[PATCH 2/4] drm/bridge: tc358767: Move hardware init to enable callback

[Marek Vasut]

The TC358767/TC358867/TC9595 are all capable of operating either from
attached Xtal or from DSI clock lane clock. In case the later is used,
all I2C accesses will fail until the DSI clock lane is running and
supplying clock to the chip.

Move all hardware initialization to enable callback to guarantee the
DSI clock lane is running before accessing the hardware. In case Xtal
is attached to the chip, this change has no effect.

Signed-off-by: Marek Vasut <marex at denx.de>
Cc: Andrzej Hajda <a.hajda at samsung.com>
Cc: Jernej Skrabec <jernej.skrabec at siol.net>
Cc: Jonas Karlman <jonas at kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart at ideasonboard.com>
Cc: Neil Armstrong <narmstrong at baylibre.com>
Cc: Sam Ravnborg <sam at ravnborg.org>
---
 drivers/gpu/drm/bridge/tc358767.c | 111 +++++++++++++++++-------------
 1 file changed, 63 insertions(+), 48 deletions(-)

diff --git a/drivers/gpu/drm/bridge/tc358767.c b/drivers/gpu/drm/bridge/tc358767.c
index 23a6f90b694b..f7fbf6f673e9 100644
--- a/drivers/gpu/drm/bridge/tc358767.c
+++ b/drivers/gpu/drm/bridge/tc358767.c
@@ -1234,11 +1234,74 @@ static int tc_stream_disable(struct tc_data *tc)
 	return 0;
 }
 
+static int tc_hardware_init(struct tc_data *tc)
+{
+	int ret;
+
+	ret = regmap_read(tc->regmap, TC_IDREG, &tc->rev);
+	if (ret) {
+		dev_err(tc->dev, "can not read device ID: %d\n", ret);
+		return ret;
+	}
+
+	if ((tc->rev != 0x6601) && (tc->rev != 0x6603)) {
+		dev_err(tc->dev, "invalid device ID: 0x%08x\n", tc->rev);
+		return -EINVAL;
+	}
+
+	tc->assr = (tc->rev == 0x6601); /* Enable ASSR for eDP panels */
+
+	if (!tc->reset_gpio) {
+		/*
+		 * If the reset pin isn't present, do a software reset. It isn't
+		 * as thorough as the hardware reset, as we can't reset the I2C
+		 * communication block for obvious reasons, but it's getting the
+		 * chip into a defined state.
+		 */
+		regmap_update_bits(tc->regmap, SYSRSTENB,
+				ENBLCD0 | ENBBM | ENBDSIRX | ENBREG | ENBHDCP,
+				0);
+		regmap_update_bits(tc->regmap, SYSRSTENB,
+				ENBLCD0 | ENBBM | ENBDSIRX | ENBREG | ENBHDCP,
+				ENBLCD0 | ENBBM | ENBDSIRX | ENBREG | ENBHDCP);
+		usleep_range(5000, 10000);
+	}
+
+	if (tc->hpd_pin >= 0) {
+		u32 lcnt_reg = tc->hpd_pin == 0 ? INT_GP0_LCNT : INT_GP1_LCNT;
+		u32 h_lc = INT_GPIO_H(tc->hpd_pin) | INT_GPIO_LC(tc->hpd_pin);
+
+		/* Set LCNT to 2ms */
+		regmap_write(tc->regmap, lcnt_reg,
+			     clk_get_rate(tc->refclk) * 2 / 1000);
+		/* We need the "alternate" mode for HPD */
+		regmap_write(tc->regmap, GPIOM, BIT(tc->hpd_pin));
+
+		if (tc->have_irq) {
+			/* enable H & LC */
+			regmap_update_bits(tc->regmap, INTCTL_G, h_lc, h_lc);
+		}
+	}
+
+	if (tc->have_irq) {
+		/* enable SysErr */
+		regmap_write(tc->regmap, INTCTL_G, INT_SYSERR);
+	}
+
+	return 0;
+}
+
 static void tc_bridge_enable(struct drm_bridge *bridge)
 {
 	struct tc_data *tc = bridge_to_tc(bridge);
 	int ret;
 
+	ret = tc_hardware_init(tc);
+	if (ret < 0) {
+		dev_err(tc->dev, "failed to initialize bridge: %d\n", ret);
+		return;
+	}
+
 	ret = tc_get_display_props(tc);
 	if (ret < 0) {
 		dev_err(tc->dev, "failed to read display props: %d\n", ret);
@@ -1626,9 +1689,6 @@ static int tc_probe(struct i2c_client *client, const struct i2c_device_id *id)
 	}
 
 	if (client->irq > 0) {
-		/* enable SysErr */
-		regmap_write(tc->regmap, INTCTL_G, INT_SYSERR);
-
 		ret = devm_request_threaded_irq(dev, client->irq,
 						NULL, tc_irq_handler,
 						IRQF_ONESHOT,
@@ -1641,51 +1701,6 @@ static int tc_probe(struct i2c_client *client, const struct i2c_device_id *id)
 		tc->have_irq = true;
 	}
 
-	ret = regmap_read(tc->regmap, TC_IDREG, &tc->rev);
-	if (ret) {
-		dev_err(tc->dev, "can not read device ID: %d\n", ret);
-		return ret;
-	}
-
-	if ((tc->rev != 0x6601) && (tc->rev != 0x6603)) {
-		dev_err(tc->dev, "invalid device ID: 0x%08x\n", tc->rev);
-		return -EINVAL;
-	}
-
-	tc->assr = (tc->rev == 0x6601); /* Enable ASSR for eDP panels */
-
-	if (!tc->reset_gpio) {
-		/*
-		 * If the reset pin isn't present, do a software reset. It isn't
-		 * as thorough as the hardware reset, as we can't reset the I2C
-		 * communication block for obvious reasons, but it's getting the
-		 * chip into a defined state.
-		 */
-		regmap_update_bits(tc->regmap, SYSRSTENB,
-				ENBLCD0 | ENBBM | ENBDSIRX | ENBREG | ENBHDCP,
-				0);
-		regmap_update_bits(tc->regmap, SYSRSTENB,
-				ENBLCD0 | ENBBM | ENBDSIRX | ENBREG | ENBHDCP,
-				ENBLCD0 | ENBBM | ENBDSIRX | ENBREG | ENBHDCP);
-		usleep_range(5000, 10000);
-	}
-
-	if (tc->hpd_pin >= 0) {
-		u32 lcnt_reg = tc->hpd_pin == 0 ? INT_GP0_LCNT : INT_GP1_LCNT;
-		u32 h_lc = INT_GPIO_H(tc->hpd_pin) | INT_GPIO_LC(tc->hpd_pin);
-
-		/* Set LCNT to 2ms */
-		regmap_write(tc->regmap, lcnt_reg,
-			     clk_get_rate(tc->refclk) * 2 / 1000);
-		/* We need the "alternate" mode for HPD */
-		regmap_write(tc->regmap, GPIOM, BIT(tc->hpd_pin));
-
-		if (tc->have_irq) {
-			/* enable H & LC */
-			regmap_update_bits(tc->regmap, INTCTL_G, h_lc, h_lc);
-		}
-	}
-
 	ret = tc_aux_link_setup(tc);
 	if (ret)
 		return ret;
-- 
2.33.0