[PATCH v3 2/5] drm/panel: Add driver for JDI LPM102A188A
neil.armstrong at linaro.org
neil.armstrong at linaro.org
Wed Aug 16 16:49:13 UTC 2023
On 07/08/2023 15:33, Diogo Ivo wrote:
> The JDI LPM102A188A is a 2560x1800 IPS panel found in the Google Pixel C.
> This driver is based on the downstream GPLv2 driver released by Google
> written by Sean Paul [1], which was then adapted to the newer kernel APIs.
>
> [1]: https://android.googlesource.com/kernel/tegra/+/refs/heads/android-tegra-dragon-3.18-oreo/drivers/gpu/drm/panel/panel-jdi-lpm102a188a.c
>
> Signed-off-by: Diogo Ivo <diogo.ivo at tecnico.ulisboa.pt>
> ---
> Changes in v2:
> - tuned backlight delays
>
> Changed in v3:
> - removed "-dsi" from driver name, renamed "control"->"command" (Rayyan Ansari)
> - fix error handling
> - remove enabled/prepared booleans
> - add dc/dc setting function
>
> drivers/gpu/drm/panel/Kconfig | 11 +
> drivers/gpu/drm/panel/Makefile | 1 +
> drivers/gpu/drm/panel/panel-jdi-lpm102a188a.c | 551 ++++++++++++++++++
> 3 files changed, 563 insertions(+)
> create mode 100644 drivers/gpu/drm/panel/panel-jdi-lpm102a188a.c
>
> diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
> index 203c0ef0bbfd..787e6ac6f1e7 100644
> --- a/drivers/gpu/drm/panel/Kconfig
> +++ b/drivers/gpu/drm/panel/Kconfig
> @@ -244,6 +244,17 @@ config DRM_PANEL_JDI_LT070ME05000
> The panel has a 1200(RGB)×1920 (WUXGA) resolution and uses
> 24 bit per pixel.
>
> +config DRM_PANEL_JDI_LPM102A188A
> + tristate "JDI LPM102A188A DSI panel"
> + depends on OF && GPIOLIB
> + depends on DRM_MIPI_DSI
> + depends on BACKLIGHT_CLASS_DEVICE
> + help
> + Say Y here if you want to enable support for JDI LPM102A188A DSI
> + command mode panel as found in Google Pixel C devices.
> + The panel has a 2560×1800 resolution. It provides a MIPI DSI interface
> + to the host.
> +
> config DRM_PANEL_JDI_R63452
> tristate "JDI R63452 Full HD DSI panel"
> depends on OF
> diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
> index 30cf553c8d1d..e5a235017c86 100644
> --- a/drivers/gpu/drm/panel/Makefile
> +++ b/drivers/gpu/drm/panel/Makefile
> @@ -22,6 +22,7 @@ obj-$(CONFIG_DRM_PANEL_INNOLUX_EJ030NA) += panel-innolux-ej030na.o
> obj-$(CONFIG_DRM_PANEL_INNOLUX_P079ZCA) += panel-innolux-p079zca.o
> obj-$(CONFIG_DRM_PANEL_JADARD_JD9365DA_H3) += panel-jadard-jd9365da-h3.o
> obj-$(CONFIG_DRM_PANEL_JDI_LT070ME05000) += panel-jdi-lt070me05000.o
> +obj-$(CONFIG_DRM_PANEL_JDI_LPM102A188A) += panel-jdi-lpm102a188a.o
> obj-$(CONFIG_DRM_PANEL_JDI_R63452) += panel-jdi-fhd-r63452.o
> obj-$(CONFIG_DRM_PANEL_KHADAS_TS050) += panel-khadas-ts050.o
> obj-$(CONFIG_DRM_PANEL_KINGDISPLAY_KD097D04) += panel-kingdisplay-kd097d04.o
> diff --git a/drivers/gpu/drm/panel/panel-jdi-lpm102a188a.c b/drivers/gpu/drm/panel/panel-jdi-lpm102a188a.c
> new file mode 100644
> index 000000000000..5b5082efb282
> --- /dev/null
> +++ b/drivers/gpu/drm/panel/panel-jdi-lpm102a188a.c
> @@ -0,0 +1,551 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright (C) 2014 Google, Inc.
