[PATCH v5 3/7] drm: sun4i: dsi: Convert to bridge driver

[Jagan Teki]

On Thu, Nov 25, 2021 at 9:40 PM Maxime Ripard <maxime at cerno.tech> wrote:
>
> On Thu, Nov 25, 2021 at 07:55:41PM +0530, Jagan Teki wrote:
> > Hi,
> >
> > On Thu, Nov 25, 2021 at 7:45 PM Maxime Ripard <maxime at cerno.tech> wrote:
> > >
> > > On Wed, Nov 24, 2021 at 12:02:47AM +0530, Jagan Teki wrote:
> > > > > > > > > +     dsi->panel = of_drm_find_panel(remote);
> > > > > > > > > +     if (IS_ERR(dsi->panel)) {
> > > > > > > > > +             dsi->panel = NULL;
> > > > > > > > > +
> > > > > > > > > +             dsi->next_bridge = of_drm_find_bridge(remote);
> > > > > > > > > +             if (IS_ERR(dsi->next_bridge)) {
> > > > > > > > > +                     dev_err(dsi->dev, "failed to find bridge\n");
> > > > > > > > > +                     return PTR_ERR(dsi->next_bridge);
> > > > > > > > > +             }
> > > > > > > > > +     } else {
> > > > > > > > > +             dsi->next_bridge = NULL;
> > > > > > > > > +     }
> > > > > > > > > +
> > > > > > > > > +     of_node_put(remote);
> > > > > > > >
> > > > > > > > Using devm_drm_of_get_bridge would greatly simplify the driver
> > > > > > >
> > > > > > > I'm aware of this and this would break the existing sunxi dsi binding,
> > > > > > > we are not using ports based pipeline in dsi node. Of-course you have
> > > > > > > pointed the same before, please check below
> > > > > > > https://patchwork.kernel.org/project/dri-devel/patch/20210322140152.101709-2-jagan@amarulasolutions.com/
> > > > > >
> > > > > > Then drm_of_find_panel_or_bridge needs to be adjusted to handle the DSI
> > > > > > bindings and look for a panel or bridge not only through the OF graph,
> > > > > > but also on the child nodes
> > > > >
> > > > > Okay. I need to check this.
> > > >
> > > > devm_drm_of_get_bridge is not working with legacy binding like the one
> > > > used in sun6i dsi
> > >
> > > There's nothing legacy about it.
> >
> > What I'm mean legacy here with current binding used in sun6i-dsi like this.
> >
> > &dsi {
> >           vcc-dsi-supply = <&reg_dcdc1>; /* VCC-DSI */
> >           status = "okay";
> >
> >          panel at 0 {
> >                    compatible = "bananapi,s070wv20-ct16-icn6211";
> >                    reg = <0>;
> >                    reset-gpios = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /*
> > LCD-RST: PL5 */
> >                   enable-gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>; /*
> > LCD-PWR-EN: PB7 */
> >                   backlight = <&backlight>;
> >         };
> > };
>
> Yes, I know, it's the generic DSI binding. It's still not legacy.
>
> > devm_drm_of_get_bridge cannot find the device with above binding and
> > able to find the device with below binding.
> >
> > &dsi {
> >        vcc-dsi-supply = <&reg_dcdc1>; /* VCC-DSI */
> >        status = "okay";
> >
> >       ports {
> >             #address-cells = <1>;
> >             #size-cells = <0>;
> >
> >            dsi_out: port at 0 {
> >                    reg = <0>;
> >
> >                   dsi_out_bridge: endpoint {
> >                             remote-endpoint = <&bridge_out_dsi>;
> >                   };
> >            };
> >       };
> >
> >       panel at 0 {
> >              compatible = "bananapi,s070wv20-ct16-icn6211";
> >              reg = <0>;
> >              reset-gpios = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* LCD-RST: PL5 */
> >              enable-gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>; /* LCD-PWR-EN: PB7 */
> >              backlight = <&backlight>;
> >
> >               port {
> >                         bridge_out_dsi: endpoint {
> >                                 remote-endpoint = <&dsi_out_bridge>;
> >                         };
> >                 };
> >        };
> > };
>
> Yes, I know, and that's because ...

Okay. I will use find panel and bridge separately instead of
devm_drm_of_get_bridge in version patches.

>
> > >
> > > > https://patchwork.kernel.org/project/dri-devel/patch/20211122065223.88059-6-jagan@amarulasolutions.com/
> > > >
> > > > dsi->next_bridge = devm_drm_of_get_bridge(dsi->dev, dsi->dev->of_node, 0, 0);
> > > > if (IS_ERR(dsi->next_bridge))
> > > >            return PTR_ERR(dsi->next_bridge);
> > > >
> > > > It is only working if we have ports on the pipeline, something like this
> > > > https://patchwork.kernel.org/project/dri-devel/patch/20210214194102.126146-8-jagan@amarulasolutions.com/
> > > >
> > > > Please have a look and let me know if I miss anything?
> > >
> > > Yes, you're missing the answer you quoted earlier:
> >
> > Yes, I'm trying to resolve the comment one after another. Will get back.
>
> ... You've ignored that comment.

Not understand which comment you mean. There are few about bridge
conversion details, I will send my comments.

Thanks,
Jagan.