[PATCH v5 06/10] drm/msm/dsi: add support for DSI-PHY on SM8350 and SM8450
Dmitry Baryshkov
dmitry.baryshkov at linaro.org
Wed Nov 23 21:03:59 UTC 2022
SM8350 and SM8450 use 5nm DSI PHYs, which share register definitions
with 7nm DSI PHYs. Rather than duplicating the driver, handle 5nm
variants inside the common 5+7nm driver.
Co-developed-by: Robert Foss <robert.foss at linaro.org>
Tested-by: Vinod Koul <vkoul at kernel.org>
Reviewed-by: Vinod Koul <vkoul at kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio at linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov at linaro.org>
---
drivers/gpu/drm/msm/Kconfig | 6 +-
drivers/gpu/drm/msm/dsi/phy/dsi_phy.c | 4 +
drivers/gpu/drm/msm/dsi/phy/dsi_phy.h | 2 +
drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c | 119 ++++++++++++++++++++--
4 files changed, 118 insertions(+), 13 deletions(-)
diff --git a/drivers/gpu/drm/msm/Kconfig b/drivers/gpu/drm/msm/Kconfig
index 3c9dfdb0b328..e7b100d97f88 100644
--- a/drivers/gpu/drm/msm/Kconfig
+++ b/drivers/gpu/drm/msm/Kconfig
@@ -140,12 +140,12 @@ config DRM_MSM_DSI_10NM_PHY
Choose this option if DSI PHY on SDM845 is used on the platform.
config DRM_MSM_DSI_7NM_PHY
- bool "Enable DSI 7nm PHY driver in MSM DRM"
+ bool "Enable DSI 7nm/5nm PHY driver in MSM DRM"
depends on DRM_MSM_DSI
default y
help
- Choose this option if DSI PHY on SM8150/SM8250/SC7280 is used on
- the platform.
+ Choose this option if DSI PHY on SM8150/SM8250/SM8350/SM8450/SC7280
+ is used on the platform.
config DRM_MSM_HDMI
bool "Enable HDMI support in MSM DRM driver"
diff --git a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c
index ee6051367679..0c956fdab23e 100644
--- a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c
+++ b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c
@@ -569,6 +569,10 @@ static const struct of_device_id dsi_phy_dt_match[] = {
.data = &dsi_phy_7nm_8150_cfgs },
{ .compatible = "qcom,sc7280-dsi-phy-7nm",
.data = &dsi_phy_7nm_7280_cfgs },
+ { .compatible = "qcom,dsi-phy-5nm-8350",
+ .data = &dsi_phy_5nm_8350_cfgs },
+ { .compatible = "qcom,dsi-phy-5nm-8450",
+ .data = &dsi_phy_5nm_8450_cfgs },
#endif
{}
};
diff --git a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.h b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.h
index 1096afedd616..f7a907ed2b4b 100644
--- a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.h
+++ b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.h
@@ -57,6 +57,8 @@ extern const struct msm_dsi_phy_cfg dsi_phy_10nm_8998_cfgs;
extern const struct msm_dsi_phy_cfg dsi_phy_7nm_cfgs;
extern const struct msm_dsi_phy_cfg dsi_phy_7nm_8150_cfgs;
extern const struct msm_dsi_phy_cfg dsi_phy_7nm_7280_cfgs;
+extern const struct msm_dsi_phy_cfg dsi_phy_5nm_8350_cfgs;
