> > + * Configure MASK (hiding) of interrupts coming from error 1 source
> > + */
> > +void dsi_int1_mask(struct dsi_context *ctx, u32 mask)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > +
> > + writel(mask, ®->MASK_INTERNAL_INT);
> > +}
> > diff --git a/drivers/gpu/drm/sprd/dw_dsi_ctrl.h
> b/drivers/gpu/drm/sprd/dw_dsi_ctrl.h
> > new file mode 100644
> > index 0000000..ffba621
> > --- /dev/null
> > +++ b/drivers/gpu/drm/sprd/dw_dsi_ctrl.h
> > @@ -0,0 +1,1475 @@
> > +/* SPDX-License-Identifier: GPL-2.0 */
> > +/*
> > + * Copyright (C) 2020 Unisoc Inc.
> > + */
> > +
> > +#ifndef _DW_DSI_CTRL_H_
> > +#define _DW_DSI_CTRL_H_
> > +
> > +#include <asm/types.h>
> > +
> > +#include "sprd_dsi.h"
> > +
> > +struct dsi_reg {
> > + union _0x00 {
> > + u32 val;
> > + struct _DSI_VERSION {
> > + u32 dsi_version: 16;
> > + u32 reserved: 16;
> > + } bits;
> > + } DSI_VERSION;
> > +
> > + union _0x04 {
> > + u32 val;
> > + struct _SOFT_RESET {
> > + /*
> > + * This bit configures the core either to work normal or to
> > + * reset. It's default value is 0. After the core configur-
> > + * ation, to enable the mipi_dsi_host, set this register
> to 1.
> > + * 1: power up 0: reset core
> > + */
> > + u32 dsi_soft_reset: 1;
> > +
> > + u32 reserved: 31;
> > + } bits;
> > + } SOFT_RESET;
> > +
> > + union _0x08 {
> > + u32 val;
> > + struct _PROTOCOL_INT_STS {
> > + /* ErrEsc escape entry error from Lane 0 */
> > + u32 dphy_errors_0: 1;
> > +
> > + /* ErrSyncEsc low-power data transmission synchronization
> > + * error from Lane 0
> > + */
> > + u32 dphy_errors_1: 1;
> > +
> > + /* ErrControl error from Lane 0 */
> > + u32 dphy_errors_2: 1;
> > +
> > + /* ErrContentionLP0 LP0 contention error from Lane 0 */
> > + u32 dphy_errors_3: 1;
> > +
> > + /* ErrContentionLP1 LP1 contention error from Lane 0 */
> > + u32 dphy_errors_4: 1;
> > +
> > + /* debug mode protocol errors */
> > + u32 protocol_debug_err: 11;
> > +
> > + /* SoT error from the Acknowledge error report */
> > + u32 ack_with_err_0: 1;
> > +
> > + /* SoT Sync error from the Acknowledge error report */
> > + u32 ack_with_err_1: 1;
> > +
> > + /* EoT Sync error from the Acknowledge error report */
> > + u32 ack_with_err_2: 1;
> > +
> > + /* Escape Mode Entry Command error from the Acknowledge
> > + * error report
> > + */
> > + u32 ack_with_err_3: 1;
> > +
> > + /* LP Transmit Sync error from the Acknowledge error
> report */
> > + u32 ack_with_err_4: 1;
> > +
> > + /* Peripheral Timeout error from the Acknowledge error
> report */
> > + u32 ack_with_err_5: 1;
> > +
> > + /* False Control error from the Acknowledge error report */
> > + u32 ack_with_err_6: 1;
> > +
> > + /* reserved (specific to device) from the Acknowledge error
> > + * report
> > + */
> > + u32 ack_with_err_7: 1;
> > +
> > + /* ECC error, single-bit (detected and corrected) from the
> > + * Acknowledge error report
> > + */
> > + u32 ack_with_err_8: 1;
> > +
> > + /* ECC error, multi-bit (detected, not corrected) from the
> > + * Acknowledge error report
> > + */
> > + u32 ack_with_err_9: 1;
> > +
> > + /* checksum error (long packet only) from the Acknowledge
> > + * error report
> > + */
> > + u32 ack_with_err_10: 1;
> > +
> > + /* not recognized DSI data type from the Acknowledge error
> > + * report
> > + */
> > + u32 ack_with_err_11: 1;
> > +
> > + /* DSI VC ID Invalid from the Acknowledge error report */
> > + u32 ack_with_err_12: 1;
> > +
> > + /* invalid transmission length from the Acknowledge error
> > + * report
> > + */
> > + u32 ack_with_err_13: 1;
> > +
> > + /* reserved (specific to device) from the Acknowledge error
> > + * report
> > + */
> > + u32 ack_with_err_14: 1;
> > +
> > + /* DSI protocol violation from the Acknowledge error
> report */
> > + u32 ack_with_err_15: 1;
> > +
> > + } bits;
> > + } PROTOCOL_INT_STS;
> > +
> > + union _0x0C {
> > + u32 val;
> > + struct _MASK_PROTOCOL_INT {
> > + u32 mask_dphy_errors_0: 1;
> > + u32 mask_dphy_errors_1: 1;
> > + u32 mask_dphy_errors_2: 1;
> > + u32 mask_dphy_errors_3: 1;
> > + u32 mask_dphy_errors_4: 1;
> > + u32 mask_protocol_debug_err: 11;
> > + u32 mask_ack_with_err_0: 1;
> > + u32 mask_ack_with_err_1: 1;
> > + u32 mask_ack_with_err_2: 1;
> > + u32 mask_ack_with_err_3: 1;
> > + u32 mask_ack_with_err_4: 1;
> > + u32 mask_ack_with_err_5: 1;
> > + u32 mask_ack_with_err_6: 1;
> > + u32 mask_ack_with_err_7: 1;
> > + u32 mask_ack_with_err_8: 1;
> > + u32 mask_ack_with_err_9: 1;
> > + u32 mask_ack_with_err_10: 1;
> > + u32 mask_ack_with_err_11: 1;
> > + u32 mask_ack_with_err_12: 1;
> > + u32 mask_ack_with_err_13: 1;
> > + u32 mask_ack_with_err_14: 1;
> > + u32 mask_ack_with_err_15: 1;
> > + } bits;
> > + } MASK_PROTOCOL_INT;
> > +
> > + union _0x10 {
> > + u32 val;
> > + struct _INTERNAL_INT_STS {
> > + /* This bit indicates that the packet size error is
> detected
> > + * during the packet reception.
> > + */
> > + u32 receive_pkt_size_err: 1;
> > +
> > + /* This bit indicates that the EoTp packet is not received
> at
> > + * the end of the incoming peripheral transmission
> > + */
> > + u32 eotp_not_receive_err: 1;
> > +
> > + /* This bit indicates that the system tried to write a
> command
> > + * through the Generic interface and the FIFO is full.
> There-
> > + * fore, the command is not written.
> > + */
> > + u32 gen_cmd_cmd_fifo_wr_err: 1;
> > +
> > + /* This bit indicates that during a DCS read data, the
> payload
> > + * FIFO becomes empty and the data sent to the interface is
> > + * corrupted.
> > + */
> > + u32 gen_cmd_rdata_fifo_rd_err: 1;
> > +
> > + /* This bit indicates that during a generic interface
> packet
> > + * read back, the payload FIFO becomes full and the
> received
> > + * data is corrupted.
> > + */
> > + u32 gen_cmd_rdata_fifo_wr_err: 1;
> > +
> > + /* This bit indicates that the system tried to write a
> payload
> > + * data through the Generic interface and the FIFO is full.
> > + * Therefore, the payload is not written.
> > + */
> > + u32 gen_cmd_wdata_fifo_wr_err: 1;
> > +
> > + /* This bit indicates that during a Generic interface
> packet
> > + * build, the payload FIFO becomes empty and corrupt data
> is
> > + * sent.
> > + */
> > + u32 gen_cmd_wdata_fifo_rd_err: 1;
> > +
> > + /* This bit indicates that during a DPI pixel line storage,
> > + * the payload FIFO becomes full and the data stored is
> > + * corrupted.
> > + */
> > + u32 dpi_pix_fifo_wr_err: 1;
> > +
> > + /* internal debug error */
> > + u32 internal_debug_err: 19;
> > +
> > + /* This bit indicates that the ECC single error is detected
> > + * and corrected in a received packet.
> > + */
> > + u32 ecc_single_err: 1;
> > +
> > + /* This bit indicates that the ECC multiple error is
> detected
> > + * in a received packet.
> > + */
> > + u32 ecc_multi_err: 1;
> > +
> > + /* This bit indicates that the CRC error is detected in the
> > + * received packet payload.
> > + */
> > + u32 crc_err: 1;
> > +
> > + /* This bit indicates that the high-speed transmission
> timeout
> > + * counter reached the end and contention is detected.
> > + */
> > + u32 hs_tx_timeout: 1;
> > +
> > + /* This bit indicates that the low-power reception timeout
> > + * counter reached the end and contention is detected.
> > + */
> > + u32 lp_rx_timeout: 1;
> > +
> > + } bits;
> > + } INTERNAL_INT_STS;
> > +
> > + union _0x14 {
> > + u32 val;
> > + struct _MASK_INTERNAL_INT {
> > + u32 mask_receive_pkt_size_err: 1;
> > + u32 mask_eopt_not_receive_err: 1;
> > + u32 mask_gen_cmd_cmd_fifo_wr_err: 1;
> > + u32 mask_gen_cmd_rdata_fifo_rd_err: 1;
> > + u32 mask_gen_cmd_rdata_fifo_wr_err: 1;
> > + u32 mask_gen_cmd_wdata_fifo_wr_err: 1;
> > + u32 mask_gen_cmd_wdata_fifo_rd_err: 1;
> > + u32 mask_dpi_pix_fifo_wr_err: 1;
> > + u32 mask_internal_debug_err: 19;
> > + u32 mask_ecc_single_err: 1;
> > + u32 mask_ecc_multi_err: 1;
> > + u32 mask_crc_err: 1;
> > + u32 mask_hs_tx_timeout: 1;
> > + u32 mask_lp_rx_timeout: 1;
> > + } bits;
> > + } MASK_INTERNAL_INT;
> > +
> > + union _0x18 {
> > + u32 val;
> > + struct _DSI_MODE_CFG {
> > + /* This bit configures the operation mode
> > + * 0: Video mode ; 1: Command mode
> > + */
> > + u32 cmd_video_mode: 1;
> > +
> > + u32 reserved: 31;
> > +
> > + } bits;
> > + } DSI_MODE_CFG;
> > +
> > + union _0x1C {
> > + u32 val;
> > + struct _VIRTUAL_CHANNEL_ID {
> > + /* This field indicates the Generic interface read-back
> > + * virtual channel identification
> > + */
> > + u32 gen_rx_vcid: 2;
> > +
> > + /* This field configures the DPI virtual channel id that
> > + * is indexed to the VIDEO mode packets
> > + */
> > + u32 video_pkt_vcid: 2;
> > +
> > + u32 reserved: 28;
> > +
> > + } bits;
> > + } VIRTUAL_CHANNEL_ID;
> > +
> > + union _0x20 {
> > + u32 val;
> > + struct _DPI_VIDEO_FORMAT {
> > + /*
> > + * This field configures the DPI color coding as follows:
> > + * 0000: 16-bit configuration 1
> > + * 0001: 16-bit configuration 2
> > + * 0010: 16-bit configuration 3
> > + * 0011: 18-bit configuration 1
> > + * 0100: 18-bit configuration 2
> > + * 0101: 24-bit
> > + * 0110: 20-bit YCbCr 4:2:2 loosely packed
> > + * 0111: 24-bit YCbCr 4:2:2
> > + * 1000: 16-bit YCbCr 4:2:2
> > + * 1001: 30-bit
> > + * 1010: 36-bit
> > + * 1011: 12-bit YCbCr 4:2:0
> > + * 1100: Compression Display Stream
> > + * 1101-1111: 12-bit YCbCr 4:2:0
> > + */
> > + u32 dpi_video_mode_format: 6;
> > +
> > + /* When set to 1, this bit activates loosely packed
> > + * variant to 18-bit configurations
> > + */
> > + u32 loosely18_en: 1;
> > +
> > + u32 reserved: 25;
> > +
> > + } bits;
> > + } DPI_VIDEO_FORMAT;
> > +
> > + union _0x24 {
> > + u32 val;
> > + struct _VIDEO_PKT_CONFIG {
> > + /*
> > + * This field configures the number of pixels in a single
> > + * video packet. For 18-bit not loosely packed data types,
> > + * this number must be a multiple of 4. For YCbCr data
> > + * types, it must be a multiple of 2, as described in the
> > + * DSI specification.
> > + */
> > + u32 video_pkt_size: 16;
> > +
> > + /*
> > + * This register configures the number of chunks to be
> > + * transmitted during a Line period (a chunk consists of
> > + * a video packet and a null packet). If set to 0 or 1,
> > + * the video line is transmitted in a single packet. If
> > + * set to 1, the packet is part of a chunk, so a null
> packet
> > + * follows it if vid_null_size > 0. Otherwise, multiple
> chunks
> > + * are used to transmit each video line.
> > + */
> > + u32 video_line_chunk_num: 16;
> > +
> > + } bits;
> > + } VIDEO_PKT_CONFIG;
> > +
> > + union _0x28 {
> > + u32 val;
> > + struct _VIDEO_LINE_HBLK_TIME {
> > + /* This field configures the Horizontal Back Porch period
> > + * in lane byte clock cycles
> > + */
> > + u32 video_line_hbp_time: 16;
> > +
> > + /* This field configures the Horizontal Synchronism Active
> > + * period in lane byte clock cycles
> > + */
> > + u32 video_line_hsa_time: 16;
> > +
> > + } bits;
> > + } VIDEO_LINE_HBLK_TIME;
> > +
> > + union _0x2C {
> > + u32 val;
> > + struct _VIDEO_LINE_TIME {
> > + /* This field configures the size of the total line time
> > + * (HSA+HBP+HACT+HFP) counted in lane byte clock cycles
> > + */
> > + u32 video_line_time: 16;
> > +
> > + u32 reserved: 16;
> > +
> > + } bits;
> > + } VIDEO_LINE_TIME;
> > +
> > + union _0x30 {
> > + u32 val;
> > + struct _VIDEO_VBLK_LINES {
> > + /* This field configures the Vertical Front Porch period
> > + * measured in number of horizontal lines
> > + */
> > + u32 vfp_lines: 10;
> > +
> > + /* This field configures the Vertical Back Porch period
> > + * measured in number of horizontal lines
> > + */
> > + u32 vbp_lines: 10;
> > +
> > + /* This field configures the Vertical Synchronism Active
> > + * period measured in number of horizontal lines
> > + */
> > + u32 vsa_lines: 10;
> > +
> > + u32 reserved: 2;
> > +
> > + } bits;
> > + } VIDEO_VBLK_LINES;
> > +
> > + union _0x34 {
> > + u32 val;
> > + struct _VIDEO_VACTIVE_LINES {
> > + /* This field configures the Vertical Active period
> measured
> > + * in number of horizontal lines
> > + */
> > + u32 vactive_lines: 14;
> > +
> > + u32 reserved: 18;
> > +
> > + } bits;
> > + } VIDEO_VACTIVE_LINES;
> > +
> > + union _0x38 {
> > + u32 val;
> > + struct _VID_MODE_CFG {
> > + /*
> > + * This field indicates the video mode transmission type as
> > + * follows:
> > + * 00: Non-burst with sync pulses
> > + * 01: Non-burst with sync events
> > + * 10 and 11: Burst mode
> > + */
> > + u32 vid_mode_type: 2;
> > +
> > + u32 reserved_0: 6;
> > +
> > + /* When set to 1, this bit enables the return to low-power
> > + * inside the VSA period when timing allows.
> > + */
> > + u32 lp_vsa_en: 1;
> > +
> > + /* When set to 1, this bit enables the return to low-power
> > + * inside the VBP period when timing allows.
> > + */
> > + u32 lp_vbp_en: 1;
> > +
> > + /* When set to 1, this bit enables the return to low-power
> > + * inside the VFP period when timing allows.
> > + */
> > + u32 lp_vfp_en: 1;
> > +
> > + /* When set to 1, this bit enables the return to low-power
> > + * inside the VACT period when timing allows.
> > + */
> > + u32 lp_vact_en: 1;
> > +
> > + /* When set to 1, this bit enables the return to low-power
> > + * inside the HBP period when timing allows.
> > + */
> > + u32 lp_hbp_en: 1;
> > +
> > + /* When set to 1, this bit enables the return to low-power
> > + * inside the HFP period when timing allows.
> > + */
> > + u32 lp_hfp_en: 1;
> > +
> > + /* When set to 1, this bit enables the request for an ack-
> > + * nowledge response at the end of a frame.
