[PATCH] drm/i915: Add NO_VLV_DISP_PW_DPIO_CMN_BC_INIT quirk

Ville Syrjälä ville.syrjala at linux.intel.com
Thu Oct 28 13:08:16 UTC 2021


On Wed, Oct 27, 2021 at 08:39:57PM +0200, Hans de Goede wrote:
> Hi,
> 
> On 10/27/21 15:38, Ville Syrjälä wrote:
> > On Sun, Oct 24, 2021 at 05:50:10PM +0200, Hans de Goede wrote:
> >> Add a NO_VLV_DISP_PW_DPIO_CMN_BC_INIT quirk to fix i915 not working on
> >> the Xiaomi Mi Pad 2 (with CHT x5-Z8500 SoC).
> >>
> >> The Xiaomi Mi Pad 2 uses quite an unusual hardware-design for a Cherry
> >> Trail tablet. It deviates from the typical reference design based tablets
> >> in many ways.
> >>
> >> The Mi Pad 2 does not have any DisplayPort or HDMI outouts. I suspect that
> >> as part of its unusual design it also has some supply rail which is only
> >> used for DisplayPort or HDMI not connected.
> > 
> > Do we have the VBT somewhere (preferable attached to a bug report)?
> > Maybe we can avoid an ugly quirk.
> 
> I agree that solving this in a way where we can avoid the quirk would be great.
> 
> I've filed an issue for this here now:
> 
> https://gitlab.freedesktop.org/drm/intel/-/issues/4385
> 
> This has a dump of /sys/kernel/debug/dri/0/i915_vbt as well as
> dmesg output from a boot with drm.debug=0x1e attached (from a boot
> with this patch, since otherwise the system hangs).
> 
> >>
> >> Force-enabling the dpio-common-bc powerwell as the i915 normal does at boot
> >> appears to cause the P-Unit to hang. When booting with a serial-usb console
> >> the following errors are logged before the system freezes:
> >>
> >>  i915 0000:00:02.0: [drm] *ERROR* timeout setting power well state 00000000 (fffff3ff)
> >>  i915 0000:00:02.0: [drm] *ERROR* Display PHY 0 is not power up
> > 
> > Hmm. I wonder if we're missing a clock or something...
> > 
> > Either of these do anything different?
> > 
> > --- a/drivers/gpu/drm/i915/display/intel_display_power.c
> > +++ b/drivers/gpu/drm/i915/display/intel_display_power.c
> > @@ -1419,6 +1419,10 @@ static void vlv_display_power_well_init(struct drm_i915_private *dev_priv)
> >  	for_each_pipe(dev_priv, pipe) {
> >  		u32 val = intel_de_read(dev_priv, DPLL(pipe));
> >  
> > +		val |= DPLL_SSC_REF_CLK_CHV;
> > 		or
> > +		val &= ~DPLL_SSC_REF_CLK_CHV;
> > 
> >  		val |= DPLL_REF_CLK_ENABLE_VLV | DPLL_VGA_MODE_DIS;
> >  		if (pipe != PIPE_A)
> >  			val |= DPLL_INTEGRATED_CRI_CLK_VLV;
> > 
> 
> The hang gets triggered from chv_dpio_cmn_power_well_enable() which does not
> call vlv_display_power_well_init() at all, it directly calls vlv_set_power_well()
> without first calling vlv_display_power_well_init() .
> 
> Note the same goes for vlv_dpio_cmn_power_well_enable(). Only the
> vlv_display_power_well_enable() / chv_pipe_power_well_enable() call
> vlv_display_power_well_init().
> 
> Note I can still give the suggested change a try if you want,
> the "display" powerwell is listed first and has DOMAIN_INIT set,
> so assuming for_each_power_domain_well() goes through the domains in
> the order they are listed, then vlv_display_power_well_init() will
> still run first. But it would seem to be wrong if enabling one domain
> depends on things setup by another domain ?

The power wells are hierarchical. Also power wells != power domains.

-- 
Ville Syrjälä
Intel


More information about the dri-devel mailing list