[PATCH v15 06/11] drm/mediatek: Add MT8195 External DisplayPort support
CK Hu
ck.hu at mediatek.com
Tue Aug 2 02:37:41 UTC 2022
Hi, Bo-Chen:
On Wed, 2022-07-27 at 12:50 +0800, Bo-Chen Chen wrote:
> From: Guillaume Ranquet <granquet at baylibre.com>
>
> This patch adds External DisplayPort support to the mt8195 eDP
> driver.
>
> Signed-off-by: Guillaume Ranquet <granquet at baylibre.com>
> Signed-off-by: Bo-Chen Chen <rex-bc.chen at mediatek.com>
> ---
> drivers/gpu/drm/mediatek/mtk_dp.c | 181 +++++++++++++++++++++---
> --
> drivers/gpu/drm/mediatek/mtk_dp_reg.h | 1 +
> 2 files changed, 146 insertions(+), 36 deletions(-)
>
> diff --git a/drivers/gpu/drm/mediatek/mtk_dp.c
> b/drivers/gpu/drm/mediatek/mtk_dp.c
> index 06eeecedd49e..ce817cb59445 100644
> --- a/drivers/gpu/drm/mediatek/mtk_dp.c
> +++ b/drivers/gpu/drm/mediatek/mtk_dp.c
> @@ -103,6 +103,11 @@ static struct regmap_config mtk_dp_regmap_config
> = {
> .name = "mtk-dp-registers",
> };
>
> +static bool mtk_dp_is_edp(struct mtk_dp *mtk_dp)
> +{
> + return mtk_dp->next_bridge;
For external DP, it could also connect to a bridge IC which transfer DP
to HDMI or some interface else. Use the compatible to judge this edp or
dp.
> +}
> +
> static struct mtk_dp *mtk_dp_from_bridge(struct drm_bridge *b)
> {
> return container_of(b, struct mtk_dp, bridge);
> @@ -341,6 +346,19 @@ static void mtk_dp_pg_enable(struct mtk_dp
> *mtk_dp, bool enable)
> 4 << PGEN_PATTERN_SEL_SHIFT,
> PGEN_PATTERN_SEL_MASK);
> }
>
> +static bool mtk_dp_plug_state(struct mtk_dp *mtk_dp)
> +{
> + return mtk_dp->train_info.cable_plugged_in;
> +}
> +
> +static bool mtk_dp_plug_state_avoid_pulse(struct mtk_dp *mtk_dp)
> +{
> + bool ret;
> +
> + return !(readx_poll_timeout(mtk_dp_plug_state, mtk_dp, ret,
> ret,
> + 4000, 7 * 4000));
> +}
> +
> static void mtk_dp_aux_irq_clear(struct mtk_dp *mtk_dp)
> {
> mtk_dp_write(mtk_dp, MTK_DP_AUX_P0_3640,
> @@ -778,35 +796,67 @@ static void mtk_dp_get_calibration_data(struct
> mtk_dp *mtk_dp)
> return;
> }
>
> - cal_data->glb_bias_trim =
> - check_cal_data_valid(mtk_dp, 1, 0x1e,
> - (buf[3] >> 27) & 0x1f, 0xf);
> - cal_data->clktx_impse =
> - check_cal_data_valid(mtk_dp, 1, 0xe,
> - (buf[0] >> 9) & 0xf, 0x8);
> - cal_data->ln_tx_impsel_pmos[0] =
> - check_cal_data_valid(mtk_dp, 1, 0xe,
> - (buf[2] >> 28) & 0xf, 0x8);
> - cal_data->ln_tx_impsel_nmos[0] =
> - check_cal_data_valid(mtk_dp, 1, 0xe,
> - (buf[2] >> 24) & 0xf, 0x8);
> - cal_data->ln_tx_impsel_pmos[1] =
> - check_cal_data_valid(mtk_dp, 1, 0xe,
> - (buf[2] >> 20) & 0xf, 0x8);
> - cal_data->ln_tx_impsel_nmos[1] =
> - check_cal_data_valid(mtk_dp, 1, 0xe,
> - (buf[2] >> 16) & 0xf, 0x8);
> - cal_data->ln_tx_impsel_pmos[2] =
> - check_cal_data_valid(mtk_dp, 1, 0xe,
> - (buf[2] >> 12) & 0xf, 0x8);
> - cal_data->ln_tx_impsel_nmos[2] =
> - check_cal_data_valid(mtk_dp, 1, 0xe,
> - (buf[2] >> 8) & 0xf, 0x8);
> - cal_data->ln_tx_impsel_pmos[3] =
> - check_cal_data_valid(mtk_dp, 1, 0xe,
> - (buf[2] >> 4) & 0xf, 0x8);
