[PATCH v2] drm/bridge: anx7625: Set downstream sink into normal status

[Xin Ji]

On Tue, Mar 22, 2022 at 05:16:43PM +0800, Chen-Yu Tsai wrote:
> On Tue, Mar 22, 2022 at 4:52 PM Xin Ji <xji at analogixsemi.com> wrote:
> >
> > On Tue, Mar 22, 2022 at 04:43:20PM +0800, Hsin-Yi Wang wrote:
> > > On Tue, Mar 22, 2022 at 4:02 PM Xin Ji <xji at analogixsemi.com> wrote:
> > > >
> > > > As downstream sink was set into standby mode while bridge disabled,
> > > > this patch used for setting downstream sink into normal status
> > > > while enable bridge.
> > > >
> > > > Signed-off-by: Xin Ji <xji at analogixsemi.com>
> > > > Reviewed-by: Pin-Yen Lin <treapking at chromium.org>
> > > >
> > > > ---
> > > > V1 -> V2: use dev_dbg replace of dev_info
> > > > ---
> > > >  drivers/gpu/drm/bridge/analogix/anx7625.c | 8 ++++++++
> > > >  1 file changed, 8 insertions(+)
> > > >
> > > > diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.c b/drivers/gpu/drm/bridge/analogix/anx7625.c
> > > > index 9a2a19ad4202..dcf3275a00fe 100644
> > > > --- a/drivers/gpu/drm/bridge/analogix/anx7625.c
> > > > +++ b/drivers/gpu/drm/bridge/analogix/anx7625.c
> > > > @@ -924,12 +924,20 @@ static void anx7625_dp_start(struct anx7625_data *ctx)
> > > >  {
> > > >         int ret;
> > > >         struct device *dev = &ctx->client->dev;
> > > > +       u8 data;
> > > >
> > > >         if (!ctx->display_timing_valid) {
> > > >                 DRM_DEV_ERROR(dev, "mipi not set display timing yet.\n");
> > > >                 return;
> > > >         }
> > > >
> > > > +       dev_dbg(dev, "set downstream sink into normal\n");
> > > > +       /* Downstream sink enter into normal mode */
> > > > +       data = 1;
> > > > +       ret = anx7625_aux_trans(ctx, DP_AUX_NATIVE_WRITE, 0x000600, 1, &data);
> > > > +       if (ret < 0)
> > > > +               dev_err(dev, "IO error : set sink into normal mode fail\n");
> > > > +
> > >
> > > The driver uses DRM_DEV_* for logs. Can we use this?
> > Hi Hsin-Yi, as comment in drm/drm_print.h:
> > "NOTE: this is deprecated in favor of drm_dbg". DRM bridge driver not
> > use DRM_DEV_* any more. I'll send a patch to replace all of DRM_DEV_*
> > later.
> 
> drm_dbg is better than dev_dbg though. With the former, you still get the
> option to control it with the drm.debug module parameter, unlike the latter
> which normally gets compiled out.
> 
> Please use drm_dbg*.
> 
> ChenYu

Hi ChenYu, the parameter of drm_dbg is "drm", if use drm_dbg, it will
change more code, I'll consider to upstream new patch to replace all of
them later.

Thanks,
Xin
> 
> > Thanks,
> > Xin
> > >
> > > >         /* Disable HDCP */
> > > >         anx7625_write_and(ctx, ctx->i2c.rx_p1_client, 0xee, 0x9f);
> > > >
> > > > --
> > > > 2.25.1
> > > >