[PATCH v7 10/24] drm/rockchip: dw_hdmi: Add support for hclk
Dmitry Osipenko
dmitry.osipenko at collabora.com
Tue Mar 1 13:22:29 UTC 2022
On 3/1/22 11:37, Sascha Hauer wrote:
> On Tue, Mar 01, 2022 at 01:56:59AM +0300, Dmitry Osipenko wrote:
>> On 2/28/22 17:19, Sascha Hauer wrote:
>>> On Fri, Feb 25, 2022 at 02:11:54PM +0100, Sascha Hauer wrote:
>>>> On Fri, Feb 25, 2022 at 12:41:23PM +0000, Robin Murphy wrote:
>>>>> On 2022-02-25 11:10, Dmitry Osipenko wrote:
>>>>>> 25.02.2022 13:49, Sascha Hauer пишет:
>>>>>>> On Fri, Feb 25, 2022 at 01:26:14PM +0300, Dmitry Osipenko wrote:
>>>>>>>> 25.02.2022 10:51, Sascha Hauer пишет:
>>>>>>>>> The rk3568 HDMI has an additional clock that needs to be enabled for the
>>>>>>>>> HDMI controller to work. The purpose of that clock is not clear. It is
>>>>>>>>> named "hclk" in the downstream driver, so use the same name.
>>>>>>>>>
>>>>>>>>> Signed-off-by: Sascha Hauer <s.hauer at pengutronix.de>
>>>>>>>>> ---
>>>>>>>>>
>>>>>>>>> Notes:
>>>>>>>>> Changes since v5:
>>>>>>>>> - Use devm_clk_get_optional rather than devm_clk_get
>>>>>>>>>
>>>>>>>>> drivers/gpu/drm/rockchip/dw_hdmi-rockchip.c | 16 ++++++++++++++++
>>>>>>>>> 1 file changed, 16 insertions(+)
>>>>>>>>>
>>>>>>>>> diff --git a/drivers/gpu/drm/rockchip/dw_hdmi-rockchip.c b/drivers/gpu/drm/rockchip/dw_hdmi-rockchip.c
>>>>>>>>> index fe4f9556239ac..c6c00e8779ab5 100644
>>>>>>>>> --- a/drivers/gpu/drm/rockchip/dw_hdmi-rockchip.c
>>>>>>>>> +++ b/drivers/gpu/drm/rockchip/dw_hdmi-rockchip.c
>>>>>>>>> @@ -76,6 +76,7 @@ struct rockchip_hdmi {
>>>>>>>>> const struct rockchip_hdmi_chip_data *chip_data;
>>>>>>>>> struct clk *ref_clk;
>>>>>>>>> struct clk *grf_clk;
>>>>>>>>> + struct clk *hclk_clk;
>>>>>>>>> struct dw_hdmi *hdmi;
>>>>>>>>> struct regulator *avdd_0v9;
>>>>>>>>> struct regulator *avdd_1v8;
>>>>>>>>> @@ -229,6 +230,14 @@ static int rockchip_hdmi_parse_dt(struct rockchip_hdmi *hdmi)
>>>>>>>>> return PTR_ERR(hdmi->grf_clk);
>>>>>>>>> }
>>>>>>>>> + hdmi->hclk_clk = devm_clk_get_optional(hdmi->dev, "hclk");
>>>>>>>>> + if (PTR_ERR(hdmi->hclk_clk) == -EPROBE_DEFER) {
>>>>>>>>
>>>>>>>> Have you tried to investigate the hclk? I'm still thinking that's not
>>>>>>>> only HDMI that needs this clock and then the hardware description
>>>>>>>> doesn't look correct.
>>>>>>>
>>>>>>> I am still not sure what you mean. Yes, it's not only the HDMI that
>>>>>>> needs this clock. The VOP2 needs it as well and the driver handles that.
>>>>>>
>>>>>> I'm curious whether DSI/DP also need that clock to be enabled. If they
>>>>>> do, then you aren't modeling h/w properly AFAICS.
>>>>>
>>>>> Assuming nobody at Rockchip decided to make things needlessly inconsistent
>>>>> with previous SoCs, HCLK_VOP should be the clock for the VOP's AHB slave
>>>>> interface. Usually, if that affected anything other than accessing VOP
>>>>> registers, indeed it would smell of something being wrong in the clock tree,
>>>>> but in this case I'd also be suspicious of whether it might have ended up
>>>>> clocking related GRF registers as well (either directly, or indirectly via
>>>>> some gate that the clock driver hasn't modelled yet).