> - cal_data->ln_tx_impsel_nmos[3] =
> - check_cal_data_valid(mtk_dp, 1, 0xe, buf[2] & 0xf,
> 0x8);
> + if (mtk_dp_is_edp(mtk_dp)) {
> + cal_data->glb_bias_trim =
> + check_cal_data_valid(mtk_dp, 1, 0x1e,
> + (buf[3] >> 27) & 0x1f,
> 0xf);
> + cal_data->clktx_impse =
> + check_cal_data_valid(mtk_dp, 1, 0xe,
> + (buf[0] >> 9) & 0xf, 0x8);
> + cal_data->ln_tx_impsel_pmos[0] =
> + check_cal_data_valid(mtk_dp, 1, 0xe,
> + (buf[2] >> 28) & 0xf,
> 0x8);
> + cal_data->ln_tx_impsel_nmos[0] =
> + check_cal_data_valid(mtk_dp, 1, 0xe,
> + (buf[2] >> 24) & 0xf,
> 0x8);
> + cal_data->ln_tx_impsel_pmos[1] =
> + check_cal_data_valid(mtk_dp, 1, 0xe,
> + (buf[2] >> 20) & 0xf,
> 0x8);
> + cal_data->ln_tx_impsel_nmos[1] =
> + check_cal_data_valid(mtk_dp, 1, 0xe,
> + (buf[2] >> 16) & 0xf,
> 0x8);
> + cal_data->ln_tx_impsel_pmos[2] =
> + check_cal_data_valid(mtk_dp, 1, 0xe,
> + (buf[2] >> 12) & 0xf,
> 0x8);
> + cal_data->ln_tx_impsel_nmos[2] =
> + check_cal_data_valid(mtk_dp, 1, 0xe,
> + (buf[2] >> 8) & 0xf, 0x8);
> + cal_data->ln_tx_impsel_pmos[3] =
> + check_cal_data_valid(mtk_dp, 1, 0xe,
> + (buf[2] >> 4) & 0xf, 0x8);
> + cal_data->ln_tx_impsel_nmos[3] =
> + check_cal_data_valid(mtk_dp, 1, 0xe, buf[2] &
> 0xf, 0x8);
> + } else {
> + cal_data->glb_bias_trim =
> + check_cal_data_valid(mtk_dp, 1, 0x1e,
> + (buf[0] >> 27) & 0x1f,
> 0xf);
Why not place glb_bias_trim value in nvmem buf[3] for both edp and dp
case? Place in the same nvmem position, the driver code would be
simple.
> + cal_data->clktx_impse =
> + check_cal_data_valid(mtk_dp, 1, 0xe,
> + (buf[0] >> 13) & 0xf,
> 0x8);
> + cal_data->ln_tx_impsel_pmos[0] =
> + check_cal_data_valid(mtk_dp, 1, 0xe,
> + (buf[1] >> 28) & 0xf,
> 0x8);
> + cal_data->ln_tx_impsel_nmos[0] =
> + check_cal_data_valid(mtk_dp, 1, 0xe,
> + (buf[1] >> 24) & 0xf,
> 0x8);
> + cal_data->ln_tx_impsel_pmos[1] =
> + check_cal_data_valid(mtk_dp, 1, 0xe,
> + (buf[1] >> 20) & 0xf,
> 0x8);
> + cal_data->ln_tx_impsel_nmos[1] =
> + check_cal_data_valid(mtk_dp, 1, 0xe,
> + (buf[1] >> 16) & 0xf,
> 0x8);
> + cal_data->ln_tx_impsel_pmos[2] =
> + check_cal_data_valid(mtk_dp, 1, 0xe,
> + (buf[1] >> 12) & 0xf,
> 0x8);
> + cal_data->ln_tx_impsel_nmos[2] =
> + check_cal_data_valid(mtk_dp, 1, 0xe,
> + (buf[1] >> 8) & 0xf, 0x8);
> + cal_data->ln_tx_impsel_pmos[3] =
> + check_cal_data_valid(mtk_dp, 1, 0xe,
> + (buf[1] >> 4) & 0xf, 0x8);
> + cal_data->ln_tx_impsel_nmos[3] =
> + check_cal_data_valid(mtk_dp, 1, 0xe, buf[1] &
> 0xf, 0x8);
Why not place ln_tx_impsel_nmos and ln_tx_impsel_pmos value in nvmem
buf[2] for both edp and dp case? Place in the same nvmem position, the
driver code would be simple.
> + }
>
> kfree(buf);
> }
> @@ -926,7 +976,10 @@ static void mtk_dp_video_mute(struct mtk_dp
> *mtk_dp, bool enable)
> VIDEO_MUTE_SEL_DP_ENC0_P0_MASK |
> VIDEO_MUTE_SW_DP_ENC0_P0_MASK);
>
> - mtk_dp_sip_atf_call(mtk_dp, MTK_DP_SIP_ATF_EDP_VIDEO_UNMUTE,
> enable);
> + mtk_dp_sip_atf_call(mtk_dp,
> + mtk_dp_is_edp(mtk_dp) ?