+extern const struct msm_dsi_phy_cfg dsi_phy_5nm_8450_cfgs;
struct msm_dsi_dphy_timing {
u32 clk_zero;
diff --git a/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c b/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c
index 0b780f9d3d0a..7b2c16b3a36c 100644
--- a/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c
+++ b/drivers/gpu/drm/msm/dsi/phy/dsi_phy_7nm.c
@@ -39,8 +39,14 @@
#define VCO_REF_CLK_RATE 19200000
#define FRAC_BITS 18
+/* Hardware is pre V4.1 */
+#define DSI_PHY_7NM_QUIRK_PRE_V4_1 BIT(0)
/* Hardware is V4.1 */
-#define DSI_PHY_7NM_QUIRK_V4_1 BIT(0)
+#define DSI_PHY_7NM_QUIRK_V4_1 BIT(1)
+/* Hardware is V4.2 */
+#define DSI_PHY_7NM_QUIRK_V4_2 BIT(2)
+/* Hardware is V4.3 */
+#define DSI_PHY_7NM_QUIRK_V4_3 BIT(3)
struct dsi_pll_config {
bool enable_ssc;
@@ -116,7 +122,7 @@ static void dsi_pll_calc_dec_frac(struct dsi_pll_7nm *pll, struct dsi_pll_config
dec_multiple = div_u64(pll_freq * multiplier, divider);
dec = div_u64_rem(dec_multiple, multiplier, &frac);
- if (!(pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V4_1))
+ if (pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_PRE_V4_1)
config->pll_clock_inverters = 0x28;
else if (pll_freq <= 1000000000ULL)
config->pll_clock_inverters = 0xa0;
@@ -197,16 +203,25 @@ static void dsi_pll_config_hzindep_reg(struct dsi_pll_7nm *pll)
void __iomem *base = pll->phy->pll_base;
u8 analog_controls_five_1 = 0x01, vco_config_1 = 0x00;
- if (pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V4_1) {
+ if (!(pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_PRE_V4_1))
if (pll->vco_current_rate >= 3100000000ULL)
analog_controls_five_1 = 0x03;
+ if (pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V4_1) {
if (pll->vco_current_rate < 1520000000ULL)
vco_config_1 = 0x08;
else if (pll->vco_current_rate < 2990000000ULL)
vco_config_1 = 0x01;
}
+ if ((pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V4_2) ||
+ (pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V4_3)) {
+ if (pll->vco_current_rate < 1520000000ULL)
+ vco_config_1 = 0x08;
+ else if (pll->vco_current_rate >= 2990000000ULL)
+ vco_config_1 = 0x01;
+ }
+
dsi_phy_write(base + REG_DSI_7nm_PHY_PLL_ANALOG_CONTROLS_FIVE_1,
analog_controls_five_1);
dsi_phy_write(base + REG_DSI_7nm_PHY_PLL_VCO_CONFIG_1, vco_config_1);
@@ -231,9 +246,9 @@ static void dsi_pll_config_hzindep_reg(struct dsi_pll_7nm *pll)
dsi_phy_write(base + REG_DSI_7nm_PHY_PLL_PFILT, 0x2f);
dsi_phy_write(base + REG_DSI_7nm_PHY_PLL_IFILT, 0x2a);
dsi_phy_write(base + REG_DSI_7nm_PHY_PLL_IFILT,
- pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V4_1 ? 0x3f : 0x22);
+ !(pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_PRE_V4_1) ? 0x3f : 0x22);
- if (pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V4_1) {
