[PATCH v5 5/6] backlight: rt4831: Adds support for Richtek RT4831 backlight
Daniel Thompson
daniel.thompson at linaro.org
Thu Mar 25 11:53:06 UTC 2021
On Thu, Dec 17, 2020 at 11:00:43PM +0800, cy_huang wrote:
> From: ChiYuan Huang <cy_huang at richtek.com>
>
> Adds support for Richtek RT4831 backlight.
>
> Signed-off-by: ChiYuan Huang <cy_huang at richtek.com>
Looks ok but there are a few minor niggles.
> ---
> drivers/video/backlight/Kconfig | 8 ++
> drivers/video/backlight/Makefile | 1 +
> drivers/video/backlight/rt4831-backlight.c | 219 +++++++++++++++++++++++++++++
> 3 files changed, 228 insertions(+)
> create mode 100644 drivers/video/backlight/rt4831-backlight.c
>
> diff --git a/drivers/video/backlight/Kconfig b/drivers/video/backlight/Kconfig
> index d83c87b..666bdb0 100644
> --- a/drivers/video/backlight/Kconfig
> +++ b/drivers/video/backlight/Kconfig
> @@ -289,6 +289,14 @@ config BACKLIGHT_QCOM_WLED
> If you have the Qualcomm PMIC, say Y to enable a driver for the
> WLED block. Currently it supports PM8941 and PMI8998.
>
> +config BACKLIGHT_RT4831
> + tristate "Richtek RT4831 Backlight Driver"
> + depends on MFD_RT4831
> + help
> + This enables support for Richtek RT4831 Backlight driver.
> + It's commont used to drive the display WLED. There're four channels
^^^
> diff --git a/drivers/video/backlight/rt4831-backlight.c b/drivers/video/backlight/rt4831-backlight.c
> new file mode 100644
> index 00000000..816c4d6
> --- /dev/null
> +++ b/drivers/video/backlight/rt4831-backlight.c
> @@ -0,0 +1,219 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +
> +#include <dt-bindings/leds/rt4831-backlight.h>
> +#include <linux/backlight.h>
> +#include <linux/bitops.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/mutex.h>
> +#include <linux/platform_device.h>
> +#include <linux/property.h>
> +#include <linux/regmap.h>
> +
> +#define RT4831_REG_BLCFG 0x02
> +#define RT4831_REG_BLDIML 0x04
> +#define RT4831_REG_ENABLE 0x08
> +
> +#define BL_MAX_BRIGHTNESS 2048
Would be better with a prefix.
> +
> +#define RT4831_BLOVP_MASK GENMASK(7, 5)
> +#define RT4831_BLOVP_SHIFT 5
> +#define RT4831_BLPWMEN_MASK BIT(0)
> +#define RT4831_BLEN_MASK BIT(4)
> +#define RT4831_BLCH_MASK GENMASK(3, 0)
> +#define RT4831_BLDIML_MASK GENMASK(2, 0)
> +#define RT4831_BLDIMH_MASK GENMASK(10, 3)
> +#define RT4831_BLDIMH_SHIFT 3
> +
> +struct rt4831_priv {
> + struct regmap *regmap;
> + struct mutex lock;
Locks aren't very common in backlight drivers. Why isn't the ops_lock
sufficient?
> + struct backlight_device *bl;
> +};
> +
> +static int rt4831_bl_update_status(struct backlight_device *bl_dev)
> +{
> + struct rt4831_priv *priv = bl_get_data(bl_dev);
> + int brightness = backlight_get_brightness(bl_dev);
> + unsigned int enable = brightness ? RT4831_BLEN_MASK : 0;
> + u8 v[2];
> + int ret;
> +
> + mutex_lock(&priv->lock);
> +
> + if (brightness) {
> + v[0] = (brightness - 1) & RT4831_BLDIML_MASK;
> + v[1] = ((brightness - 1) & RT4831_BLDIMH_MASK) >> RT4831_BLDIMH_SHIFT;
> +
> + ret = regmap_raw_write(priv->regmap, RT4831_REG_BLDIML, v, sizeof(v));
> + if (ret)
> + goto unlock;
> + }
> +
> + ret = regmap_update_bits(priv->regmap, RT4831_REG_ENABLE, RT4831_BLEN_MASK, enable);
> +
> +unlock:
> + mutex_unlock(&priv->lock);
> + return ret;
> +}
> +
> +static int rt4831_bl_get_brightness(struct backlight_device *bl_dev)
> +{
> + struct rt4831_priv *priv = bl_get_data(bl_dev);
> + unsigned int val;
> + u8 v[2];
> + int ret;
> +
> + mutex_lock(&priv->lock);
> +
> + ret = regmap_read(priv->regmap, RT4831_REG_ENABLE, &val);
> + if (ret)
> + return ret;
Deadlock.
