[PATCH v10, 00/19] Support multi hardware decode using of_platform_populate

yunfei.dong at mediatek.com yunfei.dong at mediatek.com
Tue Nov 16 11:42:44 UTC 2021


Hi Ezequiel,

Thanks for you suggestion.
On Sun, 2021-11-14 at 19:04 -0300, Ezequiel Garcia wrote:
> Hi Yunfei,
> 
> On Thu, 11 Nov 2021 at 01:15, Yunfei Dong <yunfei.dong at mediatek.com>
> wrote:
> > 
> > This series adds support for multi hardware decode into mtk-vcodec, 
> > by first adding use
> > of_platform_populate to manage each hardware information:
> > interrupt, clock, register
> > bases and power. Secondly add core work queue to deal with core
> > hardware message,
> > at the same time, add msg queue for different hardware share
> > messages. Lastly, the
> > architecture of different specs are not the same, using specs type
> > to separate them.
> > 
> > This series has been tested with both MT8183 and MT8173. Decoding
> > was working for both chips.
> > 
> 
> How are you testing Decoding? If you are running some test suite, it
> would
> be good to add such information.
> 
For 8183 and 8173, these patches don't have influence for them, can
work well.

These patches are used for mt8192 and 8195. We do cts/gts/stress test
to check our drivers.
> Are you testing some edge-cases such as parallel/concurrent decoding,
> removing the driver while streaming, and so on? This should help
> catch
> some typical issues.
> 
> Thanks,
> Ezequiel
> 
Thanks,
Yunfei Dong
> > Patches 1~3 rewrite get register bases and power on/off interface.
> > Patches 4 export decoder pm interfaces.
> > Patches 5 add to support 8192.
> > Patch 6 support multi hardware.
> > Patch 7 separate video encoder and decoder document
> > Patch 8-17 add interfaces to support core hardware.
> > Patch 18-19 remove mtk_vcodec_release_dec/enc_pm interfaces.
> > ---
> > changes compared with v9:
> > - need not to build ko, just export pm interfaces for patch 04/19.
> > - fix comments for patch 06/19
> > 
> > changes compared with v8:
> > - add new patch 18~19 to remove mtk_vcodec_release_de/enc_pm
> > interfaces.
> > - fix spelling mistakes for patch 17/19
> > - fix yaml comments for patch 15/19
> > 
> > Changes compared with v7:
> > - add new patch 4 to build decoder pm file as module
> > - add new patch 5 to support 8192
> > - fix comments for patch 6/17
> > - change some logic for using work queue instead of create thread
> > for core hardware decode for patch 10/17
> > - using work queue for hardware decode instead of create thread for
> > patch 13/17
> > - add returen value for patch 14/17
> > - fix yaml check fail 15/17
> > 
> > Changes compared with v6:
> > - Use of_platform_populate to manage multi hardware, not component
> > framework for patch 4/15
> > - Re-write dtsi document for hardware architecture changed for
> > patch 13/15 -The dtsi will write like below in patch 13/15:
> >     vcodec_dec: vcodec_dec at 16000000 {
> >         compatible = "mediatek,mt8192-vcodec-dec";
> >         #address-cells = <2>;
> >         #size-cells = <2>;
> >         ranges;
> >         reg = <0 0x16000000 0 0x1000>;          /* VDEC_SYS */
> >         mediatek,scp = <&scp>;
> >         iommus = <&iommu0 M4U_PORT_L4_VDEC_MC_EXT>;
> >         dma-ranges = <0x1 0x0 0x0 0x40000000 0x0 0xfff00000>;
> >         vcodec_lat {
> >             compatible = "mediatek,mtk-vcodec-lat";
