[PATCH v13 3/6] dt-bindings: display: Add Loongson display controller
Sui Jingfeng
15330273260 at 189.cn
Sun Mar 27 14:40:18 UTC 2022
Add DT bindings and simple usages for Loongson display controller
found in LS7A1000 bridge chip and LS2k1000 SoC.
Signed-off-by: Sui Jingfeng <15330273260 at 189.cn>
---
.../loongson/loongson,display-controller.yaml | 321 ++++++++++++++++++
1 file changed, 321 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/loongson/loongson,display-controller.yaml
diff --git a/Documentation/devicetree/bindings/display/loongson/loongson,display-controller.yaml b/Documentation/devicetree/bindings/display/loongson/loongson,display-controller.yaml
new file mode 100644
index 000000000000..34060ed55a25
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/loongson/loongson,display-controller.yaml
@@ -0,0 +1,321 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/loongson/loongson,display-controller.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Loongson LS7A1000/LS2K1000/LS2K0500 Display Controller Device Tree Bindings
+
+maintainers:
+ - Sui Jingfeng <suijingfeng at loongson.cn>
+
+description: |+
+
+ Loongson display controllers are simple which require scanout buffers
+ to be physically contiguous. LS2K1000/LS2K0500 is a SOC, only system
+ memory is available. LS7A1000/LS7A2000 is bridge chip which is equipped
+ with a dedicated video RAM which is 64MB or more, precise size can be
+ read from the PCI BAR 2 of the GPU device(0x0014:0x7A15) in the bridge
+ chip.
+
+ LSDC has two display pipes, each way has a DVO interface which provide
+ RGB888 signals, vertical & horizontal synchronisations, data enable and
+ the pixel clock. LSDC has two CRTC, each CRTC is able to scanout from
+ 1920x1080 resolution at 60Hz. Each CRTC has two FB address registers.
+
+ For LS7A1000, there are 4 dedicated GPIOs whose control register is
+ located at the DC register space. They are used to emulate two way i2c,
+ One for DVO0, another for DVO1.
+
+ LS2K1000 and LS2K0500 SoC grab i2c adapter from other module, either
+ general purpose GPIO emulated i2c or hardware i2c in the SoC.
+
+ LSDC's display pipeline have several components as below description,
+
+ The display controller in LS7A1000:
+ ___________________ _________
+ | -------| | |
+ | CRTC0 --> | DVO0 ----> Encoder0 ---> Connector0 ---> | Monitor |
+ | _ _ -------| ^ ^ |_________|
+ | | | | | -------| | |
+ | |_| |_| | i2c0 <--------+-------------+
+ | -------|
+ | DC IN LS7A1000 |
+ | _ _ -------|
+ | | | | | | i2c1 <--------+-------------+
+ | |_| |_| -------| | | _________
+ | -------| | | | |
+ | CRTC1 --> | DVO1 ----> Encoder1 ---> Connector1 ---> | Panel |
+ | -------| |_________|
+ |___________________|
+
+ Simple usage of LS7A1000 with LS3A4000 CPU:
+
+ +------+ +------------------------------------+
+ | DDR4 | | +-------------------+ |
+ +------+ | | PCIe Root complex | LS7A1000 |
+ || MC0 | +--++---------++----+ |
+ +----------+ HT 3.0 | || || |
+ | LS3A4000 |<-------->| +---++---+ +--++--+ +---------+ +------+
+ | CPU |<-------->| | GC1000 | | LSDC |<--->| DDR3 MC |<->| VRAM |
+ +----------+ | +--------+ +-+--+-+ +---------+ +------+
+ || MC1 +---------------|--|-----------------+
+ +------+ | |
+ | DDR4 | +-------+ DVO0 | | DVO1 +------+
+ +------+ VGA <--|ADV7125|<--------+ +-------->|TFP410|--> DVI/HDMI
+ +-------+ +------+
+
+ The display controller in LS2K1000/LS2K0500:
+ ___________________ _________
+ | -------| | |
+ | CRTC0 --> | DVO0 ----> Encoder0 ---> Connector0 ---> | Monitor |
+ | _ _ -------| ^ ^ |_________|
+ | | | | | | | |
+ | |_| |_| | +------+ |
+ | <---->| i2c0 |<---------+
+ | DC IN LS2K1000 | +------+
+ | _ _ | +------+
+ | | | | | <---->| i2c1 |----------+
+ | |_| |_| | +------+ | _________
+ | -------| | | | |
+ | CRTC1 --> | DVO1 ----> Encoder1 ---> Connector1 ---> | Panel |
+ | -------| |_________|
+ |___________________|
+
+properties:
+ $nodename:
+ pattern: "^display-controller@[0-9a-f],[0-9a-f]$"
+
+ compatible:
+ oneOf:
+ - items:
+ - enum:
+ - loongson,ls7a1000-dc
+ - loongson,ls2k1000-dc
+ - loongson,ls2k0500-dc
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ '#address-cells':
+ const: 1
+
+ '#size-cells':
+ const: 0
+
+ i2c at 6:
+ $ref: /schemas/i2c/i2c-controller.yaml#
+ description: |
+ Built-in GPIO emulate i2c exported for display bridge configuration,
+ monitor detection and edid read back etc, for ls7a1000 only.