> + *
> + * Copyright (C) 2022 Diogo Ivo <diogo.ivo at tecnico.ulisboa.pt>
> + *
> + * Adapted from the downstream Pixel C driver written by Sean Paul
> + */
> +
> +#include <linux/backlight.h>
> +#include <linux/delay.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/regulator/consumer.h>
> +
> +#include <video/mipi_display.h>
> +
> +#include <drm/drm_crtc.h>
> +#include <drm/drm_mipi_dsi.h>
> +#include <drm/drm_panel.h>
> +
> +#define MCS_CMD_ACS_PROT 0xB0
> +#define MCS_CMD_ACS_PROT_OFF (0 << 0)
> +
> +#define MCS_PWR_CTRL_FUNC 0xD0
> +#define MCS_PWR_CTRL_PARAM1_DEFAULT (2 << 0)
> +#define MCS_PWR_CTRL_PARAM1_VGH_210_DIV (1 << 4)
> +#define MCS_PWR_CTRL_PARAM1_VGH_240_DIV (2 << 4)
> +#define MCS_PWR_CTRL_PARAM1_VGH_280_DIV (3 << 4)
> +#define MCS_PWR_CTRL_PARAM1_VGH_330_DIV (4 << 4)
> +#define MCS_PWR_CTRL_PARAM1_VGH_410_DIV (5 << 4)
> +#define MCS_PWR_CTRL_PARAM2_DEFAULT (9 << 4)
> +#define MCS_PWR_CTRL_PARAM2_VGL_210_DIV (1 << 0)
> +#define MCS_PWR_CTRL_PARAM2_VGL_240_DIV (2 << 0)
> +#define MCS_PWR_CTRL_PARAM2_VGL_280_DIV (3 << 0)
> +#define MCS_PWR_CTRL_PARAM2_VGL_330_DIV (4 << 0)
> +#define MCS_PWR_CTRL_PARAM2_VGL_410_DIV (5 << 0)
> +
> +struct jdi_panel {
> + struct drm_panel base;
> + struct mipi_dsi_device *link1;
> + struct mipi_dsi_device *link2;
> +
> + struct regulator *supply;
> + struct regulator *ddi_supply;
> + struct backlight_device *backlight;
> +
> + struct gpio_desc *enable_gpio;
> + struct gpio_desc *reset_gpio;
> +
> + const struct drm_display_mode *mode;
> +};
> +
> +static inline struct jdi_panel *to_panel_jdi(struct drm_panel *panel)
> +{
> + return container_of(panel, struct jdi_panel, base);
> +}
> +
> +static void jdi_wait_frames(struct jdi_panel *jdi, unsigned int frames)
> +{
> + unsigned int refresh = drm_mode_vrefresh(jdi->mode);
> +
> + if (WARN_ON(frames > refresh))
> + return;
> +
> + msleep(1000 / (refresh / frames));
> +}
> +
> +static int jdi_panel_disable(struct drm_panel *panel)
> +{
> + struct jdi_panel *jdi = to_panel_jdi(panel);
> +
> + backlight_disable(jdi->backlight);
> +
> + jdi_wait_frames(jdi, 2);
> +
> + return 0;
> +}
> +
> +static int jdi_panel_unprepare(struct drm_panel *panel)
> +{
> + struct jdi_panel *jdi = to_panel_jdi(panel);
> + int ret;
> +
> + ret = mipi_dsi_dcs_set_display_off(jdi->link1);
> + if (ret < 0)
> + dev_err(panel->dev, "failed to set display off: %d\n", ret);
> +
> + ret = mipi_dsi_dcs_set_display_off(jdi->link2);
> + if (ret < 0)
> + dev_err(panel->dev, "failed to set display off: %d\n", ret);
> +
> + /* Specified by JDI @ 50ms, subject to change */
> + msleep(50);
> +
> + ret = mipi_dsi_dcs_enter_sleep_mode(jdi->link1);
> + if (ret < 0)
> + dev_err(panel->dev, "failed to enter sleep mode: %d\n", ret);