> + MTK_DP_SIP_ATF_EDP_VIDEO_UNMUTE :
> + MTK_DP_SIP_ATF_VIDEO_UNMUTE, enable);
Use of_device_get_match_data to select MTK_DP_SIP_ATF_EDP_VIDEO_UNMUTE
or MTK_DP_SIP_ATF_VIDEO_UNMUTE.
> }
>
> static void mtk_dp_power_enable(struct mtk_dp *mtk_dp)
> @@ -1226,6 +1279,9 @@ static int mtk_dp_parse_capabilities(struct
> mtk_dp *mtk_dp)
> drm_dp_dpcd_writeb(&mtk_dp->aux, DP_SET_POWER,
> DP_SET_POWER_D0);
> usleep_range(2000, 5000);
>
> + if (!mtk_dp_plug_state(mtk_dp))
> + return -ENODEV;
> +
> drm_dp_read_dpcd_caps(&mtk_dp->aux, mtk_dp->rx_cap);
>
> train_info->link_rate = min_t(int, mtk_dp->max_linkrate,
> @@ -1277,6 +1333,9 @@ static int mtk_dp_train_start(struct mtk_dp
> *mtk_dp)
> u8 train_limit;
> u8 max_link_rate;
>
> + if (!mtk_dp_plug_state_avoid_pulse(mtk_dp))
> + return -ENODEV;
> +
> link_rate = mtk_dp->rx_cap[1];
> lane_count = mtk_dp->rx_cap[2] & 0x1F;
>
> @@ -1412,6 +1471,9 @@ static irqreturn_t mtk_dp_hpd_event_thread(int
> hpd, void *dev)
> {
> struct mtk_dp *mtk_dp = dev;
>
> + dev_dbg(mtk_dp->dev, "drm_helper_hpd_irq_event\n");
> + drm_helper_hpd_irq_event(mtk_dp->bridge.dev);
Because edp also have hpd interrupt, so I would like both edp and dp
have the same control flow for hdp. So move this to edp patch.
> +
> if (mtk_dp->train_info.hpd_inerrupt) {
> dev_dbg(mtk_dp->dev, "MTK_DP_HPD_INTERRUPT\n");
> mtk_dp->train_info.hpd_inerrupt = false;
> @@ -1452,9 +1514,20 @@ static irqreturn_t mtk_dp_hpd_event(int hpd,
> void *dev)
> else
> train_info->cable_plugged_in = false;
>
> - mtk_dp_update_bits(mtk_dp, MTK_DP_TOP_PWR_STATE,
> - DP_PWR_STATE_BANDGAP_TPLL_LANE,
> - DP_PWR_STATE_MASK);
> + if (!train_info->cable_plugged_in) {
> + mtk_dp_video_mute(mtk_dp, true);
> +
> + mtk_dp_initialize_priv_data(mtk_dp);
> + mtk_dp_set_idle_pattern(mtk_dp, true);
> +
> + mtk_dp_update_bits(mtk_dp,
> MTK_DP_TOP_PWR_STATE,
> + DP_PWR_STATE_BANDGAP_TPLL,
> + DP_PWR_STATE_MASK);
> + } else {
> + mtk_dp_update_bits(mtk_dp,
> MTK_DP_TOP_PWR_STATE,
> + DP_PWR_STATE_BANDGAP_TPLL_LA
> NE,
> + DP_PWR_STATE_MASK);
> + }
> }
>
> return IRQ_HANDLED;
> @@ -1499,6 +1572,24 @@ static int mtk_dp_dt_parse(struct mtk_dp
> *mtk_dp,
> return 0;
> }
>
> +static enum drm_connector_status mtk_dp_bdg_detect(struct drm_bridge
> *bridge)
> +{
> + struct mtk_dp *mtk_dp = mtk_dp_from_bridge(bridge);
> + enum drm_connector_status ret = connector_status_disconnected;
> + u8 sink_count = 0;
> +
> + if (mtk_dp_is_edp(mtk_dp))
> + return connector_status_connected;
Because edp also have hpd interrupt, so I would like both edp and dp
have the same control flow for hdp. So remove this.
