[PATCH v1 2/5] arm64: dts: qcom: sm8450: add display hardware devices

Konrad Dybcio konrad.dybcio at somainline.org
Fri Nov 4 14:15:50 UTC 2022


On 04/11/2022 14:13, Dmitry Baryshkov wrote:
> Add devices tree nodes describing display hardware on SM8450:
> - Display Clock Controller
> - MDSS
> - MDP
> - two DSI controllers and DSI PHYs
>
> This does not provide support for DP controllers present on SM8450.
>
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov at linaro.org>
> ---
>   arch/arm64/boot/dts/qcom/sm8450.dtsi | 284 ++++++++++++++++++++++++++-
>   1 file changed, 280 insertions(+), 4 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
> index 250e6b883ca3..23f989dedfdb 100644
> --- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
> @@ -2401,6 +2401,282 @@ camcc: clock-controller at ade0000 {
>   			status = "disabled";
>   		};
>   
> +		mdss: mdss at ae00000 {
> +			compatible = "qcom,sm8450-mdss";
> +			reg = <0 0x0ae00000 0 0x1000>;
> +			reg-names = "mdss";
> +
> +			/* same path used twice */
> +			interconnects = <&mmss_noc MASTER_MDP_DISP 0 &mc_virt SLAVE_EBI1_DISP 0>,
> +					<&mmss_noc MASTER_MDP_DISP 0 &mc_virt SLAVE_EBI1_DISP 0>;
> +			interconnect-names = "mdp0-mem", "mdp1-mem";
> +
> +			resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;
> +
> +			power-domains = <&dispcc MDSS_GDSC>;
> +
> +			clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> +				 <&gcc GCC_DISP_HF_AXI_CLK>,
> +				 <&gcc GCC_DISP_SF_AXI_CLK>,
> +				 <&dispcc DISP_CC_MDSS_MDP_CLK>;
> +			clock-names = "iface", "bus", "nrt_bus", "core";
> +
> +			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-controller;
> +			#interrupt-cells = <1>;
> +
> +			iommus = <&apps_smmu 0x2800 0x402>;
> +
> +			status = "disabled";
> +
> +			#address-cells = <2>;
> +			#size-cells = <2>;
> +			ranges;
> +
> +			mdss_mdp: mdp at ae01000 {
> +				compatible = "qcom,sm8450-dpu";
> +				reg = <0 0x0ae01000 0 0x8f000>,
> +				      <0 0x0aeb0000 0 0x2008>;
> +				reg-names = "mdp", "vbif";
> +
> +				clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
> +					<&gcc GCC_DISP_SF_AXI_CLK>,
> +					<&dispcc DISP_CC_MDSS_AHB_CLK>,
> +					<&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
> +					<&dispcc DISP_CC_MDSS_MDP_CLK>,
> +					<&dispcc DISP_CC_MDSS_VSYNC_CLK>;
> +				clock-names = "bus",
> +					      "nrt_bus",
> +					      "iface",
> +					      "lut",
> +					      "core",
> +					      "vsync";
> +
> +				assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
> +				assigned-clock-rates = <19200000>;
> +
> +				operating-points-v2 = <&mdp_opp_table>;
> +				power-domains = <&rpmhpd SM8450_MMCX>;
> +
> +				interrupt-parent = <&mdss>;
> +				interrupts = <0>;
> +
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port at 0 {
> +						reg = <0>;
> +						dpu_intf1_out: endpoint {
> +							remote-endpoint = <&dsi0_in>;
> +						};
> +					};
> +
> +					port at 1 {
> +						reg = <1>;
> +						dpu_intf2_out: endpoint {
> +							remote-endpoint = <&dsi1_in>;
> +						};
> +					};
> +
> +				};
> +
> +				mdp_opp_table: mdp-opp-table {
> +					compatible = "operating-points-v2";
> +
> +					opp-172000000 {
> +						opp-hz = /bits/ 64 <172000000>;
> +						required-opps = <&rpmhpd_opp_low_svs_d1>;
> +					};
> +
> +					opp-200000000 {
> +						opp-hz = /bits/ 64 <200000000>;
> +						required-opps = <&rpmhpd_opp_low_svs>;
> +					};
> +
> +					opp-325000000 {
> +						opp-hz = /bits/ 64 <325000000>;
> +						required-opps = <&rpmhpd_opp_svs>;
> +					};
> +
> +					opp-375000000 {
> +						opp-hz = /bits/ 64 <375000000>;
> +						required-opps = <&rpmhpd_opp_svs_l1>;
> +					};
> +
> +					opp-500000000 {
> +						opp-hz = /bits/ 64 <500000000>;
> +						required-opps = <&rpmhpd_opp_nom>;
> +					};
> +				};
> +			};
> +
> +			dsi0: dsi at ae94000 {
> +				compatible = "qcom,mdss-dsi-ctrl";
> +				reg = <0 0x0ae94000 0 0x400>;
> +				reg-names = "dsi_ctrl";
> +
> +				interrupt-parent = <&mdss>;
> +				interrupts = <4>;
> +
> +				clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
> +					 <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
> +					 <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
> +					 <&dispcc DISP_CC_MDSS_ESC0_CLK>,
> +					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
