[PATCH 2/3] drm/msm/disp: dpu1: Add MSM8996 support
Dmitry Baryshkov
dmitry.baryshkov at linaro.org
Sat Apr 30 20:41:51 UTC 2022
On 30/04/2022 19:15, Konrad Dybcio wrote:
> Add support for MSM8996, which - fun fact - was the SoC that this driver
> (or rather SDE, its downstream origin) was meant for and first tested on.
>
> It has some hardware that differs from the modern SoCs, so not a lot of
> current structs could have been reused. It's also seemingly the only SoC
> supported by DPU that uses RGB pipes.
>
> Signed-off-by: Konrad Dybcio <konrad.dybcio at somainline.org>
> ---
> .../gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c | 268 ++++++++++++++++++
> drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c | 1 +
> drivers/gpu/drm/msm/msm_drv.c | 1 +
> 3 files changed, 270 insertions(+)
>
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
> index 3ac425c0ad82..0a217b5172bd 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
> @@ -16,6 +16,11 @@
> BIT(DPU_SSPP_CSC_10BIT) | BIT(DPU_SSPP_CDP) |\
> BIT(DPU_SSPP_TS_PREFILL) | BIT(DPU_SSPP_EXCL_RECT))
>
> +#define VIG_MSM8996_MASK \
> + (BIT(DPU_SSPP_SRC) | BIT(DPU_SSPP_QOS) |\
> + BIT(DPU_SSPP_CDP) | BIT(DPU_SSPP_TS_PREFILL) |\
> + BIT(DPU_SSPP_SCALER_QSEED3))
> +
> #define VIG_MSM8998_MASK \
> (VIG_MASK | BIT(DPU_SSPP_SCALER_QSEED3))
>
> @@ -30,6 +35,10 @@
>
> #define VIG_QCM2290_MASK (VIG_MASK | BIT(DPU_SSPP_QOS_8LVL))
>
> +#define DMA_MSM8996_MASK \
> + (BIT(DPU_SSPP_SRC) | BIT(DPU_SSPP_QOS) |\
> + BIT(DPU_SSPP_TS_PREFILL) | BIT(DPU_SSPP_CDP))
> +
> #define DMA_MSM8998_MASK \
> (BIT(DPU_SSPP_SRC) | BIT(DPU_SSPP_QOS) |\
> BIT(DPU_SSPP_TS_PREFILL) | BIT(DPU_SSPP_TS_PREFILL_REC1) |\
> @@ -57,6 +66,9 @@
> #define PINGPONG_SDM845_SPLIT_MASK \
> (PINGPONG_SDM845_MASK | BIT(DPU_PINGPONG_TE2))
>
> +#define RGB_MSM8996_MSK \
> + (VIG_MSM8996_MASK | BIT(DPU_SSPP_SCALER_RGB))
> +
> #define CTL_SC7280_MASK \
> (BIT(DPU_CTL_ACTIVE_CFG) | BIT(DPU_CTL_FETCH_ACTIVE) | BIT(DPU_CTL_VM_CFG))
>
> @@ -72,6 +84,14 @@
>
> #define INTF_SC7280_MASK INTF_SC7180_MASK | BIT(DPU_DATA_HCTL_EN)
>
> +#define IRQ_MSM8996_MASK (BIT(MDP_SSPP_TOP0_INTR) | \
> + BIT(MDP_SSPP_TOP0_INTR2) | \
> + BIT(MDP_SSPP_TOP0_HIST_INTR) | \
> + BIT(MDP_INTF0_INTR) | \
> + BIT(MDP_INTF1_INTR) | \
> + BIT(MDP_INTF2_INTR) | \
> + BIT(MDP_INTF3_INTR))
> +
What about AD4 blocks? I think there were two AD4 blocks, so we might
use IRQ_SDM845_MASK instead (Note: we need to check whether sdm845
really supported INTF4 interrupts or not).
> #define IRQ_SDM845_MASK (BIT(MDP_SSPP_TOP0_INTR) | \
> BIT(MDP_SSPP_TOP0_INTR2) | \
> BIT(MDP_SSPP_TOP0_HIST_INTR) | \
> @@ -207,6 +227,17 @@ static const uint32_t plane_formats_yuv[] = {
> * DPU sub blocks config
> *************************************************************/
> /* DPU top level caps */
> +static const struct dpu_caps msm8996_dpu_caps = {
> + .max_mixer_width = DEFAULT_DPU_OUTPUT_LINE_WIDTH,
> + .max_mixer_blendstages = 0x7,
> + .qseed_type = DPU_SSPP_SCALER_QSEED3,
> + .has_src_split = true,
> + .max_linewidth = DEFAULT_DPU_OUTPUT_LINE_WIDTH,
> + .pixel_ram_size = DEFAULT_PIXEL_RAM_SIZE,
> + .max_hdeci_exp = MAX_HORZ_DECIMATION,
> + .max_vdeci_exp = MAX_VERT_DECIMATION,
> +};
> +
> static const struct dpu_caps msm8998_dpu_caps = {
> .max_mixer_width = DEFAULT_DPU_OUTPUT_LINE_WIDTH,
> .max_mixer_blendstages = 0x7,
> @@ -328,6 +359,35 @@ static const struct dpu_caps sc7280_dpu_caps = {
> .pixel_ram_size = DEFAULT_PIXEL_RAM_SIZE,
> };
>
> +static const struct dpu_mdp_cfg msm8996_mdp[] = {
> + {
> + .name = "top_0", .id = MDP_TOP,
> + .base = 0x0, .len = 0x454,
> + .features = 0,
> + .highest_bank_bit = 0x2,
> + .clk_ctrls[DPU_CLK_CTRL_VIG0] = {
> + .reg_off = 0x2AC, .bit_off = 0},
Please convert to the lower case.
