[Intel-gfx] [PATCH 45/53] drm/i915/dg2: Update modeset sequences
Jani Nikula
jani.nikula at linux.intel.com
Fri Jul 2 08:16:18 UTC 2021
On Thu, 01 Jul 2021, Matt Roper <matthew.d.roper at intel.com> wrote:
> DG2 has some changes to the expected modesetting sequences when compared
> to gen12. Adjust our driver logic accordingly. Although the DP
> sequence is pretty similar to TGL's, there are some steps that change,
> so let's split the handling for that out into a separate function.
>
> Bspec: 54128
> Cc: Lucas De Marchi <lucas.demarchi at intel.com>
> Cc: Anusha Srivatsa <anusha.srivatsa at intel.com>
> Signed-off-by: Matt Roper <matthew.d.roper at intel.com>
> ---
> drivers/gpu/drm/i915/display/intel_ddi.c | 135 +++++++++++++++++++++--
> 1 file changed, 127 insertions(+), 8 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/display/intel_ddi.c b/drivers/gpu/drm/i915/display/intel_ddi.c
> index ade03cf41caa..5499a2975a0e 100644
> --- a/drivers/gpu/drm/i915/display/intel_ddi.c
> +++ b/drivers/gpu/drm/i915/display/intel_ddi.c
> @@ -172,14 +172,22 @@ void intel_wait_ddi_buf_idle(struct drm_i915_private *dev_priv,
> static void intel_wait_ddi_buf_active(struct drm_i915_private *dev_priv,
> enum port port)
> {
> + int ret;
> +
> /* Wait > 518 usecs for DDI_BUF_CTL to be non idle */
> if (DISPLAY_VER(dev_priv) < 10) {
> usleep_range(518, 1000);
> return;
> }
>
> - if (wait_for_us(!(intel_de_read(dev_priv, DDI_BUF_CTL(port)) &
> - DDI_BUF_IS_IDLE), 500))
> + if (IS_DG2(dev_priv))
> + ret = wait_for_us(!(intel_de_read(dev_priv, DDI_BUF_CTL(port)) &
> + DDI_BUF_IS_IDLE), 1200);
> + else
> + ret = wait_for_us(!(intel_de_read(dev_priv, DDI_BUF_CTL(port)) &
> + DDI_BUF_IS_IDLE), 500);
Nitpick, this should really parametetrized the delay, 500 vs. 1200, not
add duplicate the code.
BR,
Jani.
> +
> + if (ret)
> drm_err(&dev_priv->drm, "Timeout waiting for DDI BUF %c to get active\n",
> port_name(port));
> }
> @@ -2207,7 +2215,7 @@ void intel_ddi_sanitize_encoder_pll_mapping(struct intel_encoder *encoder)
> ddi_clk_needed = false;
> }
>
> - if (ddi_clk_needed || !encoder->disable_clock ||
> + if (ddi_clk_needed || !encoder->is_clock_enabled ||
> !encoder->is_clock_enabled(encoder))
> return;
>
> @@ -2488,6 +2496,116 @@ static void intel_ddi_mso_configure(const struct intel_crtc_state *crtc_state)
> OVERLAP_PIXELS_MASK, dss1);
> }
>
> +static void dg2_ddi_pre_enable_dp(struct intel_atomic_state *state,
> + struct intel_encoder *encoder,
> + const struct intel_crtc_state *crtc_state,
> + const struct drm_connector_state *conn_state)
> +{
> + struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
> + struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
> + enum phy phy = intel_port_to_phy(dev_priv, encoder->port);
> + struct intel_digital_port *dig_port = enc_to_dig_port(encoder);
> + bool is_mst = intel_crtc_has_type(crtc_state, INTEL_OUTPUT_DP_MST);
> + int level = intel_ddi_dp_level(intel_dp);
> +
> + intel_dp_set_link_params(intel_dp, crtc_state->port_clock,
> + crtc_state->lane_count);
> +
> + /*
> + * 1. Enable Power Wells
> + *
> + * This was handled at the beginning of intel_atomic_commit_tail(),
> + * before we called down into this function.
> + */
> +
> + /* 2. Enable Panel Power if PPS is required */
> + intel_pps_on(intel_dp);
> +
> + /*
> + * 3. Enable the port PLL.
> + */
> + intel_ddi_enable_clock(encoder, crtc_state);
> +
> + /* 4. Enable IO power */
> + if (!intel_phy_is_tc(dev_priv, phy) ||
> + dig_port->tc_mode != TC_PORT_TBT_ALT)
> + dig_port->ddi_io_wakeref = intel_display_power_get(dev_priv,
> + dig_port->ddi_io_power_domain);
> +
> + /*
> + * 5. The rest of the below are substeps under the bspec's "Enable and
> + * Train Display Port" step. Note that steps that are specific to
> + * MST will be handled by intel_mst_pre_enable_dp() before/after it
> + * calls into this function. Also intel_mst_pre_enable_dp() only calls
> + * us when active_mst_links==0, so any steps designated for "single
> + * stream or multi-stream master transcoder" can just be performed
> + * unconditionally here.