> + ret = mipi_dsi_dcs_enter_sleep_mode(jdi->link2);
> + if (ret < 0)
> + dev_err(panel->dev, "failed to enter sleep mode: %d\n", ret);
> +
> + /* Specified by JDI @ 150ms, subject to change */
> + msleep(150);
> +
> + gpiod_set_value(jdi->reset_gpio, 1);
> +
> + /* T4 = 1ms */
> + usleep_range(1000, 3000);
> +
> + gpiod_set_value(jdi->enable_gpio, 0);
> +
> + /* T5 = 2ms */
> + usleep_range(2000, 4000);
> +
> + regulator_disable(jdi->ddi_supply);
> +
> + /* T6 = 2ms plus some time to discharge capacitors */
> + usleep_range(7000, 9000);
> +
> + regulator_disable(jdi->supply);
> + /* Specified by JDI @ 20ms, subject to change */
> + msleep(20);
> +
> + return ret;
> +}
> +
> +static int jdi_setup_symmetrical_split(struct mipi_dsi_device *left,
> + struct mipi_dsi_device *right,
> + const struct drm_display_mode *mode)
> +{
> + int err;
> +
> + err = mipi_dsi_dcs_set_column_address(left, 0, mode->hdisplay / 2 - 1);
> + if (err < 0) {
> + dev_err(&left->dev, "failed to set column address: %d\n", err);
> + return err;
> + }
> +
> + err = mipi_dsi_dcs_set_column_address(right, 0, mode->hdisplay / 2 - 1);
> + if (err < 0) {
> + dev_err(&right->dev, "failed to set column address: %d\n", err);
> + return err;
> + }
> +
> + err = mipi_dsi_dcs_set_page_address(left, 0, mode->vdisplay - 1);
> + if (err < 0) {
> + dev_err(&left->dev, "failed to set page address: %d\n", err);
> + return err;
> + }
> +
> + err = mipi_dsi_dcs_set_page_address(right, 0, mode->vdisplay - 1);
> + if (err < 0) {
> + dev_err(&right->dev, "failed to set page address: %d\n", err);
> + return err;
> + }
> +
> + return 0;
> +}
> +
> +static int jdi_write_dcdc_registers(struct jdi_panel *jdi)
> +{
> + /* Clear the manufacturer command access protection */
> + mipi_dsi_generic_write_seq(jdi->link1, MCS_CMD_ACS_PROT,
> + MCS_CMD_ACS_PROT_OFF);
> + mipi_dsi_generic_write_seq(jdi->link2, MCS_CMD_ACS_PROT,
> + MCS_CMD_ACS_PROT_OFF);
> + /*
> + * Change the VGH/VGL divide rations to move the noise generated by the
> + * TCONN. This should hopefully avoid interaction with the backlight
> + * controller.
> + */
> + mipi_dsi_generic_write_seq(jdi->link1, MCS_PWR_CTRL_FUNC,
> + MCS_PWR_CTRL_PARAM1_VGH_330_DIV |
> + MCS_PWR_CTRL_PARAM1_DEFAULT,
> + MCS_PWR_CTRL_PARAM2_VGL_410_DIV |
> + MCS_PWR_CTRL_PARAM2_DEFAULT);
> +
> + mipi_dsi_generic_write_seq(jdi->link2, MCS_PWR_CTRL_FUNC,
> + MCS_PWR_CTRL_PARAM1_VGH_330_DIV |
> + MCS_PWR_CTRL_PARAM1_DEFAULT,
> + MCS_PWR_CTRL_PARAM2_VGL_410_DIV |
> + MCS_PWR_CTRL_PARAM2_DEFAULT);
> +
> + return 0;
> +}
> +
> +static int jdi_panel_prepare(struct drm_panel *panel)
> +{
> + struct jdi_panel *jdi = to_panel_jdi(panel);
> + int err;
> +
> + /* Disable backlight to avoid showing random pixels
> + * with a conservative delay for it to take effect.