> >             reg = <0 0x16010000 0 0x800>;               /*
> > VDEC_MISC */
> >             reg-name = "reg-misc";
> >             interrupts = <GIC_SPI 426 IRQ_TYPE_LEVEL_HIGH 0>;
> >             iommus = <&iommu0 M4U_PORT_L5_VDEC_LAT0_VLD_EXT>,
> >                  <&iommu0 M4U_PORT_L5_VDEC_LAT0_VLD2_EXT>,
> >                  <&iommu0 M4U_PORT_L5_VDEC_LAT0_AVC_MV_EXT>,
> >                  <&iommu0 M4U_PORT_L5_VDEC_LAT0_PRED_RD_EXT>,
> >                  <&iommu0 M4U_PORT_L5_VDEC_LAT0_TILE_EXT>,
> >                  <&iommu0 M4U_PORT_L5_VDEC_LAT0_WDMA_EXT>,
> >                  <&iommu0 M4U_PORT_L5_VDEC_LAT0_RG_CTRL_DMA_EXT>,
> >                  <&iommu0 M4U_PORT_L5_VDEC_UFO_ENC_EXT>;
> >             clocks = <&topckgen CLK_TOP_VDEC_SEL>,
> >                  <&vdecsys_soc CLK_VDEC_SOC_VDEC>,
> >                  <&vdecsys_soc CLK_VDEC_SOC_LAT>,
> >                  <&vdecsys_soc CLK_VDEC_SOC_LARB1>,
> >                  <&topckgen CLK_TOP_MAINPLL_D4>;
> >             clock-names = "vdec-sel", "vdec-soc-vdec", "vdec-soc-
> > lat",
> >                   "vdec-vdec", "vdec-top";
> >             assigned-clocks = <&topckgen CLK_TOP_VDEC_SEL>;
> >             assigned-clock-parents = <&topckgen
> > CLK_TOP_MAINPLL_D4>;
> >             power-domains = <&spm MT8192_POWER_DOMAIN_VDEC>;
> >         };
> > 
> >         vcodec_core {
> >             compatible = "mediatek,mtk-vcodec-core";
> >             reg = <0 0x16025000 0 0x1000>;              /*
> > VDEC_CORE_MISC */
> >             reg-names = "reg-misc";
> >             interrupts = <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH 0>;
> >             iommus = <&iommu0 M4U_PORT_L4_VDEC_MC_EXT>,
> >                  <&iommu0 M4U_PORT_L4_VDEC_UFO_EXT>,
> >                  <&iommu0 M4U_PORT_L4_VDEC_PP_EXT>,
> >                  <&iommu0 M4U_PORT_L4_VDEC_PRED_RD_EXT>,
> >                  <&iommu0 M4U_PORT_L4_VDEC_PRED_WR_EXT>,
> >                  <&iommu0 M4U_PORT_L4_VDEC_PPWRAP_EXT>,
> >                  <&iommu0 M4U_PORT_L4_VDEC_TILE_EXT>,
> >                  <&iommu0 M4U_PORT_L4_VDEC_VLD_EXT>,
> >                  <&iommu0 M4U_PORT_L4_VDEC_VLD2_EXT>,
> >                  <&iommu0 M4U_PORT_L4_VDEC_AVC_MV_EXT>,
> >                  <&iommu0 M4U_PORT_L4_VDEC_RG_CTRL_DMA_EXT>;
> >             clocks = <&topckgen CLK_TOP_VDEC_SEL>,
> >                  <&vdecsys CLK_VDEC_VDEC>,
> >                  <&vdecsys CLK_VDEC_LAT>,
> >                  <&vdecsys CLK_VDEC_LARB1>,
> >                  <&topckgen CLK_TOP_MAINPLL_D4>;
> >             clock-names = "vdec-sel", "vdec-soc-vdec", "vdec-soc-
> > lat",
> >                   "vdec-vdec", "vdec-top";
> >             assigned-clocks = <&topckgen CLK_TOP_VDEC_SEL>;
> >             assigned-clock-parents = <&topckgen
> > CLK_TOP_MAINPLL_D4>;
> >             power-domains = <&spm MT8192_POWER_DOMAIN_VDEC2>;
> >         };
> >     };
> > 
> > Changes compared with v5:
> > - Add decoder hardware block diagram for patch 13/15
> > 
> > Changes compared with v4:
> > - Fix comments for patch 4/15
> >   >> +     if (dev->is_comp_supported) {
> >   >> +             ret = mtk_vcodec_init_master(dev);
> >   >> +             if (ret < 0)
> >   >> +                     goto err_component_match;
> >   >> +     } else {
> >   >> +             platform_set_drvdata(pdev, dev);
> >   >> +     }
> >   Fix platform_set_drvdata.