> > + */
> > + u32 frame_bta_ack_en: 1;
> > +
> > + /* When set to 1, this bit enables the command transmission
> > + * only in low-power mode.
> > + */
> > + u32 lp_cmd_en: 1;
> > +
> > + u32 reserved_1: 16;
> > +
> > + } bits;
> > + } VID_MODE_CFG;
> > +
> > + union _0x3C {
> > + u32 val;
> > + struct _SDF_MODE_CONFIG {
> > + /*
> > + * This field defines the 3D mode on/off & display
> orientation:
> > + * 00: 3D mode off (2D mode on)
> > + * 01: 3D mode on, portrait orientation
> > + * 10: 3D mode on, landscape orientation
> > + * 11: Reserved
> > + */
> > + u32 rf_3d_mode: 2;
> > +
> > + /*
> > + * This field defines the 3D image format:
> > + * 00: Line (alternating lines of left and right data)
> > + * 01: Frame (alternating frames of left and right data)
> > + * 10: Pixel (alternating pixels of left and right data)
> > + * 11: Reserved
> > + */
> > + u32 rf_3d_format: 2;
> > +
> > + /*
> > + * This field defines whether there is a second VSYNC pulse
> > + * between Left and Right Images, when 3D Image Format is
> > + * Frame-based:
> > + * 0: No sync pulses between left and right data
> > + * 1: Sync pulse (HSYNC, VSYNC, blanking) between left and
> > + * right data
> > + */
> > + u32 second_vsync_en: 1;
> > +
> > + /*
> > + * This bit defines the left or right order:
> > + * 0: Left eye data is sent first, and then the right eye
> data
> > + * is sent.
> > + * 1: Right eye data is sent first, and then the left eye
> data
> > + * is sent.
> > + */
> > + u32 left_right_order: 1;
> > +
> > + u32 reserved_0: 2;
> > +
> > + /*
> > + * When set, causes the next VSS packet to include 3D
> control
> > + * payload in every VSS packet.
> > + */
> > + u32 rf_3d_payload_en: 1;
> > +
> > + u32 reserved_1: 23;
> > +
> > + } bits;
> > + } SDF_MODE_CONFIG;
> > +
> > + union _0x40 {
> > + u32 val;
> > + struct _TIMEOUT_CNT_CLK_CONFIG {
> > + /*
> > + * This field indicates the division factor for the Time
> Out
> > + * clock used as the timing unit in the configuration of
> HS to
> > + * LP and LP to HS transition error.
> > + */
> > + u32 timeout_cnt_clk_config: 16;
> > +
> > + u32 reserved: 16;
> > +
> > + } bits;
> > + } TIMEOUT_CNT_CLK_CONFIG;
> > +
> > + union _0x44 {
> > + u32 val;
> > + struct _HTX_TO_CONFIG {
> > + /*
> > + * This field configures the timeout counter that triggers
> > + * a high speed transmission timeout contention detection
> > + * (measured in TO_CLK_DIVISION cycles).
> > + *
> > + * If using the non-burst mode and there is no sufficient
> > + * time to switch from HS to LP and back in the period
> which
> > + * is from one line data finishing to the next line sync
> > + * start, the DSI link returns the LP state once per frame,
> > + * then you should configure the TO_CLK_DIVISION and
> > + * hstx_to_cnt to be in accordance with:
> > + * hstx_to_cnt * lanebyteclkperiod * TO_CLK_DIVISION >= the
> > + * time of one FRAME data transmission * (1 + 10%)
> > + *
> > + * In burst mode, RGB pixel packets are time-compressed,
> > + * leaving more time during a scan line. Therefore, if in
> > + * burst mode and there is sufficient time to switch from
> HS
> > + * to LP and back in the period of time from one line data
> > + * finishing to the next line sync start, the DSI link can
> > + * return LP mode and back in this time interval to save
> power.
> > + * For this, configure the TO_CLK_DIVISION and hstx_to_cnt
> > + * to be in accordance with:
> > + * hstx_to_cnt * lanebyteclkperiod * TO_CLK_DIVISION >= the
> > + * time of one LINE data transmission * (1 + 10%)
> > + */
> > + u32 htx_to_cnt_limit: 32;
> > + } bits;
> > + } HTX_TO_CONFIG;
> > +
> > + union _0x48 {
> > + u32 val;
> > + struct _LRX_H_TO_CONFIG {
> > + /*
> > + * This field configures the timeout counter that triggers
> > + * a low-power reception timeout contention detection
> (measured
> > + * in TO_CLK_DIVISION cycles).
> > + */
> > + u32 lrx_h_to_cnt_limit: 32;
> > + } bits;
> > + } LRX_H_TO_CONFIG;
> > +
> > + union _0x4C {
> > + u32 val;
> > + struct _RD_PRESP_TO_CONFIG {
> > + /*
> > + * This field sets a period for which the DWC_mipi_dsi_host
> > + * keeps the link still, after sending a low-power read
> oper-
> > + * ation. This period is measured in cycles of lanebyteclk.
> > + * The counting starts when the D-PHY enters the Stop state
> > + * and causes no interrupts.
> > + */
> > + u32 lprd_presp_to_cnt_limit: 16;
> > +
> > + /*
> > + * This field sets a period for which the DWC_mipi_dsi_host
> > + * keeps the link still, after sending a high-speed read
> oper-
> > + * ation. This period is measured in cycles of lanebyteclk.
> > + * The counting starts when the D-PHY enters the Stop state
> > + * and causes no interrupts.
> > + */
> > + u32 hsrd_presp_to_cnt_limit: 16;
> > +
> > + } bits;
> > + } RD_PRESP_TO_CONFIG;
> > +
> > + union _0x50 {
> > + u32 val;
> > + struct _HSWR_PRESP_TO_CONFIG {
> > + /*
> > + * This field sets a period for which the DWC_mipi_dsi_host
> > + * keeps the link inactive after sending a high-speed write
> > + * operation. This period is measured in cycles of
> lanebyteclk.
> > + * The counting starts when the D-PHY enters the Stop state
> > + * and causes no interrupts.
> > + */
> > + u32 hswr_presp_to_cnt_limit: 16;
> > +
> > + u32 reserved_0: 8;
> > +
> > + /*
> > + * When set to 1, this bit ensures that the peripheral
> response
> > + * timeout caused by hs_wr_to_cnt is used only once per
> eDPI
> > + * frame, when both the following conditions are met:
> > + * dpivsync_edpiwms has risen and fallen.
> > + * Packets originated from eDPI have been transmitted and
> its
> > + * FIFO is empty again In this scenario no non-eDPI
> requests
> > + * are sent to the D-PHY, even if there is traffic from
> generic
> > + * or DBI ready to be sent, making it return to stop state.
> > + * When it does so, PRESP_TO counter is activated and only
> when
> > + * it finishes does the controller send any other traffic
> that
> > + * is ready.
> > + */
> > + u32 hswr_presp_to_mode: 1;
> > +
> > + u32 reserved_1: 7;
> > +
> > + } bits;
> > + } HSWR_PRESP_TO_CONFIG;
> > +
> > + union _0x54 {
> > + u32 val;
> > + struct _LPWR_PRESP_TO_CONFIG {
> > + /*
> > + * This field sets a period for which the DWC_mipi_dsi_host
> > + * keeps the link still, after sending a low-power write
> oper-
> > + * ation. This period is measured in cycles of lanebyteclk.
> > + * The counting starts when the D-PHY enters the Stop state
> > + * and causes no interrupts.
> > + */
> > + u32 lpwr_presp_to_cnt_limit: 16;
> > +
> > + u32 reserved: 16;
> > +
> > + } bits;
> > + } LPWR_PRESP_TO_CONFIG;
> > +
> > + union _0x58 {
> > + u32 val;
> > + struct _BTA_PRESP_TO_CONFIG {
> > + /*
> > + * This field sets a period for which the DWC_mipi_dsi_host
> > + * keeps the link still, after completing a Bus
> Turn-Around.
> > + * This period is measured in cycles of lanebyteclk. The
> > + * counting starts when the D-PHY enters the Stop state and
> > + * causes no interrupts.
> > + */
> > + u32 bta_presp_to_cnt_limit: 16;
> > +
> > + u32 reserved: 16;
> > +
> > + } bits;
> > + } BTA_PRESP_TO_CONFIG;
> > +
> > + union _0x5C {
> > + u32 val;
> > + struct _TX_ESC_CLK_CONFIG {
> > + /*
> > + * This field indicates the division factor for the TX
> Escape
> > + * clock source (lanebyteclk). The values 0 and 1 stop the
> > + * TX_ESC clock generation.
> > + */
> > + u32 tx_esc_clk_config: 16;
> > +
> > + u32 reserved: 16;
> > +
> > + } bits;
> > + } TX_ESC_CLK_CONFIG;
> > +
> > + union _0x60 {
> > + u32 val;
> > + struct _VACT_CMD_TRANS_LIMIT {
> > + /*
> > + * This field is used for the transmission of commands in
> > + * low-power mode. It defines the size, in bytes, of the
> > + * largest packet that can fit in a line during the VACT
> > + * region.
> > + */
> > + u32 vact_cmd_trans_limit: 8;
> > +
> > + u32 reserved: 24;
> > +
> > + } bits;
> > + } VACT_CMD_TRANS_LIMIT;
> > +
> > + union _0x64 {
> > + u32 val;
> > + struct _VBLK_CMD_TRANS_LIMIT {
> > + /*
> > + * This field is used for the transmission of commands in
> > + * low-power mode. It defines the size, in bytes, of the
> > + * largest packet that can fit in a line during the VSA,
> VBP,
> > + * and VFP regions.
> > + */
> > + u32 vblk_cmd_trans_limit: 8;
> > +
> > + u32 reserved: 24;
> > +
> > + } bits;
> > + } VBLK_CMD_TRANS_LIMIT;
> > +
> > + union _0x68 {
> > + u32 val;
> > + struct _CMD_MODE_CFG {
> > + /*
> > + * When set to 1, this bit enables the tearing effect
> > + * acknowledge request.
> > + */
> > + u32 tear_fx_en: 1;
> > +
> > + /*
> > + * When set to 1, this bit enables the acknowledge request
> > + * after each packet transmission.
> > + */
> > + u32 ack_rqst_en: 1;
> > +
> > + u32 reserved_0: 3;
> > +
> > + u32 pps_tx: 1;
> > + u32 exq_tx: 1;
> > + u32 cmc_tx: 1;
> > +
> > + /*
> > + * This bit configures the Generic short write packet with
> > + * zero parameter command transmission type:
> > + * 0: High-speed 1: Low-power
> > + */
> > + u32 gen_sw_0p_tx: 1;
> > +
> > + /*
> > + * This bit configures the Generic short write packet with
> > + * one parameter command transmission type:
> > + * 0: High-speed 1: Low-power
> > + */
> > + u32 gen_sw_1p_tx: 1;
> > +
> > + /*
> > + * This bit configures the Generic short write packet with
> > + * two parameters command transmission type:
> > + * 0: High-speed 1: Low-power
> > + */
> > + u32 gen_sw_2p_tx: 1;
> > +
> > + /*
> > + * This bit configures the Generic short read packet with
> > + * zero parameter command transmission type:
> > + * 0: High-speed 1: Low-power
> > + */
> > + u32 gen_sr_0p_tx: 1;
> > +
> > + /*
> > + * This bit configures the Generic short read packet with
> > + * one parameter command transmission type:
> > + * 0: High-speed 1: Low-power
> > + */
> > + u32 gen_sr_1p_tx: 1;
> > +
> > + /*
> > + * This bit configures the Generic short read packet with
> > + * two parameters command transmission type:
> > + * 0: High-speed 1: Low-power
> > + */
> > + u32 gen_sr_2p_tx: 1;
> > +
> > + /*
> > + * This bit configures the Generic long write packet
> command
> > + * transmission type:
> > + * 0: High-speed 1: Low-power
> > + */
> > + u32 gen_lw_tx: 1;
> > +
> > + u32 reserved_1: 1;
> > +
> > + /*
> > + * This bit configures the DCS short write packet with zero
> > + * parameter command transmission type:
> > + * 0: High-speed 1: Low-power
> > + */
> > + u32 dcs_sw_0p_tx: 1;
> > +
> > + /*
> > + * This bit configures the DCS short write packet with one
> > + * parameter command transmission type:
> > + * 0: High-speed 1: Low-power
> > + */
> > + u32 dcs_sw_1p_tx: 1;
> > +
> > + /*
> > + * This bit configures the DCS short read packet with zero
> > + * parameter command transmission type:
> > + * 0: High-speed 1: Low-power
> > + */
> > + u32 dcs_sr_0p_tx: 1;
> > +
> > + /*
> > + * This bit configures the DCS long write packet command
> > + * transmission type:
> > + * 0: High-speed 1: Low-power
> > + */
> > + u32 dcs_lw_tx: 1;
> > +
> > + u32 reserved_2: 4;
> > +
> > + /*
> > + * This bit configures the maximum read packet size command
> > + * transmission type:
> > + * 0: High-speed 1: Low-power
> > + */
> > + u32 max_rd_pkt_size: 1;
> > +
> > + u32 reserved_3: 7;
> > +
> > + } bits;
> > + } CMD_MODE_CFG;
> > +
> > + union _0x6C {
> > + u32 val;
> > + struct _GEN_HDR {
> > + /*
> > + * This field configures the packet data type of the header
> > + * packet.
> > + */
> > + u32 gen_dt: 6;
> > +
> > + /*
> > + * This field configures the virtual channel id of the
> header
> > + * packet.
> > + */
> > + u32 gen_vc: 2;
> > +
> > + /*
> > + * This field configures the least significant byte of the
> > + * header packet's Word count for long packets or data 0
> for
> > + * short packets.
> > + */
> > + u32 gen_wc_lsbyte: 8;
> > +
> > + /*
> > + * This field configures the most significant byte of the
> > + * header packet's word count for long packets or data 1
> for
> > + * short packets.
> > + */
> > + u32 gen_wc_msbyte: 8;
> > +
> > + u32 reserved: 8;
> > +
> > + } bits;
> > + } GEN_HDR;
> > +
> > + union _0x70 {
> > + u32 val;
> > + struct _GEN_PLD_DATA {
> > + /* This field indicates byte 1 of the packet payload. */
> > + u32 gen_pld_b1: 8;
> > +
> > + /* This field indicates byte 2 of the packet payload. */
> > + u32 gen_pld_b2: 8;
> > +
> > + /* This field indicates byte 3 of the packet payload. */
> > + u32 gen_pld_b3: 8;
> > +
> > + /* This field indicates byte 4 of the packet payload. */
> > + u32 gen_pld_b4: 8;
> > +
> > + } bits;
> > + } GEN_PLD_DATA;
> > +
> > + union _0x74 {
> > + u32 val;
> > + struct _PHY_CLK_LANE_LP_CTRL {
> > + /* This bit controls the D-PHY PPI txrequestclkhs signal */
> > + u32 phy_clklane_tx_req_hs: 1;
> > +
> > + /* This bit enables the automatic mechanism to stop
> providing
> > + * clock in the clock lane when time allows.
> > + */
> > + u32 auto_clklane_ctrl_en: 1;
> > +
> > + u32 reserved: 30;
> > + } bits;
> > + } PHY_CLK_LANE_LP_CTRL;
> > +
> > + union _0x78 {
> > + u32 val;
> > + struct _PHY_INTERFACE_CTRL {
> > + /* When set to 0, this bit places the D-PHY macro in power-
> > + * down state.
> > + */
> > + u32 rf_phy_shutdown: 1;
> > +
> > + /* When set to 0, this bit places the digital section of
> the
> > + * D-PHY in the reset state.
> > + */
> > + u32 rf_phy_reset_n: 1;
> > +
> > + /* When set to 1, this bit enables the D-PHY Clock Lane
> > + * module.