>>>>
>>>> Ok, I am beginning to understand. I verified that hdmi, mipi and dp are
>>>> hanging when HCLK_VOP is disabled by disabling that clock via sysfs
>>>> using CLOCK_ALLOW_WRITE_DEBUGFS. When it's disabled then the registers
>>>> of that units can't be accessed. However, when I disable HCLK_VOP by
>>>> directly writing to the gate bit RK3568_CLKGATE_CON(20) then only
>>>> accessing VOP registers hangs, the other units stay functional.
>>>> So it seems it must be the parent clock which must be enabled. The
>>>> parent clock is hclk_vo. This clock should be handled as part of the
>>>> RK3568_PD_VO power domain:
>>>>
>>>> power-domain at RK3568_PD_VO {
>>>> reg = <RK3568_PD_VO>;
>>>> clocks = <&cru HCLK_VO>,
>>>> <&cru PCLK_VO>,
>>>> <&cru ACLK_VOP_PRE>;
>>>> pm_qos = <&qos_hdcp>,
>>>> <&qos_vop_m0>,
>>>> <&qos_vop_m1>;
>>>> #power-domain-cells = <0>;
>>>> };
>>>
>>> Forget this. The clocks in this node are only enabled during enabling or
>>> disabling the power domain, they are disabled again immediately afterwards.
>>>
>>> OK, I need HCLK_VO to access the HDMI registers. I verified that by
>>> disabling HCLK_VO at register level (CRU_GATE_CON(20) BIT(1)). The
>>> HDMI registers become inaccessible then. This means I'll replace
>>> HCLK_VOP in the HDMI node with HCLK_VO. Does this sound sane?
>>
>> The RK3568_PD_VO already has HCLK_VO and the domain should be
>> auto-enabled before HDMI registers are accessed,
>
> As said, the clocks given in the power domain are only enabled during
> the process of enabling/disabling the power domain and are disabled
> again directly afterwards:
>
>> if (rockchip_pmu_domain_is_on(pd) != power_on) {
>
> They are enabled here:
>
>> ret = clk_bulk_enable(pd->num_clks, pd->clks);
>> if (ret < 0) {
>> dev_err(pmu->dev, "failed to enable clocks\n");
>> mutex_unlock(&pmu->mutex);
>> return ret;
>> }
>>
>> if (!power_on) {
>> rockchip_pmu_save_qos(pd);
>>
>> /* if powering down, idle request to NIU first */
>> rockchip_pmu_set_idle_request(pd, true);
>> }
>>
>
> Then the power domain is switched:
>
>> rockchip_do_pmu_set_power_domain(pd, power_on);
>>
>> if (power_on) {
>> /* if powering up, leave idle mode */
>> rockchip_pmu_set_idle_request(pd, false);
>>
>> rockchip_pmu_restore_qos(pd);
>> }
>>
>
> And here the clocks are disabled again:
>
>> clk_bulk_disable(pd->num_clks, pd->clks);
>> }
>
>> hence you should do the
>> opposite and remove the HCLK_VO/P clock from the HDMI DT, not add it. If
>> the HCLK_VO clock isn't enabled by the domain driver, then you need to
>> check why. Or am I missing something?
>
> What the power domain driver additionally does is: It does a of_clk_get()
> on all the clocks found in the node of a power domains consumer. It then
> does a pm_clk_add_clk() on the clocks and sets the GENPD_FLAG_PM_CLK
> flag. This has the effect that all clocks of a device in a power domain
> are enabled as long as the power domain itself is enabled. This means
> when I just add HCLK_VO to the DSI node, then the power domain driver
> will enable it, even when the clock is not touched in the DSI driver at
> all. To me this looks really fishy because I think a device itself
> should have control over its clocks. I don't know how many devices
> really depend on the power domain driver controlling their clocks, but
> everyone of them will stop working when the power domain driver is not
> compiled in.
This is a correct behaviour of the GENPD driver. Thank you for the
clarification, I completely forgot that clocks should be kept disabled
by GENPD after power-on.
Now I see why you want to add HCLK_VO to the HDMI node, it's good to me
to add the HCLK_VO to the HDMI node. You may copy this clarification to
the commit message of the HDMI DT patch in v8.
I think it's okay that PD driver uses pm_clk_add_clk(). Shouldn't be a
problem to change that later on if some specific driver will want to
have an explicit control over clocks.
But yes, CONFIG_ROCKCHIP_PM_DOMAINS must be enabled (auto-selected?). Is
ARCH_ROCKCHIP available on ARM64 at all?
>> What about DSI and DP? Don't they depend on RK3568_PD_VO as well?
>
> Yes, they depend on that power domain as well.
So DSI/DP bindings will require a similar HCLK_VO change. You're not
using DP/DSI in this patchset, hence should be okay to postpone the
DSI/DP changes if you don't want to touch them for now.
Seems nothing holds back you now from making the v8.
More information about the dri-devel
mailing list