[PATCH] dt-bindings: display: msm: dsi: remove address/size cells

[Vinod Koul]

On 28-03-22, 13:21, Rob Herring wrote:
> On Mon, Mar 28, 2022 at 12:18 PM Krzysztof Kozlowski
> <krzysztof.kozlowski at linaro.org> wrote:
> >
> > On 28/03/2022 19:16, Vinod Koul wrote:
> > > On 28-03-22, 19:43, Dmitry Baryshkov wrote:
> > >> On Mon, 28 Mar 2022 at 18:30, Krzysztof Kozlowski
> > >> <krzysztof.kozlowski at linaro.org> wrote:
> > >>>
> > >>> The DSI node is not a bus and the children do not have unit addresses.
> > >>>
> > >>> Reported-by: Vinod Koul <vkoul at kernel.org>
> > >>> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski at linaro.org>
> > >>
> > >> NAK.
> > >> DSI panels are children of the DSI device tree node with the reg = <0>; address.
> > >> This is the convention used by other platforms too (see e.g.
> > >> arch/arm64/boot/dts/freescale/imx8mq-evk.dts).
> > >
> > > So we should add reg = 0, i will update my dtsi fix
> > >
> >
> > To "ports" node? No. The reg=0 is for children of the bus, so the
> > panels. How to combine both without warnings - ports and panel at 0 - I
> > don't know yet...
> 
> I don't think that should case a warning. Or at least it's one we turn off.

Well in this case I think we might need a fix:
Here is the example quoted in the binding. We have ports{} and then the
two port at 0 and port at 1 underneath.

So it should be okay to drop #address-cells/#size-cells from dsi node
but keep in ports node...

Thoughts...?


     dsi at ae94000 {
           compatible = "qcom,mdss-dsi-ctrl";
           reg = <0x0ae94000 0x400>;
           reg-names = "dsi_ctrl";

           #address-cells = <1>;
           #size-cells = <0>;

           interrupt-parent = <&mdss>;
           interrupts = <4>;

           clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
                    <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
                    <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
                    <&dispcc DISP_CC_MDSS_ESC0_CLK>,
                    <&dispcc DISP_CC_MDSS_AHB_CLK>,
                    <&dispcc DISP_CC_MDSS_AXI_CLK>;
           clock-names = "byte",
                         "byte_intf",
                         "pixel",
                         "core",
                         "iface",
                         "bus";

           phys = <&dsi0_phy>;
           phy-names = "dsi";

           assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
           assigned-clock-parents = <&dsi_phy 0>, <&dsi_phy 1>;

           power-domains = <&rpmhpd SC7180_CX>;
           operating-points-v2 = <&dsi_opp_table>;

           ports {
                  #address-cells = <1>;
                  #size-cells = <0>;

                  port at 0 {
                          reg = <0>;
                          dsi0_in: endpoint {
                                   remote-endpoint = <&dpu_intf1_out>;
                          };
                  };

                  port at 1 {
                          reg = <1>;
                          dsi0_out: endpoint {
                                   remote-endpoint = <&sn65dsi86_in>;
                                   data-lanes = <0 1 2 3>;
                          };
                  };
           };
     };

> 
> Rob

-- 
~Vinod