> + .clk_ctrls[DPU_CLK_CTRL_VIG1] = {
> + .reg_off = 0x2B4, .bit_off = 0},
> + .clk_ctrls[DPU_CLK_CTRL_VIG2] = {
> + .reg_off = 0x2BC, .bit_off = 0},
> + .clk_ctrls[DPU_CLK_CTRL_VIG3] = {
> + .reg_off = 0x2C4, .bit_off = 0},
> + .clk_ctrls[DPU_CLK_CTRL_RGB0] = {
> + .reg_off = 0x2AC, .bit_off = 4},
> + .clk_ctrls[DPU_CLK_CTRL_RGB1] = {
> + .reg_off = 0x2B4, .bit_off = 4},
> + .clk_ctrls[DPU_CLK_CTRL_RGB2] = {
> + .reg_off = 0x2BC, .bit_off = 4},
> + .clk_ctrls[DPU_CLK_CTRL_RGB3] = {
> + .reg_off = 0x2C4, .bit_off = 4},
> + .clk_ctrls[DPU_CLK_CTRL_DMA0] = {
> + .reg_off = 0x2AC, .bit_off = 8},
> + .clk_ctrls[DPU_CLK_CTRL_DMA1] = {
> + .reg_off = 0x2B4, .bit_off = 8},
There were two cursor SSPPs, please add corresponding controls here
> + },
> +};
> +
> static const struct dpu_mdp_cfg msm8998_mdp[] = {
> {
> .name = "top_0", .id = MDP_TOP,
> @@ -513,6 +573,39 @@ static const struct dpu_mdp_cfg qcm2290_mdp[] = {
> /*************************************************************
> * CTL sub blocks config
> *************************************************************/
> +static const struct dpu_ctl_cfg msm8996_ctl[] = {
> + {
> + .name = "ctl_0", .id = CTL_0,
> + .base = 0x1000, .len = 0x64,
> + .features = 0,
> + .intr_start = DPU_IRQ_IDX(MDP_SSPP_TOP0_INTR2, 9),
> + },
> + {
> + .name = "ctl_1", .id = CTL_1,
> + .base = 0x1200, .len = 0x64,
> + .features = 0,
> + .intr_start = DPU_IRQ_IDX(MDP_SSPP_TOP0_INTR2, 10),
> + },
> + {
> + .name = "ctl_2", .id = CTL_2,
> + .base = 0x1400, .len = 0x64,
> + .features = 0,
> + .intr_start = DPU_IRQ_IDX(MDP_SSPP_TOP0_INTR2, 11),
> + },
> + {
> + .name = "ctl_3", .id = CTL_3,
> + .base = 0x1600, .len = 0x64,
> + .features = 0,
> + .intr_start = DPU_IRQ_IDX(MDP_SSPP_TOP0_INTR2, 12),
> + },
> + {
> + .name = "ctl_4", .id = CTL_4,
> + .base = 0x1800, .len = 0x64,
> + .features = 0,
> + .intr_start = DPU_IRQ_IDX(MDP_SSPP_TOP0_INTR2, 13),
> + },
> +};
> +
> static const struct dpu_ctl_cfg msm8998_ctl[] = {
> {
> .name = "ctl_0", .id = CTL_0,
> @@ -708,6 +801,25 @@ static const struct dpu_ctl_cfg qcm2290_ctl[] = {
>
> /* SSPP common configuration */
>
> +#define _VIG_SBLK_8996(num, sdma_pri, qseed_ver) \
> + { \
> + .maxdwnscale = MAX_DOWNSCALE_RATIO, \
> + .maxupscale = MAX_UPSCALE_RATIO, \
> + .smart_dma_priority = sdma_pri, \
> + .src_blk = {.name = STRCAT("sspp_src_", num), \
> + .id = DPU_SSPP_SRC, .base = 0x00, .len = 0x150,}, \
> + .scaler_blk = {.name = STRCAT("sspp_scaler", num), \
> + .id = qseed_ver, \
> + .base = 0x200, .len = 0xa0,}, \
> + .csc_blk = {.name = STRCAT("sspp_csc", num), \
> + .id = DPU_SSPP_CSC, \
> + .base = 0x320, .len = 0x100,}, \
> + .format_list = plane_formats_yuv, \
> + .num_formats = ARRAY_SIZE(plane_formats_yuv), \
> + .virt_format_list = plane_formats, \
> + .virt_num_formats = ARRAY_SIZE(plane_formats), \
> + }
> +
> #define _VIG_SBLK(num, sdma_pri, qseed_ver) \