> > - Fix build error for patch 9/15
> > - Add depend patch in case of error header file for patch 13/15
> > 
> > Changes compared with v3:
> > - Fix return value for patch 1/15
> > - Fix comments for patch 4/15
> >   > Looking up "mediatek,mtk-vcodec-core" to determine if it uses
> > component framwork sounds like...
> >   Add prameter in pdata, for all platform will use compoent after
> > mt8183
> > 
> >   >> +     if (dev->is_comp_supported) {
> >   >> +             ret = mtk_vcodec_init_master(dev);
> >   >> +             if (ret < 0)
> >   >> +                     goto err_component_match;
> >   >> +     } else {
> >   >> +             platform_set_drvdata(pdev, dev);
> >   >> +     }
> >   > + Has asked the same question in [1].  Why it removes the
> >   > +platform_set_drvdata() above?  mtk_vcodec_init_master() also
> > calls platform_set_drvdata().
> >   Must call component_master_add_with_match after
> > platform_set_drvdata for component architecture.
> > - Fix yaml files check fail for patch 5/15
> > - Fix yaml file check fail for patch 14/15
> > 
> > Changes compared with v1:
> > - Fix many comments for patch 3/14
> > - Remove unnecessary code for patch 4/14
> > - Using enum mtk_vdec_hw_count instead of magic numbers for patch
> > 6/14
> > - Reconstructed get/put lat buffer for lat and core hardware for
> > patch 7/14
> > - Using yaml format to instead of txt file for patch 12/14
> > 
> > Yunfei Dong (19):
> >   media: mtk-vcodec: Get numbers of register bases from DT
> >   media: mtk-vcodec: Align vcodec wake up interrupt interface
> >   media: mtk-vcodec: Refactor vcodec pm interface
> >   media: mtk-vcodec: export decoder pm functions
> >   media: mtk-vcodec: Support MT8192
> >   media: mtk-vcodec: Manage multi hardware information
> >   dt-bindings: media: mtk-vcodec: Separate video encoder and
> > decoder
> >     dt-bindings
> >   media: mtk-vcodec: Use pure single core for MT8183
> >   media: mtk-vcodec: Add irq interface for multi hardware
> >   media: mtk-vcodec: Add msg queue feature for lat and core
> > architecture
> >   media: mtk-vcodec: Generalize power and clock on/off interfaces
> >   media: mtk-vcodec: Add new interface to lock different hardware
> >   media: mtk-vcodec: Add work queue for core hardware decode
> >   media: mtk-vcodec: Support 34bits dma address for vdec
> >   dt-bindings: media: mtk-vcodec: Adds decoder dt-bindings for
> > mt8192
> >   media: mtk-vcodec: Add core dec and dec end ipi msg
> >   media: mtk-vcodec: Use codec type to separate different hardware
> >   media: mtk-vcodec: Remove mtk_vcodec_release_dec_pm
> >   media: mtk-vcodec: Remove mtk_vcodec_release_enc_pm
> > 
> >  .../media/mediatek,vcodec-decoder.yaml        | 176 +++++++++++
> >  .../media/mediatek,vcodec-encoder.yaml        | 187 ++++++++++++
> >  .../media/mediatek,vcodec-subdev-decoder.yaml | 261
