[PATCH v2 4/4] drm/bridge: imx: add driver for HDMI TX Parallel Video Interface
Liu Ying
victor.liu at nxp.com
Sat Dec 17 09:27:40 UTC 2022
On Fri, 2022-12-16 at 22:07 +0100, Lucas Stach wrote:
> This IP block is found in the HDMI subsystem of the i.MX8MP SoC. It
> has a
> full timing generator and can switch between different video sources.
> On
> the i.MX8MP however the only supported source is the LCDIF. The block
> just needs to be powered up and told about the polarity of the video
> sync signals to act in bypass mode.
>
> Signed-off-by: Lucas Stach <l.stach at pengutronix.de>
> Tested-by: Marek Vasut <marex at denx.de>
> ---
> drivers/gpu/drm/bridge/imx/Kconfig | 7 +
> drivers/gpu/drm/bridge/imx/Makefile | 1 +
> drivers/gpu/drm/bridge/imx/imx8mp-hdmi-pvi.c | 202
> +++++++++++++++++++
> 3 files changed, 210 insertions(+)
> create mode 100644 drivers/gpu/drm/bridge/imx/imx8mp-hdmi-pvi.c
>
> diff --git a/drivers/gpu/drm/bridge/imx/Kconfig
> b/drivers/gpu/drm/bridge/imx/Kconfig
> index d828d8bfd893..e6cc4000bccd 100644
> --- a/drivers/gpu/drm/bridge/imx/Kconfig
> +++ b/drivers/gpu/drm/bridge/imx/Kconfig
> @@ -53,4 +53,11 @@ config DRM_IMX8MP_DW_HDMI_BRIDGE
> Choose this to enable support for the internal HDMI encoder
> found
> on the i.MX8MP SoC.
>
> +config DRM_IMX8MP_HDMI_PVI
Sort the config names alphabetically.
> + tristate "i.MX8MP HDMI PVI bridge support"
Add 'Freescale' before 'i.MX8MP' to show prompts in a consistent
fashion.
> + depends on OF
select DRM_KMS_HELPER
> + help
> + Choose this to enable support for the internal HDMI TX
> Parallel
> + Video Interface found on the i.MX8MP SoC.
> +
> endif # ARCH_MXC || COMPILE_TEST
> diff --git a/drivers/gpu/drm/bridge/imx/Makefile
> b/drivers/gpu/drm/bridge/imx/Makefile
> index 03b0074ae538..b0fd56550dad 100644
> --- a/drivers/gpu/drm/bridge/imx/Makefile
> +++ b/drivers/gpu/drm/bridge/imx/Makefile
> @@ -9,3 +9,4 @@ obj-$(CONFIG_DRM_IMX8QXP_PIXEL_LINK) += imx8qxp-
> pixel-link.o
> obj-$(CONFIG_DRM_IMX8QXP_PIXEL_LINK_TO_DPI) += imx8qxp-pxl2dpi.o
>
> obj-$(CONFIG_DRM_IMX8MP_DW_HDMI_BRIDGE) += imx8mp-hdmi.o
> +obj-$(CONFIG_DRM_IMX8MP_HDMI_PVI) += imx8mp-hdmi-pvi.o
Sort the config names alphabetically.
> diff --git a/drivers/gpu/drm/bridge/imx/imx8mp-hdmi-pvi.c
> b/drivers/gpu/drm/bridge/imx/imx8mp-hdmi-pvi.c
> new file mode 100644
> index 000000000000..30d40c21dabb
> --- /dev/null
> +++ b/drivers/gpu/drm/bridge/imx/imx8mp-hdmi-pvi.c
> @@ -0,0 +1,202 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +
> +/*
> + * Copyright (C) 2022 Pengutronix, Lucas Stach <
> kernel at pengutronix.de>
> + */
> +
> +#include <drm/drm_atomic_helper.h>
> +#include <drm/drm_bridge.h>
> +#include <drm/drm_crtc.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/of_graph.h>
> +#include <linux/pm_runtime.h>
Header files in linux/ come before those in drm/.
> +
> +#define HTX_PVI_CTL 0x0
Nitpick: One more tab between the macro and '0x0'.