> { \
> .maxdwnscale = MAX_DOWNSCALE_RATIO, \
> @@ -740,6 +852,15 @@ static const struct dpu_ctl_cfg qcm2290_ctl[] = {
> .virt_num_formats = ARRAY_SIZE(plane_formats), \
> }
>
> +static const struct dpu_sspp_sub_blks msm8996_vig_sblk_0 =
> + _VIG_SBLK_8996("0", 0, DPU_SSPP_SCALER_QSEED3);
> +static const struct dpu_sspp_sub_blks msm8996_vig_sblk_1 =
> + _VIG_SBLK_8996("1", 0, DPU_SSPP_SCALER_QSEED3);
> +static const struct dpu_sspp_sub_blks msm8996_vig_sblk_2 =
> + _VIG_SBLK_8996("2", 0, DPU_SSPP_SCALER_QSEED3);
> +static const struct dpu_sspp_sub_blks msm8996_vig_sblk_3 =
> + _VIG_SBLK_8996("3", 0, DPU_SSPP_SCALER_QSEED3);
> +
> static const struct dpu_sspp_sub_blks msm8998_vig_sblk_0 =
> _VIG_SBLK("0", 0, DPU_SSPP_SCALER_QSEED3);
> static const struct dpu_sspp_sub_blks msm8998_vig_sblk_1 =
> @@ -775,6 +896,30 @@ static const struct dpu_sspp_sub_blks sdm845_dma_sblk_3 = _DMA_SBLK("11", 4);
> .clk_ctrl = _clkctrl \
> }
>
> +static const struct dpu_sspp_cfg msm8996_sspp[] = {
> + SSPP_BLK("sspp_0", SSPP_VIG0, 0x4000, 0x150, VIG_MSM8996_MASK,
> + msm8996_vig_sblk_0, 0, SSPP_TYPE_VIG, DPU_CLK_CTRL_VIG0),
> + SSPP_BLK("sspp_1", SSPP_VIG1, 0x6000, 0x150, VIG_MSM8996_MASK,
> + msm8996_vig_sblk_1, 4, SSPP_TYPE_VIG, DPU_CLK_CTRL_VIG1),
> + SSPP_BLK("sspp_2", SSPP_VIG2, 0x8000, 0x150, VIG_MSM8996_MASK,
> + msm8996_vig_sblk_2, 8, SSPP_TYPE_VIG, DPU_CLK_CTRL_VIG2),
> + SSPP_BLK("sspp_3", SSPP_VIG3, 0xa000, 0x150, VIG_MSM8996_MASK,
> + msm8996_vig_sblk_3, 12, SSPP_TYPE_VIG, DPU_CLK_CTRL_VIG3),
> + /* TODO: RGB blocks */
> + SSPP_BLK("sspp_4", SSPP_RGB0, 0x14000, 0x150, RGB_MSM8996_MSK,
> + sdm845_dma_sblk_0, 1, SSPP_TYPE_RGB, DPU_CLK_CTRL_RGB0),
> + SSPP_BLK("sspp_5", SSPP_RGB1, 0x16000, 0x150, RGB_MSM8996_MSK,
> + sdm845_dma_sblk_1, 5, SSPP_TYPE_RGB, DPU_CLK_CTRL_RGB1),
> + SSPP_BLK("sspp_6", SSPP_RGB2, 0x18000, 0x150, RGB_MSM8996_MSK,
> + sdm845_dma_sblk_2, 9, SSPP_TYPE_RGB, DPU_CLK_CTRL_RGB2),
> + SSPP_BLK("sspp_7", SSPP_RGB3, 0x1a000, 0x150, RGB_MSM8996_MSK,
> + sdm845_dma_sblk_3, 13, SSPP_TYPE_RGB, DPU_CLK_CTRL_RGB3),
> + SSPP_BLK("sspp_8", SSPP_DMA0, 0x24000, 0x150, DMA_MSM8996_MASK,
> + sdm845_dma_sblk_0, 2, SSPP_TYPE_DMA, DPU_CLK_CTRL_DMA0),
> + SSPP_BLK("sspp_9", SSPP_DMA1, 0x26000, 0x150, DMA_MSM8996_MASK,
> + sdm845_dma_sblk_1, 10, SSPP_TYPE_DMA, DPU_CLK_CTRL_DMA1),
We must have cursor planes here. Otherwise there will be no hardware
cursor. On newer platforms we emulate them using DMA SSPPs. On msm8996
there were two special cursor planes (which supported just SRC, nothing
more). Let's have them here, unless there are issues with them.
> +};
> +
> static const struct dpu_sspp_cfg msm8998_sspp[] = {
> SSPP_BLK("sspp_0", SSPP_VIG0, 0x4000, 0x184, VIG_MSM8998_MASK,
> msm8998_vig_sblk_0, 0, SSPP_TYPE_VIG, DPU_CLK_CTRL_VIG0),
[skipped the rest]
--
With best wishes
Dmitry
More information about the dri-devel
mailing list