> + */
> + backlight_disable(jdi->backlight);
> + jdi_wait_frames(jdi, 3);
> +
> + jdi->link1->mode_flags |= MIPI_DSI_MODE_LPM;
> + jdi->link2->mode_flags |= MIPI_DSI_MODE_LPM;
> +
> + err = regulator_enable(jdi->supply);
> + if (err < 0) {
> + dev_err(panel->dev, "failed to enable supply: %d\n", err);
> + return err;
> + }
> + /* T1 = 2ms */
> + usleep_range(2000, 4000);
> +
> + err = regulator_enable(jdi->ddi_supply);
> + if (err < 0) {
> + dev_err(panel->dev, "failed to enable ddi_supply: %d\n", err);
> + goto supply_off;
> + }
> + /* T2 = 1ms */
> + usleep_range(1000, 3000);
> +
> + gpiod_set_value(jdi->enable_gpio, 1);
> + /* T3 = 10ms */
> + usleep_range(10000, 15000);
> +
> + gpiod_set_value(jdi->reset_gpio, 0);
> + /* Specified by JDI @ 3ms, subject to change */
> + usleep_range(3000, 5000);
> +
> + /*
> + * TODO: The device supports both left-right and even-odd split
> + * configurations, but this driver currently supports only the left-
> + * right split. To support a different mode a mechanism needs to be
> + * put in place to communicate the configuration back to the DSI host
> + * controller.
> + */
> + err = jdi_setup_symmetrical_split(jdi->link1, jdi->link2,
> + jdi->mode);
> + if (err < 0) {
> + dev_err(panel->dev, "failed to set up symmetrical split: %d\n",
> + err);
> + goto poweroff;
> + }
> +
> + err = mipi_dsi_dcs_set_tear_scanline(jdi->link1,
> + jdi->mode->vdisplay - 16);
> + if (err < 0) {
> + dev_err(panel->dev, "failed to set tear scanline: %d\n", err);
> + goto poweroff;
> + }
> +
> + err = mipi_dsi_dcs_set_tear_scanline(jdi->link2,
> + jdi->mode->vdisplay - 16);
> + if (err < 0) {
> + dev_err(panel->dev, "failed to set tear scanline: %d\n", err);
> + goto poweroff;
> + }
> +
> + err = mipi_dsi_dcs_set_tear_on(jdi->link1,
> + MIPI_DSI_DCS_TEAR_MODE_VBLANK);
> + if (err < 0) {
> + dev_err(panel->dev, "failed to set tear on: %d\n", err);
> + goto poweroff;
> + }
> +
> + err = mipi_dsi_dcs_set_tear_on(jdi->link2,
> + MIPI_DSI_DCS_TEAR_MODE_VBLANK);
> + if (err < 0) {
> + dev_err(panel->dev, "failed to set tear on: %d\n", err);
> + goto poweroff;
> + }
> +
> + err = mipi_dsi_dcs_set_pixel_format(jdi->link1, MIPI_DCS_PIXEL_FMT_24BIT);
> + if (err < 0) {
> + dev_err(panel->dev, "failed to set pixel format: %d\n", err);
> + goto poweroff;
> + }
> +
> + err = mipi_dsi_dcs_set_pixel_format(jdi->link2, MIPI_DCS_PIXEL_FMT_24BIT);
> + if (err < 0) {
> + dev_err(panel->dev, "failed to set pixel format: %d\n", err);
> + goto poweroff;
> + }
> +
> + err = mipi_dsi_dcs_exit_sleep_mode(jdi->link1);
> + if (err < 0) {
> + dev_err(panel->dev, "failed to exit sleep mode: %d\n", err);
> + goto poweroff;
> + }
> +
> + err = mipi_dsi_dcs_exit_sleep_mode(jdi->link2);
> + if (err < 0) {
> + dev_err(panel->dev, "failed to exit sleep mode: %d\n", err);
> + goto poweroff;
> + }
> +
> + err = jdi_write_dcdc_registers(jdi);
> + if (err < 0) {
> + dev_err(panel->dev, "failed to write dcdc registers: %d\n", err);
> + goto poweroff;
> + }
> + /*
> + * We need to wait 150ms between mipi_dsi_dcs_exit_sleep_mode() and
> + * mipi_dsi_dcs_set_display_on().