> > + */
> > + u32 rf_phy_clk_en: 1;
> > +
> > + /* When the D-PHY is in ULPS, this bit enables the D-PHY
> PLL. */
> > + u32 rf_phy_force_pll: 1;
> > +
> > + /* ULPS mode Request on clock lane */
> > + u32 rf_phy_clk_txrequlps: 1;
> > +
> > + /* ULPS mode Exit on clock lane */
> > + u32 rf_phy_clk_txexitulps: 1;
> > +
> > + /* ULPS mode Request on all active data lanes */
> > + u32 rf_phy_data_txrequlps: 1;
> > +
> > + /* ULPS mode Exit on all active data lanes */
> > + u32 rf_phy_data_txexitulps: 1;
> > +
> > + u32 reserved: 24;
> > + } bits;
> > + } PHY_INTERFACE_CTRL;
> > +
> > + union _0x7C {
> > + u32 val;
> > + struct _PHY_TX_TRIGGERS {
> > + /* This field controls the trigger transmissions. */
> > + u32 phy_tx_triggers: 4;
> > +
> > + u32 reserved: 28;
> > + } bits;
> > + } PHY_TX_TRIGGERS;
> > +
> > + union _0x80 {
> > + u32 val;
> > + struct _DESKEW_START {
> > + u32 deskew_start: 1;
> > + u32 reserved: 31;
> > + } bits;
> > + } DESKEW_START;
> > +
> > + union _0x84 {
> > + u32 val;
> > + struct _DESKEW_MODE {
> > + u32 deskew_mode: 2;
> > + u32 reserved: 30;
> > + } bits;
> > + } DESKEW_MODE;
> > +
> > + union _0x88 {
> > + u32 val;
> > + struct _DESKEW_TIME {
> > + u32 deskew_time: 32;
> > + } bits;
> > + } DESKEW_TIME;
> > +
> > + union _0x8C {
> > + u32 val;
> > + struct _DESKEW_PERIOD {
> > + u32 deskew_period: 32;
> > + } bits;
> > + } DESKEW_PERIOD;
> > +
> > + union _0x90 {
> > + u32 val;
> > + struct _DESKEW_BUSY {
> > + u32 deskew_busy: 1;
> > + u32 reserved: 31;
> > + } bits;
> > + } DESKEW_BUSY;
> > +
> > + union _0x94 {
> > + u32 val;
> > + struct _DESKEW_LANE_MASK {
> > + u32 deskew_lane0_mask: 1;
> > + u32 deskew_lane1_mask: 1;
> > + u32 deskew_lane2_mask: 1;
> > + u32 deskew_lane3_mask: 1;
> > + u32 reserved: 28;
> > + } bits;
> > + } DESKEW_LANE_MASK;
> > +
> > + union _0x98 {
> > + u32 val;
> > + struct _CMD_MODE_STATUS {
> > + /*
> > + * This bit is set when a read command is issued and
> cleared
> > + * when the entire response is stored in the FIFO.
> > + * Value after reset: 0x0
> > + *
> > + * NOTE:
> > + * For mipi-dsi-r1p0 IP, this bit is set immediately when
> > + * the read cmd is set to the GEN_HDR register.
> > + *
> > + * For dsi-ctrl-r1p0 IP, this bit is set only after the
> read
> > + * cmd was actually sent out from the controller.
> > + */
> > + u32 gen_cmd_rdcmd_ongoing: 1;
> > +
> > + /*
> > + * This bit indicates the empty status of the generic read
> > + * payload FIFO.
> > + * Value after reset: 0x1
> > + */
> > + u32 gen_cmd_rdata_fifo_empty: 1;
> > +
> > + /*
> > + * This bit indicates the full status of the generic read
> > + * payload FIFO.
> > + * Value after reset: 0x0
> > + */
> > + u32 gen_cmd_rdata_fifo_full: 1;
> > +
> > + /*
> > + * This bit indicates the empty status of the generic write
> > + * payload FIFO.
> > + * Value after reset: 0x1
> > + */
> > + u32 gen_cmd_wdata_fifo_empty: 1;
> > +
> > + /*
> > + * This bit indicates the full status of the generic write
> > + * payload FIFO.
> > + * Value after reset: 0x0
> > + */
> > + u32 gen_cmd_wdata_fifo_full: 1;
> > +
> > + /*
> > + * This bit indicates the empty status of the generic
> > + * command FIFO.
> > + * Value after reset: 0x1
> > + */
> > + u32 gen_cmd_cmd_fifo_empty: 1;
> > +
> > + /*
> > + * This bit indicates the full status of the generic
> > + * command FIFO.
> > + * Value after reset: 0x0
> > + */
> > + u32 gen_cmd_cmd_fifo_full: 1;
> > +
> > + /*
> > + * This bit is set when the entire response of read is
> > + * stored in the rx payload FIFO. And it will be cleared
> > + * automaticlly after read this bit each time.
> > + * Value after reset: 0x0
> > + *
> > + * NOTE: this bit is just supported for dsi-ctrl-r1p0 IP
> > + */
> > + u32 gen_cmd_rdcmd_done: 1;
> > +
> > + u32 reserved : 24;
> > +
> > + } bits;
> > + } CMD_MODE_STATUS;
> > +
> > + union _0x9C {
> > + u32 val;
> > + struct _PHY_STATUS {
> > + /* the status of phydirection D-PHY signal */
> > + u32 phy_direction: 1;
> > +
> > + /* the status of phylock D-PHY signal */
> > + u32 phy_lock: 1;
> > +
> > + /* the status of rxulpsesc0lane D-PHY signal */
> > + u32 phy_rxulpsesc0lane: 1;
> > +
> > + /* the status of phystopstateclklane D-PHY signal */
> > + u32 phy_stopstateclklane: 1;
> > +
> > + /* the status of phystopstate0lane D-PHY signal */
> > + u32 phy_stopstate0lane: 1;
> > +
> > + /* the status of phystopstate1lane D-PHY signal */
> > + u32 phy_stopstate1lane: 1;
> > +
> > + /* the status of phystopstate2lane D-PHY signal */
> > + u32 phy_stopstate2lane: 1;
> > +
> > + /* the status of phystopstate3lane D-PHY signal */
> > + u32 phy_stopstate3lane: 1;
> > +
> > + /* the status of phyulpsactivenotclk D-PHY signal */
> > + u32 phy_ulpsactivenotclk: 1;
> > +
> > + /* the status of ulpsactivenot0lane D-PHY signal */
> > + u32 phy_ulpsactivenot0lane: 1;
> > +
> > + /* the status of ulpsactivenot1lane D-PHY signal */
> > + u32 phy_ulpsactivenot1lane: 1;
> > +
> > + /* the status of ulpsactivenot2lane D-PHY signal */
> > + u32 phy_ulpsactivenot2lane: 1;
> > +
> > + /* the status of ulpsactivenot3lane D-PHY signal */
> > + u32 phy_ulpsactivenot3lane: 1;
> > +
> > + u32 reserved: 19;
> > +
> > + } bits;
> > + } PHY_STATUS;
> > +
> > + union _0xA0 {
> > + u32 val;
> > + struct _PHY_MIN_STOP_TIME {
> > + /* This field configures the minimum wait period to request
> > + * a high-speed transmission after the Stop state.
> > + */
> > + u32 phy_min_stop_time: 8;
> > +
> > + u32 reserved: 24;
> > + } bits;
> > + } PHY_MIN_STOP_TIME;
> > +
> > + union _0xA4 {
> > + u32 val;
> > + struct _PHY_LANE_NUM_CONFIG {
> > + /*
> > + * This field configures the number of active data lanes:
> > + * 00: One data lane (lane 0)
> > + * 01: Two data lanes (lanes 0 and 1)
> > + * 10: Three data lanes (lanes 0, 1, and 2)
> > + * 11: Four data lanes (lanes 0, 1, 2, and 3)
> > + */
> > + u32 phy_lane_num: 2;
> > +
> > + u32 reserved: 30;
> > +
> > + } bits;
> > + } PHY_LANE_NUM_CONFIG;
> > +
> > + union _0xA8 {
> > + u32 val;
> > + struct _PHY_CLKLANE_TIME_CONFIG {
> > + /*
> > + * This field configures the maximum time that the D-PHY
> > + * clock lane takes to go from low-power to high-speed
> > + * transmission measured in lane byte clock cycles.
> > + */
> > + u32 phy_clklane_lp_to_hs_time: 16;
> > +
> > + /*
> > + * This field configures the maximum time that the D-PHY
> > + * clock lane takes to go from high-speed to low-power
> > + * transmission measured in lane byte clock cycles.
> > + */
> > + u32 phy_clklane_hs_to_lp_time: 16;
> > +
> > + } bits;
> > + } PHY_CLKLANE_TIME_CONFIG;
> > +
> > + union _0xAC {
> > + u32 val;
> > + struct _PHY_DATALANE_TIME_CONFIG {
> > + /*
> > + * This field configures the maximum time that the D-PHY
> data
> > + * lanes take to go from low-power to high-speed
> transmission
> > + * measured in lane byte clock cycles.
> > + */
> > + u32 phy_datalane_lp_to_hs_time: 16;
> > +
> > + /*
> > + * This field configures the maximum time that the D-PHY
> data
> > + * lanes take to go from high-speed to low-power
> transmission
> > + * measured in lane byte clock cycles.
> > + */
> > + u32 phy_datalane_hs_to_lp_time: 16;
> > +
> > + } bits;
> > + } PHY_DATALANE_TIME_CONFIG;
> > +
> > + union _0xB0 {
> > + u32 val;
> > + struct _MAX_READ_TIME {
> > + /*
> > + * This field configures the maximum time required to
> perform
> > + * a read command in lane byte clock cycles. This register
> can
> > + * only be modified when no read command is in progress.
> > + */
> > + u32 max_rd_time: 16;
> > +
> > + u32 reserved: 16;
> > +
> > + } bits;
> > + } MAX_READ_TIME;
> > +
> > + union _0xB4 {
> > + u32 val;
> > + struct _RX_PKT_CHECK_CONFIG {
> > + /* When set to 1, this bit enables the ECC reception, error
> > + * correction, and reporting.
> > + */
> > + u32 rx_pkt_ecc_en: 1;
> > +
> > + /* When set to 1, this bit enables the CRC reception and
> error
> > + * reporting.
> > + */
> > + u32 rx_pkt_crc_en: 1;
> > +
> > + u32 reserved: 30;
> > +
> > + } bits;
> > + } RX_PKT_CHECK_CONFIG;
> > +
> > + union _0xB8 {
> > + u32 val;
> > + struct _TA_EN {
> > + /* When set to 1, this bit enables the Bus Turn-Around
> (BTA)
> > + * request.
> > + */
> > + u32 ta_en: 1;
> > +
> > + u32 reserved: 31;
> > +
> > + } bits;
> > + } TA_EN;
> > +
> > + union _0xBC {
> > + u32 val;
> > + struct _EOTP_EN {
> > + /* When set to 1, this bit enables the EoTp transmission */
> > + u32 tx_eotp_en: 1;
> > +
> > + /* When set to 1, this bit enables the EoTp reception. */
> > + u32 rx_eotp_en: 1;
> > +
> > + u32 reserved: 30;
> > +
> > + } bits;
> > + } EOTP_EN;
> > +
> > + union _0xC0 {
> > + u32 val;
> > + struct _VIDEO_NULLPKT_SIZE {
> > + /*
> > + * This register configures the number of bytes inside a
> null
> > + * packet. Setting it to 0 disables the null packets.
> > + */
> > + u32 video_nullpkt_size: 13;
> > +
> > + u32 reserved: 19;
> > +
> > + } bits;
> > + } VIDEO_NULLPKT_SIZE;
> > +
> > + union _0xC4 {
> > + u32 val;
> > + struct _DCS_WM_PKT_SIZE {
> > + /*
> > + * This field configures the maximum allowed size for an
> eDPI
> > + * write memory command, measured in pixels. Automatic
> parti-
> > + * tioning of data obtained from eDPI is permanently
> enabled.
> > + */
> > + u32 dcs_wm_pkt_size: 16;
> > +
> > + u32 reserved: 16;
> > + } bits;
> > + } DCS_WM_PKT_SIZE;
> > +
> > + union _0xC8 {
> > + u32 val;
> > + struct _PROTOCOL_INT_CLR {
> > + u32 clr_dphy_errors_0: 1;
> > + u32 clr_dphy_errors_1: 1;
> > + u32 clr_dphy_errors_2: 1;
> > + u32 clr_dphy_errors_3: 1;
> > + u32 clr_dphy_errors_4: 1;
> > + u32 clr_protocol_debug_err: 11;
> > + u32 clr_ack_with_err_0: 1;
> > + u32 clr_ack_with_err_1: 1;
> > + u32 clr_ack_with_err_2: 1;
> > + u32 clr_ack_with_err_3: 1;
> > + u32 clr_ack_with_err_4: 1;
> > + u32 clr_ack_with_err_5: 1;
> > + u32 clr_ack_with_err_6: 1;
> > + u32 clr_ack_with_err_7: 1;
> > + u32 clr_ack_with_err_8: 1;
> > + u32 clr_ack_with_err_9: 1;
> > + u32 clr_ack_with_err_10: 1;
> > + u32 clr_ack_with_err_11: 1;
> > + u32 clr_ack_with_err_12: 1;
> > + u32 clr_ack_with_err_13: 1;
> > + u32 clr_ack_with_err_14: 1;
> > + u32 clr_ack_with_err_15: 1;
> > + } bits;
> > + } PROTOCOL_INT_CLR;
> > +
> > + union _0xCC {
> > + u32 val;
> > + struct _INTERNAL_INT_CLR {
> > + u32 clr_receive_pkt_size_err: 1;
> > + u32 clr_eopt_not_receive_err: 1;
> > + u32 clr_gen_cmd_cmd_fifo_wr_err: 1;
> > + u32 clr_gen_cmd_rdata_fifo_rd_err: 1;
> > + u32 clr_gen_cmd_rdata_fifo_wr_err: 1;
> > + u32 clr_gen_cmd_wdata_fifo_wr_err: 1;
> > + u32 clr_gen_cmd_wdata_fifo_rd_err: 1;
> > + u32 clr_dpi_pix_fifo_wr_err: 1;
> > + u32 clr_internal_debug_err: 19;
> > + u32 clr_ecc_single_err: 1;
> > + u32 clr_ecc_multi_err: 1;
> > + u32 clr_crc_err: 1;
> > + u32 clr_hs_tx_timeout: 1;
> > + u32 clr_lp_rx_timeout: 1;
> > + } bits;
> > + } INTERNAL_INT_CLR;
> > +
> > + union _0xD0 {
> > + u32 val;
> > + struct _VIDEO_SIG_DELAY_CONFIG {
> > +
> > + /*
> > + * DPI interface signal delay to be used in clk lanebyte
> > + * domain for control logic to read video data from pixel
> > + * memory in mannal mode, measured in clk_lanebyte cycles
> > + */
> > + u32 video_sig_delay: 24;
> > +
> > + /*
> > + * 1'b1: mannal mode
> > + * dsi controller will use video_sig_delay value as
> > + * the delay for the packet handle logic to read
> video
> > + * data from pixel memory.
> > + *
> > + * 1'b0: auto mode
> > + * dsi controller will auto calculate the delay for
> > + * the packet handle logic to read video data from
> > + * pixel memory.
> > + */
> > + u32 video_sig_delay_mode: 1;
> > +
> > + u32 reserved: 7;
> > + } bits;
> > + } VIDEO_SIG_DELAY_CONFIG;
> > +
> > + u32 reservedD4_EC[7];
> > +
> > + union _0xF0 {
> > + u32 val;
> > + struct _PHY_TST_CTRL0 {
> > + /* PHY test interface clear (active high) */
> > + u32 phy_testclr: 1;
> > +
> > + /* This bit is used to clock the TESTDIN bus into the
> D-PHY */
> > + u32 phy_testclk: 1;
> > +
> > + u32 reserved: 30;
> > + } bits;
> > + } PHY_TST_CTRL0;
> > +
> > + union _0xF4 {
> > + u32 val;
> > + struct _PHY_TST_CTRL1 {
> > + /* PHY test interface input 8-bit data bus for internal
> > + * register programming and test functionalities access.
> > + */
> > + u32 phy_testdin: 8;
> > +
> > + /* PHY output 8-bit data bus for read-back and internal
> > + * probing functionalities.
> > + */
> > + u32 phy_testdout: 8;
> > +
> > + /*
> > + * PHY test interface operation selector:
> > + * 1: The address write operation is set on the falling
> edge
> > + * of the testclk signal.
> > + * 0: The data write operation is set on the rising edge of
> > + * the testclk signal.