> +#define PVI_CTL_OP_VSYNC_POL BIT(18)
> +#define PVI_CTL_OP_HSYNC_POL BIT(17)
> +#define PVI_CTL_OP_DE_POL BIT(16)
> +#define PVI_CTL_INP_VSYNC_POL BIT(14)
> +#define PVI_CTL_INP_HSYNC_POL BIT(13)
> +#define PVI_CTL_INP_DE_POL BIT(12)
> +#define PVI_CTL_INPUT_LCDIF BIT(2)
> +#define PVI_CTL_EN BIT(0)
> +
> +struct imx8mp_hdmi_pvi {
> + struct drm_bridge bridge;
> + struct device *dev;
> + struct drm_bridge *next_bridge;
> + void __iomem *regs;
> +};
> +
> +static inline struct imx8mp_hdmi_pvi *
> +to_imx8mp_hdmi_pvi(struct drm_bridge *bridge)
> +{
> + return container_of(bridge, struct imx8mp_hdmi_pvi, bridge);
> +}
> +
> +static int imx8mp_hdmi_pvi_bridge_attach(struct drm_bridge *bridge,
> + enum drm_bridge_attach_flags
> flags)
> +{
> + struct imx8mp_hdmi_pvi *pvi = to_imx8mp_hdmi_pvi(bridge);
> +
> + return drm_bridge_attach(bridge->encoder, pvi->next_bridge,
> + bridge, flags);
> +}
> +
> +static void imx8mp_hdmi_pvi_bridge_enable(struct drm_bridge *bridge,
> + struct drm_bridge_state
> *bridge_state)
> +{
> + struct drm_atomic_state *state = bridge_state->base.state;
> + struct imx8mp_hdmi_pvi *pvi = to_imx8mp_hdmi_pvi(bridge);
> + struct drm_connector_state *conn_state;
> + const struct drm_display_mode *mode;
> + struct drm_crtc_state *crtc_state;
> + struct drm_connector *connector;
> + u32 bus_flags, val;
> +
> + connector = drm_atomic_get_new_connector_for_encoder(state,
> bridge->encoder);
> + conn_state = drm_atomic_get_new_connector_state(state,
> connector);
> + crtc_state = drm_atomic_get_new_crtc_state(state, conn_state-
> >crtc);
> +
> + if (WARN_ON(pm_runtime_resume_and_get(pvi->dev)))
> + return;
> +
> + mode = &crtc_state->adjusted_mode;
> +
> + val = PVI_CTL_INPUT_LCDIF;
> +
> + if (mode->flags & DRM_MODE_FLAG_PVSYNC)
> + val |= PVI_CTL_OP_VSYNC_POL | PVI_CTL_INP_VSYNC_POL;
> +
> + if (mode->flags & DRM_MODE_FLAG_PHSYNC)
> + val |= PVI_CTL_OP_HSYNC_POL | PVI_CTL_INP_HSYNC_POL;
> +
> + if (pvi->next_bridge->timings)
> + bus_flags = pvi->next_bridge->timings->input_bus_flags;
> + else if (bridge_state)
> + bus_flags = bridge_state->input_bus_cfg.flags;
> +
> + if (bus_flags & DRM_BUS_FLAG_DE_HIGH)
> + val |= PVI_CTL_OP_DE_POL | PVI_CTL_INP_DE_POL;
Downstream kernel driver sets bit20 & bit21 to insert background color
when something wrong happens(maybe, it may mitigate the issue), not
sure if this driver should do the same or not.