> + */
> + msleep(150);
> +
> + err = mipi_dsi_dcs_set_display_on(jdi->link1);
> + if (err < 0) {
> + dev_err(panel->dev, "failed to set display on: %d\n", err);
> + goto poweroff;
> + }
> +
> + err = mipi_dsi_dcs_set_display_on(jdi->link2);
> + if (err < 0) {
> + dev_err(panel->dev, "failed to set display on: %d\n", err);
> + goto poweroff;
> + }
> +
> + jdi->link1->mode_flags &= ~MIPI_DSI_MODE_LPM;
> + jdi->link2->mode_flags &= ~MIPI_DSI_MODE_LPM;
> +
> + return 0;
> +
> +poweroff:
> + regulator_disable(jdi->ddi_supply);
> +
> + /* T6 = 2ms plus some time to discharge capacitors */
> + usleep_range(7000, 9000);
> +supply_off:
> + regulator_disable(jdi->supply);
> + /* Specified by JDI @ 20ms, subject to change */
> + msleep(20);
> +
> + return err;
> +}
> +
> +static int jdi_panel_enable(struct drm_panel *panel)
> +{
> + struct jdi_panel *jdi = to_panel_jdi(panel);
> +
> + /*
> + * Ensure we send image data before turning the backlight
> + * on, to avoid the display showing random pixels.
> + */
> + jdi_wait_frames(jdi, 3);
> +
> + backlight_enable(jdi->backlight);
> +
> + return 0;
> +}
> +
> +static const struct drm_display_mode default_mode = {
> + .clock = (2560 + 80 + 80 + 80) * (1800 + 4 + 4 + 4) * 60 / 1000,
> + .hdisplay = 2560,
> + .hsync_start = 2560 + 80,
> + .hsync_end = 2560 + 80 + 80,
> + .htotal = 2560 + 80 + 80 + 80,
> + .vdisplay = 1800,
> + .vsync_start = 1800 + 4,
> + .vsync_end = 1800 + 4 + 4,
> + .vtotal = 1800 + 4 + 4 + 4,
> + .flags = 0,
> +};
> +
> +static int jdi_panel_get_modes(struct drm_panel *panel,
> + struct drm_connector *connector)
> +{
> + struct drm_display_mode *mode;
> + struct jdi_panel *jdi = to_panel_jdi(panel);
> + struct device *dev = &jdi->link1->dev;
> +
> + mode = drm_mode_duplicate(connector->dev, &default_mode);
> + if (!mode) {
> + dev_err(dev, "failed to add mode %ux%ux@%u\n",
> + default_mode.hdisplay, default_mode.vdisplay,
> + drm_mode_vrefresh(&default_mode));
> + return -ENOMEM;
> + }
> +
> + drm_mode_set_name(mode);
> +
> + drm_mode_probed_add(connector, mode);
> +
> + connector->display_info.width_mm = 211;
> + connector->display_info.height_mm = 148;
> + connector->display_info.bpc = 8;
> +
> + return 1;
> +}
> +
> +static const struct drm_panel_funcs jdi_panel_funcs = {
> + .prepare = jdi_panel_prepare,
> + .enable = jdi_panel_enable,
> + .disable = jdi_panel_disable,
> + .unprepare = jdi_panel_unprepare,
> + .get_modes = jdi_panel_get_modes,
> +};
> +
> +static const struct of_device_id jdi_of_match[] = {
> + { .compatible = "jdi,lpm102a188a", },
> + { }
> +};
> +MODULE_DEVICE_TABLE(of, jdi_of_match);
> +
> +static int jdi_panel_add(struct jdi_panel *jdi)
> +{
> + struct device *dev = &jdi->link1->dev;
> +
> + jdi->mode = &default_mode;
> +
> + jdi->supply = devm_regulator_get(dev, "power");
> + if (IS_ERR(jdi->supply))
> + return dev_err_probe(dev, PTR_ERR(jdi->supply),
> + "failed to get power regulator\n");
> +
> + jdi->ddi_supply = devm_regulator_get(dev, "ddi");
> + if (IS_ERR(jdi->ddi_supply))
> + return dev_err_probe(dev, PTR_ERR(jdi->ddi_supply),
> + "failed to get ddi regulator\n");
> +
> + jdi->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
> + if (IS_ERR(jdi->reset_gpio))
> + return dev_err_probe(dev, PTR_ERR(jdi->reset_gpio),
> + "failed to get reset gpio\n");