> > + */
> > + u32 phy_testen: 1;
> > +
> > + u32 reserved: 15;
> > + } bits;
> > + } PHY_TST_CTRL1;
> > +
> > + u32 reservedF8_1FC[66];
> > +
> > + union _0x200 {
> > + u32 val;
> > + struct _INT_PLL_STS {
> > + u32 int_pll_sts: 1;
> > + u32 reserved: 31;
> > + } bits;
> > + } INT_PLL_STS;
> > +
> > + union _0x204 {
> > + u32 val;
> > + struct _INT_PLL_MSK {
> > + u32 int_pll_msk: 1;
> > + u32 reserved: 31;
> > + } bits;
> > + } INT_PLL_MSK;
> > +
> > + union _0x208 {
> > + u32 val;
> > + struct _INT_PLL_CLR {
> > + u32 int_pll_clr: 1;
> > + u32 reserved: 31;
> > + } bits;
> > + } INT_PLL_CLR;
> > +
> > +};
> > +
> > +void dsi_power_enable(struct dsi_context *ctx, int enable);
> > +void dsi_video_mode(struct dsi_context *ctx);
> > +void dsi_cmd_mode(struct dsi_context *ctx);
> > +bool dsi_is_cmd_mode(struct dsi_context *ctx);
> > +void dsi_rx_vcid(struct dsi_context *ctx, u8 vc);
> > +void dsi_video_vcid(struct dsi_context *ctx, u8 vc);
> > +void dsi_dpi_video_burst_mode(struct dsi_context *ctx, int mode);
> > +void dsi_dpi_color_coding(struct dsi_context *ctx, int coding);
> > +void dsi_dpi_sig_delay(struct dsi_context *ctx, u16 byte_cycle);
> > +void dsi_dpi_hline_time(struct dsi_context *ctx, u16 byte_cycle);
> > +void dsi_dpi_hsync_time(struct dsi_context *ctx, u16 byte_cycle);
> > +void dsi_dpi_hbp_time(struct dsi_context *ctx, u16 byte_cycle);
> > +void dsi_dpi_vact(struct dsi_context *ctx, u16 lines);
> > +void dsi_dpi_vfp(struct dsi_context *ctx, u16 lines);
> > +void dsi_dpi_vbp(struct dsi_context *ctx, u16 lines);
> > +void dsi_dpi_vsync(struct dsi_context *ctx, u16 lines);
> > +void dsi_dpi_hporch_lp_en(struct dsi_context *ctx, int enable);
> > +void dsi_dpi_vporch_lp_en(struct dsi_context *ctx, int enable);
> > +void dsi_dpi_frame_ack_en(struct dsi_context *ctx, int enable);
> > +void dsi_dpi_chunk_num(struct dsi_context *ctx, u16 no);
> > +void dsi_dpi_null_packet_size(struct dsi_context *ctx, u16 size);
> > +void dsi_dpi_video_packet_size(struct dsi_context *ctx, u16 size);
> > +void dsi_edpi_max_pkt_size(struct dsi_context *ctx, u16 size);
> > +void dsi_tear_effect_ack_en(struct dsi_context *ctx, int enable);
> > +void dsi_cmd_mode_lp_cmd_en(struct dsi_context *ctx, int enable);
> > +void dsi_video_mode_lp_cmd_en(struct dsi_context *ctx, int enable);
> > +void dsi_set_packet_header(struct dsi_context *ctx, u8 vc, u8 type,
> > + u8 wc_lsb, u8 wc_msb);
> > +void dsi_set_packet_payload(struct dsi_context *ctx, u32 payload);
> > +u32 dsi_get_rx_payload(struct dsi_context *ctx);
> > +void dsi_bta_en(struct dsi_context *ctx, int enable);
> > +void dsi_eotp_rx_en(struct dsi_context *ctx, int enable);
> > +void dsi_eotp_tx_en(struct dsi_context *ctx, int enable);
> > +void dsi_ecc_rx_en(struct dsi_context *ctx, int enable);
> > +void dsi_crc_rx_en(struct dsi_context *ctx, int enable);
> > +bool dsi_is_bta_returned(struct dsi_context *ctx);
> > +bool dsi_is_rx_payload_fifo_full(struct dsi_context *ctx);
> > +bool dsi_is_rx_payload_fifo_empty(struct dsi_context *ctx);
> > +bool dsi_is_tx_payload_fifo_full(struct dsi_context *ctx);
> > +bool dsi_is_tx_payload_fifo_empty(struct dsi_context *ctx);
> > +bool dsi_is_tx_cmd_fifo_empty(struct dsi_context *ctx);
> > +void dsi_datalane_hs2lp_config(struct dsi_context *ctx, u16 byte_cycle);
> > +void dsi_datalane_lp2hs_config(struct dsi_context *ctx, u16 byte_cycle);
> > +void dsi_clklane_hs2lp_config(struct dsi_context *ctx, u16 byte_cycle);
> > +void dsi_clklane_lp2hs_config(struct dsi_context *ctx, u16 byte_cycle);
> > +void dsi_max_read_time(struct dsi_context *ctx, u16 byte_cycle);
> > +void dsi_nc_clk_en(struct dsi_context *ctx, int enable);
> > +void dsi_tx_escape_division(struct dsi_context *ctx, u8 div);
> > +void dsi_timeout_clock_division(struct dsi_context *ctx, u8 div);
> > +void dsi_lp_rx_timeout(struct dsi_context *ctx, u16 count);
> > +void dsi_hs_tx_timeout(struct dsi_context *ctx, u16 count);
> > +u32 dsi_int0_status(struct dsi_context *ctx);
> > +u32 dsi_int1_status(struct dsi_context *ctx);
> > +void dsi_int0_mask(struct dsi_context *ctx, u32 mask);
> > +void dsi_int1_mask(struct dsi_context *ctx, u32 mask);
> > +
> > +#endif /* _DW_DSI_CTRL_H_ */
> > diff --git a/drivers/gpu/drm/sprd/dw_dsi_ctrl_ppi.c
> b/drivers/gpu/drm/sprd/dw_dsi_ctrl_ppi.c
> > new file mode 100644
> > index 0000000..6e28d7c
> > --- /dev/null
> > +++ b/drivers/gpu/drm/sprd/dw_dsi_ctrl_ppi.c
> > @@ -0,0 +1,157 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Copyright (C) 2020 Unisoc Inc.
> > + */
> > +
> > +#include <linux/io.h>
> > +#include <linux/init.h>
> > +#include <linux/module.h>
> > +
> > +#include "dw_dsi_ctrl.h"
> > +#include "dw_dsi_ctrl_ppi.h"
> > +
> > +/*
> > + * Reset D-PHY module
> > + */
> > +void dsi_phy_rstz(struct dsi_context *ctx, int level)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x78 phy_interface_ctrl;
> > +
> > + phy_interface_ctrl.val = readl(®->PHY_INTERFACE_CTRL);
> > + phy_interface_ctrl.bits.rf_phy_reset_n = level;
> > +
> > + writel(phy_interface_ctrl.val, ®->PHY_INTERFACE_CTRL);
> > +}
> > +
> > +/*
> > + * Power up/down D-PHY module
> > + */
> > +void dsi_phy_shutdownz(struct dsi_context *ctx, int level)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x78 phy_interface_ctrl;
> > +
> > + phy_interface_ctrl.val = readl(®->PHY_INTERFACE_CTRL);
> > + phy_interface_ctrl.bits.rf_phy_shutdown = level;
> > +
> > + writel(phy_interface_ctrl.val, ®->PHY_INTERFACE_CTRL);
> > +}
> > +
> > +/*
> > + * Configure minimum wait period for HS transmission request after a
> stop state
> > + */
> > +void dsi_phy_stop_wait_time(struct dsi_context *ctx, u8 byte_cycle)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > +
> > + writel(byte_cycle, ®->PHY_MIN_STOP_TIME);
> > +}
> > +
> > +/*
> > + * Set number of active lanes
> > + */
> > +void dsi_phy_datalane_en(struct dsi_context *ctx)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > +
> > + writel(ctx->lanes - 1, ®->PHY_LANE_NUM_CONFIG);
> > +}
> > +
> > +/*
> > + * Enable clock lane module
> > + */
> > +void dsi_phy_clklane_en(struct dsi_context *ctx, int en)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x78 phy_interface_ctrl;
> > +
> > + phy_interface_ctrl.val = readl(®->PHY_INTERFACE_CTRL);
> > + phy_interface_ctrl.bits.rf_phy_clk_en = en;
> > +
> > + writel(phy_interface_ctrl.val, ®->PHY_INTERFACE_CTRL);
> > +}
> > +
> > +/*
> > + * Request the PHY module to start transmission of high speed clock.
> > + * This causes the clock lane to start transmitting DDR clock on the
> > + * lane interconnect.
> > + */
> > +void dsi_phy_clk_hs_rqst(struct dsi_context *ctx, int enable)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x74 phy_clk_lane_lp_ctrl;
> > +
> > + phy_clk_lane_lp_ctrl.val = readl(®->PHY_CLK_LANE_LP_CTRL);
> > + phy_clk_lane_lp_ctrl.bits.auto_clklane_ctrl_en = 0;
> > + phy_clk_lane_lp_ctrl.bits.phy_clklane_tx_req_hs = enable;
> > +
> > + writel(phy_clk_lane_lp_ctrl.val, ®->PHY_CLK_LANE_LP_CTRL);
> > +}
> > +
> > +/*
> > + * Get D-PHY PPI status
> > + */
> > +u8 dsi_phy_is_pll_locked(struct dsi_context *ctx)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0x9C phy_status;
> > +
> > + phy_status.val = readl(®->PHY_STATUS);
> > +
> > + return phy_status.bits.phy_lock;
> > +}
> > +
> > +void dsi_phy_test_clk(struct dsi_context *ctx, u8 value)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0xF0 phy_tst_ctrl0;
> > +
> > + phy_tst_ctrl0.val = readl(®->PHY_TST_CTRL0);
> > + phy_tst_ctrl0.bits.phy_testclk = value;
> > +
> > + writel(phy_tst_ctrl0.val, ®->PHY_TST_CTRL0);
> > +}
> > +
> > +void dsi_phy_test_clr(struct dsi_context *ctx, u8 value)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0xF0 phy_tst_ctrl0;
> > +
> > + phy_tst_ctrl0.val = readl(®->PHY_TST_CTRL0);
> > + phy_tst_ctrl0.bits.phy_testclr = value;
> > +
> > + writel(phy_tst_ctrl0.val, ®->PHY_TST_CTRL0);
> > +}
> > +
> > +void dsi_phy_test_en(struct dsi_context *ctx, u8 value)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0xF4 phy_tst_ctrl1;
> > +
> > + phy_tst_ctrl1.val = readl(®->PHY_TST_CTRL1);
> > + phy_tst_ctrl1.bits.phy_testen = value;
> > +
> > + writel(phy_tst_ctrl1.val, ®->PHY_TST_CTRL1);
> > +}
> > +
> > +u8 dsi_phy_test_dout(struct dsi_context *ctx)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0xF4 phy_tst_ctrl1;
> > +
> > + phy_tst_ctrl1.val = readl(®->PHY_TST_CTRL1);
> > +
> > + return phy_tst_ctrl1.bits.phy_testdout;
> > +}
> > +
> > +void dsi_phy_test_din(struct dsi_context *ctx, u8 data)
> > +{
> > + struct dsi_reg *reg = (struct dsi_reg *)ctx->base;
> > + union _0xF4 phy_tst_ctrl1;
> > +
> > + phy_tst_ctrl1.val = readl(®->PHY_TST_CTRL1);
> > + phy_tst_ctrl1.bits.phy_testdin = data;
> > +
> > + writel(phy_tst_ctrl1.val, ®->PHY_TST_CTRL1);
> > +}
> > diff --git a/drivers/gpu/drm/sprd/dw_dsi_ctrl_ppi.h
> b/drivers/gpu/drm/sprd/dw_dsi_ctrl_ppi.h
> > new file mode 100644
> > index 0000000..d87fb75
> > --- /dev/null
> > +++ b/drivers/gpu/drm/sprd/dw_dsi_ctrl_ppi.h
> > @@ -0,0 +1,26 @@
> > +/* SPDX-License-Identifier: GPL-2.0 */
> > +/*
> > + * Copyright (C) 2020 Unisoc Inc.
> > + */
> > +
> > +#ifndef _DW_DSI_CTRL_PPI_H_
> > +#define _DW_DSI_CTRL_PPI_H_
> > +
> > +#include "sprd_dsi.h"
> > +
> > +void dsi_phy_rstz(struct dsi_context *ctx, int level);
> > +void dsi_phy_shutdownz(struct dsi_context *ctx, int level);
> > +void dsi_phy_force_pll(struct dsi_context *ctx, int force);
> > +void dsi_phy_stop_wait_time(struct dsi_context *ctx, u8 byte_clk);
> > +void dsi_phy_datalane_en(struct dsi_context *ctx);
> > +void dsi_phy_clklane_en(struct dsi_context *ctx, int en);
> > +void dsi_phy_clk_hs_rqst(struct dsi_context *ctx, int en);
> > +u8 dsi_phy_is_pll_locked(struct dsi_context *ctx);
> > +void dsi_phy_test_clk(struct dsi_context *ctx, u8 level);
> > +void dsi_phy_test_clr(struct dsi_context *ctx, u8 level);
> > +void dsi_phy_test_en(struct dsi_context *ctx, u8 level);
> > +u8 dsi_phy_test_dout(struct dsi_context *ctx);
> > +void dsi_phy_test_din(struct dsi_context *ctx, u8 data);
> > +void dsi_phy_bist_en(struct dsi_context *ctx, int en);
> > +
> > +#endif /* _DW_DSI_CTRL_PPI_H_ */
> > \ No newline at end of file
> > diff --git a/drivers/gpu/drm/sprd/megacores_pll.c
> b/drivers/gpu/drm/sprd/megacores_pll.c
> > new file mode 100644
> > index 0000000..03c1f0f
> > --- /dev/null
> > +++ b/drivers/gpu/drm/sprd/megacores_pll.c
> > @@ -0,0 +1,317 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Copyright (C) 2020 Unisoc Inc.