> +
> + if (!(val & RT4831_BLEN_MASK)) {
> + ret = 0;
> + goto unlock;
> + }
> +
> + ret = regmap_raw_read(priv->regmap, RT4831_REG_BLDIML, v, sizeof(v));
> + if (ret)
> + goto unlock;
> +
> + ret = (v[1] << RT4831_BLDIMH_SHIFT) + (v[0] & RT4831_BLDIML_MASK) + 1;
> +
> +unlock:
> + mutex_unlock(&priv->lock);
> + return ret;
> +}
> +
> +static const struct backlight_ops rt4831_bl_ops = {
> + .options = BL_CORE_SUSPENDRESUME,
> + .update_status = rt4831_bl_update_status,
> + .get_brightness = rt4831_bl_get_brightness,
> +};
> +
> +static int rt4831_init_device_properties(struct rt4831_priv *priv, struct device *dev,
This is not the idiomatic name usually used for this type of function.
In fact since this driver purely uses device properties then this code
could just be merged into the probe function.
> + struct backlight_properties *bl_props)
> +{
> + u8 propval;
> + u32 brightness;
> + unsigned int val = 0;
> + int ret;
> +
> + /* common properties */
> + ret = device_property_read_u32(dev, "max-brightness", &brightness);
> + if (ret) {
> + dev_warn(dev, "max-brightness DT property missing, use HW max as default\n");
Does there need to be a warning on this?
It's code pattern is common but the DT docs have formalized a lot
recently. The DT docs in patch 1 say these are optional... so
why does it justify a warning of they are omitted? There is nothing
wrong! Is it better to specify the defaults in the bindings and
then the kernel can say nothing when the defaults are adopted.
> + brightness = BL_MAX_BRIGHTNESS;
> + }
> +
> + bl_props->max_brightness = min_t(u32, brightness, BL_MAX_BRIGHTNESS);
> +
> + ret = device_property_read_u32(dev, "default-brightness", &brightness);
> + if (ret) {
> + dev_warn(dev, "default-brightness DT property missing, use max limit as default\n");
Ditto.
> + brightness = bl_props->max_brightness;
> + }
> +
> + bl_props->brightness = min_t(u32, brightness, bl_props->max_brightness);
> +
> + /* vendor properties */
> + if (device_property_read_bool(dev, "richtek,pwm-enable"))
> + val = RT4831_BLPWMEN_MASK;
> +
> + ret = regmap_update_bits(priv->regmap, RT4831_REG_BLCFG, RT4831_BLPWMEN_MASK, val);
> + if (ret)
> + return ret;
> +
> + ret = device_property_read_u8(dev, "richtek,bled-ovp-sel", &propval);
> + if (ret) {
> + dev_warn(dev, "richtek,bled-ovp-sel DT property missing,
> use default 21V\n");o
Ditto.
> + propval = RT4831_BLOVPLVL_21V;
> + }
> +
> + propval = min_t(u8, propval, RT4831_BLOVPLVL_29V);
> + ret = regmap_update_bits(priv->regmap, RT4831_REG_BLCFG, RT4831_BLOVP_MASK,
> + propval << RT4831_BLOVP_SHIFT);
> + if (ret)
> + return ret;
> +
> + ret = device_property_read_u8(dev, "richtek,channel-use", &propval);
> + if (ret) {
> + dev_err(dev, "richtek,channel-use DT property missing\n");
> + return ret;
> + }
> +
> + if (!(propval & RT4831_BLCH_MASK)) {
> + dev_err(dev, "No channel specified\n");
> + return -EINVAL;
> + }
> +
> + return regmap_update_bits(priv->regmap, RT4831_REG_ENABLE, RT4831_BLCH_MASK, propval);
> +}
> +
> +static int rt4831_bl_probe(struct platform_device *pdev)
> +{
> + struct rt4831_priv *priv;
> + struct backlight_properties bl_props = { .type = BACKLIGHT_RAW, };
In new drivers please make sure to correctly set props.scale so that the
backlight slider can be mapped correctly (see
Documentation/ABI/testing/sysfs-class-backlight for description of the
options).
Daniel.
More information about the dri-devel
mailing list