+ if (!(pll->phy->cfg->quirks & DSI_PHY_7NM_QUIRK_PRE_V4_1)) {
dsi_phy_write(base + REG_DSI_7nm_PHY_PLL_PERF_OPTIMIZE, 0x22);
if (pll->slave)
dsi_phy_write(pll->slave->phy->pll_base + REG_DSI_7nm_PHY_PLL_PERF_OPTIMIZE, 0x22);
@@ -788,7 +803,7 @@ static void dsi_phy_hw_v4_0_lane_settings(struct msm_dsi_phy *phy)
const u8 *tx_dctrl = tx_dctrl_0;
void __iomem *lane_base = phy->lane_base;
- if (phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V4_1)
+ if (!(phy->cfg->quirks & DSI_PHY_7NM_QUIRK_PRE_V4_1))
tx_dctrl = tx_dctrl_1;
/* Strength ctrl settings */
@@ -844,6 +859,12 @@ static int dsi_7nm_phy_enable(struct msm_dsi_phy *phy,
if (dsi_phy_hw_v4_0_is_pll_on(phy))
pr_warn("PLL turned on before configuring PHY\n");
+ /* Request for REFGEN READY */
+ if (phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V4_3) {
+ dsi_phy_write(phy->base + REG_DSI_7nm_PHY_CMN_GLBL_DIGTOP_SPARE10, 0x1);
+ udelay(500);
+ }
+
/* wait for REFGEN READY */
ret = readl_poll_timeout_atomic(base + REG_DSI_7nm_PHY_CMN_PHY_STATUS,
status, (status & BIT(0)),
@@ -858,28 +879,46 @@ static int dsi_7nm_phy_enable(struct msm_dsi_phy *phy,
/* Alter PHY configurations if data rate less than 1.5GHZ*/
less_than_1500_mhz = (clk_req->bitclk_rate <= 1500000000);
+ glbl_str_swi_cal_sel_ctrl = 0x00;
if (phy->cphy_mode) {
vreg_ctrl_0 = 0x51;
vreg_ctrl_1 = 0x55;
+ glbl_hstx_str_ctrl_0 = 0x00;
glbl_pemph_ctrl_0 = 0x11;
lane_ctrl0 = 0x17;
} else {
+ vreg_ctrl_0 = less_than_1500_mhz ? 0x53 : 0x52;
vreg_ctrl_1 = 0x5c;
+ glbl_hstx_str_ctrl_0 = 0x88;
glbl_pemph_ctrl_0 = 0x00;
lane_ctrl0 = 0x1f;
}
- if (phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V4_1) {
+ if (phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V4_3) {
+ if (phy->cphy_mode) {
+ glbl_rescode_top_ctrl = less_than_1500_mhz ? 0x3d : 0x01;
+ glbl_rescode_bot_ctrl = less_than_1500_mhz ? 0x38 : 0x3b;
+ } else {
+ glbl_rescode_top_ctrl = less_than_1500_mhz ? 0x3d : 0x01;
+ glbl_rescode_bot_ctrl = less_than_1500_mhz ? 0x38 : 0x39;
+ }
+ } else if (phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V4_2) {
+ if (phy->cphy_mode) {
+ glbl_rescode_top_ctrl = less_than_1500_mhz ? 0x3d : 0x01;
+ glbl_rescode_bot_ctrl = less_than_1500_mhz ? 0x38 : 0x3b;
+ } else {
+ glbl_rescode_top_ctrl = less_than_1500_mhz ? 0x3c : 0x00;
+ glbl_rescode_bot_ctrl = less_than_1500_mhz ? 0x38 : 0x39;
+ }
+ } else if (phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V4_1) {
if (phy->cphy_mode) {
+ glbl_hstx_str_ctrl_0 = 0x88;
glbl_rescode_top_ctrl = 0x00;
glbl_rescode_bot_ctrl = 0x3c;
} else {
- vreg_ctrl_0 = less_than_1500_mhz ? 0x53 : 0x52;
glbl_rescode_top_ctrl = less_than_1500_mhz ? 0x3d : 0x00;
glbl_rescode_bot_ctrl = less_than_1500_mhz ? 0x39 : 0x3c;
}
- glbl_str_swi_cal_sel_ctrl = 0x00;
- glbl_hstx_str_ctrl_0 = 0x88;
} else {