> > + */
> > +
> > +#include <asm/div64.h>
> > +#include <linux/delay.h>
> > +#include <linux/init.h>
> > +#include <linux/kernel.h>
> > +#include <linux/regmap.h>
> > +#include <linux/string.h>
> > +
> > +#include "megacores_pll.h"
> > +
> > +#define L 0
> > +#define H 1
> > +#define CLK 0
> > +#define DATA 1
> > +#define INFINITY 0xffffffff
> > +#define MIN_OUTPUT_FREQ (100)
> > +
> > +#define AVERAGE(a, b) (min(a, b) + abs((b) - (a)) / 2)
> > +
> > +/* sharkle */
> > +#define VCO_BAND_LOW 750
> > +#define VCO_BAND_MID 1100
> > +#define VCO_BAND_HIGH 1500
> > +#define PHY_REF_CLK 26000
> > +
> > +static int dphy_calc_pll_param(struct dphy_pll *pll)
> > +{
> > + const u32 khz = 1000;
> > + const u32 mhz = 1000000;
> > + const unsigned long long factor = 100;
> > + unsigned long long tmp;
> > + int i;
> > +
> > + pll->potential_fvco = pll->freq / khz;
> > + pll->ref_clk = PHY_REF_CLK / khz;
> > +
> > + for (i = 0; i < 4; ++i) {
> > + if (pll->potential_fvco >= VCO_BAND_LOW &&
> > + pll->potential_fvco <= VCO_BAND_HIGH) {
> > + pll->fvco = pll->potential_fvco;
> > + pll->out_sel = BIT(i);
> > + break;
> > + }
> > + pll->potential_fvco <<= 1;
> > + }
> > + if (pll->fvco == 0)
> > + return -EINVAL;
> > +
> > + if (pll->fvco >= VCO_BAND_LOW && pll->fvco <= VCO_BAND_MID) {
> > + /* vco band control */
> > + pll->vco_band = 0x0;
> > + /* low pass filter control */
> > + pll->lpf_sel = 1;
> > + } else if (pll->fvco > VCO_BAND_MID && pll->fvco <= VCO_BAND_HIGH)
> {
> > + pll->vco_band = 0x1;
> > + pll->lpf_sel = 0;
> > + } else
> > + return -EINVAL;
> > +
> > + pll->nint = pll->fvco / pll->ref_clk;
> > + tmp = pll->fvco * factor * mhz;
> > + do_div(tmp, pll->ref_clk);
> > + tmp = tmp - pll->nint * factor * mhz;
> > + tmp *= BIT(20);
> > + do_div(tmp, 100000000);
> > + pll->kint = (u32)tmp;
> > + pll->refin = 3; /* pre-divider bypass */
> > + pll->sdm_en = true; /* use fraction N PLL */
> > + pll->fdk_s = 0x1; /* fraction */
> > + pll->cp_s = 0x0;
> > + pll->det_delay = 0x1;
> > +
> > + return 0;
> > +}
> > +
> > +static void dphy_set_pll_reg(struct dphy_pll *pll, struct regmap
> *regmap)
> > +{
> > + struct pll_reg *reg = &pll->reg;
> > + u8 *val;
> > + int i;
> > +
> > + u8 reg_addr[] = {
> > + 0x03, 0x04, 0x06, 0x08, 0x09,
> > + 0x0a, 0x0b, 0x0e, 0x0f
> > + };
> > +
> > + reg->_03.bits.prbs_bist = 1;
> > + reg->_03.bits.en_lp_treot = true;
> > + reg->_03.bits.lpf_sel = pll->lpf_sel;
> > + reg->_03.bits.txfifo_bypass = 0;
> > + reg->_04.bits.div = pll->div;
> > + reg->_04.bits.masterof8lane = 1;
> > + reg->_04.bits.cp_s = pll->cp_s;
> > + reg->_04.bits.fdk_s = pll->fdk_s;
> > + reg->_06.bits.nint = pll->nint;
> > + reg->_08.bits.vco_band = pll->vco_band;
> > + reg->_08.bits.sdm_en = pll->sdm_en;
> > + reg->_08.bits.refin = pll->refin;
> > + reg->_09.bits.kint_h = pll->kint >> 12;
> > + reg->_0a.bits.kint_m = (pll->kint >> 4) & 0xff;
> > + reg->_0b.bits.out_sel = pll->out_sel;
> > + reg->_0b.bits.kint_l = pll->kint & 0xf;
> > + reg->_0e.bits.pll_pu_byp = 0;
> > + reg->_0e.bits.pll_pu = 0;
> > + reg->_0e.bits.stopstate_sel = 1;
> > + reg->_0f.bits.det_delay = pll->det_delay;
> > +
> > + val = (u8 *)®
> > +
> > + for (i = 0; i < sizeof(reg_addr); ++i) {
> > + regmap_write(regmap, reg_addr[i], val[i]);
> > + DRM_DEBUG("%02x: %02x\n", reg_addr[i], val[i]);
> > + }
> > +}
> > +
> > +int dphy_pll_config(struct dsi_context *ctx)
> > +{
> > + struct sprd_dsi *dsi = container_of(ctx, struct sprd_dsi, ctx);
> > + struct regmap *regmap = ctx->regmap;
> > + struct dphy_pll *pll = ctx->pll;
> > + int ret;
> > +
> > + pll->freq = ctx->byte_clk * 8;
> > +
> > + /* FREQ = 26M * (NINT + KINT / 2^20) / out_sel */
> > + ret = dphy_calc_pll_param(pll);
> > + if (ret) {
> > + drm_err(dsi->drm, "failed to calculate dphy pll
> parameters\n");
> > + return ret;
> > + }
> > + dphy_set_pll_reg(pll, regmap);
> > +
> > + return 0;
> > +}
> > +
> > +static void dphy_set_timing_reg(struct regmap *regmap, int type, u8
> val[])
> > +{
> > + switch (type) {
> > + case REQUEST_TIME:
> > + regmap_write(regmap, 0x31, val[CLK]);
> > + regmap_write(regmap, 0x41, val[DATA]);
> > + regmap_write(regmap, 0x51, val[DATA]);
> > + regmap_write(regmap, 0x61, val[DATA]);
> > + regmap_write(regmap, 0x71, val[DATA]);
> > +
> > + regmap_write(regmap, 0x90, val[CLK]);
> > + regmap_write(regmap, 0xa0, val[DATA]);
> > + regmap_write(regmap, 0xb0, val[DATA]);
> > + regmap_write(regmap, 0xc0, val[DATA]);
> > + regmap_write(regmap, 0xd0, val[DATA]);
> > + break;
> > + case PREPARE_TIME:
> > + regmap_write(regmap, 0x32, val[CLK]);
> > + regmap_write(regmap, 0x42, val[DATA]);
> > + regmap_write(regmap, 0x52, val[DATA]);
> > + regmap_write(regmap, 0x62, val[DATA]);
> > + regmap_write(regmap, 0x72, val[DATA]);
> > +
> > + regmap_write(regmap, 0x91, val[CLK]);
> > + regmap_write(regmap, 0xa1, val[DATA]);
> > + regmap_write(regmap, 0xb1, val[DATA]);
> > + regmap_write(regmap, 0xc1, val[DATA]);
> > + regmap_write(regmap, 0xd1, val[DATA]);
> > + break;
> > + case ZERO_TIME:
> > + regmap_write(regmap, 0x33, val[CLK]);
> > + regmap_write(regmap, 0x43, val[DATA]);
> > + regmap_write(regmap, 0x53, val[DATA]);
> > + regmap_write(regmap, 0x63, val[DATA]);
> > + regmap_write(regmap, 0x73, val[DATA]);
> > +
> > + regmap_write(regmap, 0x92, val[CLK]);
> > + regmap_write(regmap, 0xa2, val[DATA]);
> > + regmap_write(regmap, 0xb2, val[DATA]);
> > + regmap_write(regmap, 0xc2, val[DATA]);
> > + regmap_write(regmap, 0xd2, val[DATA]);
> > + break;
> > + case TRAIL_TIME:
> > + regmap_write(regmap, 0x34, val[CLK]);
> > + regmap_write(regmap, 0x44, val[DATA]);
> > + regmap_write(regmap, 0x54, val[DATA]);
> > + regmap_write(regmap, 0x64, val[DATA]);
> > + regmap_write(regmap, 0x74, val[DATA]);
> > +
> > + regmap_write(regmap, 0x93, val[CLK]);
> > + regmap_write(regmap, 0xa3, val[DATA]);
> > + regmap_write(regmap, 0xb3, val[DATA]);
> > + regmap_write(regmap, 0xc3, val[DATA]);
> > + regmap_write(regmap, 0xd3, val[DATA]);
> > + break;
> > + case EXIT_TIME:
> > + regmap_write(regmap, 0x36, val[CLK]);
> > + regmap_write(regmap, 0x46, val[DATA]);
> > + regmap_write(regmap, 0x56, val[DATA]);
> > + regmap_write(regmap, 0x66, val[DATA]);
> > + regmap_write(regmap, 0x76, val[DATA]);
> > +
> > + regmap_write(regmap, 0x95, val[CLK]);
> > + regmap_write(regmap, 0xA5, val[DATA]);
> > + regmap_write(regmap, 0xB5, val[DATA]);
> > + regmap_write(regmap, 0xc5, val[DATA]);
> > + regmap_write(regmap, 0xd5, val[DATA]);
> > + break;
> > + case CLKPOST_TIME:
> > + regmap_write(regmap, 0x35, val[CLK]);
> > + regmap_write(regmap, 0x94, val[CLK]);
> > + break;
> > +
> > + /* the following just use default value */
> > + case SETTLE_TIME:
> > + case TA_GET:
> > + case TA_GO:
> > + case TA_SURE:
> > + break;
> > + default:
> > + break;
> > + }
> > +}
> > +
> > +void dphy_timing_config(struct dsi_context *ctx)
> > +{
> > + struct regmap *regmap = ctx->regmap;
> > + struct dphy_pll *pll = ctx->pll;
> > + const u32 factor = 2;
> > + const u32 scale = 100;
> > + u32 t_ui, t_byteck, t_half_byteck;
> > + u32 range[2], constant;
> > + u8 val[2];
> > + u32 tmp = 0;
> > +
> > + /* t_ui: 1 ui, byteck: 8 ui, half byteck: 4 ui */
> > + t_ui = 1000 * scale / (pll->freq / 1000);
> > + t_byteck = t_ui << 3;
> > + t_half_byteck = t_ui << 2;
> > + constant = t_ui << 1;
> > +
> > + /* REQUEST_TIME: HS T-LPX: LP-01
> > + * For T-LPX, mipi spec defined min value is 50ns,
> > + * but maybe it shouldn't be too small, because BTA,
> > + * LP-10, LP-00, LP-01, all of this is related to T-LPX.
> > + */
> > + range[L] = 50 * scale;
> > + range[H] = INFINITY;
> > + val[CLK] = DIV_ROUND_UP(range[L] * (factor << 1), t_byteck) - 2;
> > + val[DATA] = val[CLK];
> > + dphy_set_timing_reg(regmap, REQUEST_TIME, val);
> > +
> > + /* PREPARE_TIME: HS sequence: LP-00 */
> > + range[L] = 38 * scale;
> > + range[H] = 95 * scale;
> > + tmp = AVERAGE(range[L], range[H]);
> > + val[CLK] = DIV_ROUND_UP(AVERAGE(range[L], range[H]),
> > + t_half_byteck) - 1;
> > + range[L] = 40 * scale + 4 * t_ui;
> > + range[H] = 85 * scale + 6 * t_ui;
> > + tmp |= AVERAGE(range[L], range[H]) << 16;
> > + val[DATA] = DIV_ROUND_UP(AVERAGE(range[L], range[H]),
> > + t_half_byteck) - 1;
> > + dphy_set_timing_reg(regmap, PREPARE_TIME, val);
> > +
> > + /* ZERO_TIME: HS-ZERO */
> > + range[L] = 300 * scale;
> > + range[H] = INFINITY;
> > + val[CLK] = DIV_ROUND_UP(range[L] * factor + (tmp & 0xffff)
> > + - 525 * t_byteck / 100, t_byteck) - 2;
> > + range[L] = 145 * scale + 10 * t_ui;
> > + val[DATA] = DIV_ROUND_UP(range[L] * factor
> > + + ((tmp >> 16) & 0xffff) - 525 * t_byteck / 100,
> > + t_byteck) - 2;
> > + dphy_set_timing_reg(regmap, ZERO_TIME, val);
> > +
> > + /* TRAIL_TIME: HS-TRAIL */
> > + range[L] = 60 * scale;
> > + range[H] = INFINITY;
> > + val[CLK] = DIV_ROUND_UP(range[L] * factor - constant,
> t_half_byteck);
> > + range[L] = max(8 * t_ui, 60 * scale + 4 * t_ui);
> > + val[DATA] = DIV_ROUND_UP(range[L] * 3 / 2 - constant,
> t_half_byteck) - 2;
> > + dphy_set_timing_reg(regmap, TRAIL_TIME, val);
> > +
> > + /* EXIT_TIME: */
> > + range[L] = 100 * scale;
> > + range[H] = INFINITY;
> > + val[CLK] = DIV_ROUND_UP(range[L] * factor, t_byteck) - 2;
> > + val[DATA] = val[CLK];
> > + dphy_set_timing_reg(regmap, EXIT_TIME, val);
> > +
> > + /* CLKPOST_TIME: */
> > + range[L] = 60 * scale + 52 * t_ui;
> > + range[H] = INFINITY;
> > + val[CLK] = DIV_ROUND_UP(range[L] * factor, t_byteck) - 2;
> > + val[DATA] = val[CLK];
> > + dphy_set_timing_reg(regmap, CLKPOST_TIME, val);
> > +
> > + /* SETTLE_TIME:
> > + * This time is used for receiver. So for transmitter,
> > + * it can be ignored.
> > + */
> > +
> > + /* TA_GO:
> > + * transmitter drives bridge state(LP-00) before releasing control,
> > + * reg 0x1f default value: 0x04, which is good.
> > + */
> > +
> > + /* TA_SURE:
> > + * After LP-10 state and before bridge state(LP-00),
> > + * reg 0x20 default value: 0x01, which is good.
> > + */
> > +
> > + /* TA_GET:
> > + * receiver drives Bridge state(LP-00) before releasing control
> > + * reg 0x21 default value: 0x03, which is good.
> > + */
> > +}
> > diff --git a/drivers/gpu/drm/sprd/megacores_pll.h
> b/drivers/gpu/drm/sprd/megacores_pll.h
> > new file mode 100644
> > index 0000000..750dbbc
> > --- /dev/null
> > +++ b/drivers/gpu/drm/sprd/megacores_pll.h
> > @@ -0,0 +1,146 @@
> > +/* SPDX-License-Identifier: GPL-2.0 */
> > +/*
> > + * Copyright (C) 2020 Unisoc Inc.
> > + */
> > +
> > +#ifndef _MEGACORES_PLL_H_
> > +#define _MEGACORES_PLL_H_
> > +
> > +#include "sprd_dsi.h"
> > +
> > +enum PLL_TIMING {
> > + NONE,
> > + REQUEST_TIME,
> > + PREPARE_TIME,
> > + SETTLE_TIME,
> > + ZERO_TIME,
> > + TRAIL_TIME,
> > + EXIT_TIME,
> > + CLKPOST_TIME,
> > + TA_GET,
> > + TA_GO,
> > + TA_SURE,
> > + TA_WAIT,
> > +};
> > +
> > +struct pll_reg {
> > + union __reg_03__ {
> > + struct __03 {
> > + u8 prbs_bist: 1;
> > + u8 en_lp_treot: 1;
> > + u8 lpf_sel: 4;
> > + u8 txfifo_bypass: 1;
> > + u8 freq_hopping: 1;
> > + } bits;
> > + u8 val;
> > + } _03;
> > + union __reg_04__ {
> > + struct __04 {
> > + u8 div: 3;
> > + u8 masterof8lane: 1;
> > + u8 hop_trig: 1;
> > + u8 cp_s: 2;
> > + u8 fdk_s: 1;
> > + } bits;
> > + u8 val;
> > + } _04;
> > + union __reg_06__ {
> > + struct __06 {
> > + u8 nint: 7;
> > + u8 mod_en: 1;
> > + } bits;
> > + u8 val;
> > + } _06;
> > + union __reg_07__ {
> > + struct __07 {
> > + u8 kdelta_h: 8;
> > + } bits;
> > + u8 val;
> > + } _07;
> > + union __reg_08__ {
> > + struct __08 {
> > + u8 vco_band: 1;
> > + u8 sdm_en: 1;
> > + u8 refin: 2;
> > + u8 kdelta_l: 4;
> > + } bits;
> > + u8 val;
> > + } _08;
> > + union __reg_09__ {
> > + struct __09 {
> > + u8 kint_h: 8;
> > + } bits;
> > + u8 val;
> > + } _09;
> > + union __reg_0a__ {
> > + struct __0a {
> > + u8 kint_m: 8;
> > + } bits;
> > + u8 val;
> > + } _0a;
> > + union __reg_0b__ {
> > + struct __0b {
> > + u8 out_sel: 4;
> > + u8 kint_l: 4;
> > + } bits;
> > + u8 val;
> > + } _0b;
> > + union __reg_0c__ {
> > + struct __0c {
> > + u8 kstep_h: 8;
> > + } bits;
> > + u8 val;
> > + } _0c;
> > + union __reg_0d__ {
> > + struct __0d {
> > + u8 kstep_m: 8;
> > + } bits;
> > + u8 val;
> > + } _0d;
> > + union __reg_0e__ {
> > + struct __0e {
> > + u8 pll_pu_byp: 1;
> > + u8 pll_pu: 1;
> > + u8 hsbist_len: 2;
> > + u8 stopstate_sel: 1;
> > + u8 kstep_l: 3;
> > + } bits;
> > + u8 val;
> > + } _0e;
> > + union __reg_0f__ {
> > + struct __0f {
> > + u8 det_delay:2;
> > + u8 kdelta: 4;
> > + u8 ldo0p4:2;
> > + } bits;
> > + u8 val;
> > + } _0f;
> > +};
> > +
> > +struct dphy_pll {
> > + u8 refin; /* Pre-divider control signal */
> > + u8 cp_s; /* 00: SDM_EN=1, 10: SDM_EN=0 */
> > + u8 fdk_s; /* PLL mode control: integer or fraction */
> > + u8 sdm_en;
> > + u8 div;
> > + u8 int_n; /* integer N PLL */
> > + u32 ref_clk; /* dphy reference clock, unit: MHz */
> > + u32 freq; /* panel config, unit: KHz */
> > + u32 fvco;
> > + u32 potential_fvco;
> > + u32 nint; /* sigma delta modulator NINT control */
> > + u32 kint; /* sigma delta modulator KINT control */
> > + u8 lpf_sel; /* low pass filter control */
> > + u8 out_sel; /* post divider control */
> > + u8 vco_band; /* vco range */
> > + u8 det_delay;
> > +
> > + struct pll_reg reg;
> > +};
> > +
> > +struct dsi_context;
> > +
> > +int dphy_pll_config(struct dsi_context *ctx);
> > +void dphy_timing_config(struct dsi_context *ctx);
> > +
> > +#endif /* _MEGACORES_PLL_H_ */
> > \ No newline at end of file
> > diff --git a/drivers/gpu/drm/sprd/sprd_drm.c
> b/drivers/gpu/drm/sprd/sprd_drm.c
> > index ca93be2..5323e23 100644
> > --- a/drivers/gpu/drm/sprd/sprd_drm.c
> > +++ b/drivers/gpu/drm/sprd/sprd_drm.c
> > @@ -197,6 +197,7 @@ static struct platform_driver sprd_drm_driver = {
> > static struct platform_driver *sprd_drm_drivers[] = {
> > &sprd_drm_driver,
> > &sprd_dpu_driver,
> > + &sprd_dsi_driver,
> > };
> >
> > static int __init sprd_drm_init(void)
> > diff --git a/drivers/gpu/drm/sprd/sprd_drm.h
> b/drivers/gpu/drm/sprd/sprd_drm.h
> > index 85d4a8b..95d1b97 100644
> > --- a/drivers/gpu/drm/sprd/sprd_drm.h
> > +++ b/drivers/gpu/drm/sprd/sprd_drm.h
> > @@ -14,5 +14,6 @@ struct sprd_drm {
> > };
> >
> > extern struct platform_driver sprd_dpu_driver;
> > +extern struct platform_driver sprd_dsi_driver;
> >
> > #endif /* _SPRD_DRM_H_ */
> > diff --git a/drivers/gpu/drm/sprd/sprd_dsi.c
> b/drivers/gpu/drm/sprd/sprd_dsi.c
> > new file mode 100644
> > index 0000000..4ebc1aa
> > --- /dev/null
> > +++ b/drivers/gpu/drm/sprd/sprd_dsi.c
> > @@ -0,0 +1,1162 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Copyright (C) 2020 Unisoc Inc.