> +
> + if (mtk_dp_plug_state_avoid_pulse(mtk_dp)) {
> + drm_dp_dpcd_readb(&mtk_dp->aux, DP_SINK_COUNT,
> &sink_count);
> + if (DP_GET_SINK_COUNT(sink_count))
> + ret = connector_status_connected;
> + }
> +
> + return ret;
> +}
> +
> static struct edid *mtk_dp_get_edid(struct drm_bridge *bridge,
> struct drm_connector *connector)
> {
> @@ -1512,7 +1603,8 @@ static struct edid *mtk_dp_get_edid(struct
> drm_bridge *bridge,
> drm_dp_dpcd_writeb(&mtk_dp->aux, DP_SET_POWER,
> DP_SET_POWER_D0);
> usleep_range(2000, 5000);
>
> - new_edid = drm_get_edid(connector, &mtk_dp->aux.ddc);
> + if (mtk_dp_plug_state(mtk_dp))
> + new_edid = drm_get_edid(connector, &mtk_dp->aux.ddc);
Please explain why only dp has this problem. If edp also has this
problem, move this to edp patch.
Regards,
CK
>
> if (!enabled)
> drm_bridge_chain_post_disable(bridge);
> @@ -1852,6 +1944,7 @@ static const struct drm_bridge_funcs
> mtk_dp_bridge_funcs = {
> .atomic_disable = mtk_dp_bridge_atomic_disable,
> .mode_valid = mtk_dp_bridge_mode_valid,
> .get_edid = mtk_dp_get_edid,
> + .detect = mtk_dp_bdg_detect,
> };
>
> static int mtk_dp_probe(struct platform_device *pdev)
> @@ -1873,9 +1966,15 @@ static int mtk_dp_probe(struct platform_device
> *pdev)
> "failed to request dp irq
> resource\n");
>
> mtk_dp->next_bridge = devm_drm_of_get_bridge(dev, dev->of_node,
> 1, 0);
> - if (IS_ERR(mtk_dp->next_bridge))
> + if (IS_ERR(mtk_dp->next_bridge) &&
> + PTR_ERR(mtk_dp->next_bridge) == -ENODEV) {
> + dev_info(dev,
> + "No panel connected in devicetree, continue as
> external DP\n");
> + mtk_dp->next_bridge = NULL;
> + } else if (IS_ERR(mtk_dp->next_bridge)) {
> return dev_err_probe(dev, PTR_ERR(mtk_dp->next_bridge),
> "Failed to get bridge\n");
> + }
>
> ret = mtk_dp_dt_parse(mtk_dp, pdev);
> if (ret)
> @@ -1918,7 +2017,10 @@ static int mtk_dp_probe(struct platform_device
> *pdev)
>
> mtk_dp->bridge.ops =
> DRM_BRIDGE_OP_DETECT | DRM_BRIDGE_OP_EDID |
> DRM_BRIDGE_OP_HPD;
> - mtk_dp->bridge.type = DRM_MODE_CONNECTOR_eDP;
> + if (mtk_dp_is_edp(mtk_dp))
> + mtk_dp->bridge.type = DRM_MODE_CONNECTOR_eDP;
> + else
> + mtk_dp->bridge.type = DRM_MODE_CONNECTOR_DisplayPort;
>
> drm_bridge_add(&mtk_dp->bridge);
>
> @@ -1945,6 +2047,12 @@ static int mtk_dp_suspend(struct device *dev)
> {
> struct mtk_dp *mtk_dp = dev_get_drvdata(dev);
>
> + if (mtk_dp_plug_state(mtk_dp)) {
> + drm_dp_dpcd_writeb(&mtk_dp->aux, DP_SET_POWER,
> DP_SET_POWER_D3);
> + /* Ensure the sink is off before shutting down power */
> + usleep_range(2000, 3000);
> + }
> +
> mtk_dp_power_disable(mtk_dp);
>
> mtk_dp_hwirq_enable(mtk_dp, false);
> @@ -1978,6 +2086,7 @@ static SIMPLE_DEV_PM_OPS(mtk_dp_pm_ops,
> mtk_dp_suspend, mtk_dp_resume);
>
> static const struct of_device_id mtk_dp_of_match[] = {
> { .compatible = "mediatek,mt8195-edp-tx" },
> + { .compatible = "mediatek,mt8195-dp-tx" },
> {},
> };
> MODULE_DEVICE_TABLE(of, mtk_dp_of_match);
> diff --git a/drivers/gpu/drm/mediatek/mtk_dp_reg.h
> b/drivers/gpu/drm/mediatek/mtk_dp_reg.h
> index 4ff8e9880dc9..59086eb82868 100644
> --- a/drivers/gpu/drm/mediatek/mtk_dp_reg.h
> +++ b/drivers/gpu/drm/mediatek/mtk_dp_reg.h
> @@ -14,6 +14,7 @@
> #define SEC_OFFSET 0x4000
>
> #define MTK_DP_SIP_ATF_EDP_VIDEO_UNMUTE (BIT(0) | BIT(5))
> +#define MTK_DP_SIP_ATF_VIDEO_UNMUTE BIT(5)
>
> #define DP_PHY_GLB_BIAS_GEN_00 0
> #define RG_XTP_GLB_BIAS_INTR_CTRL GENMASK(20, 16)
More information about the dri-devel
mailing list