if (phy->cphy_mode) {
glbl_str_swi_cal_sel_ctrl = 0x03;
@@ -1017,6 +1056,15 @@ static void dsi_7nm_phy_disable(struct msm_dsi_phy *phy)
pr_warn("Turning OFF PHY while PLL is on\n");
dsi_phy_hw_v4_0_config_lpcdrx(phy, false);
+
+ /* Turn off REFGEN Vote */
+ if (phy->cfg->quirks & DSI_PHY_7NM_QUIRK_V4_3) {
+ dsi_phy_write(base + REG_DSI_7nm_PHY_CMN_GLBL_DIGTOP_SPARE10, 0x0);
+ wmb();
+ /* Delay to ensure HW removes vote before PHY shut down */
+ udelay(2);
+ }
+
data = dsi_phy_read(base + REG_DSI_7nm_PHY_CMN_CTRL_0);
/* disable all lanes */
@@ -1040,6 +1088,10 @@ static const struct regulator_bulk_data dsi_phy_7nm_37750uA_regulators[] = {
{ .supply = "vdds", .init_load_uA = 37550 },
};
+static const struct regulator_bulk_data dsi_phy_7nm_97800uA_regulators[] = {
+ { .supply = "vdds", .init_load_uA = 97800 },
+};
+
const struct msm_dsi_phy_cfg dsi_phy_7nm_cfgs = {
.has_phy_lane = true,
.regulator_data = dsi_phy_7nm_36mA_regulators,
@@ -1079,6 +1131,7 @@ const struct msm_dsi_phy_cfg dsi_phy_7nm_8150_cfgs = {
.max_pll_rate = 3500000000UL,
.io_start = { 0xae94400, 0xae96400 },
.num_dsi_phy = 2,
+ .quirks = DSI_PHY_7NM_QUIRK_PRE_V4_1,
};
const struct msm_dsi_phy_cfg dsi_phy_7nm_7280_cfgs = {
@@ -1102,3 +1155,49 @@ const struct msm_dsi_phy_cfg dsi_phy_7nm_7280_cfgs = {
.num_dsi_phy = 1,
.quirks = DSI_PHY_7NM_QUIRK_V4_1,
};
+
+const struct msm_dsi_phy_cfg dsi_phy_5nm_8350_cfgs = {
+ .has_phy_lane = true,
+ .regulator_data = dsi_phy_7nm_37750uA_regulators,
+ .num_regulators = ARRAY_SIZE(dsi_phy_7nm_37750uA_regulators),
+ .ops = {
+ .enable = dsi_7nm_phy_enable,
+ .disable = dsi_7nm_phy_disable,
+ .pll_init = dsi_pll_7nm_init,
+ .save_pll_state = dsi_7nm_pll_save_state,
+ .restore_pll_state = dsi_7nm_pll_restore_state,
+ .set_continuous_clock = dsi_7nm_set_continuous_clock,
+ },
+ .min_pll_rate = 600000000UL,
+#ifdef CONFIG_64BIT
+ .max_pll_rate = 5000000000UL,
+#else
+ .max_pll_rate = ULONG_MAX,
+#endif
+ .io_start = { 0xae94400, 0xae96400 },
+ .num_dsi_phy = 2,
+ .quirks = DSI_PHY_7NM_QUIRK_V4_2,
+};
+
+const struct msm_dsi_phy_cfg dsi_phy_5nm_8450_cfgs = {
+ .has_phy_lane = true,
+ .regulator_data = dsi_phy_7nm_97800uA_regulators,
+ .num_regulators = ARRAY_SIZE(dsi_phy_7nm_97800uA_regulators),
+ .ops = {
+ .enable = dsi_7nm_phy_enable,
+ .disable = dsi_7nm_phy_disable,
+ .pll_init = dsi_pll_7nm_init,
+ .save_pll_state = dsi_7nm_pll_save_state,
+ .restore_pll_state = dsi_7nm_pll_restore_state,
+ .set_continuous_clock = dsi_7nm_set_continuous_clock,
+ },
+ .min_pll_rate = 600000000UL,
+#ifdef CONFIG_64BIT
+ .max_pll_rate = 5000000000UL,
+#else
+ .max_pll_rate = ULONG_MAX,
+#endif
+ .io_start = { 0xae94400, 0xae96400 },
+ .num_dsi_phy = 2,
+ .quirks = DSI_PHY_7NM_QUIRK_V4_3,
+};
--
2.35.1
More information about the dri-devel
mailing list