> > + */
> > +
> > +#include <linux/component.h>
> > +#include <linux/module.h>
> > +#include <linux/of_address.h>
> > +#include <linux/of_device.h>
> > +#include <linux/of_irq.h>
> > +#include <linux/of_graph.h>
> > +#include <video/mipi_display.h>
> > +
> > +#include <drm/drm_atomic_helper.h>
> > +#include <drm/drm_crtc_helper.h>
> > +#include <drm/drm_of.h>
> > +#include <drm/drm_probe_helper.h>
> > +
> > +#include "sprd_drm.h"
> > +#include "sprd_dpu.h"
> > +#include "sprd_dsi.h"
> > +#include "dw_dsi_ctrl.h"
> > +#include "dw_dsi_ctrl_ppi.h"
> > +
> > +#define encoder_to_dsi(encoder) \
> > + container_of(encoder, struct sprd_dsi, encoder)
> > +#define host_to_dsi(host) \
> > + container_of(host, struct sprd_dsi, host)
> > +#define connector_to_dsi(connector) \
> > + container_of(connector, struct sprd_dsi, connector)
> > +
> > +static int regmap_tst_io_write(void *context, u32 reg, u32 val)
> > +{
> > + struct sprd_dsi *dsi = context;
> > + struct dsi_context *ctx = &dsi->ctx;
> > +
> > + if (val > 0xff || reg > 0xff)
> > + return -EINVAL;
> > +
> > + drm_dbg(dsi->drm, "reg = 0x%02x, val = 0x%02x\n", reg, val);
> > +
> > + dsi_phy_test_en(ctx, 1);
> > + dsi_phy_test_din(ctx, reg);
> > + dsi_phy_test_clk(ctx, 1);
> > + dsi_phy_test_clk(ctx, 0);
> > + dsi_phy_test_en(ctx, 0);
> > + dsi_phy_test_din(ctx, val);
> > + dsi_phy_test_clk(ctx, 1);
> > + dsi_phy_test_clk(ctx, 0);
> > +
> > + return 0;
> > +}
> > +
> > +static int regmap_tst_io_read(void *context, u32 reg, u32 *val)
> > +{
> > + struct sprd_dsi *dsi = context;
> > + struct dsi_context *ctx = &dsi->ctx;
> > + int ret;
> > +
> > + if (reg > 0xff)
> > + return -EINVAL;
> > +
> > + dsi_phy_test_en(ctx, 1);
> > + dsi_phy_test_din(ctx, reg);
> > + dsi_phy_test_clk(ctx, 1);
> > + dsi_phy_test_clk(ctx, 0);
> > + dsi_phy_test_en(ctx, 0);
> > +
> > + udelay(1);
> > +
> > + ret = dsi_phy_test_dout(ctx);
> > + if (ret < 0)
> > + return ret;
> > +
> > + *val = ret;
> > +
> > + drm_dbg(dsi->drm, "reg = 0x%02x, val = 0x%02x\n", reg, *val);
> > + return 0;
> > +}
> > +
> > +static struct regmap_bus regmap_tst_io = {
> > + .reg_write = regmap_tst_io_write,
> > + .reg_read = regmap_tst_io_read,
> > +};
> > +
> > +static const struct regmap_config byte_config = {
> > + .reg_bits = 8,
> > + .val_bits = 8,
> > +};
> > +
> > +static int dphy_wait_pll_locked(struct dsi_context *ctx)
> > +{
> > + struct sprd_dsi *dsi = container_of(ctx, struct sprd_dsi, ctx);
> > + int i;
> > +
> > + for (i = 0; i < 50000; i++) {
> > + if (dsi_phy_is_pll_locked(ctx))
> > + return 0;
> > + udelay(3);
> > + }
> > +
> > + drm_err(dsi->drm, "dphy pll can not be locked\n");
> > + return -ETIMEDOUT;
> > +}
> > +
> > +static int dsi_wait_tx_payload_fifo_empty(struct dsi_context *ctx)
> > +{
> > + int i;
> > +
> > + for (i = 0; i < 5000; i++) {
> > + if (dsi_is_tx_payload_fifo_empty(ctx))
> > + return 0;
> > + udelay(1);
> > + }
> > +
> > + return -ETIMEDOUT;
> > +}
> > +
> > +static int dsi_wait_tx_cmd_fifo_empty(struct dsi_context *ctx)
> > +{
> > + int i;
> > +
> > + for (i = 0; i < 5000; i++) {
> > + if (dsi_is_tx_cmd_fifo_empty(ctx))
> > + return 0;
> > + udelay(1);
> > + }
> > +
> > + return -ETIMEDOUT;
> > +}
> > +
> > +static int dsi_wait_rd_resp_completed(struct dsi_context *ctx)
> > +{
> > + int i;
> > +
> > + for (i = 0; i < 10000; i++) {
> > + if (dsi_is_bta_returned(ctx))
> > + return 0;
> > + udelay(10);
> > + }
> > +
> > + return -ETIMEDOUT;
> > +}
> > +
> > +static u16 calc_bytes_per_pixel_x100(int coding)
> > +{
> > + u16 Bpp_x100;
> > +
> > + switch (coding) {
> > + case COLOR_CODE_16BIT_CONFIG1:
> > + case COLOR_CODE_16BIT_CONFIG2:
> > + case COLOR_CODE_16BIT_CONFIG3:
> > + Bpp_x100 = 200;
> > + break;
> > + case COLOR_CODE_18BIT_CONFIG1:
> > + case COLOR_CODE_18BIT_CONFIG2:
> > + Bpp_x100 = 225;
> > + break;
> > + case COLOR_CODE_24BIT:
> > + Bpp_x100 = 300;
> > + break;
> > + case COLOR_CODE_COMPRESSTION:
> > + Bpp_x100 = 100;
> > + break;
> > + case COLOR_CODE_20BIT_YCC422_LOOSELY:
> > + Bpp_x100 = 250;
> > + break;
> > + case COLOR_CODE_24BIT_YCC422:
> > + Bpp_x100 = 300;
> > + break;
> > + case COLOR_CODE_16BIT_YCC422:
> > + Bpp_x100 = 200;
> > + break;
> > + case COLOR_CODE_30BIT:
> > + Bpp_x100 = 375;
> > + break;
> > + case COLOR_CODE_36BIT:
> > + Bpp_x100 = 450;
> > + break;
> > + case COLOR_CODE_12BIT_YCC420:
> > + Bpp_x100 = 150;
> > + break;
> > + default:
> > + DRM_ERROR("invalid color coding");
> > + Bpp_x100 = 0;
> > + break;
> > + }
> > +
> > + return Bpp_x100;
> > +}
> > +
> > +static u8 calc_video_size_step(int coding)
> > +{
> > + u8 video_size_step;
> > +
> > + switch (coding) {
> > + case COLOR_CODE_16BIT_CONFIG1:
> > + case COLOR_CODE_16BIT_CONFIG2:
> > + case COLOR_CODE_16BIT_CONFIG3:
> > + case COLOR_CODE_18BIT_CONFIG1:
> > + case COLOR_CODE_18BIT_CONFIG2:
> > + case COLOR_CODE_24BIT:
> > + case COLOR_CODE_COMPRESSTION:
> > + return video_size_step = 1;
> > + case COLOR_CODE_20BIT_YCC422_LOOSELY:
> > + case COLOR_CODE_24BIT_YCC422:
> > + case COLOR_CODE_16BIT_YCC422:
> > + case COLOR_CODE_30BIT:
> > + case COLOR_CODE_36BIT:
> > + case COLOR_CODE_12BIT_YCC420:
> > + return video_size_step = 2;
> > + default:
> > + DRM_ERROR("invalid color coding");
> > + return 0;
> > + }
> > +}
> > +
> > +static u16 round_video_size(int coding, u16 video_size)
> > +{
> > + switch (coding) {
> > + case COLOR_CODE_16BIT_YCC422:
> > + case COLOR_CODE_24BIT_YCC422:
> > + case COLOR_CODE_20BIT_YCC422_LOOSELY:
> > + case COLOR_CODE_12BIT_YCC420:
> > + /* round up active H pixels to a multiple of 2 */
> > + if ((video_size % 2) != 0)
> > + video_size += 1;
> > + break;
> > + default:
> > + break;
> > + }
> > +
> > + return video_size;
> > +}
> > +
> > +#define SPRD_MIPI_DSI_FMT_DSC 0xff
> > +static u32 fmt_to_coding(u32 fmt)
> > +{
> > + switch (fmt) {
> > + case MIPI_DSI_FMT_RGB565:
> > + return COLOR_CODE_16BIT_CONFIG1;
> > + case MIPI_DSI_FMT_RGB666:
> > + case MIPI_DSI_FMT_RGB666_PACKED:
> > + return COLOR_CODE_18BIT_CONFIG1;
> > + case MIPI_DSI_FMT_RGB888:
> > + return COLOR_CODE_24BIT;
> > + case SPRD_MIPI_DSI_FMT_DSC:
> > + return COLOR_CODE_COMPRESSTION;
> > + default:
> > + DRM_ERROR("Unsupported format (%d)\n", fmt);
> > + return COLOR_CODE_24BIT;
> > + }
> > +}
> > +
> > +#define ns_to_cycle(ns, byte_clk) \
> > + DIV_ROUND_UP((ns) * (byte_clk), 1000000)
> > +
> > +static void sprd_dsi_init(struct dsi_context *ctx)
> > +{
> > + u16 data_hs2lp, data_lp2hs, clk_hs2lp, clk_lp2hs;
> > + u16 max_rd_time;
> > + int div;
> > +
> > + dsi_power_enable(ctx, 0);
> > + dsi_int0_mask(ctx, 0xffffffff);
> > + dsi_int1_mask(ctx, 0xffffffff);
> > + dsi_cmd_mode(ctx);
> > + dsi_eotp_rx_en(ctx, 0);
> > + dsi_eotp_tx_en(ctx, 0);
> > + dsi_ecc_rx_en(ctx, 1);
> > + dsi_crc_rx_en(ctx, 1);
> > + dsi_bta_en(ctx, 1);
> > + dsi_video_vcid(ctx, 0);
> > + dsi_rx_vcid(ctx, 0);
> > +
> > + div = DIV_ROUND_UP(ctx->byte_clk, ctx->esc_clk);
> > + dsi_tx_escape_division(ctx, div);
> > +
> > + max_rd_time = ns_to_cycle(ctx->max_rd_time, ctx->byte_clk);
> > + dsi_max_read_time(ctx, max_rd_time);
> > +
> > + data_hs2lp = ns_to_cycle(ctx->data_hs2lp, ctx->byte_clk);
> > + data_lp2hs = ns_to_cycle(ctx->data_lp2hs, ctx->byte_clk);
> > + clk_hs2lp = ns_to_cycle(ctx->clk_hs2lp, ctx->byte_clk);
> > + clk_lp2hs = ns_to_cycle(ctx->clk_lp2hs, ctx->byte_clk);
> > + dsi_datalane_hs2lp_config(ctx, data_hs2lp);
> > + dsi_datalane_lp2hs_config(ctx, data_lp2hs);
> > + dsi_clklane_hs2lp_config(ctx, clk_hs2lp);
> > + dsi_clklane_lp2hs_config(ctx, clk_lp2hs);
> > +
> > + dsi_power_enable(ctx, 1);
> > +}
> > +
> > +/*
> > + * Free up resources and shutdown host controller and PHY
> > + */
> > +static void sprd_dsi_fini(struct dsi_context *ctx)
> > +{
> > + dsi_int0_mask(ctx, 0xffffffff);
> > + dsi_int1_mask(ctx, 0xffffffff);
> > + dsi_power_enable(ctx, 0);
> > +}
> > +
> > +/*
> > + * If not in burst mode, it will compute the video and null packet sizes
> > + * according to necessity.
> > + * Configure timers for data lanes and/or clock lane to return to LP
> when
> > + * bandwidth is not filled by data.
> > + */
> > +static int sprd_dsi_dpi_video(struct dsi_context *ctx)
> > +{
> > + struct sprd_dsi *dsi = container_of(ctx, struct sprd_dsi, ctx);
> > + struct videomode *vm = &ctx->vm;
> > + u16 Bpp_x100;
> > + u16 video_size;
> > + u32 ratio_x1000;
> > + u16 null_pkt_size = 0;
> > + u8 video_size_step;
> > + u32 hs_to;
> > + u32 total_bytes;
> > + u32 bytes_per_chunk;
> > + u32 chunks = 0;
> > + u32 bytes_left = 0;
> > + u32 chunk_overhead;
> > + const u8 pkt_header = 6;
> > + u8 coding;
> > + int div;
> > + u16 hline;
> > +
> > + coding = fmt_to_coding(ctx->format);
> > + video_size = round_video_size(coding, vm->hactive);
> > + Bpp_x100 = calc_bytes_per_pixel_x100(coding);
> > + video_size_step = calc_video_size_step(coding);
> > + ratio_x1000 = ctx->byte_clk * 1000 / (vm->pixelclock / 1000);
> > + hline = vm->hactive + vm->hsync_len + vm->hfront_porch +
> > + vm->hback_porch;
> > +
> > + dsi_power_enable(ctx, 0);
> > + dsi_dpi_frame_ack_en(ctx, ctx->frame_ack_en);
> > + dsi_dpi_color_coding(ctx, coding);
> > + dsi_dpi_video_burst_mode(ctx, ctx->burst_mode);
> > + dsi_dpi_sig_delay(ctx, 95 * hline * ratio_x1000 / 100000);
> > + dsi_dpi_hline_time(ctx, hline * ratio_x1000 / 1000);
> > + dsi_dpi_hsync_time(ctx, vm->hsync_len * ratio_x1000 / 1000);
> > + dsi_dpi_hbp_time(ctx, vm->hback_porch * ratio_x1000 / 1000);
> > + dsi_dpi_vact(ctx, vm->vactive);
> > + dsi_dpi_vfp(ctx, vm->vfront_porch);
> > + dsi_dpi_vbp(ctx, vm->vback_porch);
> > + dsi_dpi_vsync(ctx, vm->vsync_len);
> > + dsi_dpi_hporch_lp_en(ctx, 1);
> > + dsi_dpi_vporch_lp_en(ctx, 1);
> > +
> > + hs_to = (hline * vm->vactive) + (2 * Bpp_x100) / 100;
> > + for (div = 0x80; (div < hs_to) && (div > 2); div--) {
> > + if ((hs_to % div) == 0) {
> > + dsi_timeout_clock_division(ctx, div);
> > + dsi_lp_rx_timeout(ctx, hs_to / div);
> > + dsi_hs_tx_timeout(ctx, hs_to / div);
> > + break;
> > + }
> > + }
> > +
> > + if (ctx->burst_mode == VIDEO_BURST_WITH_SYNC_PULSES) {
> > + dsi_dpi_video_packet_size(ctx, video_size);
> > + dsi_dpi_null_packet_size(ctx, 0);
> > + dsi_dpi_chunk_num(ctx, 0);
> > + } else {
> > + /* non burst transmission */
> > + null_pkt_size = 0;
> > +
> > + /* bytes to be sent - first as one chunk */
> > + bytes_per_chunk = vm->hactive * Bpp_x100 / 100 +
> pkt_header;
> > +
> > + /* hline total bytes from the DPI interface */
> > + total_bytes = (vm->hactive + vm->hfront_porch) *
> > + ratio_x1000 / ctx->lanes / 1000;
> > +
> > + /* check if the pixels actually fit on the DSI link */
> > + if (total_bytes < bytes_per_chunk) {
> > + drm_err(dsi->drm, "current resolution can not be
> set\n");
> > + return -EINVAL;
> > + }
> > +
> > + chunk_overhead = total_bytes - bytes_per_chunk;
> > +
> > + /* overhead higher than 1 -> enable multi packets */
> > + if (chunk_overhead > 1) {
> > +
> > + /* multi packets */
> > + for (video_size = video_size_step;
> > + video_size < vm->hactive;
> > + video_size += video_size_step) {
> > +
> > + if (vm->hactive * 1000 / video_size % 1000)
> > + continue;
> > +
> > + chunks = vm->hactive / video_size;
> > + bytes_per_chunk = Bpp_x100 * video_size /
> 100
> > + + pkt_header;
> > + if (total_bytes >= (bytes_per_chunk *
> chunks)) {
> > + bytes_left = total_bytes -
> > + bytes_per_chunk *
> chunks;
> > + break;
> > + }
> > + }
> > +
> > + /* prevent overflow (unsigned - unsigned) */
> > + if (bytes_left > (pkt_header * chunks)) {
> > + null_pkt_size = (bytes_left -
> > + pkt_header * chunks) /
> chunks;
> > + /* avoid register overflow */
> > + if (null_pkt_size > 1023)
> > + null_pkt_size = 1023;
> > + }
> > +
> > + } else {
> > +
> > + /* single packet */
> > + chunks = 1;
> > +
> > + /* must be a multiple of 4 except 18 loosely */
> > + for (video_size = vm->hactive;
> > + (video_size % video_size_step) != 0;
> > + video_size++)
> > + ;
> > + }
> > +
> > + dsi_dpi_video_packet_size(ctx, video_size);
> > + dsi_dpi_null_packet_size(ctx, null_pkt_size);
> > + dsi_dpi_chunk_num(ctx, chunks);
> > + }
> > +
> > + dsi_int0_mask(ctx, ctx->int0_mask);
> > + dsi_int1_mask(ctx, ctx->int1_mask);
> > + dsi_power_enable(ctx, 1);
> > +
> > + return 0;
> > +}
> > +
> > +static void sprd_dsi_edpi_video(struct dsi_context *ctx)
> > +{
> > + const u32 fifo_depth = 1096;
> > + const u32 word_length = 4;
> > + u32 hactive = ctx->vm.hactive;
> > + u32 Bpp_x100;
> > + u32 max_fifo_len;
> > + u8 coding;
> > +
> > + coding = fmt_to_coding(ctx->format);
> > + Bpp_x100 = calc_bytes_per_pixel_x100(coding);
> > + max_fifo_len = word_length * fifo_depth * 100 / Bpp_x100;
> > +
> > + dsi_power_enable(ctx, 0);
> > + dsi_dpi_color_coding(ctx, coding);
> > + dsi_tear_effect_ack_en(ctx, ctx->te_ack_en);
> > +
> > + if (max_fifo_len > hactive)
> > + dsi_edpi_max_pkt_size(ctx, hactive);
> > + else
> > + dsi_edpi_max_pkt_size(ctx, max_fifo_len);
> > +
> > + dsi_int0_mask(ctx, ctx->int0_mask);
> > + dsi_int1_mask(ctx, ctx->int1_mask);
> > + dsi_power_enable(ctx, 1);
> > +}
> > +
> > +/*
> > + * Send a packet on the generic interface,
> > + * this function has an active delay to wait for the buffer to clear.
