[PATCH V2 5/6] drm: bridge: samsung-dsim: Support non-burst mode

[Marek Szyprowski]

On 28.04.2023 15:35, Adam Ford wrote:
> On Fri, Apr 28, 2023 at 7:31 AM Marek Szyprowski
> <m.szyprowski at samsung.com> wrote:
>> On 24.04.2023 12:00, Adam Ford wrote:
>>> On Mon, Apr 24, 2023 at 3:25 AM Marek Szyprowski
>>> <m.szyprowski at samsung.com> wrote:
>>>> On 23.04.2023 14:12, Adam Ford wrote:
>>>>> The high-speed clock is hard-coded to the burst-clock
>>>>> frequency specified in the device tree.  However, when
>>>>> using devices like certain bridge chips without burst mode
>>>>> and varying resolutions and refresh rates, it may be
>>>>> necessary to set the high-speed clock dynamically based
>>>>> on the desired pixel clock for the connected device.
>>>>>
>>>>> This also removes the need to set a clock speed from
>>>>> the device tree for non-burst mode operation, since the
>>>>> pixel clock rate is the rate requested from the attached
>>>>> device like an HDMI bridge chip.  This should have no
>>>>> impact for people using burst-mode and setting the burst
>>>>> clock rate is still required for those users.
>>>>>
>>>>> Signed-off-by: Adam Ford <aford173 at gmail.com>
>>>> This one breaks Exynos-5433 based TM2e board with a DSI panel.
>>> Marek S,
>>>
>>> Thank you for testing!  I knoiw there are several of us who appreciate
>>> your testing this since it's hard to know if something broke without
>>> hardware.  Is there any way you can tell me if the flag is set to
>>> enable MIPI_DSI_MODE_VIDEO_BURST?
>> TM2e board uses the DSI panel operated in command mode and handled by
>> panel-samsung-s6e3ha2.c driver. The MIPI_DSI_MODE_VIDEO_BURST flag is
>> not set by the driver. However, the MIPI_DSI_CLOCK_NON_CONTINUOUS flags
>> is set there. I really have no idea if setting VIDEO_BURST would make
>> sense together with CLOCK_NON_CONTINUOUS or not. Maybe the driver lacks
>> setting it?
>>
>>
>>> I was trying to be diligent about not breaking your boards, but
>>> without your boards, it's difficult.  The theory was that if
>>> MIPI_DSI_MODE_VIDEO_BURST is set and there is a burst clock set in the
>>> device tree, it would use the burst clock.
>>>
>>> As a fall-back I could just simply check for the presence of the
>>> burst_clock_rate instead of both MIPI_DSI_MODE_VIDEO_BURST and
>>> burst_clock_rate.
>> Maybe you should extend your check also for the
>> MIPI_DSI_CLOCK_NON_CONTINUOUS flag? Does it make sense?
> Looking at some of the devices that might attach in the future, It
> appears that ti-sn65dsi86.c sets this flag.  It's a display port
> bridge, so I would expect it to need a variable clock rate similar to
> how the HDMI bridge that I need works.  I am concerned that I make the
> burst clock dependent on MIPI_DSI_CLOCK_NON_CONTINUOUS, it might break
> the Display Port bridge.
>
> I think it's better to just check if the samsung,burst-clock-frequency
> is present in the device tree and use it when present.  If it's not
> present, then fall back to the pixel clock of the connected device.

Right, this sounds rational.

> I looked at a bunch of Exynos parts, and it looks like they all use
> the samsung,burst-clock-frequency device tree setting.  Is that true,
> or did I miss one?

That true. All Exynos based boards with DSI panels use constant DSI 
burst frequency defined in the device tree.


Best regards
-- 
Marek Szyprowski, PhD
Samsung R&D Institute Poland