> +					<&gcc GCC_DISP_HF_AXI_CLK>;
> +				clock-names = "byte",
> +					      "byte_intf",
> +					      "pixel",
> +					      "core",
> +					      "iface",
> +					      "bus";
> +
> +				assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
> +				assigned-clock-parents = <&dsi0_phy 0>, <&dsi0_phy 1>;
> +
> +				operating-points-v2 = <&dsi_opp_table>;
> +				power-domains = <&rpmhpd SM8450_MMCX>;
> +
> +				phys = <&dsi0_phy>;
> +				phy-names = "dsi";
> +
> +				status = "disabled";
> +
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port at 0 {
> +						reg = <0>;
> +						dsi0_in: endpoint {
> +							remote-endpoint = <&dpu_intf1_out>;
> +						};
> +					};
> +
> +					port at 1 {
> +						reg = <1>;
> +						dsi0_out: endpoint {
> +						};
> +					};
> +				};
> +			};
> +
> +			dsi0_phy: dsi-phy at ae94400 {
> +				compatible = "qcom,dsi-phy-7nm";
> +				reg = <0 0x0ae94400 0 0x200>,
> +				      <0 0x0ae94600 0 0x280>,
> +				      <0 0x0ae94900 0 0x260>;
> +				reg-names = "dsi_phy",
> +					    "dsi_phy_lane",
> +					    "dsi_pll";
> +
> +				#clock-cells = <1>;
> +				#phy-cells = <0>;
> +
> +				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> +					 <&rpmhcc RPMH_CXO_CLK>;
> +				clock-names = "iface", "ref";
> +
> +				status = "disabled";
> +			};
> +
> +			dsi1: dsi at ae96000 {
> +				compatible = "qcom,mdss-dsi-ctrl";
> +				reg = <0 0x0ae96000 0 0x400>;
> +				reg-names = "dsi_ctrl";
> +
> +				interrupt-parent = <&mdss>;
> +				interrupts = <5>;
> +
> +				clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
> +					 <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
> +					 <&dispcc DISP_CC_MDSS_PCLK1_CLK>,
> +					 <&dispcc DISP_CC_MDSS_ESC1_CLK>,
> +					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
> +					 <&gcc GCC_DISP_HF_AXI_CLK>;
> +				clock-names = "byte",
> +					      "byte_intf",
> +					      "pixel",
> +					      "core",
> +					      "iface",
> +					      "bus";
> +
> +				assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK1_CLK_SRC>;
> +				assigned-clock-parents = <&dsi1_phy 0>, <&dsi1_phy 1>;
> +
> +				operating-points-v2 = <&dsi_opp_table>;
> +				power-domains = <&rpmhpd SM8450_MMCX>;
> +
> +				phys = <&dsi1_phy>;
> +				phy-names = "dsi";
> +
> +				status = "disabled";
> +
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port at 0 {
> +						reg = <0>;
> +						dsi1_in: endpoint {
> +							remote-endpoint = <&dpu_intf2_out>;
> +						};
> +					};
> +
> +					port at 1 {
> +						reg = <1>;
> +						dsi1_out: endpoint {
> +						};
> +					};
> +				};
> +			};
> +
> +			dsi1_phy: dsi-phy at ae96400 {
> +				compatible = "qcom,dsi-phy-7nm";
> +				reg = <0 0x0ae96400 0 0x200>,
> +				      <0 0x0ae96600 0 0x280>,
> +				      <0 0x0ae96900 0 0x260>;
> +				reg-names = "dsi_phy",
> +					    "dsi_phy_lane",
> +					    "dsi_pll";
> +
> +				#clock-cells = <1>;
> +				#phy-cells = <0>;
> +
> +				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> +					 <&rpmhcc RPMH_CXO_CLK>;
> +				clock-names = "iface", "ref";
> +
> +				status = "disabled";
> +
> +				dsi_opp_table: dsi-opp-table {
> +					compatible = "operating-points-v2";
> +
> +					opp-187500000 {
> +						opp-hz = /bits/ 64 <187500000>;
> +						required-opps = <&rpmhpd_opp_low_svs>;
> +					};
> +
> +					opp-300000000 {
> +						opp-hz = /bits/ 64 <300000000>;
> +						required-opps = <&rpmhpd_opp_svs>;
> +					};
> +
> +					opp-358000000 {
> +						opp-hz = /bits/ 64 <358000000>;
> +						required-opps = <&rpmhpd_opp_svs_l1>;
> +					};
> +				};
> +			};
> +		};
> +
>   		dispcc: clock-controller at af00000 {
>   			compatible = "qcom,sm8450-dispcc";
>   			reg = <0 0x0af00000 0 0x20000>;
> @@ -2408,10 +2684,10 @@ dispcc: clock-controller at af00000 {
>   				 <&rpmhcc RPMH_CXO_CLK_A>,
>   				 <&gcc GCC_DISP_AHB_CLK>,
>   				 <&sleep_clk>,
> -				 <0>, /* dsi0 */
> -				 <0>,
> -				 <0>, /* dsi1 */
> -				 <0>,
> +				 <&dsi0_phy 0>, /* dsi0 */
> +				 <&dsi0_phy 1>,
> +				 <&dsi1_phy 0>, /* dsi1 */
> +				 <&dsi1_phy 1>,

I think these comments are superfluous now.


Aside from that:


Reviewed-by: Konrad Dybcio <konrad.dybcio at somainline.org>

Konrad

>   				 <0>, /* dp0 */
>   				 <0>,
>   				 <0>, /* dp1 */


More information about the dri-devel mailing list