> + /* T4 = 1ms */
> + usleep_range(1000, 3000);
> +
> + jdi->enable_gpio = devm_gpiod_get(dev, "enable", GPIOD_OUT_LOW);
> + if (IS_ERR(jdi->enable_gpio))
> + return dev_err_probe(dev, PTR_ERR(jdi->enable_gpio),
> + "failed to get enable gpio\n");
> + /* T5 = 2ms */
> + usleep_range(2000, 4000);
> +
> + jdi->backlight = devm_of_find_backlight(dev);
> + if (IS_ERR(jdi->backlight))
> + return dev_err_probe(dev, PTR_ERR(jdi->backlight),
> + "failed to create backlight\n");
> +
> + drm_panel_init(&jdi->base, &jdi->link1->dev, &jdi_panel_funcs,
> + DRM_MODE_CONNECTOR_DSI);
> +
> + drm_panel_add(&jdi->base);
> +
> + return 0;
> +}
> +
> +static void jdi_panel_del(struct jdi_panel *jdi)
> +{
> + if (jdi->base.dev)
> + drm_panel_remove(&jdi->base);
> +
> + if (jdi->link2)
> + put_device(&jdi->link2->dev);
> +}
> +
> +static int jdi_panel_dsi_probe(struct mipi_dsi_device *dsi)
> +{
> + struct mipi_dsi_device *secondary = NULL;
> + struct jdi_panel *jdi;
> + struct device_node *np;
> + int err;
> +
> + dsi->lanes = 4;
> + dsi->format = MIPI_DSI_FMT_RGB888;
> + dsi->mode_flags = 0;
> +
> + /* Find DSI-LINK1 */
> + np = of_parse_phandle(dsi->dev.of_node, "link2", 0);
> + if (np) {
> + secondary = of_find_mipi_dsi_device_by_node(np);
> + of_node_put(np);
> +
> + if (!secondary)
> + return -EPROBE_DEFER;
> + }
> +
> + /* register a panel for only the DSI-LINK1 interface */
> + if (secondary) {
> + jdi = devm_kzalloc(&dsi->dev, sizeof(*jdi), GFP_KERNEL);
> + if (!jdi) {
> + put_device(&secondary->dev);
> + return -ENOMEM;
> + }
> +
> + mipi_dsi_set_drvdata(dsi, jdi);
> +
> + jdi->link1 = dsi;
> + jdi->link2 = secondary;
> +
> + err = jdi_panel_add(jdi);
> + if (err < 0) {
> + put_device(&secondary->dev);
> + return err;
> + }
> + }
> +
> + err = mipi_dsi_attach(dsi);
> + if (err < 0) {
> + if (secondary)
> + jdi_panel_del(jdi);
> +
> + return err;
> + }
> +
> + return 0;
> +}
> +
> +static void jdi_panel_dsi_remove(struct mipi_dsi_device *dsi)
> +{
> + struct jdi_panel *jdi = mipi_dsi_get_drvdata(dsi);
> + int err;
> +
> + /* only detach from host for the DSI-LINK2 interface */
> + if (!jdi)
> + mipi_dsi_detach(dsi);
> +
> + err = jdi_panel_disable(&jdi->base);
> + if (err < 0)
> + dev_err(&dsi->dev, "failed to disable panel: %d\n", err);
> +
> + err = mipi_dsi_detach(dsi);
> + if (err < 0)
> + dev_err(&dsi->dev, "failed to detach from DSI host: %d\n", err);
> +
> + jdi_panel_del(jdi);
> +}
> +
> +static void jdi_panel_dsi_shutdown(struct mipi_dsi_device *dsi)
> +{
> + struct jdi_panel *jdi = mipi_dsi_get_drvdata(dsi);
> +
> + if (!jdi)
> + return;
> +
> + jdi_panel_disable(&jdi->base);
> +}
> +
> +static struct mipi_dsi_driver jdi_panel_dsi_driver = {
> + .driver = {
> + .name = "panel-jdi-lpm102a188a",
> + .of_match_table = jdi_of_match,
> + },
> + .probe = jdi_panel_dsi_probe,
> + .remove = jdi_panel_dsi_remove,
> + .shutdown = jdi_panel_dsi_shutdown,
> +};
> +module_mipi_dsi_driver(jdi_panel_dsi_driver);
> +
> +MODULE_AUTHOR("Sean Paul <seanpaul at chromium.org>");
> +MODULE_AUTHOR("Diogo Ivo <diogo.ivo at tecnico.ulisboa.pt>");
> +MODULE_DESCRIPTION("DRM Driver for JDI LPM102A188A DSI panel, command mode");
> +MODULE_LICENSE("GPL");
Reviewed-by: Neil Armstrong <neil.armstrong at linaro.org>
More information about the dri-devel
mailing list