> + */
> +
> + /*
> + * 5.a Configure Transcoder Clock Select to direct the Port clock to the
> + * Transcoder.
> + */
> + intel_ddi_enable_pipe_clock(encoder, crtc_state);
> +
> + /* 5.b Not relevant to i915 for now */
> +
> + /*
> + * 5.c Configure TRANS_DDI_FUNC_CTL DDI Select, DDI Mode Select & MST
> + * Transport Select
> + */
> + intel_ddi_config_transcoder_func(encoder, crtc_state);
> +
> + /*
> + * 5.d Configure & enable DP_TP_CTL with link training pattern 1
> + * selected
> + *
> + * This will be handled by the intel_dp_start_link_train() farther
> + * down this function.
> + */
> +
> + /* 5.e Configure voltage swing and related IO settings */
> + intel_snps_phy_ddi_vswing_sequence(encoder, level);
> +
> + /*
> + * 5.f Configure and enable DDI_BUF_CTL
> + * 5.g Wait for DDI_BUF_CTL DDI Idle Status = 0b (Not Idle), timeout
> + * after 1200 us.
> + *
> + * We only configure what the register value will be here. Actual
> + * enabling happens during link training farther down.
> + */
> + intel_ddi_init_dp_buf_reg(encoder, crtc_state);
> +
> + if (!is_mst)
> + intel_dp_set_power(intel_dp, DP_SET_POWER_D0);
> +
> + intel_dp_sink_set_decompression_state(intel_dp, crtc_state, true);
> + /*
> + * DDI FEC: "anticipates enabling FEC encoding sets the FEC_READY bit
> + * in the FEC_CONFIGURATION register to 1 before initiating link
> + * training
> + */
> + intel_dp_sink_set_fec_ready(intel_dp, crtc_state);
> +
> + /*
> + * 5.h Follow DisplayPort specification training sequence (see notes for
> + * failure handling)
> + * 5.i If DisplayPort multi-stream - Set DP_TP_CTL link training to Idle
> + * Pattern, wait for 5 idle patterns (DP_TP_STATUS Min_Idles_Sent)
> + * (timeout after 800 us)
> + */
> + intel_dp_start_link_train(intel_dp, crtc_state);
> +
> + /* 5.j Set DP_TP_CTL link training to Normal */
> + if (!is_trans_port_sync_mode(crtc_state))
> + intel_dp_stop_link_train(intel_dp, crtc_state);
> +
> + /* 5.k Configure and enable FEC if needed */
> + intel_ddi_enable_fec(encoder, crtc_state);
> + intel_dsc_enable(encoder, crtc_state);
> +}
> +
> static void tgl_ddi_pre_enable_dp(struct intel_atomic_state *state,
> struct intel_encoder *encoder,
> const struct intel_crtc_state *crtc_state,
> @@ -2573,10 +2691,7 @@ static void tgl_ddi_pre_enable_dp(struct intel_atomic_state *state,
> */
>
> /* 7.e Configure voltage swing and related IO settings */
> - if (IS_DG2(dev_priv))
> - intel_snps_phy_ddi_vswing_sequence(encoder, level);
> - else
> - tgl_ddi_vswing_sequence(encoder, crtc_state, level);
> + tgl_ddi_vswing_sequence(encoder, crtc_state, level);
>
> /*
> * 7.f Combo PHY: Configure PORT_CL_DW10 Static Power Down to power up
> @@ -2708,7 +2823,9 @@ static void intel_ddi_pre_enable_dp(struct intel_atomic_state *state,
> {
> struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
>
> - if (DISPLAY_VER(dev_priv) >= 12)
> + if (IS_DG2(dev_priv))
> + dg2_ddi_pre_enable_dp(state, encoder, crtc_state, conn_state);
> + else if (DISPLAY_VER(dev_priv) >= 12)
> tgl_ddi_pre_enable_dp(state, encoder, crtc_state, conn_state);
> else
> hsw_ddi_pre_enable_dp(state, encoder, crtc_state, conn_state);
> @@ -4634,6 +4751,8 @@ void intel_ddi_init(struct drm_i915_private *dev_priv, enum port port)
> encoder->pipe_mask = ~0;
>
> if (IS_DG2(dev_priv)) {
> + encoder->enable_clock = intel_mpllb_enable;
> + encoder->disable_clock = intel_mpllb_disable;
> encoder->get_config = dg2_ddi_get_config;
> } else if (IS_ALDERLAKE_S(dev_priv)) {
> encoder->enable_clock = adls_ddi_enable_clock;
--
Jani Nikula, Intel Open Source Graphics Center
More information about the dri-devel
mailing list