> > + * The delay is limited to:
> > + * (param_length / 4) x DSIH_FIFO_ACTIVE_WAIT x register access time
> > + * the controller restricts the sending of.
> > + *
> > + * This function will not be able to send Null and Blanking packets due
> to
> > + * controller restriction
> > + */
> > +static int sprd_dsi_wr_pkt(struct dsi_context *ctx, u8 vc, u8 type,
> > + const u8 *param, u16 len)
> > +{
> > + struct sprd_dsi *dsi = container_of(ctx, struct sprd_dsi, ctx);
> > + u8 wc_lsbyte, wc_msbyte;
> > + u32 payload;
> > + int i, j, ret;
> > +
> > + if (vc > 3)
> > + return -EINVAL;
> > +
> > +
> > + /* 1st: for long packet, must config payload first */
> > + ret = dsi_wait_tx_payload_fifo_empty(ctx);
> > + if (ret) {
> > + drm_err(dsi->drm, "tx payload fifo is not empty\n");
> > + return ret;
> > + }
> > +
> > + if (len > 2) {
> > + for (i = 0, j = 0; i < len; i += j) {
> > + payload = 0;
> > + for (j = 0; (j < 4) && ((j + i) < (len)); j++)
> > + payload |= param[i + j] << (j * 8);
> > +
> > + dsi_set_packet_payload(ctx, payload);
> > + }
> > + wc_lsbyte = len & 0xff;
> > + wc_msbyte = len >> 8;
> > + } else {
> > + wc_lsbyte = (len > 0) ? param[0] : 0;
> > + wc_msbyte = (len > 1) ? param[1] : 0;
> > + }
> > +
> > + /* 2nd: then set packet header */
> > + ret = dsi_wait_tx_cmd_fifo_empty(ctx);
> > + if (ret) {
> > + drm_err(dsi->drm, "tx cmd fifo is not empty\n");
> > + return ret;
> > + }
> > +
> > + dsi_set_packet_header(ctx, vc, type, wc_lsbyte, wc_msbyte);
> > +
> > + return 0;
> > +}
> > +
> > +/*
> > + * Send READ packet to peripheral using the generic interface,
> > + * this will force command mode and stop video mode (because of BTA).
> > + *
> > + * This function has an active delay to wait for the buffer to clear,
> > + * the delay is limited to 2 x DSIH_FIFO_ACTIVE_WAIT
> > + * (waiting for command buffer, and waiting for receiving)
> > + * @note this function will enable BTA
> > + */
> > +static int sprd_dsi_rd_pkt(struct dsi_context *ctx, u8 vc, u8 type,
> > + u8 msb_byte, u8 lsb_byte,
> > + u8 *buffer, u8 bytes_to_read)
> > +{
> > + struct sprd_dsi *dsi = container_of(ctx, struct sprd_dsi, ctx);
> > + int i, ret;
> > + int count = 0;
> > + u32 temp;
> > +
> > + if (vc > 3)
> > + return -EINVAL;
> > +
> > + /* 1st: send read command to peripheral */
> > + if (!dsi_is_tx_cmd_fifo_empty(ctx))
> > + return -EIO;
> > +
> > + dsi_set_packet_header(ctx, vc, type, lsb_byte, msb_byte);
> > +
> > + /* 2nd: wait peripheral response completed */
> > + ret = dsi_wait_rd_resp_completed(ctx);
> > + if (ret) {
> > + drm_err(dsi->drm, "wait read response time out\n");
> > + return ret;
> > + }
> > +
> > + /* 3rd: get data from rx payload fifo */
> > + if (dsi_is_rx_payload_fifo_empty(ctx)) {
> > + drm_err(dsi->drm, "rx payload fifo empty\n");
> > + return -EIO;
> > + }
> > +
> > + for (i = 0; i < 100; i++) {
> > + temp = dsi_get_rx_payload(ctx);
> > +
> > + if (count < bytes_to_read)
> > + buffer[count++] = temp & 0xff;
> > + if (count < bytes_to_read)
> > + buffer[count++] = (temp >> 8) & 0xff;
> > + if (count < bytes_to_read)
> > + buffer[count++] = (temp >> 16) & 0xff;
> > + if (count < bytes_to_read)
> > + buffer[count++] = (temp >> 24) & 0xff;
> > +
> > + if (dsi_is_rx_payload_fifo_empty(ctx))
> > + return count;
> > + else {
> > + drm_err(dsi->drm, "read too many buffers\n");
> > + return -EIO;
> > + }
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static void sprd_dsi_set_work_mode(struct dsi_context *ctx, u8 mode)
> > +{
> > + if (mode == DSI_MODE_CMD)
> > + dsi_cmd_mode(ctx);
> > + else
> > + dsi_video_mode(ctx);
> > +}
> > +
> > +static void sprd_dsi_lp_cmd_enable(struct dsi_context *ctx, bool enable)
> > +{
> > + if (dsi_is_cmd_mode(ctx))
> > + dsi_cmd_mode_lp_cmd_en(ctx, enable);
> > + else
> > + dsi_video_mode_lp_cmd_en(ctx, enable);
> > +}
> > +
> > +static void sprd_dsi_state_reset(struct dsi_context *ctx)
> > +{
> > + dsi_power_enable(ctx, 0);
> > + udelay(100);
> > + dsi_power_enable(ctx, 1);
> > +}
> > +
> > +static u32 sprd_dsi_int_status(struct dsi_context *ctx, int index)
> > +{
> > + struct sprd_dsi *dsi = container_of(ctx, struct sprd_dsi, ctx);
> > + u32 status;
> > +
> > + if (0 == index)
> > + status = dsi_int0_status(ctx);
> > + else if (1 == index)
> > + status = dsi_int1_status(ctx);
> > + else {
> > + drm_err(dsi->drm, "invalid dsi IRQ index %d\n", index);
> > + status = -EINVAL;
> > + }
> > +
> > + return status;
> > +}
> > +
> > +static int sprd_dphy_init(struct dsi_context *ctx)
> > +{
> > + struct sprd_dsi *dsi = container_of(ctx, struct sprd_dsi, ctx);
> > + int ret;
> > +
> > + dsi_phy_rstz(ctx, 0);
> > + dsi_phy_shutdownz(ctx, 0);
> > + dsi_phy_clklane_en(ctx, 0);
> > +
> > + dsi_phy_test_clr(ctx, 0);
> > + dsi_phy_test_clr(ctx, 1);
> > + dsi_phy_test_clr(ctx, 0);
> > +
> > + dphy_pll_config(ctx);
> > + dphy_timing_config(ctx);
> > +
> > + dsi_phy_shutdownz(ctx, 1);
> > + dsi_phy_rstz(ctx, 1);
> > + dsi_phy_stop_wait_time(ctx, 0x1C);
> > + dsi_phy_clklane_en(ctx, 1);
> > + dsi_phy_datalane_en(ctx);
> > +
> > + ret = dphy_wait_pll_locked(ctx);
> > + if (ret) {
> > + drm_err(dsi->drm, "dphy initial failed\n");
> > + return ret;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static void sprd_dphy_fini(struct dsi_context *ctx)
> > +{
> > + dsi_phy_rstz(ctx, 0);
> > + dsi_phy_shutdownz(ctx, 0);
> > + dsi_phy_rstz(ctx, 1);
> > +}
> > +
> > +static void sprd_dsi_encoder_enable(struct drm_encoder *encoder)
> > +{
> > + struct sprd_dsi *dsi = encoder_to_dsi(encoder);
> > + struct sprd_dpu *dpu = to_sprd_crtc(encoder->crtc);
> > + struct dsi_context *ctx = &dsi->ctx;
> > +
> > + if (ctx->enabled) {
> > + drm_warn(dsi->drm, "dsi is initialized\n");
> > + return;
> > + }
> > +
> > + sprd_dsi_init(ctx);
> > + if (ctx->work_mode == DSI_MODE_VIDEO)
> > + sprd_dsi_dpi_video(ctx);
> > + else
> > + sprd_dsi_edpi_video(ctx);
> > +
> > + sprd_dphy_init(ctx);
> > +
> > + sprd_dsi_lp_cmd_enable(ctx, true);
> > +
> > + if (dsi->panel) {
> > + drm_panel_prepare(dsi->panel);
> > + drm_panel_enable(dsi->panel);
> > + }
> > +
> > + sprd_dsi_set_work_mode(ctx, ctx->work_mode);
> > + sprd_dsi_state_reset(ctx);
> > +
> > + if (ctx->nc_clk_en)
> > + dsi_nc_clk_en(ctx, true);
> > + else {
> > + dsi_phy_clk_hs_rqst(ctx, true);
> > + dphy_wait_pll_locked(ctx);
> > + }
> > +
> > + sprd_dpu_run(dpu);
> > +
> > + ctx->enabled = true;
> > +}
> > +
> > +static void sprd_dsi_encoder_disable(struct drm_encoder *encoder)
> > +{
> > + struct sprd_dsi *dsi = encoder_to_dsi(encoder);
> > + struct sprd_dpu *dpu = to_sprd_crtc(encoder->crtc);
> > + struct dsi_context *ctx = &dsi->ctx;
> > +
> > + if (!ctx->enabled) {
> > + drm_warn(dsi->drm, "dsi isn't initialized\n");
> > + return;
> > + }
> > +
> > + sprd_dpu_stop(dpu);
> > + sprd_dsi_set_work_mode(ctx, DSI_MODE_CMD);
> > + sprd_dsi_lp_cmd_enable(ctx, true);
> > +
> > + if (dsi->panel) {
> > + drm_panel_disable(dsi->panel);
> > + drm_panel_unprepare(dsi->panel);
> > + }
> > +
> > + sprd_dphy_fini(ctx);
> > + sprd_dsi_fini(ctx);
> > +
> > + ctx->enabled = false;
> > +}
> > +
> > +static void sprd_dsi_encoder_mode_set(struct drm_encoder *encoder,
> > + struct drm_display_mode *mode,
> > + struct drm_display_mode *adj_mode)
> > +{
> > + struct sprd_dsi *dsi = encoder_to_dsi(encoder);
> > +
> > + drm_dbg(dsi->drm, "%s() set mode: %s\n", __func__,
> dsi->mode->name);
> > +}
> > +
> > +static int sprd_dsi_encoder_atomic_check(struct drm_encoder *encoder,
> > + struct drm_crtc_state *crtc_state,
> > + struct drm_connector_state *conn_state)
> > +{
> > + return 0;
> > +}
> > +
> > +static const struct drm_encoder_helper_funcs sprd_encoder_helper_funcs
> = {
> > + .atomic_check = sprd_dsi_encoder_atomic_check,
> > + .mode_set = sprd_dsi_encoder_mode_set,
> > + .enable = sprd_dsi_encoder_enable,
> > + .disable = sprd_dsi_encoder_disable
> > +};
> > +
> > +static const struct drm_encoder_funcs sprd_encoder_funcs = {
> > + .destroy = drm_encoder_cleanup,
> > +};
> > +
> > +static int sprd_dsi_encoder_init(struct drm_device *drm,
> > + struct sprd_dsi *dsi)
> > +{
> > + struct drm_encoder *encoder = &dsi->encoder;
> > + struct device *dev = dsi->host.dev;
> > + u32 crtc_mask;
> > + int ret;
> > +
> > + crtc_mask = drm_of_find_possible_crtcs(drm, dev->of_node);
> > + if (!crtc_mask) {
> > + drm_err(drm, "failed to find crtc mask\n");
> > + return -EINVAL;
> > + }
> > +
> > + drm_dbg(dsi->drm, "find possible crtcs: 0x%08x\n", crtc_mask);
> > +
> > + encoder->possible_crtcs = crtc_mask;
> > + ret = drm_encoder_init(drm, encoder, &sprd_encoder_funcs,
> > + DRM_MODE_ENCODER_DSI, NULL);
> > + if (ret) {
> > + drm_err(drm, "failed to init dsi encoder\n");
> > + return ret;
> > + }
> > +
> > + drm_encoder_helper_add(encoder, &sprd_encoder_helper_funcs);
> > +
> > + return 0;
> > +}
> > +
> > +static int sprd_dsi_find_panel(struct sprd_dsi *dsi)
> > +{
> > + struct device *dev = dsi->host.dev;
> > + struct device_node *child, *lcds_node;
> > + struct drm_panel *panel;
> > +
> > + /* search /lcds child node first */
> > + lcds_node = of_find_node_by_path("/lcds");
> > + for_each_child_of_node(lcds_node, child) {
> > + panel = of_drm_find_panel(child);
> > + if (!IS_ERR(panel)) {
> > + dsi->panel = panel;
> > + return 0;
> > + }
> > + }
> > +
> > + /*
> > + * If /lcds child node search failed, we search
> > + * the child of dsi host node.