> > ++++++++++++++++
> >  .../bindings/media/mediatek-vcodec.txt        | 131 --------
> >  drivers/media/platform/mtk-vcodec/Makefile    |   6 +-
> >  .../platform/mtk-vcodec/mtk_vcodec_dec.c      |   4 +-
> >  .../platform/mtk-vcodec/mtk_vcodec_dec.h      |   1 +
> >  .../platform/mtk-vcodec/mtk_vcodec_dec_drv.c  | 219 +++++++++++---
> >  .../platform/mtk-vcodec/mtk_vcodec_dec_hw.c   | 172 +++++++++++
> >  .../platform/mtk-vcodec/mtk_vcodec_dec_hw.h   |  55 ++++
> >  .../platform/mtk-vcodec/mtk_vcodec_dec_pm.c   | 104 +++++--
> >  .../platform/mtk-vcodec/mtk_vcodec_dec_pm.h   |  12 +-
> >  .../mtk-vcodec/mtk_vcodec_dec_stateful.c      |   2 +
> >  .../mtk-vcodec/mtk_vcodec_dec_stateless.c     |  20 ++
> >  .../platform/mtk-vcodec/mtk_vcodec_drv.h      |  75 ++++-
> >  .../platform/mtk-vcodec/mtk_vcodec_enc_drv.c  |  21 +-
> >  .../platform/mtk-vcodec/mtk_vcodec_enc_pm.c   |  10 +-
> >  .../platform/mtk-vcodec/mtk_vcodec_enc_pm.h   |   3 +-
> >  .../platform/mtk-vcodec/mtk_vcodec_intr.c     |  27 +-
> >  .../platform/mtk-vcodec/mtk_vcodec_intr.h     |   4 +-
> >  .../platform/mtk-vcodec/mtk_vcodec_util.c     |  87 +++++-
> >  .../platform/mtk-vcodec/mtk_vcodec_util.h     |   8 +-
> >  .../platform/mtk-vcodec/vdec/vdec_h264_if.c   |   2 +-
> >  .../mtk-vcodec/vdec/vdec_h264_req_if.c        |   2 +-
> >  .../platform/mtk-vcodec/vdec/vdec_vp8_if.c    |   2 +-
> >  .../platform/mtk-vcodec/vdec/vdec_vp9_if.c    |   2 +-
> >  .../media/platform/mtk-vcodec/vdec_drv_if.c   |  21 +-
> >  .../media/platform/mtk-vcodec/vdec_ipi_msg.h  |  16 +-
> >  .../platform/mtk-vcodec/vdec_msg_queue.c      | 286
> > ++++++++++++++++++
> >  .../platform/mtk-vcodec/vdec_msg_queue.h      | 148 +++++++++
> >  .../media/platform/mtk-vcodec/vdec_vpu_if.c   |  46 ++-
> >  .../media/platform/mtk-vcodec/vdec_vpu_if.h   |  22 ++
> >  .../platform/mtk-vcodec/venc/venc_h264_if.c   |   2 +-
> >  .../platform/mtk-vcodec/venc/venc_vp8_if.c    |   2 +-
> >  34 files changed, 1841 insertions(+), 295 deletions(-)
> >  create mode 100644
> > Documentation/devicetree/bindings/media/mediatek,vcodec-
> > decoder.yaml
> >  create mode 100644
> > Documentation/devicetree/bindings/media/mediatek,vcodec-
> > encoder.yaml
> >  create mode 100644
> > Documentation/devicetree/bindings/media/mediatek,vcodec-subdev-
> > decoder.yaml
> >  delete mode 100644
> > Documentation/devicetree/bindings/media/mediatek-vcodec.txt
> >  create mode 100644 drivers/media/platform/mtk-
> > vcodec/mtk_vcodec_dec_hw.c
> >  create mode 100644 drivers/media/platform/mtk-
> > vcodec/mtk_vcodec_dec_hw.h
> >  create mode 100644 drivers/media/platform/mtk-
> > vcodec/vdec_msg_queue.c
> >  create mode 100644 drivers/media/platform/mtk-
> > vcodec/vdec_msg_queue.h
> > 
> > --
> > 2.25.1
> > 


More information about the dri-devel mailing list