+
+ properties:
+ $nodename:
+ const: i2c
+
+ compatible:
+ const: loongson,gpio-i2c
+
+ reg:
+ minItems: 1
+ description: address offset and range
+
+ loongson,nr:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: Indicates the I2C bus number this DT node represents.
+
+ loongson,sda:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: gpio pin used for the sda signal
+
+ loongson,scl:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: gpio pin used for the scl signal
+
+ loongson,udelay:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: delay between GPIO operations, unit is us.
+
+ loongson,timeout:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: timeout to get data, unit is ms.
+
+ required:
+ - compatible
+ - loongson,sda
+ - loongson,scl
+ - loongson,nr
+
+ i2c at 7:
+ $ref: /schemas/i2c/i2c-controller.yaml#
+ description: |
+ Built-in GPIO emulate i2c exported for display bridge configuration,
+ monitor detection and edid read back etc, for ls7a1000 only.
+ properties:
+ $nodename:
+ const: i2c
+
+ compatible:
+ const: loongson,gpio-i2c
+
+ reg:
+ minItems: 1
+ description: address offset and range
+
+ loongson,nr:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: Indicates the I2C bus number this DT node represents.
+
+ loongson,sda:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: gpio pin used for the sda signal
+
+ loongson,scl:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: gpio pin used for the scl signal
+
+ loongson,udelay:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: delay between GPIO operations, unit is us.
+
+ loongson,timeout:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: timeout to get data, unit is ms.
+
+ required:
+ - compatible
+ - loongson,sda
+ - loongson,scl
+ - loongson,nr
+
+ ports:
+ $ref: /schemas/graph.yaml#/properties/ports
+
+ properties:
+ port at 0:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: output port node connected with DPI panels or external encoders, with only one endpoint.
+
+ port at 1:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: output port node connected with DPI panels or external encoders, with only one endpoint.
+
+ required:
+ - port at 0
+ - port at 1
+
+required:
+ - compatible
+ - reg
+ - interrupts
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ bus {
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <2>;
+
+ display-controller at 6,1 {
+ compatible = "loongson,ls7a1000-dc";
+ reg = <0x3100 0x0 0x0 0x0 0x0>;
+ interrupts = <28 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ bus {
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <2>;
+
+ display-controller at 6,1 {
+ compatible = "loongson,ls7a1000-dc";
+ reg = <0x3100 0x0 0x0 0x0 0x0>;
+ interrupts = <28 IRQ_TYPE_LEVEL_HIGH>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c at 6 {
+ compatible = "loongson,gpio-i2c";
+ reg = <0x00001650 0x00000020>;
+ loongson,nr = <6>;
+ loongson,sda = <0>;
+ loongson,scl = <1>;
+ loongson,udelay = <5>;
+ loongson,timeout = <2200>;
+ };
+
+ i2c at 7 {
+ compatible = "loongson,gpio-i2c";
+ reg = <0x00001650 0x00000020>;
+ loongson,nr = <7>;
+ loongson,sda = <2>;
+ loongson,scl = <3>;
+ loongson,udelay = <5>;
+ loongson,timeout = <2200>;
+ };
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port at 0 {
+ reg = <0>;
+ endpoint {
+ remote-endpoint = <&vga_encoder_in>;
+ };
+ };
+
+ port at 1 {
+ reg = <1>;
+ endpoint {
+ remote-endpoint = <&dvi_encoder_in>;
+ };
+ };
+ };
+ };
+ };
+
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ bus {
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <2>;
+
+ display-controller at 6,0 {
+ compatible = "loongson,ls2k1000-dc";
+ reg = <0x3100 0x0 0x0 0x0 0x0>;
+ interrupts = <28 IRQ_TYPE_LEVEL_HIGH>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port at 0 {
+ reg = <0>;
+ endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+
+ port at 1 {
+ reg = <1>;
+ endpoint {
+ remote-endpoint = <&hdmi_encoder_in>;
+ };
+ };
+ };
+ };
+ };
+...
--
2.25.1
More information about the dri-devel
mailing list