> > + */
> > + for_each_child_of_node(dev->of_node, child) {
> > + panel = of_drm_find_panel(child);
> > + if (!IS_ERR(panel)) {
> > + dsi->panel = panel;
> > + return 0;
> > + }
> > + }
> > +
> > + drm_err(dsi->drm, "of_drm_find_panel() failed\n");
> > + return -ENODEV;
> > +}
> > +
> > +static int sprd_dsi_host_attach(struct mipi_dsi_host *host,
> > + struct mipi_dsi_device *slave)
> > +{
> > + struct sprd_dsi *dsi = host_to_dsi(host);
> > + struct dsi_context *ctx = &dsi->ctx;
> > + int ret;
> > +
> > + dsi->slave = slave;
> > + ctx->lanes = slave->lanes;
> > + ctx->format = slave->format;
> > + ctx->byte_clk = slave->hs_rate / 8;
> > + ctx->esc_clk = slave->lp_rate;
> > +
> > + if (slave->mode_flags & MIPI_DSI_MODE_VIDEO)
> > + ctx->work_mode = DSI_MODE_VIDEO;
> > + else
> > + ctx->work_mode = DSI_MODE_CMD;
> > +
> > + if (slave->mode_flags & MIPI_DSI_MODE_VIDEO_BURST)
> > + ctx->burst_mode = VIDEO_BURST_WITH_SYNC_PULSES;
> > + else if (slave->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE)
> > + ctx->burst_mode = VIDEO_NON_BURST_WITH_SYNC_PULSES;
> > + else
> > + ctx->burst_mode = VIDEO_NON_BURST_WITH_SYNC_EVENTS;
> > +
> > + if (slave->mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS)
> > + ctx->nc_clk_en = true;
> > +
> > + ret = sprd_dsi_find_panel(dsi);
> > + if (ret)
> > + return ret;
> > +
> > + return 0;
> > +}
> > +
> > +static int sprd_dsi_host_detach(struct mipi_dsi_host *host,
> > + struct mipi_dsi_device *slave)
> > +{
> > + /* do nothing */
> > + return 0;
> > +}
> > +
> > +static ssize_t sprd_dsi_host_transfer(struct mipi_dsi_host *host,
> > + const struct mipi_dsi_msg *msg)
> > +{
> > + struct sprd_dsi *dsi = host_to_dsi(host);
> > + const u8 *tx_buf = msg->tx_buf;
> > +
> > + if (msg->rx_buf && msg->rx_len) {
> > + u8 lsb = (msg->tx_len > 0) ? tx_buf[0] : 0;
> > + u8 msb = (msg->tx_len > 1) ? tx_buf[1] : 0;
> > +
> > + return sprd_dsi_rd_pkt(&dsi->ctx, msg->channel, msg->type,
> > + msb, lsb, msg->rx_buf, msg->rx_len);
> > + }
> > +
> > + if (msg->tx_buf && msg->tx_len)
> > + return sprd_dsi_wr_pkt(&dsi->ctx, msg->channel, msg->type,
> > + tx_buf, msg->tx_len);
> > +
> > + return 0;
> > +}
> > +
> > +static const struct mipi_dsi_host_ops sprd_dsi_host_ops = {
> > + .attach = sprd_dsi_host_attach,
> > + .detach = sprd_dsi_host_detach,
> > + .transfer = sprd_dsi_host_transfer,
> > +};
> > +
> > +static int sprd_dsi_host_init(struct sprd_dsi *dsi, struct device *dev)
> > +{
> > + int ret;
> > +
> > + dsi->host.dev = dev;
> > + dsi->host.ops = &sprd_dsi_host_ops;
> > +
> > + ret = mipi_dsi_host_register(&dsi->host);
> > + if (ret)
> > + drm_err(dsi->drm, "failed to register dsi host\n");
> > +
> > + return ret;
> > +}
> > +
> > +static int sprd_dsi_connector_get_modes(struct drm_connector *connector)
> > +{
> > + struct sprd_dsi *dsi = connector_to_dsi(connector);
> > +
> > + return drm_panel_get_modes(dsi->panel, connector);
> > +}
> > +
> > +static enum drm_mode_status
> > +sprd_dsi_connector_mode_valid(struct drm_connector *connector,
> > + struct drm_display_mode *mode)
> > +{
> > + struct sprd_dsi *dsi = connector_to_dsi(connector);
> > +
> > + drm_dbg(dsi->drm, "%s() mode: "DRM_MODE_FMT"\n", __func__,
> DRM_MODE_ARG(mode));
> > +
> > + if (mode->type & DRM_MODE_TYPE_PREFERRED) {
> > + dsi->mode = mode;
> > + drm_display_mode_to_videomode(dsi->mode, &dsi->ctx.vm);
> > + }
> > +
> > + return MODE_OK;
> > +}
> > +
> > +static struct drm_encoder *
> > +sprd_dsi_connector_best_encoder(struct drm_connector *connector)
> > +{
> > + struct sprd_dsi *dsi = connector_to_dsi(connector);
> > +
> > + return &dsi->encoder;
> > +}
> > +
> > +static struct drm_connector_helper_funcs
> sprd_dsi_connector_helper_funcs = {
> > + .get_modes = sprd_dsi_connector_get_modes,
> > + .mode_valid = sprd_dsi_connector_mode_valid,
> > + .best_encoder = sprd_dsi_connector_best_encoder,
> > +};
> > +
> > +static enum drm_connector_status
> > +sprd_dsi_connector_detect(struct drm_connector *connector, bool force)
> > +{
> > + struct sprd_dsi *dsi = connector_to_dsi(connector);
> > +
> > + if (dsi->panel) {
> > + drm_panel_add(dsi->panel);
> > + return connector_status_connected;
> > + }
> > +
> > + return connector_status_disconnected;
> > +}
> > +
> > +static void sprd_dsi_connector_destroy(struct drm_connector *connector)
> > +{
> > + drm_connector_unregister(connector);
> > + drm_connector_cleanup(connector);
> > +}
> > +
> > +static const struct drm_connector_funcs sprd_dsi_atomic_connector_funcs
> = {
> > + .fill_modes = drm_helper_probe_single_connector_modes,
> > + .detect = sprd_dsi_connector_detect,
> > + .destroy = sprd_dsi_connector_destroy,
> > + .reset = drm_atomic_helper_connector_reset,
> > + .atomic_duplicate_state =
> drm_atomic_helper_connector_duplicate_state,
> > + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
> > +};
> > +
> > +static int sprd_dsi_connector_init(struct drm_device *drm, struct
> sprd_dsi *dsi)
> > +{
> > + struct drm_encoder *encoder = &dsi->encoder;
> > + struct drm_connector *connector = &dsi->connector;
> > + int ret;
> > +
> > + connector->polled = DRM_CONNECTOR_POLL_HPD;
> > +
> > + ret = drm_connector_init(drm, connector,
> > + &sprd_dsi_atomic_connector_funcs,
> > + DRM_MODE_CONNECTOR_DSI);
> > + if (ret) {
> > + drm_err(drm, "drm_connector_init() failed\n");
> > + return ret;
> > + }
> > +
> > + drm_connector_helper_add(connector,
> > + &sprd_dsi_connector_helper_funcs);
> > +
> > + drm_connector_attach_encoder(connector, encoder);
> > +
> > + return 0;
> > +}
> > +
> > +static irqreturn_t sprd_dsi_isr(int irq, void *data)
> > +{
> > + struct sprd_dsi *dsi = data;
> > + u32 status = 0;
> > +
> > + if (dsi->ctx.irq0 == irq)
> > + status = sprd_dsi_int_status(&dsi->ctx, 0);
> > + else if (dsi->ctx.irq1 == irq)
> > + status = sprd_dsi_int_status(&dsi->ctx, 1);
> > +
> > + if (status & DSI_INT_STS_NEED_SOFT_RESET)
> > + sprd_dsi_state_reset(&dsi->ctx);
> > +
> > + return IRQ_HANDLED;
> > +}
> > +
> > +static int sprd_dsi_bind(struct device *dev, struct device *master,
> void *data)
> > +{
> > + struct drm_device *drm = data;
> > + struct sprd_dsi *dsi = dev_get_drvdata(dev);
> > + int ret;
> > +
> > + ret = sprd_dsi_encoder_init(drm, dsi);
> > + if (ret)
> > + goto cleanup_host;
> > +
> > + ret = sprd_dsi_connector_init(drm, dsi);
> > + if (ret)
> > + goto cleanup_encoder;
> > +
> > + dsi->drm = drm;
> > +
> > + return 0;
> > +
> > +cleanup_encoder:
> > + drm_encoder_cleanup(&dsi->encoder);
> > +cleanup_host:
> > + mipi_dsi_host_unregister(&dsi->host);
> > + return ret;
> > +}
> > +
> > +static void sprd_dsi_unbind(struct device *dev,
> > + struct device *master, void *data)
> > +{
> > + struct drm_device *drm = data;
> > +
> > + /* do nothing */
> > + drm_dbg(drm, "%s()\n", __func__);
> > +
> > +}
> > +
> > +static const struct component_ops dsi_component_ops = {
> > + .bind = sprd_dsi_bind,
> > + .unbind = sprd_dsi_unbind,
> > +};
> > +
> > +static int sprd_dsi_context_init(struct sprd_dsi *dsi,
> > + struct device *dev)
> > +{
> > + struct platform_device *pdev = to_platform_device(dev);
> > + struct dsi_context *ctx = &dsi->ctx;
> > + struct resource *res;
> > + int ret;
> > +
> > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > + ctx->base = devm_ioremap(dev, res->start, resource_size(res));
> > + if (!ctx->base) {
> > + drm_err(dsi->drm, "failed to map dsi host registers\n");
> > + return -ENXIO;
> > + }
> > +
> > + ctx->pll = devm_kzalloc(dev, sizeof(*ctx->pll), GFP_KERNEL);
>
> You probably want to use drmm_kzalloc here, just to be on the safe side.
>
> > + if (!ctx->pll) {
> > + drm_err(dsi->drm, "failed to allocate dphy pll data.\n");
> > + return -ENOMEM;
> > + }
> > +
> > + ctx->regmap = devm_regmap_init(dev, ®map_tst_io, dsi,
> &byte_config);
> > + if (IS_ERR(ctx->regmap)) {
> > + drm_err(dsi->drm, "dphy regmap init failed\n");
> > + return PTR_ERR(ctx->regmap);
> > + }
> > +
> > + ctx->irq0 = platform_get_irq(pdev, 0);
> > + if (ctx->irq0 > 0) {
> > + ret = request_irq(ctx->irq0, sprd_dsi_isr, 0, "DSI_INT0",
> dsi);
> > + if (ret) {
> > + drm_err(dsi->drm, "failed to request dsi irq
> int0!\n");
> > + return -EINVAL;
> > + }
> > + }
> > +
> > + ctx->irq1 = platform_get_irq(pdev, 1);
> > + if (ctx->irq1 > 0) {
> > + ret = request_irq(ctx->irq1, sprd_dsi_isr, 0, "DSI_INT1",
> dsi);
> > + if (ret) {
> > + drm_err(dsi->drm, "failed to request dsi irq
> int1!\n");
> > + return -EINVAL;
> > + }
> > + }
> > +
> > + ctx->data_hs2lp = 120;
> > + ctx->data_lp2hs = 500;
> > + ctx->clk_hs2lp = 4;
> > + ctx->clk_lp2hs = 15;
> > + ctx->max_rd_time = 6000;
> > + ctx->int0_mask = 0xffffffff;
> > + ctx->int1_mask = 0xffffffff;
> > +
> > + dsi->ctx.enabled = true;
> > +
> > + return 0;
> > +}
> > +
> > +static const struct of_device_id dsi_match_table[] = {
> > + { .compatible = "sprd,sharkl3-dsi-host" },
> > + { /* sentinel */ },
> > +};
> > +
> > +static int sprd_dsi_probe(struct platform_device *pdev)
> > +{
> > + struct sprd_dsi *dsi;
> > + int ret;
> > +
> > + dsi = kzalloc(sizeof(*dsi), GFP_KERNEL);
> > + if (!dsi) {
> > + dev_err(&pdev->dev, "failed to allocate dsi data.\n");
> > + return -ENOMEM;
> > + }
> > +
> > + dsi->dev = &pdev->dev;
> > +
> > + ret = sprd_dsi_context_init(dsi, &pdev->dev);
> > + if (ret)
> > + goto err;
> > +
> > + ret = sprd_dsi_host_init(dsi, &pdev->dev);
> > + if (ret)
> > + goto err;
>
> Same comment as with the previous patch for planes/crtc: If you move this
> into the bind function then you can use the drmm_ functions and ditch the
> kfree.
>
> > +
> > + platform_set_drvdata(pdev, dsi);
> > +
> > + return component_add(&pdev->dev, &dsi_component_ops);
> > +
> > +err:
> > + kfree(dsi);
> > + return ret;
> > +}
> > +
> > +static int sprd_dsi_remove(struct platform_device *pdev)
> > +{
> > + struct sprd_dsi *dsi = platform_get_drvdata(pdev);
> > +
> > + component_del(&pdev->dev, &dsi_component_ops);
> > +
> > + kfree(dsi);
> > + return 0;
> > +}
> > +
> > +struct platform_driver sprd_dsi_driver = {
> > + .probe = sprd_dsi_probe,
> > + .remove = sprd_dsi_remove,
> > + .driver = {
> > + .name = "sprd-dsi-drv",
> > + .of_match_table = dsi_match_table,
> > + },
> > +};
> > +
> > +MODULE_AUTHOR("Leon He <leon.he at unisoc.com>");
> > +MODULE_AUTHOR("Kevin Tang <kevin.tang at unisoc.com>");
> > +MODULE_DESCRIPTION("Unisoc MIPI DSI HOST Controller Driver");
> > +MODULE_LICENSE("GPL v2");
> > diff --git a/drivers/gpu/drm/sprd/sprd_dsi.h
> b/drivers/gpu/drm/sprd/sprd_dsi.h
> > new file mode 100644
> > index 0000000..e07cd12
> > --- /dev/null
> > +++ b/drivers/gpu/drm/sprd/sprd_dsi.h
> > @@ -0,0 +1,107 @@
> > +/* SPDX-License-Identifier: GPL-2.0 */
> > +/*
> > + * Copyright (C) 2020 Unisoc Inc.
> > + */
> > +
> > +#ifndef __SPRD_DSI_H__
> > +#define __SPRD_DSI_H__
> > +
> > +#include <linux/of.h>
> > +#include <linux/device.h>
> > +#include <linux/regmap.h>
> > +#include <video/videomode.h>
> > +
> > +#include <drm/drm_bridge.h>
> > +#include <drm/drm_connector.h>
> > +#include <drm/drm_encoder.h>
> > +#include <drm/drm_mipi_dsi.h>
> > +#include <drm/drm_print.h>
> > +#include <drm/drm_panel.h>
> > +
> > +#include "megacores_pll.h"
> > +
> > +#define DSI_INT_STS_NEED_SOFT_RESET BIT(0)
> > +#define DSI_INT_STS_NEED_HARD_RESET BIT(1)
> > +
> > +enum dsi_work_mode {
> > + DSI_MODE_CMD = 0,
> > + DSI_MODE_VIDEO
> > +};
> > +
> > +enum video_burst_mode {
> > + VIDEO_NON_BURST_WITH_SYNC_PULSES = 0,
> > + VIDEO_NON_BURST_WITH_SYNC_EVENTS,
> > + VIDEO_BURST_WITH_SYNC_PULSES
> > +};
> > +
> > +enum dsi_color_coding {
> > + COLOR_CODE_16BIT_CONFIG1 = 0,
> > + COLOR_CODE_16BIT_CONFIG2,
> > + COLOR_CODE_16BIT_CONFIG3,
> > + COLOR_CODE_18BIT_CONFIG1,
> > + COLOR_CODE_18BIT_CONFIG2,
> > + COLOR_CODE_24BIT,
> > + COLOR_CODE_20BIT_YCC422_LOOSELY,
> > + COLOR_CODE_24BIT_YCC422,
> > + COLOR_CODE_16BIT_YCC422,
> > + COLOR_CODE_30BIT,
> > + COLOR_CODE_36BIT,
> > + COLOR_CODE_12BIT_YCC420,
> > + COLOR_CODE_COMPRESSTION,
> > + COLOR_CODE_MAX
> > +};
> > +
> > +struct dsi_context {
> > + void __iomem *base;
> > + struct regmap *regmap;
> > + struct dphy_pll *pll;
> > + struct videomode vm;
> > + bool enabled;
> > +
> > + u8 lanes;
> > + u32 format;
> > + u8 work_mode;
> > + u8 burst_mode;
> > +
> > + int irq0;
> > + int irq1;
> > + u32 int0_mask;
> > + u32 int1_mask;
> > +
> > + /* byte clock [KHz] */
> > + u32 byte_clk;
> > + /* escape clock [KHz] */
> > + u32 esc_clk;
> > + /* maximum time (ns) for data lanes from HS to LP */
> > + u16 data_hs2lp;
> > + /* maximum time (ns) for data lanes from LP to HS */
> > + u16 data_lp2hs;
> > + /* maximum time (ns) for clk lanes from HS to LP */
> > + u16 clk_hs2lp;
> > + /* maximum time (ns) for clk lanes from LP to HS */
> > + u16 clk_lp2hs;
> > + /* maximum time (ns) for BTA operation - REQUIRED */
> > + u16 max_rd_time;
> > + /* is 18-bit loosely packets (valid only when BPP == 18) */
> > + bool is_18_loosely;
> > + /* enable receiving frame ack packets - for video mode */
> > + bool frame_ack_en;
> > + /* enable receiving tear effect ack packets - for cmd mode */
> > + bool te_ack_en;
> > + /* enable non coninuous clock for energy saving */
> > + bool nc_clk_en;
> > +};
> > +
> > +struct sprd_dsi {
> > + struct device *dev;
> > + struct drm_device *drm;
> > + struct mipi_dsi_host host;
> > + struct mipi_dsi_device *slave;
> > + struct drm_encoder encoder;
> > + struct drm_connector connector;
> > + struct drm_panel *panel;
> > + struct drm_display_mode *mode;
> > + struct dsi_context ctx;
> > +};
> > +
> > +#endif /* __SPRD_DSI_H__ */
> > --
> > 2.7.4
> >
>
> --
> Daniel Vetter
> Software Engineer, Intel Corporation
> http://blog.ffwll.ch
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://lists.freedesktop.org/archives/dri-devel/attachments/20210211/d6f479a4/attachment-0001.htm>
More information about the dri-devel
mailing list