> +
> + writel(val, pvi->regs + HTX_PVI_CTL);
> + val |= PVI_CTL_EN;
> + writel(val, pvi->regs + HTX_PVI_CTL);
> +}
> +
> +static void imx8mp_hdmi_pvi_bridge_disable(struct drm_bridge
> *bridge,
> + struct drm_bridge_state
> *bridge_state)
> +{
> + struct imx8mp_hdmi_pvi *pvi = to_imx8mp_hdmi_pvi(bridge);
> +
> + writel(0x0, pvi->regs + HTX_PVI_CTL);
> +
> + pm_runtime_put(pvi->dev);
> +}
> +
> +static u32 *imx8mp_hdmi_pvi_bridge_get_input_bus_fmts(struct
> drm_bridge *bridge,
> + struct drm_bridge_state
> *bridge_state,
> + struct drm_crtc_state
> *crtc_state,
> + struct drm_connector_state
> *conn_state,
> + u32 output_fmt,
> + unsigned int *num_input_fmts)
Please fix the checkpatch.pl warning with --strict parameter:
CHECK: Alignment should match open parenthesis
#151: FILE: drivers/gpu/drm/bridge/imx/imx8mp-hdmi-pvi.c:99:
+static u32 *imx8mp_hdmi_pvi_bridge_get_input_bus_fmts(struct
drm_bridge *bridge,
+ struct drm_bridge_state
*bridge_state,
> +{
> + struct imx8mp_hdmi_pvi *pvi = to_imx8mp_hdmi_pvi(bridge);
> + struct drm_bridge *next_bridge = pvi->next_bridge;
> + struct drm_bridge_state *next_state;
> +
> + if (!next_bridge->funcs->atomic_get_input_bus_fmts)
> + return 0;
> +
> + next_state = drm_atomic_get_new_bridge_state(crtc_state->state,
> + next_bridge);
> +
> + return next_bridge->funcs-
> >atomic_get_input_bus_fmts(next_bridge,
> + next_state
> ,
> + crtc_state
> ,
> + conn_state
> ,
> + output_fmt
> ,
> + num_input_
> fmts);
> +}
> +
> +static const struct drm_bridge_funcs imx_hdmi_pvi_bridge_funcs = {
> + .attach = imx8mp_hdmi_pvi_bridge_attach,
> + .atomic_enable = imx8mp_hdmi_pvi_bridge_enable,
> + .atomic_disable = imx8mp_hdmi_pvi_bridge_disable,
> + .atomic_get_input_bus_fmts =
> imx8mp_hdmi_pvi_bridge_get_input_bus_fmts,
> + .atomic_duplicate_state =
> drm_atomic_helper_bridge_duplicate_state,
> + .atomic_destroy_state = drm_atomic_helper_bridge_destroy_state,
> + .atomic_reset = drm_atomic_helper_bridge_reset,
> +};
> +
> +static int imx8mp_hdmi_pvi_probe(struct platform_device *pdev)
> +{
> + struct device_node *remote;
> + struct imx8mp_hdmi_pvi *pvi;
> +
> + pvi = devm_kzalloc(&pdev->dev, sizeof(*pvi), GFP_KERNEL);
> + if (!pvi)
> + return -ENOMEM;
> +
> + platform_set_drvdata(pdev, pvi);
> + pvi->dev = &pdev->dev;
> +
> + pvi->regs = devm_platform_ioremap_resource(pdev, 0);
> + if (IS_ERR(pvi->regs))
> + return PTR_ERR(pvi->regs);
> +
> + /* Get the next bridge in the pipeline. */
> + remote = of_graph_get_remote_node(pdev->dev.of_node, 1, -1);
> + if (!remote)
> + return -EINVAL;
> +
> + pvi->next_bridge = of_drm_find_bridge(remote);
> + of_node_put(remote);
> +
> + if (!pvi->next_bridge)
> + return dev_err_probe(&pdev->dev, -EPROBE_DEFER,
> + "could not find next bridge\n");
> +
> + /* Register the bridge. */
> + pvi->bridge.funcs = &imx_hdmi_pvi_bridge_funcs;
> + pvi->bridge.of_node = pdev->dev.of_node;
> + pvi->bridge.timings = pvi->next_bridge->timings;
> +
> + drm_bridge_add(&pvi->bridge);
> +
> + pm_runtime_enable(&pdev->dev);
> +
> + return 0;
> +}
> +
> +static int imx8mp_hdmi_pvi_remove(struct platform_device *pdev)
> +{
> + struct imx8mp_hdmi_pvi *pvi = platform_get_drvdata(pdev);
> +
> + drm_bridge_remove(&pvi->bridge);
Missing the function call for pm_runtime_disable().
> +
> + return 0;
> +}
> +
> +static const struct of_device_id imx8mp_hdmi_pvi_match[] = {
> + {
> + .compatible = "fsl,imx8mp-hdmi-pvi",
> + }, {
> + /* sentinel */
> + },
Nitpick: ',' after the sentinel is not needed since it's the last one.
Regards,
Liu Ying
> +};
> +MODULE_DEVICE_TABLE(of, imx8mp_hdmi_pvi_match);
> +
> +static struct platform_driver imx8mp_hdmi_pvi_driver = {
> + .probe = imx8mp_hdmi_pvi_probe,
> + .remove = imx8mp_hdmi_pvi_remove,
> + .driver = {
> + .name = "imx-hdmi-pvi",
> + .of_match_table = imx8mp_hdmi_pvi_match,
> + },
> +};
> +module_platform_driver(imx8mp_hdmi_pvi_driver);
> +
> +MODULE_DESCRIPTION("i.MX8MP HDMI TX Parallel Video Interface bridge
> driver");
> +MODULE_LICENSE("GPL");
More information about the dri-devel
mailing list